Search Documents

By Kym L. Morton

Ground water and associated pore pressure represent elements which can have a negative impact on surface mining and slope stability. Ground water flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data was available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By M. J. Kanda

"The design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. This is commonly done using two well-established methods – limit equilibrium and numerical modelling. The research described in this paper compares the outputs of analyses using these two methods with regard to factor of safety and probability of failure, taking into account technical factors associated with each method and other factors such as material parameters and their variabilities. Results show that technical factors such as number of slices and slip circles, number and type of finite elements, and the stress reduction factor can all affect the results of stability analyses. Factors not taken into account in limit equilibrium analyses, such as dilation, in situ stress, and locked-in stresses can affect the outputs significantly. The research has focused particularly on the predicted location of the failure surface, the resulting volume of failure and, most significantly dependent on this volume, the predicted risk associated with slope failure. The results presented show that there is good agreement between the outputs of the two methods regarding factor of safety and probability of failure. However, the same is not the case with regard to volume of failure and hence risk, which can be very dependent on the methods of analysis and their input parameters. The research is not exhaustive, and there are many other factors that could affect the results of slope stability analyses that were not investigated. Some such factors are mentioned in the paper.IntroductionThe design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. The traditional method of stability analysis used limit equilibrium (LE) methods, and this approach continues to be used. Numerical modelling (NM) packages are now also commonly used in slope stability analyses. The outputs from these analyses provide the factor of safety (FOS) and probability of failure (POF) of the slope. Since the capabilities of the two approaches are different, there can be some variations in FOS and POF outputs and in the predicted location of the failure surface. These variations can affect the predicted volume of failure, and this could in turn have a significant effect on the risk associated with the potential failure (Read and Stacey, 2009). Researchers such as Chiwaye and Stacey (2010) have found that LE analyses underestimate the predicted failure volume, unlike NM methods."

Jan 1, 2016

By E. Dervaric

The main purpose of this paper is to introduce the main strategic restructuring aspects of companies that are directly (coalmines) or indirectly (companies that depend on coalmines) linked to coalmining. An attempt is also made to determine the principal factors required for the successful execution of a restructuring process in companies focused on the basic activities of coalmining, such as companies that provide supporting activities. The restructuring process exerts an influence on the whole area that relies on coalmining. So coordination of activities among the government, the local community, and the coalmine is very important. This is the major premise of this paper. The first section of the paper focuses on identifying and analysing the key factors in restructuring and a selection of key methods, drawing on past and present practice. The key factors to be considered in a model of enterprise restructuring in the coalmining sector are considered. The second section is dedicated to the actual design of the model of enterprise restructuring in the coal industry. The proposed model is based on positive experiences in the restructuring of coalmining companies in Europe, with an emphasis on Slovenia, successful approaches to crisis management in corporations, and identifying key areas in bringing about a strategic turnarounds in company operation. To support the argument for the key business areas, a brief summary of empiric findings has been included to demonstrate the applicability of the proposed model and the restructuring process. The summary is based on the survey done in both Slovenian coalmining companies (especially in Velenje Coal Mine) and their subsidiaries. The conclusion integrates key findings and outlines issues for further consideration and discussion. Keywords: restructuring, coalmining, Velenje Coal Mine, strategic factors, restructuring model.

Jan 1, 2008

By A. Montini

The problems encountered in the design of control systems for milling cir- cuits when the model of the system and the model parameters are uncertain are discussed. Considering these uncertainty factors has led to the development of a technique that gives a quantitative assessment of real system stability, reveals the trade-offs between performance and stability and helps the designer in deciding what level of model complexity to use in the controller design. Furthermore, it allows for on- or off-line optimization of the milling circuit performance as it provides the base for the design of a controller which is stable over the plant operating range.

Jan 1, 1987

The development of short- and medium-term mine production schedules in isolation from each other has meant that only a local optimum can be achieved when each scheduling phase is carried out. The globally optimal solution, however, can be achieved when integrating scheduling phases and accounting for the interaction between short-term and medium-term activities simultaneously. This paper addresses the task of integrating short- and medium-term production plans by combining the short-term objective of minimizing deviation from targeted mill feed grade with the medium-term objective of maximizing net present value (NPV) into a single mathematical optimization model. A conceptual sublevel stoping operation comprising 30 stopes is used for trialling segregated and integrated scheduling approaches. Segregated medium- and short-term scheduling using separate models achieved an NPV of $42 654 456. The final scheduling approach involved integrating the two scheduling horizons using the newly-developed globally optimal integrated production scheduling model to achieve an NPV of $42 823 657 with smoother mill feed grade. The larger the stope data set, the larger the difference between the two scheduling approaches is likely to be. At the very least, an integrated approach ensures feasibility across the two scheduling horizons, which cannot always be assumed when using a segregated approach.

Jan 1, 2012

Geological mapping makes an important contribution to orebody knowledge during the evaluation of structurally controlled gold veins. Orebody knowledge comprises an understanding of mineralization characteristics relevant to evaluation, mining, processing and environmental issues and allows project expectations to be realistically set. Structural interpretation to define continuity and mineralization controls is a key part of geological risk reduction and the reporting mineral resources using the JORC and other codes. The Dolgellau gold belt is a small British field that produced an estimated 150 000 oz from narrow quartz veins. Historical records, recent exploration and production data, published material, and accessible surface and underground exposure provide a valuable case study. Previous mapping has shown the general geometry of vein systems, but tends to accentuate gross geological continuity. Recent work has attempted to determine internal vein architecture and examine the significance of the historical views of ore shoot controls. The work resulted in the definition of vein continuity scenarios for the gold belt and evaluation expectations associated with each. This has, in turn, led to a realistic view of what can be achieved from an evaluation and project development perspective.

Jan 1, 2009

By G. Ferrara

The mathematical framework of a well-established model proposed earlier by the authors for the screening process is briefly recalled. Some numerical methods for the application of the model, concerning numerical solution of the equations and parameter estimation, are indicated. Some applications of the model to improve screening operations, sizing of screen, simulation of screening and of integrated plant operations are discussed, and the computer software to be used for these purposes is described in detail.

Jan 1, 1987

By K. Cole, D. Mesa, P. Brito-Parada, M. R. van Heerden

Turbulence in mechanical flotation cells, achieved via an impeller, plays a key role in keeping particles in suspension, dispersing air bubbles, and promoting particle-bubble collision. However, studying the hydrodynamics of a flotation cell is not a simple task, due to the complex nature of flotation systems which are opaque, turbulent, multiphase and polydisperse in terms of particle and bubble sizes. In this paper we study the impact of impeller design modifications on the hydrodynamics of a continuously overflowing bench-scale flotation tank. To this end, two different impeller designs, with and without a stator, were assessed using Positron Emission Particle Tracking (PEPT). This allowed the authors to determine, for the first time, the effect of an impeller design on the behaviour of both hydrophobic and hydrophilic particle tracers. It was experimentally observed that the use of a stator modifies the hydrodynamics within the flotation cell, distorting the lower mixing loop that is characteristic of axial impellers. The role of the stator in dissipating turbulence results in reduced particle velocities outside of the impeller-stator region. These results have important implications for flotation cell design and are discussed in the context of the impact that different designs have on particle movement, flotation hydrodynamics and, ultimately, flotation performance. The data set generated is also extremely valuable for modelling and validation purposes. Keywords: Flotation, flotation tank, impeller design, rotor, stator, PEPT, hydrodynamics

Jan 1, 2020

By S. C. Greeff

At ISCOR the quantitative determination of the structural properties of coke is done with a Leitz-TAS Image Analysis System. A reflected light microscopic image of a coke sample is converted into a binary image and stored in computer memory or on hard disc. By means of mathematical and stereological techniques the system can transform the images electronically. A lightpen can be used to determine the sequence of these operations. TASIC, which is based on BASIC language, is used as the program language on the computer. The majority of the programs are written by the user to ensure satisfactory results for specific studies. The computer controls the whole system, including the movement of the microscope stage, focusing, transformation and measurement of the image and data processing. The computer is also applied for establishing statistical correlations between the structural and other coke and coal parameters as well as for graphics and predictions of the coke structure. Factors affecting the structural properties of coke are discussed and conclusions are drawn.

Jan 1, 1987

By M. B. Díaz Aguado, I. Á. Fernández, C. González Nicieza, B. S. Menéndez

This paper summarizes the works that the Research “Group of Ground Engineering”, belonging to the Mining Department of the University of Oviedo, Spain, has been developing in close cooperation with the Regional Mining Department, since 2001, in order to control and monitor an experimental underground limestone exploitation by the room and pillars method. The aim of the current research is not only the geotechnical characterization of the rock mass (by means of laboratory and site tests) or the instrumentation of its displacements and stress changes (using convergence meters, INCREX probe, extensometers and rigid inclusion cells), but, moreover, to undertake intensive monitoring and control of such pilot mine, which is mined exclusively in order to accomplish this research. The data transmission was made on line via Internet, to achieve a full understanding of the behaviour of the experimental mine, to access data from remote locations and to visualize results from a website. All the collected information becomes input data for several numerical models using finite differences under a program developed in the research Group, ALMEC. The simulation and a final economical analysis lead to a design of an underground exploitation, at production scale, for a resource that is traditionally mined by means of open-pit process methods that could be worked underground with less environmental impact. The main purpose achieved by this exhaustive analysis is the technical and economic viability of such mine, for their optimisation for a future productive exploitation.

Jan 1, 2003

By Bosman

Medium suspensions play an integral part in the successful application of dense medium separation for both static and dynamic separators. Although models exist to predict particle movement as a function of medium density and viscosity, these models have been derived on the assumption of Newtonian rheology. Viscosity measurements of medium suspensions have shown that they are non-Newtonian, with a yield stress, and as such cannot be used in the existing models. As a result, medium selection remains an art based upon practical experience and indirect measurements of viscosity such as stability and cyclone differentials.

Jan 1, 2014

By S. Moodley

In the chloride process for TiO2 pigment production, various titania feedstocks (i.e. rutile, synthetic rutile, slag, and upgraded titania slag (UGS)) are chlorinated in a fluidized bed reactor with petroleum coke at temperatures between 1000°C and 1100ºC to yield gaseous metal chlorides. Although feedstock preference is largely based on TiO2 content, feedstock physical properties (i.e. density, sphericity, size distribution, and porosity) differ; these differences will affect fluidization behaviour and can inadvertently affect conversion efficiency. For example, a high carryover from the reactor reduces particle residence time and decreases conversion rates. Owing to dwindling rutile reserves in the world, most chloride producers are forced to feed blends of feedstocks to their chlorinators; and so it becomes important to understand whether blends have an effect on the hydrodynamic properties of the bed. This paper describes the physical characterization of different feeds and the determination of the elutriation constants for slag, rutile, synthetic rutile, and a blend (i.e. 50 wt% rutile, 50 wt% slag).A common feature of the tests was that particles finer than 75 µm tended more than any other size to be elutriated. The tested rutile, classified as a Geldart Group B material, had the lowest carryover, whereas the slags had the highest. Interestingly, the elutriation constant ([ki]) of the blend is lower than those of either of its individual components.

Jan 1, 2012

By V. Matou?ek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007

By B. van Beek, J. H. Zietsman, A. Lexmond, N. J. Andrew

"In platinum group metals (PGMs) smelting, the slag-to-matte ratios are very high (approximately 4:1 to 9:1). The slag temperature therefore has a strong influence on matte temperature, which is a continual concern due to the low matte melting temperature and its resultant high superheat. Maintaining a stable slag temperature is therefore a critical safety and operational issue. This project aims to improve the understanding of the slag bath temperature drivers so that a more effective slag bath temperature control strategy can be implemented.With the aim of developing a multiphysics model of the furnace, extensive data analysis was performed to develop an in-depth understanding of the process before the start of modelling work. In this work, the effect of fluctuating furnace feed composition on slag temperature was examined. The results are based on equilibrium calculations using FactSage, implemented with ChemApp.A method was developed, using an equilibrium calculation at 25°C, to convert the available chemical assays to approximate mineralogical assays in order to determine the feed enthalpies. Actual 2013 furnace feed data was used and the average specific energy requirement to produce slag and matte at 1600°C was calculated to be 671 kWh/t concentrate. The furnace energy input was then kept constant, and it was found that the slag temperature varies significantly as a function of the feed composition. These results were compared to actual slag temperatures measured on site. It was found that close management of the furnace energy balance is important for maintaining a stable slag temperature."

Jan 1, 2014

By J. Loubser

The concept of caring is in most cases confused with material needs and not psychological needs. By giving employees a job, most managers think that employees should be grateful and return the favour by being loyal, productive and working safely. Other managers hold the view that employees can be lucky to have a job. To show and demonstrate that management are caring for the safety of the workforce requires involvement, dedication and commitment. Obtaining the trust and respect of the workforce should be the main thrust of any organization because within trust and respect lie the secret of optimal safety performance. In the last 70 years, all the fatalities and serious injuries that occurred in the mining industry can be traced back to one thing, non-caring. The same safety non-compliances are still observed, reported and planned against as 70 years ago, and strange as it may sound, the same injuries occur the same way. The question could be asked: Does the mining industry need more risk assessments? More codes of conduct? More engineering. Or does the mining industry need more caring?

Jan 1, 2010

By S. Kahraman

The prediction of rock properties from indirect testing methods is important, particularly for preliminary investigations since indirect tests are easier and cheaper than the direct tests. In this study, we investigate the predictability of the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of rocks from the indentation hardness index (IHI) obtained using point load apparatus. Forty-six different rock types, 14 of which were igneous, 15 were metamorphic, and 17 were sedimentary were tested in the laboratory. The UCS and BTS values were correlated with the corresponding IHI values and the results were statistically analysed. The influence of rock classes on the relationships was also investigated. A strong correlation between UCS and IHI was found for all data. The correlation between BTS and IHI is not as strong as the correlation between UCS and IHI, However, it is in the acceptable limits. When the regression analyses were repeated for igneous, metamorphic, and sedimentary rocks, the correlation coefficients were generally increased. The results show the UCS and BTS can be estimated from IHI, In addition, the effect of rock classes on the relationships between IHI and both UCS and BTS is important.

Jan 1, 2012

By B. Gamble

Solid Energy's project evaluation process utilises a standard staged gate approach, with five levels leading ultimately to project execution (level 6). For a project to progress through each level, specific financial criteria need to be satisfied. Solid Energy primarily use value based (discounted cash flow) metrics to support investment decisions. Within this approach Solid Energy utilise a number risk-based techniques to quantify project uncertainty. This includes the use of risk-based probabilistic analysis using Monte Carlo simulation and probability-based scenario analysis. Figure 1 shows the net present value (NPV) cumulative probability. Project risks are identified through comprehensive risk workshops. The output of these workshops (list of key risks, ranges of uncertainty and probability of occurrence), is quantified within the financial models. Incorporating this risk information on a probabilistic basis allows an investment decision to be made with a robust knowledge of the range of possible project outcomes along with the likelihood (probability) of those outcomes occurring, for example 80 per cent confidence that the project value will be greater than NZ$10 M, 50 per cent confident it will be greater than NZ$50 M and ten per cent confident it will be greater than NZ$70 M. Incorporating risk implicitly into the financial analysis allows the business to easily evaluate/measure projects with different risk profiles. The detailed risk analysis does away with the complexity of arbitrary risk-based hurdle (discount) rates, as projects can be evaluated based on their specific risk characteristics. Whether a project will progress to the next level of investment and ultimately into implementation depends firstly on the value assessment in comparison with the associated risk/uncertainty, and secondly matching this with the businesses appetite for risk. At Solid Energy standard criteria are used for specific project evaluations, but in addition projects are considered on a portfolio or strategic basis also. Solid Energy attempts to maintain a mix of low risk (low value) projects with some high risk (high value) opportunities. The mix of projects must remain in line with the shareholders' risk appetite. One of the keys to a successful investment decision is ensuring that the appropriate information is available to decision-makers so that they may proceed with a comprehensive understanding of the risks and impacts associated with the decision.

Jan 1, 2007

By K. Forsberg, Ş. Kaya, C. Dittrich, M. Svärd, E. M. Peters

Scandium can be recovered from waste streams of other metallurgical processes such as red mud from the Bayer process and titanium dioxide acid waste. This is accomplished by an integrated process comprising leaching using acidic media, solvent extraction using organic solvents and stripping of Sc from the organic phase using NH4F solutions. The precipitation of scandium as (NH4)3ScF6 from NH4F strip liquors has been demonstrated at lab-scale with recoveries and purities greater than 98% and 98.3%, respectively. It is desired to assess the possibility of recovering the solvents for re-use in the process to improve its economy and environmental friendliness. Investigations have been conducted to recover alcohol by simple distillation from strip liquor-alcohol mixtures containing about 50 v/v% alcohol. The mixtures were obtained after anti-solvent precipitation of (NH4)3ScF6 using an alcohol to strip liquor volumetric ratio of 1:1. The starting strip liquor contained about 2000 mg/L scandium in 3 mol/L NH4F solution. In the recovery of methanol, the first distillate product collected had a purity of about 87 v/v% and this decreased slightly with time over two hours. The methanol distillate collected in the first 30 minutes with a purity of ca. 85 v/v% was re-used in anti-solvent crystallisation of (NH4)3ScF6 from the initial strip liquor, and the scandium recovery attained was about 98.6 w/w%, almost similar to that of 99.2 w/w% obtained using 100 v/v% methanol. For ethanol recovery, the first distillate product collected was approx. 84 v/v% pure and the distillate collected in the first 30 minutes with a purity of about 75 v/v% achieved a scandium recovery of about 97.2 w/w% in comparison to 98.5 w/w% obtained using 100 v/v% ethanol during anti-solvent crystallisation. Keywords: Alcohol recovery, methanol, ethanol, anti-solvent crystallisation, (NH4)3ScF6

Jan 1, 2020

By Z. Nzimande

The Constitution of the Republic of South Africa advocates the importance of sustainable economic development and justifiable environmental consciousness by business. The government needs to ensure that every citizen of the Republic has access to an environment that is protected, pollution free, and sustainable by enacting certain regulations. However, there are more than 5 700 derelict and unrehabilitated mines of all types in South Africa. Former asbestos operations were among the first to be targeted for clean-up under the programme instituted by the Department of Mineral Resources (DMR), owing to the proven direct impact of asbestos pollution on health. This paper seeks to investigate the challenges faced by the coal sector as far as mine rehabilitation and closure is concerned. For the purpose of this paper rehabilitation is defined as per the Chamber of Mines Rehabilitation Guidelines publication, which defines rehabilitation as putting the land impacted by mining activities back to a sustainable and usable condition. Some of the current rehabilitation challenges are technical skills (know-how), leadership focus, poor planning, cost saving initiatives, and the government's lack of capacity to enforcement rehabilitation requirements. It is imperative that mining companies identify rehabilitation as a critical strategic pillar that directly influences license to operate. The case study evidence indicates that relevant policies, appointment of accountable people, sufficient leadership support, and the correct choice of rehabilitation equipment can assist to improve the rehabilitation and land management challenge.

Jan 1, 2012

By J. Rowe

The attrition of activated carbon, and the loss of gold associated with it, is of significant economic importance to the operation of a CIP/CIL circuit The focus of this study was on activated carbon recovered from an elution circuit which was deemed too fine for reuse. Results of cyclosizer and laser particle size analysis identified that most of the carbon was contained in the larger size fraction suggesting formation by abrasion. Digestion and AAS analysis of the individual size fractions identified a disproportionate concentration of gold in the finer size fractions which was identified by scanning electron microscopy to be due to the presence of fine metallic gold formed as a result of the acid washing process. Attempts to strip the remaining gold using sodium hydroxide or sodium sulphide based solutions proved unsuccessful due to poor elution efficiencies and re adsorption of gold. Upgrading of the material by froth flotation was also investigated using various conventional flotation reagents which had some success in concentrating the free metallic gold, however, grade and/or recoveries were considered less than desirable. Greater success was ultimately found in the transfer of gold from the fine carbon material onto coarser virgin activated carbon using a caustic cyanide solution. Sodium sulphide, sodium chloride and ammonium chloride based solutions were also trialled but proved less successful owing to their inability to mobilise metallic gold or gold cyanide species. Repetition of the transfer process proved capable of stripping 97% of the gold contained on the carbon fines for abed volume ratio of 6:1.

Jan 1, 2009