Search Documents

By N. Sano

The chromium oxide in stainless steel slags usually exists as Cr2O3. However, there is a possibility that it is oxidized to hazardous CrO3 after disposal or during use. Therefore, some technical developments to reduce chromium oxide by using a smelting reduction technique have been reported recently. This paper describes the fundamentals of the technique which have been applied to ferrochromium production and reviews the recent results in literature.

Jan 1, 2004

By A. E. Hall, R. N. Taylor, J. G. Taylor

The introduction of tunnel-boring machines to South African gold mines has created problems and challenges which accompany any new technique. This paper describes the experience gained in this field, especially in the design and erection of a tunnel borer and in boring and environmental conditions.

Jan 1, 1978

By S. Kamalpour

It has been observed that the productivity of ferromanganese furnaces, and the stability of metal and slag compositions, vary considerably according to the type of coke used as reductant. However, the desired properties of coke for optimum furnace performance are not well understood. In this investigation, the behaviour of four cokes, which exhibited a wide range of performance in ferromanganese production, was investigated by means of laboratory simulations of reducing conditions in the furnace. The Stationary Charge in Controlled Environment (SCICE) technique was used to simulate the conditions in the furnace shaft. Batches of raw materials, mixed in the same proportions as used in practice, were heated at fixed rates to 900, 1100 and 1300°C then cooled. The mass loss was used as a measure of the degree of reduction. Conditions in the lower part of the furnace were simulated by means of melt-reduction experiments in which lumps of coke were drilled out to form crucibles in which enriched ferromanganese slags were reduced at 1500 and 1550°C then cooled. An examination of the raw materials and the cooled, reacted charges using a variety of analytical and characterization techniques enabled the sequence of reaction and changes in morphology of the raw materials to be followed. This enabled an understanding of the behaviour of the cokes during reduction to be developed, which was then used to explain the observed performance of the cokes in practice. By relating the observed behaviour of the cokes in the laboratory tests to measurable properties of the unreacted cokes and to their observed performance in practice, it was shown that to achieve high productivity and good furnace performance, cokes should be selected to have moderately high reactivity towards CO2 (Boudouard reactivity) relative to conventional iron blast furnace cokes.

Jan 1, 2004

By Chad W. Brown

"A study of five commercially available solvent-extraction diluents in combination with three commercially available extractants under sub-Saharan African copper solvent-extraction conditions yielded intriguing results. A variety of physical and chemical property analyses showed that the diluents have some property differences, but overall the properties are similar and provide comparable solvent-extraction performance. Although each physical chemical property technique provides useful information, no individual test result suffices for prediction of diluent performance. Furthermore, a diluent should be evaluated within the conditions for which it is targeted to determine a true measure of performance. Overall, the diluents studied possess appropriate physicochemical properties for sub-Sahara Africa copper solvent-extraction conditions and can be utilized to achieve efficient, safe and reliable operations. INTRODUCTION Background Today, commercial SX diluents are available globally from a limited number of manufacturers. Production quality and consistency of these diluents have improved tremendously over the past 20 years. For example, diluent flash points have been increased incrementally to improve transport and handling while reducing fire hazards. In addition, properties have been successfully modified to minimize evaporative losses, ultimately reducing SX plant raw material costs. Diluent manufacturers have also focused on meeting performance requirements of SX plants, including eliminating components detrimental to SX operations, such as olefinic groups that can react with various species resulting in changing phase-disengagement properties over time, as well as ensuring that proper hydrocarbon components are present within diluent mixtures to maintain good reagent–metal complex solubility. These challenges have been met in the midst of ever-increasing stringent environmental regulations. Sub-Saharan Africa copper SX operations pose a unique set of conditions for diluents due to inherent ore compositions and the associated high reagent concentrations required for complete copper extraction. Chevron Phillips Chemical Company, LP has been manufacturing hydrocarbons and hydrocarbon-based diluents since the mid-80s, applying this experience to identify the physical properties considered crucial for proper performance in SX operations. This paper documents the findings of a study utilizing commercially available diluents in combination with extraction reagents commonly utilized in African SX operations to evaluate the relative performance of the diluents under sub-Saharan Africa copper SX conditions."

Jan 1, 2015

By David Mitchell, Daan Delport, Frik Marx, Mike Shapiro

The use of copper cooling elements to enhance refractory lining life in pyrometallurgical vessels is common in modern furnace design. Copper elements typically incorporate a base panel with cast in cooling passages and an integral extended surface (formed of pins, fins or similar) onto which suitable refractory material is cast. The metallic, conducting parts are located towards the cold face of the lining, with the refractory material interposing between the coolers and the process. The coolers are designed to arrest wear of the refractory material by freezing a layer of slag or partially reacted material onto the hot face, thereby rendering the lining inert to further attack [1]. These coolers have achieved success in new furnaces and relining of existing vessels. The freeze layer is prone to mechanical damage during operational and process instability. The coolers must be capable of extracting the additional heat flux under upset conditions to facilitate rapid self-repair of the freeze layer and prevent further refractory wear in the intermittently exposed areas. However, operational experience has shown that the high heat flux capabilities of the copper coolers have some disadvantages, especially in processes producing vapours which form corrosive compounds when condensing onto the cold surfaces of the coolers. When corrosive conditions develop, the entire composite will fail due to loss of structural integrity, and as a result of leaks from the cooling water passages. This paper describes recent developments in the approach to the design and manufacture of copper cooler panels customized to achieve specified heat fluxes and temperature profiles, thereby reducing the formation of corrosion mechanisms in applications with corrosive gaseous environments and enhancing refractory lining life. Condensation formation prevention is achieved by adjusting the geometry of the cooler and selection of suitable materials of construction.

Jan 1, 2007

Mine wide, underground wireless communications are possible with the use of Ultra Low Frequency (ULF) technology. Due to the propagation through rock of ULF radio signals a relatively small antenna can provide communications coverage over a complete mining operation. Starting as a Personal Emergency Device (PED) for emergency messaging to miners under all circumstances, the ULF communications system has grown to include capabilities of remote control of underground equipment such as pumps and fans and centralised blasting initiation. This technology is now in use on 5 continents having lately made it onto the African mining scene. The paper and presentation will provide the audience with the benefit from international mining know-how in this technology as well as local African experiences. A recent commissioning exercise for example, is expected to pay for itself in electricity savings within a few months. These and other results from practical demonstrations and usage will be covered. This novel technology becomes an integral part of the daily operating infrastructure of a mine with immediate safety and business benefits. It is able to reduce capital expenditure and is designed for ease of routine operational use. The paper will conclude with insights into current R&D for further development of this technology.

Jan 1, 2007

By P. J. Bhonde, R. D. Angal, R. H. Tupkary

Manganese imparts numerous beneficial mechanical properties. Hence it finds extensive application in iron, steel and non-ferrous sector. Prevalently, it is incorporated in the form of master alloys i.e. 'ferromanganese'. In India, ferromanganese is mainly the inexpensive and paramount source of availability of manganese. Various conventional and non-conventional techniques of ferromanganese production have been adopted in past and present. However, these techniques have demerits viz. high refractory, energy consumption, losses of valuables in slag and fumes. Also geographical co-ordinates of the plant restricted the manufacturer to prefer an appropriate process. Accordingly, the industrially implemented methods had reliance on availability of infrastructure, energy, mineral resources, grade of raw material, outlay of labor, environmental compatibility of technique etc. In view of the liberalized economy and the gap scenario in the supply and demand of ferromanganese, the authors felt it indispensable to explicitly bridge up this vacuum by initially designing a simple energy conserving, eco-friendly, low capital investment technique for decarburization of ferromanganese. Measurement of the data involved studying the impact of rate governing parameters on the process kinetics. This laboratory scale investigation is expected to escalate the Mn/C quotient of high carbon ferromanganese. Key Words: ferromanganese, carbon, carbide, decarburization, rate, kinetic

Jan 1, 2007

By C. Wade, A. Swart, M. Dworzanowski

AngloGold Ashanti operate a pyrite flotation plant at their East Gold Plant, Acid Plant and Flotation Plant (EGAF) metallurgical complex within their Vaal River operations in the North West province in South Africa. The flotation plant feed is reclaimed pyrite rich tailings and the concentrate produced is used as the source of sulphur for the EGAF acid plant. The sulphuric acid produced is in turn used for the recovery of uranium at the Vaal River South uranium plant. The original flotation plant built in 1960 was based on the use of many small volume flotation cells and was becoming very expensive to operate and its age severely limited further operation. A decision was taken in 2005 to replace this plant with a new one based on fewer, larger volume flotation cells. This paper describes the benefits of using larger volume flotation cells in this new flotation plant when compared to the smaller volume flotation cells in the old plant. The benefits of the new plant include a smaller plant footprint, fewer flotation cells, fewer pumps, no distribution boxes, simpler piping, a greater flotation volume and a reduction in installed power. The saving in capital cost could not be quantified because of the age of the old plant. The savings in operating cost will arise from fewer operators, less maintenance and reduced power consumption. The new plant has not been in operation long enough to quantify the benefits in operating cost and metallurgical performance. However, recovery improvements can be expected given the greater flotation volume (increased residence time) and the installation of larger, more efficient flotation cells.

Jan 1, 2007

By K. Ford, R. Urquhart, D. Hobbs

CIS countries are home to some of the world's largest producers of chrome, manganese and silicon ferro alloys and leading suppliers to world export markets. The region's ferro alloys production is rising faster than demand from its domestic steel industry - unit alloy consumption in domestic steelmaking is in fact falling as process efficiencies improve - and there is significant spare capacity available to increase production. CIS producers enjoy certain strategic advantages in the production of ferro alloys - for example, captive ore sup-plies, low power and labour costs - but must also meet certain challenges - such as lower labour productivity and greater distance to market than some of their competitors. CIS producers are ambitious but new investment is needed to upgrade some aging plants and overhaul outdated process technologies if they are to be more competitive with the world's leading producers and address the environmental issues that are now moving up the agenda. This paper describes the structure of the region's ferro alloys industry and discusses its advantages and disadvantages by alloy and by country. It considers how the ongoing process of restructuring and new investment in the industry might move forwards, based on its strengths and weaknesses, technical and environmental factors and the strategies of the main players. It asks how the industry might maximise its substantial potential - in particular, for the production of chrome and manganese ferro alloys - and examines the implications this holds for all global ferro alloys players.

Jan 1, 2007

By B. W. Lee, P. O?Shaughnessy

The practice of manganese ferroalloy smelting has traditionally been based on utilising oxide ores which typically contain a high level of manganese. This preference for oxides has even been extended to the modification of natural carbonates into nodulized oxides. However smelting practices developed over the past 30 years have created a market for natural manganese carbonate ores, driven in part by the unique properties that this type of ore can offer. An understanding of the mineralogy of carbonate ore and its thermal properties has provided important information which enables furnace operators to take full advantage of the chemical differences. However changes to traditional operating practices have been necessary. Once furnace operations using natural and unmodified carbonate ore have been mastered, the unique chemical features of manganese carbonate ore are able to contribute, not only to new product development, but also to cost savings. The use of natural manganese carbonate ore is now a well-established aspect of the industry. The sustained increase in demand for carbonate ore worldwide over the past several years confirms acceptance of its quality. There are effectively few limits to its successful use.

Jan 1, 2004

By Fadeela Saloojee, Frank K. Crundwell

"Pressure leaching is an option for copper recovery from chalcopyrite. Leaching takes place at high temperatures and pressures in the presence of an oxidising agent. This work shows how the performance of pressure leaching circuits may be improved by optimising the configuration of autoclaves and the heat-removal method. The objective was achieved by creating an autoclave model by combining mass balances, energy balances and population balances. A base-case circuit consisting of a single autoclave was chosen, and this base case was compared with options for increasing capacity by adding more autoclaves to the circuit. These capacity–increase options include circuits in which the additional autoclave is added in parallel, in series and in series with thickening between the two autoclaves. The copper extraction, productivity and cooling requirements for these options are compared. The series circuit with inter-stage thickening has the highest extraction and productivity, however, the cooling duty in the first autoclave is high. In addition to comparing circuit options, three options for heat removal were investigated: cooling coils, quench water and flash recycling. The flash-recycle option results in the highest copper extraction, and the quench-water option gives the lowest copper extraction. INTRODUCTION Background Copper sulfide ores and concentrates containing chalcopyrite are typically hard to leach under atmospheric conditions. Smelting of these ores may also be a challenge, due to the inability of smelting processes to handle low-grade ores, as well as impurities such as arsenic and antimony. Alternative hydrometallurgical routes to treating chalcopyrite are therefore required. One option is pressure leaching, which is the focus of this work. In the pressure leaching process, sulfide ores and concentrates are leached in autoclaves at temperatures of 200 to 220°C and a pressure of about 3000 kPa (Schlesinger et al., 2011). An oxidising agent, usually oxygen, is required to oxidise sulfide ions to sulfate ions. The oxidation of sulfur to sulfate is exothermic; consequently, a method of heat removal is necessary in order to maintain the temperature in the autoclave."

Jan 1, 2015

By S. E. Olsen, T. Færden, G. Tranell, T. Lindstad, J. Lubetsky

The authors are lead authors for chapter 4.3 ?Emissions from Ferroalloy Production? in ?2006 IPCC Guide-lines for National Greenhouse Gas Inventories, Volume 3?. The paper discusses the methods to calculate and report emissions from the production of ferrosilicon, silicon-metal, ferromanganese, silicomanganese and ferrochromium alloys, as well as the basis for the methods and choice of emission factors. CO2 is the main greenhouse gas emission from ferroalloy production, accounting for about 95 % of the total CO2-equivalents. The most accurate method of determining emissions is to base the calculations on reported amounts and analyses of reducing agents and carbonate ores used in the process. If analyses are not available, typical CO2 emission factors for the different reducing agents are recommended. If neither reliable amounts nor analyses of all reducing agents are known, default generic CO2 emission factors for the type of ferroalloy multiplied with amount produced, can be used. The CO2 produced from bio-carbon (charcoal and wood chips) should be reported but will not be accounted for in national emissions. If any bio-carbon is used, the default generic CO2 emission factors cannot be applied. CH4 accounts for less than 1 % of the total emission of CO2-equivalents. Default emissions factors for CH4 are given for the production in open or semi-closed furnaces of silicon-metal and ferrosilicon. In the production of FeMn, SiMn and FeCr in closed furnaces the gas containing CO,CO2 and volatiles can be combusted in boilers and N2O may be formed. While reporting is not required, IPCC Guidelines recommend that the N2O-content in the off-gas is measured.

Jan 1, 2007

By M. Shapiro, L. A. le Grange, B. Henning

Effective pyrometallurgical process vessel design requires accurate assessment of the heat fluxes through the walls of the furnace. This is particularly important for freeze lining operation which is designed to protect refractory materials exposed to chemically corrosive molten contents, or facilitate high temperature operation when the refractory materials are used at conditions close to their service limits. Numerical modelling of fluid flow and heat transfer in process vessels is often used to aid in the design of process vessels. Sophisticated models are used to analyse the three dimensional flow and heat transfer predicting the effects of electrical heating, magnetic stirring, buoyancy, shear forces, various cooling effects and ultimately heat fluxes at the walls of the furnace and refractory. Traditionally these models are applied to the separate single fluid systems in a vessel such as the freeboard region including the arc, the slag region and the metal bath. Boundary conditions such as shear forces and heat fluxes between connecting regions such as the slag and metal bath are either estimated or carried over from separate solutions. Shortcomings in these traditional approaches include the estimation of sometimes critical boundary conditions leading to unreliable heat flux calculations. Also when boundary conditions are carried over between solutions, the process is difficult to set up, time-consuming and finally not fully coupled. In this paper the definition and results of a fully integrated numerical model of a complete arc furnace are presented. The most important mechanisms acting in an arc furnace were considered, including the fields of electrical potential, current, magnetism, momentum, heat transfer and radiation. Temperature dependant properties included electrical conductivity, density, viscosity, and thermal conductivity. The geometry consists of the freeboard, the arc, slag, metal baths and different refractory regions. Although the combined model of air, slag and metal would be defined as a multi-phase problem it is not solved as such. Instead the different fluids are separated by sets of special solid baffles. These baffles allow the implicit transfer of current, magnetism, heat transfer and shear forces between the different fluids and disallow mixing of the separate fluids. The strengths of the integrated model are threefold: Firstly, it provides robustness in defining the geometry and boundary conditions for the overall model. Secondly, it provides the capability to switch on and off individual mechanisms such as buoyancy, magnetic stirring and shear forces in order to observe their individual importance. Finally, it provides a useful tool in the design process through its ability to obtain results of parameter changes in short time scales.

Jan 1, 2004

Poorly designed sampling protocols generally result in high project risk by artificially increasing grade variability (ie the nugget effect). Sample collection, preparation and assay protocols that suit the ore type, together with QA/QC systems, will reduce this risk. All reporting codes (eg JORC, 2004) require the Competent Person to consider the quality and implication of sampling and assaying programs. High sampling errors beget higher project uncertainty; despite this fact, sampling does not receive the attention it deserves. The case studies presented show that many sampling issues frequently go unrecognised or unaddressed, resulting in poor project decisions during exploration through to feasibility and production. The overall conclusion is that correct sampling is critical to mining project success and that there is often a need for its optimisation.

Jan 1, 2007

CSIRO Mineral has recently developed a new electron microprobe based system for characterizing zircon grains from heavy minerals sand deposits. The system acquires cathodoluminescence (CL) spectra, X-ray and backscattered electron (BSE) signals in parallel. By scanning over a specified target area, CL wavelength and X-ray element distribution maps of polished zircon grains can be acquired. Post-inspection of the combined dataset using in-house developed software enables correlations between chemistry and structure to be investigated. The new method offers significant benefits over traditional CL and BSE techniques in that direct comparison with the elemental concentrations over the same region is now achievable. By combining the electron microprobe results with data for the same mapped region obtained via a nuclear microprobe, significantly better detection limits (~ 1ppb) for elements with atomic numbers greater than iron are possible. The ability to measure spatially related analytical data and then investigate the correlation of the CL spectra with chemical data is an important advancement in the characterization of zircons. Key words: zircon, characterization, cathodoluminescence, backscattered electron, electron microprobe, nuclear microprobe, chimage, proton induced x-ray emission.

Jan 1, 2003

By W. Dziurzynski, S. Nawrat, A. Krach

The paper presents research on the influence of the goaf methane inflow on a fire. The problem was investigated by a computer simulation of a fire developing in a goaf. A relevant mathematical model of the fire was selected, which considered both burning of coal and methane. The combustion process is very sensitive on the oxygen and methane concentrations, which was indicated on graphs of the fire temperature evolution. Examples of computer simulation for various location of the fire were considerd. Analysys of results confirms the influence of the content of the goaf methane on development of fires.

Jan 1, 2003

By J. Kempken, T. A. Schreiter, R. Degel, H. Schmieden

Keywords: Pyrometallurgy, SMS Demag, Germany, submerged arc furnace, ferro alloys, non-ferrous, FeCr, FeNi, FeMn, copper, cobalt, slag cleaning, PGM, rectangular furnace After a short summary of the SMS Metallurgy part of the SMS group, the paper will focus on Submerged Arc furnace technology. After general aspects of furnace design, the focus will shift to different applications and their specific furnace requirements. Finally, a state-of-the-art design tool as well as a new invention to improve slag-cleaning technology will be featured.

Jan 1, 2006

By D. Boshoff

The ability of an explosive to break rock is influenced considerably by the extent of confinement in the blasthole. It is believed that confinement is improved by the use of adequate stemming. The aim of this paper is to present the results of the first and second stages of developing a stemming performance testing rig for small diameter boreholes. The rig was used to compare and contrast the performance of different designs of products. The results showed that different stemming products have differences in terms of their functionality, which can have a major impact on the efficiency of rock breaking. Two test procedures were used, one through the exclusive use of compressed air and the second using a purpose-built high pressure test rig with small quantities of explosives. Both tests were used to identify and evaluate the ability of various stemming products to resist the escape of explosive gas through the collar of a blasthole. An investigation was done to determine the types of stemming products most commonly used in South African underground hard rock mines, and these products were used during the tests. The first stage of tests using compressed air only did not prove adequate to predict with certainty the pressure behaviour in the borehole of a particular product under high pressure conditions. The purpose-built high pressure test rig also did not prove to be a very effective tool to test stemming products under high pressure conditions. The test rig incorporated only the effect of gas pressure on the stemming product, and excluded the effect of the shock wave. This study therefore proved that to take into account only the gas pressure generated in the blasthole is not sufficient to effectively test stemming product performance.

Jan 1, 2011

By J. A. Bakken, M. Tangstad, P. A. Eidem

In the submerged arc production of ferromanganese, sillicomanganese and ferrochromium, the coke bed characteristics play an important role. The basic mechanisms of electric current conduction in the coke be dare not yet fully understood, but important parameters are the material resistivity of coke and the contact resistance between the coke particles. Preliminary tests indicate that the contact resistance is of great importance to the bulk resistance of the coke bed. An apparatus measuring the material resistivity and contact resistance of carbon materials has been developed. Both graphite and industrial coke have been tested. The material resistivity tests were performed on single particles to ensure that the effects of pores and cracks were included and the contact resistances were excluded. Two geometries were tested to obtain the contribution of the contact resistance to the total resistance of two connecting particles. The tests were performed in an inert atmosphere at temperatures and current levels found in industrial submerged arc furnaces. The results show that the method has a satisfactory reproducibility. It was found that the contact resistance is about 10 times higher than the resistance of the material when two particles are in perfect contact and that the resistivity of SSAB coke is more than 10 times higher than that of the graphite at room temperature, but with increasing temperature the difference decreases. For SSAB coke the general trend is that both the resistivity and the contact resistance decrease with increasing temperature.

Jan 1, 2007

By J. F. Papp

In the United States, chromium has been consumed in three major markets: chemical, metallurgical, and refractory. The predominant end use for chromium in the United States is in the metallurgical market as an alloying element in the production of stainless steel. In addition to being a major stainless steel-producing country, the United States is a major world producer of chromium-containing chemicals and has used substantial amounts of chromite ore for refractory applications. Chromium use is not easily further subdivided within the chemical and refractory industries because there is insufficient publicly available information to do so; however, chromium use can be subdivided among metallurgical industry uses based on the American Iron and Steel Institute (AISI) reported shipments of stainless steel by market classification (agricultural, aircraft, automotive, etc.). It is the goal of this study to determine the distribution of U.S. chromium apparent consumption among major markets in the United States. The distribution is expressed in the form of dimensionless fractions that are computed based on documented chromium consumption by major market. The distribution of chromium among markets within the metallurgical market is computed in a similar manner. Distribution factors are first computed for the major markets, then for markets that are subdivisions of the metallurgical market. The distribution of chromium among major markets has changed substantially over the time period of analysis. The fraction of chromium consumed by the metallurgical market has increased while that of the chemical and refractory markets has declined. Within the metallurgical market, the service industry market accounts for the greatest fraction of chromium consumption followed by transportation. Electrical, machinery, and fabricated products markets account for a substantial share of the metallurgical chromium consumption.

Jan 1, 2004