Search Documents

By C. -J. Rick

The ferroalloy market is characterized by a very long communication distance between the consumer and the producer. This has created a situation where it has been difficult to change ferroalloy properties. In this paper different FeNi and FeCr-compositions are discussed and their merits for stainless steel-makers in different situations are compared using the process models applied at Outokumpus Avesta works and Acerinox's Columbus operation Keywords Ferroalloy design, ferrochrome, ferronickel, stainless steel making, UTCAS software.

Jan 1, 2010

By J. M. Eriksen, T. Rosenqvist, H. Elstad, S. Seim, A. Hildal

The titanium industry demands high titanium feedstock for their processes. As rutile resources are limited, ilmenite has become the most important titanium source. Ilmenite smelting is an important part of upgrading ilmenite to high titanium feedstock. In the year 2005, upgrading of ilmenite by smelting, producing a slag with 80-90% Ti02, accounted for approximately 40% of the feedstock to the Ti02 pigment industry. In ilmenite smelting molten iron is produced together with a slag, which in addition to titanium oxide contains iron oxide as well as various impurity oxides of manganese, magnesium, silicon, aluminium, etc. Titanium is present mainly as Ti02 but partly also as Ti203. It is known that the concentration of Ti203 increases with decreasing concentration of FeO, but this dependency is affected by the nature of the impurity oxides. Sigurdson and Moore1 showed that slags high in CaO and MgO had a lower concentration of Ti203 than slags high in Si02 for the same amount of FeO. Pistorius2 showed in 2002 that if the impurity oxides MnO and MgO are counted, on a molar basis, as FeO, and Cr203, V203 and part of the A1203*), as Ti203, industrial slags will have a composition close to that of the M305 phase, where M denotes the elements Ti, Fe, Mn, etc, and which has the pseudobrookite structure. However, for equilibrium with liquid metallic iron he computed, by means of a computer program FACT, that the slag equilibrium composition is represented by a curved line in the ternary phase diagram FeTi03-TiO2-Ti2O3, but with a significantly higher concentration of trivalent titanium than actually observed in the industrial slags, and he discussed various mechanisms by which the slag during solidification could change its composition to a lower Ti203 content, but the possibility that the computed compositions might be wrong was not mentioned. Trane113 found in her research on titaniferous silicate slags a lower Ti3+/ Ti4+ ratio than that which is computed by the FACT program. The purpose of the present investigation was to study the equilibrium composition of Fe-Ti-O slag in equilibrium with liquid metallic iron, as well as the effects of impurities such as Si02, CaO and MgO on the slag composition. Industrial slags from TINFOS Titan and Iron KS (TTI) will also be discussed and their compositions will be plotted in the ternary phase diagram. These are slags produced from Tellnes ilmenite, quite high in magnesium and iron. Experimental In the past, equilibrium studies of the Fe-Ti-O slag system were difficult when it came to producing the slag. It was difficult to find a suitable crucible for the meltings. The highly corrosive slag would attack all known refractories, and the metal would attack metallic crucibles such as those made of platinum and molybdenum. In the present investigations the slag-metal combination was prepared in a high-frequency induction furnace with a vertically segmented water-cooled copper crucible. The crucible is shown in Figures 1 a and 1b. It was designed by the Australian Nuclear Science and Technology Organisation (ANSTO) with power from a 75 kVA high-frequency generator (750 kHz) supplied by Farfield Electronics Pty, Ltd, Australia. This enabled the slag-metal combination to be melted with turbulent stirring and is expected to be isothermal. The entire temperature gradient

Jan 1, 2007

By M. Viljoen

South Africa has produced more than a third of the total gold mined throughout history and remains a major although, until recently, no longer the largest producer of gold. South African gold production peaked in 1970 with an output of 1 000 t, a major component of the western world?s gold production, with the development of the country?s economy having been based largely on this mineral wealth. The costs and difficulties of increasingly deep-level mining, coupled with increasing labour costs and the low gold price until relatively recently, have seen production fall steadily since then, with the closure of many mines including those of the Central Rand Goldfield in the mid seventies. Thus in 1998, only 464 t were produced, with 342 tons being produced in 2004. In 2006, 275 tons of gold were produced and after more than 100 years was the last year as the world?s largest gold producer. In 2008 gold production was 221 tons, making South Africa the third largest gold producer after China (292 t) and the USA (234 t). Gold production would have been lower if it had not been for massive tailings dam retreatment operations that started in the late seventies, including in the Central Rand Goldfield. Mining of a remaining deep and lower grade shallow resources has now also become a major focus and has recently lead to a rebirth of reef mining on the Central Rand Goldfield.

Jan 1, 2009

By A. F. Mulaba-Bafubiandi

Pseudomonas spp was isolated from mine water and tailings samples collected from mining effluents and mine dumps in the Gauteng and Northern provinces of South Africa respectively. Adsorption properties of Pseudomonas spp were then tested for the removal of Cu and Co initially from their synthetic sulphate solutions, subsequently from effluents derived from metallurgical operations. The effects of experimental conditions such as pH, temperature, time, volume and metal concentration on the efficiency of the biosorption process were studied. Absorption of 45% Cu (pH 6, 37°C, 24 hours) and 40% Co (pH 6, 37°C, 24 hours) was observed from solutions with low concentrations (0.07 M). A maximum of 73% and 65% of Cu and Corespectively were recovered from the mine water samples derived from effluents.

Jan 1, 2009

By Neal Harries

The monitoring of rock slopes is a common procedure in the management of hazards associated with slope instability. Slope stability radar has become widely accepted as the state-of-the-art method for management of hazards associated with unstable slopes in open pit mines. This is confirmed by the rapid adoption of the technology since inception in mid 2003, with over 70 GroundProbe slope stability radars now in use at open pit operations throughout the World. The use of a monitoring system such as slope radar to identify slope hazards is only part of the solution to minimise the consequences associated with slope instability. The presence of the hazard must also be effectively communicated to the mine personnel, so that the correct response to the hazard can be enacted, and the risk mitigated to an acceptable level. In some surface mines, due to the geotechnical characteristics of the rock mass, hazards can develop rapidly; with slopes progressing from stability to ultimate collapse in just hours. In these situations, it is vital that efficient systems are developed to evacuate the area of the pit affected. Such a system has been developed by GroundProbe in South Africa, with the vital driving force for the project being provided by the Anglo Platinum Mogalakwena mine operation based at Mokopane. The mine based development of the system was perceived as an essential aspect in the development of the successful system. From an early stage, the mine provided essential input on both hardware and software developments to allow the system to be rapidly integrated into the mining operation. This paper describes the pit evacuation alarm system that was developed and discussed the benefits obtained from a mine based development program.

Jan 1, 2008

By R. Layton

Expert Systems Technology (EST) is becoming more and more widespread in both its range of applications and the public interest. It appears to be capable of performing tasks unmatched by other techniques. Within the mining industry a large body of unsolved problems now appear to have a solution. This paper examines the current state of EST both in the context of the history of Artificial Intelligence and current efforts at building mining expert systems. It provides recommendations for those wishing to get involved, and outlines the problems for those who believe that expert systems are capable of anything and everything. The paper also provides a detailed analysis of limitations of current EST that must direct research into more fundamental, commonsense areas than have been extensively covered before.

Jan 1, 1987

By D. Farrow

Future development of kimberlite mines is now focused on mining at deeper levels. The consequences are increased difficulty and costs of the mining operations. The decisions on investments require accurate resource evaluation and quantification of the risk. In the decision process the first step consists in choosing the number of boreholes sampling the pipe relative to the level of uncertainty that can be accepted. The uncertainty in the volumes of rocks of different types can be assessed as soon as we can estimate these volumes from a given borehole layout and calculate the error by means of its variance for instance. In theory this can be achieved by using geostatistical techniques (‘transitive theory’), but in practice the calculation of the error on volumes can be achieved in very particular cases, assuming some regular sampling patterns. A different approach has been chosen based on simulations, giving maximum flexibility to reproduce the reality of the sampling procedure. The idea is to simulate the geometry of several ‘possible’ pipes with their internal geology and estimate them by kriging. Several experimental errors are obtained on which risk analysis can be performed. The aim is to find a feasible method to perform the simulations with reasonable chance to correctly represent the reality, without data on the pipe extension. The methodology applied is based on some hypotheses that can be assessed by the geologist as well as by the geostatistician. The procedure assumes a geological model based on current knowledge including appropriate geostatistical variation. What make these simulations specific and powerful in this case comes from the fact that the boundaries between the different rock-types can be simulated using a transformation of the real 3D space into a 2D space defined by means of polar coordinates. Ultimate transformations to account for smoother variations with morphological transformations allow the generation of realistic pipe geometries on which sampling pattern can be used to evaluate the estimation errors. By estimating the simulated pipe geometries with different boreholes layouts a risk curve expressing the uncertainty in the volumes of the different rock-types versus the number of holes can be developed.

Jan 1, 2003

Material transfer in underground mines often relies on ore and waste pass systems. Over the years the authors have investigated the design and performance of orepass systems in several Canadian and South African mines. It has been recognized that while most mining operations have either implicitly or explicitly clearly defined objectives, in the design and successfully operate orepass systems there seems to be an absence of a strategy on how to best attain these goals. Consequently, it is not surprising that the majority of operations reviewed by the authors experience a number of problems of varying degrees of severity and economic consequences. This is illustrated by reference to both South African and Canadian operations. The second part of this paper focuses on a review of tactical interventions to rectify orepass problems or mitigate their impact. The paper closes with a framework for a flexible strategy for the design and operation of orepass systems. Keywords orepass; orepass design; orepass stability; orepass rehabilitation; orepass operation; orepass strategy.

Oct 1, 2013

By F. Bourgouin

Thirty-one years ago, African leaders met in Lagos for the drafting of the Lagos Plan of Action for the Economic Development of Africa, 1980?2000. The main objective of the plan was to increase Africa?s self-sufficiency and in this regard, the plan had a section pertaining specifically to redressing the ills of an unproductive mining and minerals industry and harnessing its potential for socio-economic development. However, if we look at the nature of this sector on the continent today, its characteristics resemble the diagnosis of the sector given in the plan back in 1980: lack of information on endowments of minerals; lack of value added in the sector; low development and use of those endowments that are not of interest to transnational corporations (TNCs); and most importantly, low contribution to socio-economic development. The primary consequence of the lack of visible benefits to African states, despite growth and development of the sector in terms of increased mining activity led by Foreign Direct Investment is that countries with mining industries are characterized by dysfunctional internal processes. Improvements in governance, monitored with indices such as those set out in the Extractive Industries Transparency Initiative, the Millennium Development Goals, and other such ?good governance? agendas, are being asserted. However, before we prescribe the introduction of initiatives or guidelines based upon highly subjective norms which we believe to fit this diagnosis, it is necessary to review how it is that we got to this situation that we are in today. How is it that, 31 years after the Lagos Plan of Action, we have not seen any major changes in the role the industry can play in socio-economic development, despite the vast increase in mining activity on the continent?

Jan 1, 2011

By R. W. Ottermann, N. D. L. Burger, A. J. von Wielligh, P. R. de Wet, J. L. Steyn

Underwind and overwind protection system concepts for mine hoist shafts were developed in conjunction with and for the Safety in Mines Research Advisory Committee (SIMRAC). End-of-wind operation of mine hoists is the most hazardous aspect of mine hoisting, carrying the highest risk of loss of life, injuries to workers and loss of production. Systems operating mechanically and with local actuation were developed. This was done in order to remove the increased risk associated with dependency on remote or external energy and information supply associated with most existing protection systems. The proposed underwind protection system concept absorbs the energy of motion of a conveyance overrunning the design lower limit of travel by drawing a metal strip through a set of rollers. This action causes dynamic cyclic plastic bending of the strip material that converts the kinetic and potential energy of the conveyance into strain energy of the metal. In the concept design a pair of cable slings attached to the strips catch the overrunning conveyance and transfer the retardation force. The proposed overwind protection system concept absorbs the energy of motion of a conveyance overrunning the design upper limit of travel by early detaching of the conveyance from the hoist cable. This detaching is carried out via an additional humble hook activation mechanism fitted at a sufficient height below the spectacle plate to allow the conveyance to retard to standstill under gravity before it would crash into the spectacle plate. The conveyance so brought to rest is prevented from falling by means of jack catches on the conveyance interacting with a rack (toothed profile) fitted on the guide rails in the retardation zone. Scale models (1:10 scale) of both protection systems were designed for conformance with established retardation standards. The retardation standards were limited by the requirement of passenger safety in retarding cages. The models were then built and tested in a 1:10 scale shaft model. Retardation performance close to the required levels was achieved. The retardation distance required should allow such systems to be retrofitted to most existing shafts. Given the simplicity and robustness of the designs

Jan 1, 2003

By F. M. Russell

Scheduling the extraction and rates of production for an underground mining operation is a common task carried out during the life of a mine, from the initial feasibility study through to the final production phase. The scheduling process can be complex when several requirements have to be satisfied, for example, match mill capacity and maximize net present value while constrained by mining sequence and availability of resources. Many mines have computer programs relevant to their operation but because they are site-specific they need considerable reprogramming to be adapted to other operations. Other methods currently in use also suffer drawbacks: manual spreadsheets are laborious, computerized spreadsheets cannot handle sufficient constraints, and operations research techniques require a complex mathematical model to be set up. The use of network analysis techniques has been proposed previously but the unavailability, until recently, of easily used computer programs has not allowed this approach to be developed. There are now many programs which can be used; however, the particular program which has been adapted to mine scheduling is Metier's 'Artemis-PC' running on IBM-XT or compatible machine. The use of network analysis offers many advantages, including the use of a logical mining sequence; activities can be as detailed as required; related activities can be readily incorporated, and costs can be easily extracted. A heuristic approach is necessary to optimize the schedule, but the ease and speed of program execution enables this to be readily achieved, while leaving the mining engineer in full control. The paper discusses the problems encountered in mine scheduling and current solutions. It then details the use of network analysis techniques and the application of the Artemis-PC program to solve mine scheduling problems.

Jan 1, 1987

By R. Kosmicki

Wet end components of centrifugal slurry pumps used in the hydraulic transport of solids are subject to substantial erosive wear. Accurate prediction of the casing wear rate and location for a particular duty is beneficial for correct pump selection and design, maintenance planning, and elimination of emergency shutdowns. CFD multiphase simulation using the Eulerian-Eulerian approach is being applied successfully to determine the velocity fields and solids concentration in the centrifugal pump, allowing for accurate predictions of casing wear patterns resulting from sliding abrasive wear. Simulation results for various single domain and multi-domain (multistage) multiphase simulations are discussed. Emphasis is placed on results from a 3-dimensional, multi-stage transient, multiphase simulation and comparison to field data.

Jan 1, 2007

When designing coal mine roof support, it is necessary to account for the uncertainties and variability that inherently exist within the rock mass and support elements. The performance of a support system is affected by these uncertainties, which are not taken into account in the current deterministic design methodologies used in South Africa. The key to the design of a roof support system is a better understanding of roof behaviour and uncertainties that can been countered during extraction. This paper sets out to develop a method that takes all uncertainties that exist within the rock mass and the mining process into account and provides a quantitative risk-based design methodology.

Jan 1, 2009

The special mixing requirements for backfilling are discussed, and the problems associated with the mixing of coarse and deslimed slurries, as well as the tailings from the gold plant are outlined. The mixing of binders which are used to strengthen backfill and the parameters for the scale-up of mixer pilot plant work are also discussed

Jan 1, 1988

By M. D. G. Salamon

If a transition from one equilibrium state to another occurs during the course of mining, energy transfer takes place in the rock mass, which is assumed to be an elastic continuum. The energy components are defined as follows: the work done by external and body forces, W; the increase in stored energy in the mass, Uc; the strain energy in the rock mined during the transition, Urn; the work done on mine support or backfill, Ws; and the released energy, Wr. The energy balance is defined as (W + Urn) - (Uc + Ws) = Wr> 0, where the first set of components in parentheses represents the sources of energy, while that of the second corresponds to the known modes of energy expenditure and the component on the right is the unaccounted-for energy surplus, which must be released and dissipated in some form. The inequality Wr ~ Urn> 0 applies. Expressions for the energy components are derived first for the general case and then for the 'slit' modal used to simulate tabular excavations. Through specific examples, the importance of the progressive nature of mining is emphasized. The size of the steps used to enlarge the excavations appears to play a significant role in the mode of energy transfer. This observation forms the basis of the second paper in this series of two papers.

Jan 1, 1984

By X. Jia

The ability to perform three dimensional imaging at micron-scale resolution of real mineral floc sediments and structures using commercially available Micro X-ray Tomography (XMT) instrumentation can be used for the analysis of aggregates and granules, liberation and dewatering of sediments. This paper presents are view of recent work by the authors relevant to the mining and minerals industries. It covers three main topics: X-ray imaging of agglomerates and multi-component mineralic particles,, permeability of sediments, and dissolution of granules with potential application to heap leaching.

Jan 1, 2008

By G. A. Matthrsuis, R. N. Morris

The paper identifies two zones in a Leeds flotation cell. The ratio (13)of the dissipative forces and the interfacial tension force acting on a bubble and a solid particle are shown mathematically to be proportional to the square of the particle diameter for the quiescent zone and inversely proportional to the particle diameter for the turbulent zone. To locate the range of operation, correlations were established for the bubble diameter through photography and bubble counts. 13was found to be fairly constant in the particle size range 38 to 150 ",m, and the level of turbulence unlikely to affect the bubble-particle attachment and hence the beneficiation efficiency. This was verified in a series of flotation runs with a standard Leeds cell and a modified cell of twice the height to increase the capacity of the quiescent zone. A series of tests on the size range 300 to 600 ",m showed that the turbulence level had a marked effect on the cell performance through a relative improvement in the beneficiation efficiency due to the increased height of the cell. To identify the significant variables in the size range 38 to 150 ",m, a factorial design was carried out. Promoter dosage and particle size were found to be significant, aeration rate and impeler speed being insignificant at the 95 per cent confidence level. Multiple regression correlations were established for the recovery of organic material, mineral rejection, and beneficiation efficiency.

Jan 1, 1988

By R. G. B. Pickering

The Faculty of Engineering at the University of the Witwatersrand and the Mining Technology Division of the CSIR have co-operated to define the problems associated with deep level mining and in this paper they will identify what they consider to be the critical areas requiring technological solutions. This perspective will then be applied to work currently being carried out by both the organizations and gaps for additional developments will be identified. Finally the Co-operative Research Centre methodology operating in Australia is described. The purpose of this CRC is to provide a vehicle for R&D co-operation to develop and implement technologies which will increase the competitiveness of the mining industry. A further objective is to develop an appropriately skilled human resource base.

Jan 1, 1996

A set of six design principles for rock engineering was developed by Bieniawski: design objectives; minimum uncertainty; simplicity of design components; state-of-the-art practice; optimization; and constructability. These principles translate into a ten-step design process. Although this methodology was developed for rock engineering, it is applicable to any design process, feasibility study, etc. Diligent use of such a process will ensure that a defensible design or evaluation has been carried out. Recently a ?strategic conversation? process has been identified by Ilbury and Sunter that includes the following ten steps: scope; players; rules of the game; key uncertainties; scenarios; SWOT analysis; options; decisions; measurable outcomes; and meaning of winning. A comparison of these steps with those of the design process shows a remarkable correlation. This is perhaps not surprising since engineering design is a strategic up-front issue, and front end loading in a project is critical to achieve the expected project performance. Based on the close correlation between the strategic conversation and engineering design processes, a circular design process, rather than a linear process, is proposed. The ?circle of design? better reflects the importance of review and monitoring in the two phases of successful design and implementation?defining the design, and executing the design.

Jan 1, 2009

By J. J. Taute, N. B. du Preez

"A well-performing solvent-extraction circuit is a key part of producing good quality copper cathode. To ensure consistent operation, a good understanding of the circuit’s operation and an ability to rapidly troubleshoot key parameters is required. This paper briefly discusses the modeling of solventextraction circuits. The paper then goes on to discuss the determination of key performance parameters from plant data and comparing these with the circuit models to quantify circuit performance. The identification and troubleshooting of circuit issues is presented with a worked example. INTRODUCTIONA well-performing solvent-extraction (SX) circuit is a key part of producing good quality copper cathode. To ensure a consistent, high-quality operation, a good understanding of the circuit performance is required. Evaluating the performance of an SX circuit is an extensive topic. The objective of this paper is to focus on the evaluation that the metallurgist should be performing on a regular basis using flow and concentration data. This paper does not cover important topics, such as crud management, phase continuity, or organic management. Some basic SX modeling concepts are first be presented. The calculation of the parameters is then presented with a brief discussion and recommended ranges (where applicable). A worked example is used to provide a basis for further discussion on the evaluation of the calculated parameters and use of data collected.BASIC SOLVENT-EXTRACTION MODELING CONCEPTSThis section presents the basic modeling concepts used in SX simulation packages currently available. SX reagent suppliers have invested significant time and effort into collecting data on the performance of their reagents under different conditions. Based on these data, suppliers have developed packages which they normally make available to their clients for free. These are typically used for process design and plant optimization studies. For example, BASF developed ISOCALCTM and CYTEC Industries developed MINCHEM® and MEUMTM.Chemistry of Copper Solvent ExtractionLiquid–liquid extraction involves the selective transfer of a substance between two immiscible liquid phases by controlling the relative solubility in each phase. In the case of copper SX, the exchange is typically achieved by an oxime-based chelating mechanism. In particular, mixtures of aldoxime and ketoxime are normally used in conjunction with modifiers. More detail on this extensive topic can be found in Schlesinger et al. (2011)."

Jan 1, 2015