Search Documents

By M. Tangstad, J. D. Steenkamp

In April 2013 a 48 MVA submerged arc furnace producing silicomanganese was excavated in South Africa. Since the high shell temperatures recorded in the tap-hole area resulted in the furnace being switched out for relining, the tap-hole area was excavated systematically. A refractory wear profile of the tap-hole area with affected hearth and sidewall refractory was obtained in elevation. The carbon ramming paste in front of, above, andbelow the tap-hole was worn, as was the SiC with which the tap-hole was built. A clay mushroom formed but was detached from the refractories. Thermodynamic and mass-transfer calculations were conducted to quantify the potential for wear by chemical reaction between refractory and slag and refractory and metal in the tap-hole area. It was found that chemical reaction between refractory and slag or metal could offer only a partial explanation for the wear observed; erosion is expected to contribute significantly to wear.

Jan 1, 2015

By W. Bendaikha, S. Larbi, A. Ramdane

An oolitic iron ore from Gara Djebilet, Algeria was characterized by X-ray diffraction, scanning electron microscopy, and energy dispersive spectrosopy and the phosphorus distribution between various phases studied. Two ore types were identified – a haematite-dominated, oolitic type and a more massive, magnetite-dominated type. The haematite-dominated ore had a higher phosphorus content, up to 0.6% in the iron oxide minerals, than the magnetite-dominated type (0.3% P). Owing to the very fine-grained texture of the gangue minerals, reducing the phosphorus content to levels suitable for steelmaking (below 0.05% P) by conventiobal means would entail an energyintensive process with a high carbon footprint. Preliminary leaching test work using a sulphurous geothermal water as lixiviant, assisted by solar thermal acceleration, gave very promising results, removing 0.13% of the residual P (or 21.7% removal of total P) from the high-phosphorus oolitic ore.

Mar 14, 2024

By S. Saeed, N. Coulson, P. F. Stewart

"The Mine, Health and Safety Act No. 29 of 1996, as amended, embodies worker self-regulation to advance health and safety in the workplace. An important provision for this is the Right to Refuse Dangerous Work (RRDW). This paper explores worker perspectives about the implementation of RRDW on South African mines against a backdrop of revised guidance in the sector: ‘Guideline for a Mandatory Code of Practice on the Right to Refuse Dangerous Work And Leave Dangerous Working Places’, gazetted in February 2016 by the Department of Mineral Resources (DMR). A mixed methods study conducted at mines (n = 14) included a survey of workers (n = 293), focus groups (n = 6) and in-depth interviews (n = 16). Workers reported a high level of awareness, a positive attitude, and experience of the formal RRDW. However constraints to the formal RRDW meant that informal worker resistance to dangerous work was commonplace. Evidence of informal non-confrontational consultation, cooperation, and collaboration in the event of a dangerous workplace also emerged between workers, and supervisors. The research underscores the importance of the RRDW and worker health and safety representatives to mine health and safety. The revised guidance addresses RRDW implementation gaps, but of concern is the potential partiality towards management interests. IntroductionEnsuring that mineworkers act on their duties and responsibilities for health and safety remains a concern across the globe. Article 13 of the International Labour Organization (ILO) Convention Safety and Health in Mines (176 of 1995) entrenched the Right to Refuse Dangerous Work (RRDW) as an important mechanism through which workers act in the best interests of their own occupational health and safety (OHS) and is considered a cornerstone of worker self-regulation (ILO, 1995). Countries ratifying Convention 176 are under obligation to make this right available to workers through OHS legislation that frames the circumstances, procedure, and protection of workers from discrimination in the event of a formal work refusal. The Convention has been ratified by 31 countries, with South Africa becoming a signatory in June 2000 (ILO, 2000). Worldwide studies show that workers use this right with caution (Hilgert, 2013) and cases associated with work refusal are rarely presented in court (Gunningham, 2007; Cooper, 2013). Rather, in cases of formal notification of a work refusal, issues arising out of this are addressed either in the immediate workplace or through the site OHS system and/or at industrial tribunals or similar mechanisms (Harcourt and Harcourt, 2000)."

Jan 1, 2018

By T. Feroze, B. Genc

"The effect of some of the system variables in forcing and exhausting ducted fan systems on ventilation in an empty heading was investigated using computational fluid dynamics(CFD) and comparative analyses. The diameter of the duct, duct mouth to face distance, and the power of the fan (quantity delivered by the fan) were varied and their effect on ventilation determined through a comparative analysis of the flow rates calculated close to the face of the heading. Estimation models were developed, which can be used to calculate the flow rate close to the face of the empty heading for different settings of the system variables studied.The study showed that recirculation for a forcing ducted fan system can be reduced by increasing the duct diameter or increasing the duct mouth to face distance. For the exhausting ducted fan system, higher flow rates were achieved by reducing the duct mouth to face distance, andincreasing the fan design flow rate and duct diameter.The outcomes of this investigation will help ventilation engineers in deciding the optimum duct fan system required for sufficient ventilation.IntroductionThe ventilation of underground mines, irrespective of the type of mine and mining method, is divided into two broad branches, the primary ventilation and secondary or auxiliary ventilation. The primary ventilation is responsible for the total volumetric flow through the mine and the auxiliary ventilation is responsible for the ventilation of the development ends, production areas, and facilities disconnected from the main circuit with no through-ventilation connections. Auxiliary ventilation is the more difficult to achieve (Bise, 1996), and the disruption of this ventilation system is considered to be one of the primary factors contributing to methane and coal dust explosions (Creedy, 1996). A number of causalities have been recorded by many authors due to these explosions (Phillips and Brandt, 1995; Dubinski et al., 2011; Phillips, 2015). The ventilation of short headings, less than 10 m in depth, can be carried out without the use of any auxiliary equipment (Feroze and Phillips, 2015). However, for headings deeper than 10 m, auxiliary ventilation systems are required. These are generally classified into the three basic types, namely line brattice (LB) ventilation systems, ducted fan systems, and jet fans (Figures 1 through Figure 3 respectively)."

Jan 1, 2017

By J. P. Gous, M. Tangstad, J. D. Steenkamp

In April of 2013 a 48 MVA submerged arc furnace producing silicomanganese was excavated in South Africa. One of the areas excavated systematically was the furnace taphole. The aim was to obtain a refractory wear profile of the tap-hole area, together with affected hearth and sidewall refractory. Subsequently, thermodynamic modelling was applied to quantify the potential for chemical reaction between refractory and slag and refractory and metal in the tap-hole area.

Jan 1, 2014

By K. Sasaki, S. Kuroiwa, H. Miki, Y. Aoki, T. Hirajima, Y. Orii, G. P. W. Suyantara

Selective flotation to separate copper minerals from, for example, Mo- and/or As-bearing minerals is a continuing problem because the selectivity of current systems is imperfect. Selective Cu-As flotation is currently difficult, and the most common Cu-Mo selective flotation method uses NaHS; this must be done in an enclosed system because, under acidic conditions, this method produces hydrogen sulfide. In this paper, some novel alternative flotation processes that use redox reactions are discussed; these methods have a much lower environmental impact. Oxidation and reduction reactions can be used to make copper minerals more hydrophilic and Mo-bearing minerals more hydrophobic. X-ray photoelectron spectroscopy (XPS) analyses indicated that the copper minerals became hydrophilic because hydrophilic iron precipitated and several hydroxides covered the copper minerals’ surfaces, whereas the molybdenum minerals remained hydrophobic because their sulfide surfaces were not covered. Flotation experiments on these minerals after redox treatments indicated that excellent separation of Cu-minerals from Mo-minerals can be achieved. Possible mechanisms for this separation were investigated using detailed surface analyses and thermodynamic calculations. The additives used to initiate the redox reactions are easy to handle and make these new flotation procedures better than current processes because the new methods do not emit effluent gas and because they are commercially viable. Keywords: Flotation; chalcopyrite; molybdenite; oxidation; reduction

Jan 1, 2020

By J. H. C. Pretorius, P. Nelwamondo

"Although South Africa possesses more than 80% of the world’s platinum reserves, its reputation for reliability in supplying platinum to global markets is under threat. This is due to the 49% decrease in output per worker (1999–2014), while the domestic costs have risen by more than 10% annually for the past 5 years. In addition, the continued decline in the commodity price by 38.3% (2012–2016) has resulted in a significant portion of the sector producing at a loss in 2015. The Chamber of Mines (now the Minerals Councilof South Africa) has suggested that solutions to improve productivity and reduce cost pressures are required. This research aims to provide operational excellence through the application of event chain project management (ECPM) to improve productivity and reduce operational costs. A case study was used to carry out research in platinum mines, with data collected using a motion-time study to measure the current efficiency of operations in each mining stope through actual activity durations. The results indicate that through the application of the event chain project management methodology, risks affecting the mining stope schedule can be managed, the efficiency of operations was improved by reducing the time spent on each activity, productivity was increased by shortening the project duration, and operational costs were reduced in the process. IntroductionSouth Africa’s total mining industry production was 4.9% lower in 2016 than in 2015; it decreased by 1.9% year-on-year in December 2016, with the main contributor to this negative trend being the platinum group metals (PGMs) with a drop of 15.1% and contributing -3.8% percentage points (Statistics South Africa, 2016). Although South Africa possesses more than 80% of the world’s platinum reserves, the 8% drop in production output since 2008 has put the platinum mining industry under the threat of being seen as an unreliable supplier to global markets. This decline in production is caused by the 49% decrease in output per worker between 1999 and 2014. In addition, the continued decline in the commodity price by 38.3% from 2012 to 2016 and an increase in operational costs during the same period resulted in a significant portion of the sector producing at a loss in 2015. A turnaround strategy is required to overcome these challenges. The Chamber of Mines has suggested, among others, the need for solutions to improve productivity and reduce cost pressures. The implementation of these solutions will ensure that the PGM industry thrives and reaches its potential of growing production to more than 322 t by 2020 (Baxter, 2016)."

Jan 1, 2018

By H. Mulder, M. C. Bekker

The principal objective of this investigation was to conduct a thorough literature review on the status of project readiness mechanisms, tools, techniques, and frameworks for mining projects. The review aimed at identifying common readiness evaluation criteria as well as potential shortcomings that prevent the establishment of a generalizable project readiness index. The literature review included a general overview of capital project performances and the importance of project readiness assessments to improve project delivery success. The study then progressed towards literature involving mining projects and how this differs from infrastructure and industrial project assessments. The paper concludes by summarizing the current state of mining project readiness assessments, the unique and differentiating factors to be considered, and suggests recommendations towards the development of generalizable readiness assessment criteria for mining projects.

Sep 1, 2022

By V. Yahorava

Efficient recovery of precious metals from process solutions is essential for improving process economics. Traditionally, precious metals are relatively effectively recovered from waste streams via precipitation or cementation. However, these approaches have a number of drawbacks, including poor water balance, creation of environmentally unfriendly waste streams, and losses of precious metals. Ion exchange technology is an alternative for the recovery of precious metals from waste or low-grade streams. This technology allows the recovery of the precious metals to extremely low levels (micrograms per litre) with relatively high upgrade ratios from the solution onto the resin without major water balance concerns, while the impact on the environment could be minimized or avoided. Research was conducted on the recovery of platinum group metals and gold from different low-grade and waste streams from one of the precious metals refineries in South Africa by means of ion exchange. Various functionalities and matrices (granular and fibrous) of ion exchange materials were evaluated. The results from these studies indicated that in some cases ion exchange could be very effective for the recovery of precious metals, and that the PGM concentration could be reduced to < 1 mg/L. The upgrading ratios of the various PGMs onto the specific fibres were relatively high for the specific streams evaluated, which might in some cases justify incineration of the loaded material instead of stripping and recycling the adsorbent. The cost of direct incineration for one of the waste streams tested would be less than 1% of the value of the PGMs recovered. However, the adsorbent has to be carefully selected and the process design optimized for each specific stream.

Jan 1, 2014

By G. Pienaar

The South African Institute of Mining and Metallurgy held a Colloquium on High-strength Low-alloy Steels on 27th October, 1983, at the Vaal Triangle Technikon, Vanderbijlpark. The Colloquium was attended by some 170 delegates.

Jan 1, 1984

By P. Altounyan, K. Akermann, T. Van den Berg

Amandelbult Mine is currently undertaking a trial to mechanise the mining of the UG2 reef through the introduction of room and pillar mining. As part of the trial, a system of managing the control of the hanging wall has been introduced, based on systems and technology that are proving successful in the nearby coal mining industry. The principal features are the use of a high bond strength, stiff bolting system which can be easily installed to a high standard, and a range of in situ tests and measurements to optimise the level of support installed to control the movement of the hanging wall. The rock bolt system and the measurements and tests described are new to the platinum mining industry. The paper describes these systems and their adaptation and application to hard rock mining. La Mine d’Amandelbult est actuellement dans des essais en vue de mécaniser l’extraction dans la veine UG2 grâce à l’introduction d’une exploitation par chambres et piliers. Dans le cadre de ces essais, un système de gestion de la paroi suspendue a été introduit, base sur des systèmes et une technologie qui prouvent donner de bons résultats dans l’industrie voisine d’extraction de la houille. Les caractéristiques principales sont l’utilisation d’un système de verrouillage raide et à forte adhérence qui peut être installé à un haut niveau de qualité et une gamme d’essais et de mesures in situ pour optimiser le niveau de soutien installé pour contrôler le mouvement de la paroi suspendue. Le système de verrouillage de la roche ainsi que les mesures et les essais décrits sont une nouveauté dans l’industrie minière du platine. La communication décrit ces systèmes ainsi que leur adaptation et leur application à l’exploitation minière en roche dure. Amandelbult Mine unternimmt gegenwärtig einen Test um den Abbau des UG2 Riffs durchEinführung des Kammerpfeilbau zu mechanisieren. Als Teil dieses Tests wurde ein System zur Kontrolle der Stollenfirstes eingeführt, welches auf jenen Systemen und Technologien basiert, diesich im nahe gelegenen Kohlebergbau als erfolgreich erwiesen. Die prinzipiellen Charakteristikasind der Gebrauch von einem steifen Bolzensytem mit hohem Verbundwiderstand die leicht zueinem hohen Standard gebracht werden können, und eine Reihe von in-situ Tests und Messungenum das Niveau der installierten Unterstützung zu optimieren, und um die Bewegung desStollenfirstes zu kontrollieren. Das Gesteinsbolzensystem, die Messungen und die Tests, diebeschrieben werden, sind neu in der Platinbergbauindustrie. Diese Arbeit beschreibt diese Systeme, deren Anpassung und Anwendung im Hartgesteinsbergbau.

Jan 1, 2003

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant, it was critical to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. Various compaction parameters were verified and established on a small laboratory-scale compaction machine to obtain a coal cake of acceptable stability. These parameters include cake density, cake surface moisture, transverse strength (force applied perpendicular to the original compacted coal cake layers), and applied force to the coal cake. This work determined the behavioural characteristics of the coal while being compacted either with a full-sized or a 1/3-sized compaction plate in a 9 kg capacity mould. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.The target wet cake density of 1 100 kg/m3 (79% of 1 400 kg/m3 relative density) was achieved for Waterberg sscc, with a particle size d50 varying between 0.6 mm and 1 mm, utilizing the 1/3-sized compaction plate in the laboratory-scale set-up, with 11.6% surface moisture and 92.2 t/m2 commercial equivalent applied force. For Oaky North hard coking coal, a wet cake density of 1 189 kg/m3 (85% of 1 400 kg/m3 relative density) was achieved at a surface moisture content of 12.3% and at a lower applied force than that for Waterberg sscc, i.e. 78.5 t/m2.Coal cakes of acceptable strength, and therefore sufficient stability for further processing, were obtained for all materials evaluated during this study.Further studies should be conducted to determine the effect of zeta potential during the compaction of coals.IntroductionExxaro Resources has successfully installed and commissioned a world-class stamp-charging horizontal 1 t electrically-heated pilot-scale coke oven at its Metallurgy Services facility. Prior to operating the coke non-recovery pilot plant, it is essential to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. The design of Exxaro’s pilot plant is such that the coal cake is pushed inside the oven by means of a pusher plate, rather than through a ‘spoon’ feed mechanism, such as is found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength during loading into the oven, owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability, various compaction parameters needed to be verified and established on a small laboratory-scale compaction machine."

Apr 1, 2019

By T. Bui, T. Wallmach, S. B. Blancher, A. Back, M. Pierre, V. Delarue, A. Kanzari

This study investigates nickel laterite porosity and its impact on geometallurgical modelling. We performed a detailed mineralogical study on a set of Ni-laterite samples originating from New Caledonia. Samples were analysed after heavy liquid separation by automated SEM (QEMSCAN®). Laboratory and QEMSCAN® modelling results do not correlate well. Ideal physical mineral properties such as mineral densities used in QEMSCAN® modelling do not match the actual physical densities of minerals. The presence of empty or water-filled pores can represent important amounts in minerals and change the overall density of a particle. An adequate modelling of real density separation of minerals and particles should consider the water-filled pores. The first step towards a better simulation was to integrate pores larger than 10 μm in diameter filled with water (density of 1 g/cm3) in the QEMSCAN® database. The results approached, but did not match the physical laboratory results. The second step was to identify nanometer to micrometer sized pores, which could not be identified by QEMSCAN®. It was possible to identify nanometric pores in enstatite, Fe-oxides, serpentine, talc and quartz, and radial aggregates of fibrous Fe-oxyhydroxides with high resolution SEM (HR-SEM). The quantification of those micro-sized pores was performed on 2D HR-SEM images using image-processing techniques developed in Python to calculate the nanometer to micrometer scale pores in each mineral. Despite the limitation of converting 2D imaging into 3D objects, in our case pore sizes and porosities, we were able to calculate a mean value of porosity for each mineral. The integration of this porosity in the calculation of particle densities yielded a good match between the QEMSCAN® model and the laboratory experiment results. Despite the complexity of a strongly weathered material, such as Ni-laterites, a good knowledge of the ore makes it possible to build reliable processing models. Keywords: Mineralogy, geometallurgy, nickel laterites, SEM, QEMSCAN®, porosity, density

Jan 1, 2020

By M. Fener, S. Kahraman, O. Gunaydin, M. Alber

Falling into the weak rocks category, fault breccias have extremely poor engineering properties. These pebbles typically cause issues with slopes, subterranean construction, and building projects. Professionals will benefit from the creation of some predictive models for fault breccia triaxial strength, as smooth specimen preparation is typically challenging and timeconsuming. The purpose of this study is to develop some predictive models for the differential stress (Δσ) based on physical and textural properties. Artificial neural networks were used to analyse data related to Misis fault breccia. Initially, models with moderate (noticeable, but not good) correlation coefficients were created using multiple regression analysis. After that, the regression models and three distinct artificial neuron network models were contrasted. Regression models are weaker and less trustworthy than artificial neuron network models, as demonstrated by this comparison. Pointed out is the practicality and ease of use of the artificial neuron network model with S-wave velocity and volumetric block proportion. Ultimately, it can be concluded that artificial neuron networks analysis provides a reliable indirect method for predicting the differential stress of Misis fault breccia.

Sep 1, 2025

By C. Musingwini

The South African mining industry continues to be a major source of employment at a time when at least 25 per cent of the working age population is unemployed. At the same time the industry faces a skills shortage in many of the disciplines necessary for its future health. The University of the Witwatersrand, University of Pretoria, University of Johannesburg, and University of South Africa have historically produced mining graduates for the South African industry, with any shortfall being met by the recruitment of overseas graduates. More recently the global shortage of engineers and other mining industry professionals has seen a reversal of this trend and a very significant emigration of well-educated and highly skilled personnel. The traditional career path for mining graduates is in production and mine management. However, there is the parallel and possibly more pressing need for specialized skills in such fields as ventilation, rock engineering, mine planning, mineral resource evaluation, and mineral asset valuation. It is in these essential areas that chronic shortages continue to hamper the development of the industry and may well frustrate its ambitions to be safe, healthy, and profitable into the future. The permeability of skills across sectorial boundaries within the mining industry requires that skills shortages in the platinum sector are not looked at in isolation, but within the context of the entire industry. This paper reviews the efforts being made by the universities at both undergraduate and postgraduate levels to meet the needs of the South African mining industry, in terms of the required numbers and the range of specialized skills.

Jan 1, 2012

By P. L. Ngwenyama, I. Maubane

Soundless chemical demolition agents (SCDAs) are proving to be the future of sustainable and environmental-friendly mining. These expansive chemicals become critical when there is a need to break rock close to communities, environmentally sensitive areas, and critical structures and infrastructure. Unlike explosives, the SCDAs do not generate air-blast, ground vibrations, flyrock, noise, dust, and noxious fumes, which can negatively affect the environment, surrounding communities, sensitive areas, and critical structures and infrastructure. Over the years, several types of SCDA products have been used successfully in the civil and construction industries for the demolition of old and dilapidated buildings near vibrations and environmentally sensitive areas. They have also been used to fragment boulders in the mining and construction industries. However, to date, no study has investigated the applications of soundless chemical demolition on a large-scale in opencast mines. Therefore, this study evaluated whether soundless chemical demolition can break large volumes of in situ rock. This was done by conducting five trials using Nex-Pand soundless chemical demolition agents in four different surface mining sites. Trial 1 was unsuccessful as it was unable to break the rock due to the large confinement between the drilled holes and the use of a hole diameter that was 182% larger than recommended. Trial 2 was a success as it was able to fracture the rock with a crack width that reached 110 mm after 72 hours. Trial 3 generated cracks at the biggest hole diameter of 102 mm. The cracks developed and ceased to increase after 96 hours at a crack width of 100 mm. Trial 4 achieved the smallest crack width due to a very competent rock compared to the other sites. Trial 5 generated cracks at a slower rate than other trials because of the use of Nex-Pand powder at lower ambient temperatures than recommended. These trials proved that soundless chemical demolition agents can replace explosives in areas closer to sensitive infrastructure and communities. This will ultimately enable mines to unlock value and access deposits in these areas.

Jul 23, 2025

By A. M. Garbers-Craig, T. Coetsee, T. M. Nemavhola

Accretions often form in furnaces when slag and charge materials attach to the refractory wall and build up over time. Accretion formation is usually unwanted because it reduces the working volume of the reactor and hinders material flow through the reactor. However, in some instances a thin, stable accretion layer may be desirable to protect the underlying refractory material. In order to prevent and/or manage accretion formation, it is important to understand the underlying principles of this phenomenon in the particular reactor. Excessive accretion formation hampered production at the Exxaro FerroAlloys ferrosilicon melting and atomization plant. This plant uses induction furnaces in which a 15% silicon-iron alloy is produced by batch smelting a mixture of ferrosilicon of 75%Si grade and low-carbon steel. The molten ferrosilicon alloy is then gas-atomized to a powdered product for use as a dense medium in mineral processing plants. The objective of this study was to investigate the effect of different impurity levels in the ferrosilicon feed material on the extent of accretion formation as well as the effect on the accretion properties, which influence the ease of accretion removal upon furnace shut-down. Refractory and accretion samples were collected after a furnace shut-down and characterized using X-ray diffraction and scanning electron microscopy–energy dispersive spectroscopy. It was concluded that the trace elements in the FeSi-75 feed material (Al, Ca, Mn) were mostly responsible for accretion formation, but that rust on the low-carbon steel and oxidation of the steel contributed to accretion attachment to the lining. The total contaminant content, calcium to aluminium ratio in the FeSi-75 feed material, and thereby the liquid to solids ratio in the accretion at temperature determine the strength of attachment as well as growth of the accretion.

Feb 2, 2021

By M. Louarrat, G. Enaime, A. Yaacoubi, A. Baçaoui, J. Blin

"The purpose of this study is to prepare a new activated carbon from olive stones for use in gold recovery by carbon-in-leach (CIL) and carbon-inpulp (CIP). The preparation method chosen was physical activation using steam. The effect of four process parameters: the residence time for carbonization, the activation temperature, the residence time for activation, and steam flow, were studied by the mean of response surface method (RSM) in order to optimize the yield, iodine index, and attrition characteristics. These two last responses were used as primary indicators of gold recovery capacity and mechanical strength. The results obtained show that optimal activated carbon can be prepared under the following conditions: a carbonization time of 157 minutes, activation at 921°C for 53 minutes, and a water vapour flow of 0.18 mL/min. This optimum carbon has an iodine value greater than 1100 mg/g and an attrition index in the order of 0.74%. These values reflect the quality of the precursor (olive stones) as a raw material for the development of an effective new activated carbon for the gold mining industry. IntroductionActivated carbon is an effective adsorbent widely used in industry due to its high surface area, well-developed reproducible microporous structure, and high degree of surface reactivity and adsorption capacity. World consumption of activated carbon is steadily increasing. It is primarily used in industrial wastewater and gas treatment and also for silver and gold recovery from cyanide solutions (Syna and Valix, 2003; Soleimani and Kaghazchi, 2008; Buah and Williams, 2010; Eddy et al., 2011). However, activated carbon is expensive and it needs to be regenerated after each adsorption cycle. In order to decrease the cost of manufacturing activated carbon, low-cost forest and agricultural wastes are considered promising new materials. In recent years considerable research has been reported on activated carbon from agricultural wastes, such as olive stones (Yavu et al., 2010), acorn shells (Sahin and Saka, 2013), peanut shells (Wu, Guo, and Fu, 2013), grape seeds (Jimenez-Cordero, 2014), coconut shells (Yalcin and Arol, 2002; Gratuito, 2008), palm shells (Sumathi, 2009), cherry stones (Jaramilloa, Gomez-Serrano, and A´lvareza, 2009), macadamia nut shells (Eddy, 2011), apricot stones (Soleimani and Kaghazchi, 2008), and bagass (Syna and Valix, 2003)."

Mar 1, 2019

Mining executives often have a difficult task determining what the strategic objective of the business should be as this can be impacted by the prevailing market conditions. In addition, they have no mechanism to quantitatively &apos;test&apos; the impact of this strategic decision on the business and understand the underlying dynamics. During the commodities bull run of 2003 to 2008 the strategic objective may have been to grow the long term value of the business (NPV) through increased tonnage, acquisition and finding new reserves, which all came with an increasing fixed cost base. Now with the financial crisis upon us and the collapse of commodity prices and demand, executives have adjusted their strategies as &apos;cash is king&apos; and short-term cash flow, in some instances at the expense of long terms value, is the order of the day. For many mining companies, mine closures, reductions in production and cost cutting exercisers are now the focus. In many instances, management do not have an ability to rapidly test different strategic alternatives to &apos;test&apos; the impact on value, unit costs, reserves and profitability at the operational level and optimize the underlying trade-off variables. Economic modelling of the complete business value chain is a means of linking the operational &apos;reality&apos; and strategic choices, so that the full impact can be assessed. This paper describes some of the challenges facing mining executives and how economic modelling can be applied to make decision making more rigorous.

Jan 1, 2010

By G. D. Rosales, P. F. A. Braga, S. C. A. França, C. P. Pinto

The growing market demand for lithium is mainly due to its use in the manufacture of batteries for electric or hybrid vehicles and portable equipment (smartphones, tablets, power tools, notebooks, etc.). Currently there is great interest in finding new sources of lithium and technologies for its utilisation. Li-S batteries have received attention due to their theoretically high specific energy density, which is 3 to 5 times greater than that of Li-ion batteries. Unlike Li-ion batteries, of which the main raw materials are lithium carbonate and lithium hydroxide, the main raw material for Li-S batteries is lithium chloride. The anode used in Li-S batteries is metallic lithium, produced by a molten lithium chloride electrolysis process. The extraction of lithium from pegmatites such as spodumene, previously abandoned in the 1990s for being uneconomical, has become attractive due to the increase in prices as well as the need for greater lithium purity of products made from lithium-bearing minerals. The main methods used for lithium recovery from spodumene ore include the sulfuric acid process, the alkaline process (lime or limestone as raw material) and the chlorination roasting process. Thermodynamic modelling using HSC software 5.1 was conducted to predict different reactions that could occur during chlorination roasting of the spodumene/MgCl2+CaCl2 system. Lithium extraction from the solid obtained after the chlorination roasting was also investigated. The results of thermodynamic analysis provided a better understanding of the chlorination roasting process for lithium extraction. Metallurgical tests with a mass ratio of 1:6 (spodumene:chlorides) and molar ratio of 2:1 (MgCl2:CaCl2) allowed over 95% recovery of the lithium contained in the spodumene concentrate. Keywords: Spodumene, lithium chloride, chlorination roasting

Jan 1, 2020