Search Documents

By S. G. Sawyer

The Pittsburgh Safety and Health Technology Center (PSHTC) of the Mine Safety and Health Administration (MSHA) provides engineering and scientific support to the inspectorate personnel of MSHA. One of the Center's myriad roles is to assist in the investigation of mining accidents, especially those involving fatalities. Center personnel utilize forensics to help uncover the causes of accidents and to make technical recommendations on the prevention of future similar mishaps. To exemplify a typical forensic investigation, this paper documents the methodology used in determining the reasons for a boat sinking, which resulted in a double fatality on a mine company pond.

Jan 1, 1997

By Michael Wortley

Metso?s Process Technology and Innovation group is a world leader in mineral processing consulting. A significant amount of this consulting work involves process integration and optimization (PIO) studies, which include investigating the effects of drill-and-blast design and implementation on downstream processing. Critical to these studies is the ability to track specific ore into, and through, the plant. To increase the accuracy of this ore tracking, Metso Process Technology and Innovation (PTI) developed a system to track ore using a radio frequency identification (RFID) transponders technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and, finally, into the concentrator. The system is called SmartTag. Since its commercialization in 2007, SmartTag has been used in the majority of PTI?s consulting projects, and several permanent systems have been installed worldwide.

Jan 1, 2012

By J. E. Friant

The Mini-Disc TM cutter drill bit is a radical design departure from the traditional tri-cone rock drill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-Disc TM drill bit, referred to as the "Disc Bit" has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory cannot shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By Gary B. Glass

In 1997, 92.3% or 235.7 Mt (259.8 million st) of coal produced in Wyoming came from the Wyodak coal zone in the eastern Powder River coalfield. The mined portions of the zone consist of one to three beds of coal with an aggregate thickness between 15 and 33.5 m (50 and 110 ft). The thickest expression is 61 m (200 ft). The delivered coal from this zone averages 0.33% sulfur, 5.12% ash and 19.98 MJ/kg (8,590 Btu/lb.). This coal zone occurs at or near the top of the Paleocene Fort Union Formation, which is overlain by the Eocene Wasatch Formation. There is also production from two coalbeds in the lower portion of the Wasatch at the southern end of the basin. Production of coalbed methane derived from the Wyodak coal zone is currently an estimated 289 Mm3/a (10.2 billion cu ft/year). This production is occurring west and downdip from the coal mines and is increasing each year.

Jan 1, 1998

By S. A. Diatchkov

There is a misconception that mineral-project economic evaluations in the former Soviet Union are either nonexistent or very limited. This is not the case. In fact, there are at least two basic methods that can be utilized to evaluate the vast mineral resources of the Commonwealth of Independent States (CIS). Evaluation procedures are based either on a comparison to known projects, which may rely on limited available data, or on potential-profit calculations, which generally uses more extensive databases. Significant philosophical differences between these systems and those utilized in the Western world include the following: •Under the centralized-government system, the economic evaluation of a mineral project was based on artificially determined mineral prices and costs. Every ten to 12 years, prices for concentrates and metals were established by the Council of Ministers and remained unchanged until the next reconsideration of prices .

Jan 1, 1995

By TOMI GIORGIO DE, Ricardo Tichauer

Mineral exploration is a key factor for success in the mining industry. However, exploration best practices are often ignored in small-scale mining. This works presents the Tichauer-DeTomi Matrix, a methodology that measures the level of compliance of exploration programs in small-scale mining with the industry best practices. The matrix has been applied to three projects in Brazil: an artisanal gold mine in the state of Pará, a small-scale manganese project in the state of Bahia, and a small-scale manganese project in the state of São Paulo. The application of the matrix resulted in indexes that represent the level of maturity of the exploration program in each project and indicate priority actions for reduction of the geological uncertainty. Therefore, the Tichauer-DeTomi Matrix has shown potential to be a useful tool for assessment of geological uncertainty in small-scale mining. As a risk indicator, it may contribute to promoting investment in small-scale mining and development for communities that depend on this activity around the world.

By S. Crewdson

Vertical hoisting of materials using hoists and skips is common in the Mining Industry. These systems have a number of drawbacks, one being limited hoisting capacity at medium depths. FKC-Lake Shore and Metso Flexowell have been developing and installing vertical belts for medium depth shaft applications for many years, progressively going deeper whilst increasing belt capacity. The latest development from Metso the Pocketlift® belt advances this technology allowing higher tonnages to be lifted from greater depths. The design, manufacture, installation and operational experience of a 1818 tonnes capacity, 273 meters vertical lift Pocketlift® system at the White County Coal Pattiki 2 mine is the subject of this work.

Jan 1, 2003

By R. Dorey

The Kennecott Ridgeway Mine in South Carolina is scheduled to complete mining and ore processing in the last quarter of 1999. Tailings are disposed in a 300 acre, lined tailings impoundment. To facilitate closure and reclamation, modification of the tailings impoundment operation has been adopted. Mining involved the sequenced development of two open pits. In 1996 mining of the South Pit was completed and backfilling of the pit with waste rock from the North Pit was initiated and will continue until mining ceases. Both pits will be reclaimed as fresh water lakes. This paper presents the physical, geochemical and hydrogeochemical evaluation of the operational and post operational management of the project. Comparison of the operational monitoring data against predicted performance is reviewed.

Jan 1, 1999

By D. A. Norrgran

The term "secondary recovery" has recently brought on a new meaning in view of the depletion of natural resources, energy conservation, plant optimization, and the environmental consciousness that has led to hazardous waste management, recycling, and secondary processing. Many secondary recovery processes are being developed applying mineral processing technology. Gravity separation, magnetic separation, and flotation have all emerged as implicit methods for recovering residual values from various process streams and hazardous constituents from waste streams. Recently, a technique for concentrating metallics has been successfully reintroduced. Although the concept of the eddy-current separator was developed over a century ago, (Patent 400317 issued to Thomas Edison on March 26, 1889) it was not until this last decade that it gained prominent acceptance. The evolution of permanent magnets has provided a cost effective alternative for the generation of high intensity magnetic fields. High energy permanent magnets have substantially reduced the capital and operating costs over the electromagnetic circuits employed in antecedent eddy-current separators. Specifically, in recent years, the strength of permanent magnets has increased several fold with neodymiun-boron-iron rare earth magnets now providing an energy product of 35 million gauss-oersted. Figure 1 shows the evolution in the strength of permanent magnets. The development of these rare earth magnets has led to the design of circuits possessing a magnetic force an order of magnitude greater than that of conventional permanent magnetic circuits.

Jan 1, 1991

The 6th International Mine Ventilation Congress (IMVC) was held May 17-22,1997, in Pittsburgh, PA. This marked the second time that the IMVC was held in the United States. The first congress, organized in 1975 by the Mine Ventilation Society of South Africa, was held in Johannesburg. Since then, the meetings have been held every four or five years, with the 1979 meeting being held in Reno, NV. This was followed by Harrogot, England, in 1984; Brisbane, Australia, in 1988; and Johannesburg, South Africa, again in 1992. The IMVC provides an international forum in the field of mine ventilation for the purpose of sharing technology and experience. The meetings are attended by ventilation engineers, academics, consultants, government employees and vendors interested in mine ventilation. As was evident from this meeting, significant progress has been made in the field of mine ventilation. However, disasters continue to occur around the world and long-term health problems continue to affect workers. So there is a need for further improvements in ventilation technology. The highlight of the conference was the technical sessions in which more than 80 papers were presented by authors from more than 20 countries. In addition to the technical sessions, the conference featured field trips to a number of mine properties throughout the United States. Five short courses were offered on topics ranging from respirable-dust control to mine fires and explosions. The conference also featured a trade show. It exhibited the latest advances in ventilation equipment, computer application software, consulting and engineering services, and health and safety equipment.

Jan 1, 1997

By S. G. McDowell

This paper discusses the utilization of automation to increase productivity of continuous miners. Automation techniques are used during the design stage to decrease the time required and ensure the accuracy of the design. This is followed by automated manufacturing processes to reduce manufacturing time and improve the quality and consistency of parts. Combined, the result is a more reliable machine which can provide ongoing production capability. With the use of automation to enhance operator effectiveness and monitoring machine condition the productivity of machines is also improved.

Jan 1, 1991

By John J. Peregoy, James E. Downes

INTRODUCTION The U.S. Department of Energy's Waste Isolation Pilot Plant (WIPP) is being constructed to provide permanent storage of radioactive TRU waste materials emanating from military weapons production. These wastes are contaminated with radioactive elements heavier than uranium, thus the name trans-(or beyond) uranic (Uranium wastes). The WIPP site, which is located 26 miles east of Carlsbad, New Mexico, was chosen thru a selection process after the National Academy of Sciences recommended salt deposits as a promising host strata for the storage of radioactive wastes. Throughout the United States numerous DOE facilities have produced and stored defense-generated TRU wastes. Once WIPP becomes operational in the fall of 1989, all sites may ship directly to this repository. A companion project has developed special shipping containers (TRUPACT) for safe transport of materials to WIPP. The WIPP facility is currently composed of surface buildings, three shafts, and underground storage and experimental rooms and tunnels. Frontier-Kemper Constructors, Inc. (FKCI) has nearly completed the construction of the fourth shaft, an intake shaft, to provide additional ventilation to the underground workings. PLANNED SHAFT EXCAVATION METHOD Full-face raise boring ( upreaming ) was the allowable method selected by Frontier-Kemper Constructors for the excavation of the shaft. After arrival of an oil-field type rotary drill rig in December 1987, a 9 inch diameter pilot hole was drilled from the surface to the mine level, a depth of approximately 2145 feet.

Jan 1, 1989

By J. A. M. Cano

An extensive research work was developed by Samarco Mineracao S/A to study the quality characteristics of blast furnace pellets produced with high content of MgO. Comparative blast furnace simulation tests were conducted both in Samarco and foreign laboratories. The objective was to evaluate the behavior of high MgO and normal Samarco pellets in the blast furnace operation. Additives such as dolomitic hydrated lime, dunite and magnesite were used for increasing pellet MgO content. The test results showed that pellets produced with high MgO content are similar in quality to normal Samarco Pellets.

Jan 1, 1991

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 established the Office of Mine Safety and Health (OMSH) within NIOSH and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. Subsequently, Congress provided additional funding to NIOSH to initiate and continue the program. OMSHR has fulfilled this Congressional mandate through annual Broad Agency Announcement (BAA) solicitations, directed Requests for Proposals (RFP) and Inter-Agency Agreements (IAA), and has further expanded the program through capacity building BAA contracts with U.S. university mining departments in the areas of mine ventilation and ground control. This paper describes the extramural funding program and broadly examines the results of the 150+ contracts issued to date, grouped into key focus areas. INTRODUCTION The Mine Improvement and New Emergency Response Act (MINER Act) of 20061 established the Office of Mine Safety and Health Research (functioning as the Office of Mine Safety and Health Research or OMSHR) within the National Institute for Occupational Safety and Health (NIOSH), and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued over 150 contracts focused on worker health and safety. Initial funding for this program was provided by Congress through two Emergency Supplemental Appropriations (ESA) and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation; ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website2 and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously.3"

Jan 1, 2018

By Manfred Jaeger, Klaus Ertmer, Walter Dietrich, Jochen Greinacher, Wilhelm J. Kogelmann

In Europe, novel low-cost excavator-mounted Multi Tool Miner (MTM) systems, consisting of cutter head, hammer, bucket and drill attachments permit one unit to perform multiple tasks replacing several purpose-built machines. At the Weser Tunnel in Germany, cross-passages between the twin tubes were excavated in frozen ground with a remote-controlled mini-excavator equipped with a quick-change cutter head, ripper tooth and bucket. In Switzerland at the N2 interstate near Basel, W. Dietrich AG enlarged a 2-lane tunnel to three lanes with a cutter head mounted on a special excavator. Blasting and heavy hammers were not permitted due to the closeness of the “live” twin tube. At the N20 Zurich bypass, the Joint Venture of Jaeger, Frutingerand AHB excavates highway tunnels, some with extremely large cross sections, conventionally. A cutter head mounted on an excavator removes the rock shattered by blasting precisely to the pay line, thus preserving the rock’s self-supporting capacity preventing subsidence and damages to water resources and buildings on the surface under low overburden.

Jan 1, 2003

High pressure grinding mills have been successfully introduced in the industry. They offer the possibilities for capacity increase of existing plants and reduction of operating costs. Further metallurgical advantages in gold and copper are possible. The plants in operation are running in different applications and modes of operation. They can be installed in a combination with SAG and ball mills or in a stand-alone mode. In combination with other grinding mills, it has to be investigated how the HPGR can be installed to reach the full efficiency. This paper describes the possibilities to implement high pressure grinding rolls and shows by case studies the potential of savings which could be reached

Jan 1, 1996

By Nick Barton, Khosrow Bakhtar

Two plate load tests of 1 m2 area were per- formed in a pressure tunnel at the Rocky Mountain Pumped Hydro Project. Reaction for the 250 tons loading in this 10.5 meter diameter tunnel was provided by deeply anchored, diverging rock bolts, eight per load frame. Pressure build up to 2.5 MPa was provided by circular flatjacks. Rock deformation was recorded at depths of approximately 0.3, 0.9, 1.2, 1.8 and 3.3 meters using axially located multiple position borehole extensometers. The tests were performed in representative units of massive shale and thin to medium bedded siltstone. Stress was built up in four equal steps to 2.5 MPa, held constant for one week for creep monitoring, then unloaded, reloaded and unloaded over a period of one day. The most deformable unit was the massive shale which exhibited 1.3 mm of permanent deformation at the surface after the first loading and unloading cycle, which included 0.36 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 2.6 mm, following a maximum deformation at the surface of approximately 3.6 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 0.4 GPa when loading, and 0.3 GPa when unloading. The thin to medium bedded siltstone exhibited only 0.17 mm of permanent deformation at the surface after the first loading-unloading cycle, which included only 0.05 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 0.27 mm, following a maximum deformation at the surface of approximately 0.53 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 6.2 GPa when loading and 21.9 GPa when unloading.

Jan 1, 1986

By Douglas W. Huber

During the past decade, a general awareness of the need for and subsequent development of increased safety in United States coal mines has taken place. Government and industry alike were stimulated into accelerating their actions through unacceptable accident statistics and costs (in terms of human misery dollar values). Those of us who work in the United States coal industry are aware of the development of governmental controls on nine safety. Both Federal and State regulations have placed increased responsibility upon mine owners and operators to insure a safe working environment and to provide training for miners. No other industrial group of workers has received such attention or, in our opinion, deserves it more.

Jan 1, 1982

By Matthew Geary, Stephen J. Marino, Jordan A. Schreiner

"INTRODUCTION Project Overview The Southeast Collector (SeC) is a new 15km long 3.0m internal diameter wastewater tunnel designed by Hatch Mott MacDonald (HMM) that twins the existing 2.6m diameter York-Durham Sewage System (YDSS) tunnel. Both sewage tunnels are located north of the City of Toronto in Ontario, Canada. The SeC provides much needed conveyance capacity for the rapidly growing York Region population, supporting development until 2036 and increasing sewage system security (Hatch Mott MacDonald and AECOM 2011). Construction of the SeC will also permit flows of the twinned section of the YDSS to be bypassed in order to clean, inspect and carry out any essential maintenance within the YDSS tunnel. Although owned and operated by York Region, the SeC spans two regional municipalities beginning upstream from the intersection of Ninth Line and Rouge Bank Drive in the City of Markham in York Region to the downstream Finch Avenue and Valley Farm Road intersection in the City of Pickering in Durham Region. See Figure 1 for the SeC and YDSS alignment. The project includes 19 shafts and chambers with depths ranging from 8 to 48m in addition to seven facilities supporting the operation and maintenance of the sewer. The construction contract was awarded to Strabag Inc. in July 2011 for $291M CAD. Construction Management services were provided by a joint venture team of Hatch Mott MacDonald and AECOM. Existing York-Durham Sewage System The YDSS tunnel was completed in 1979 and was constructed using an open shielded TBM with ribs and lagging temporary support, followed by installation of a 380mm thick unreinforced cast-in-place (CIP) concrete final lining. The YDSS sewer system has numerous connections that accumulate flows from various urban areas within York Region. The section of the YDSS twinned by the SeC flows under gravity conditions and had been putting a strain on the municipality’s potential for population and development growth having reached its maximum capacity of 420 ML/d. According to the York Region’s Water and Wastewater Master Plan, the existing YDSS would not have been able to handle wet weather flows past 2016 (Genivar and XCG Consultants 2009). The dependability of this section of the YDSS is also of concern because it is the main and critical connection between the sewer systems upstream and the downstream Duffin Creek Water Pollution Control Plant (WPCP)."

Jan 1, 2016

By W. M. Luff

Introduction The Brunswick No. 12 mine is located about 27 km (17 miles) southwest of Bathurst, New Brunswick. The deposit is a stratiform massive sulfide deposit occurring in a series of sedimentary and volcanic rocks of the Tetagouche Group. These rocks are generally considered to be Ordovician in age. Ore reserves at Brunswick No. 12 are 104 Mt (115 million st) grading 3.72% lead (Pb), 9.01% zinc (Zn), 0.32% copper (Cu), and 97.9 g/t (2.8 oz per st) silver (Ag). Production in 1984 was 3.5 Mt (4 million st) at 3.57% Pb, 8.91% Zn, 0.32% Cu, and 100 g/t (2.9 oz per st) Ag. Total payable silver production that year was 211 t (6.8 million oz). This made Brunswick one of the largest silver producers in Canada. Bathurst-Newcastle area and Brunswick Mining Interest in the Bathurst area was aroused in 1897 when W. Hussey discovered an iron formation at Austin Brook, just south of Brunswick No. 6 deposit. This area, and the current No. 6 area, was explored from 1897 to 1907. Iron ore was mined at Austin Brook from 1907 to 1913 and from 1942 to 1943. Any occurrence of sulfides was overlooked until 1952. In 1952, M. J. Boylen Enterprises investigated the small sulfide body associated with the Austin Brook iron formation. Other electromagnetic anomalies associated with the iron formation were investigated. The No. 6 deposit was found late in 1952, when hole B12 intersected 97.5 m (320 ft) of massive sulfides. The No. 12 deposit, 10 km (6 miles) to the north, was found in 1953. More than 30 massive sulfide deposits have since been identified in the Bathrust area. In the 1950s, St. Joe Lead Co. did extensive test work on the No. 6 and No. 12 deposits, including shafts at No. 12, lateral development at No. 12, and testing at both deposits.

Jan 10, 1986