Search Documents

By Piyush K. Dutta

This report describes the design, development, manufacture and incorporation of noise control features on a jumbo drill and the results of successful tests of this drill in surface and underground mines. The noise-reducing features developed under this program are applicable to future designs of jumbo mounted drills that can be cost effectively manufactured and have the potential to reduce noise levels at the operator's position from 115-120 dBA to 95 dBA or less without a reduction of currently attainable drilling rates.

Jan 1, 1985

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and maintenance costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per elm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured underground. The computer outputs for each simulation run are presented in Volume II of this report.

Jan 1, 1983

By Sanford J. Douglas

This publication describes a study by the Federal Bureau of Mines of devices and methods used for testing and splicing 4,160-volt and 440-volt cables and for providing ground-fault protection for 440-volt circuits, as developed and used by the electrical staff of the Tecumseh coal mine, an open-pit operation at Boonville, Ind. The testing and ground-fault devices described should find ready application in other open-pit mines, and, with suitable modifications for voltages involved, in underground mining. The devices and testing methods are based on sound engineering principles and are time-tested and economically feasible, Four devices are used: A high-voltage tester, and a low-voltage high- current tester, both for testing 4,160-volt cables; a tester for 440-volt cables; and, electronic ground-fault protective device for 440-volt cable circuits. All the cable testers and the grounding device were designed and built at the mine from standard parts. They are inexpensive, dependable, and job tested, An attempt has been made here to describe them in enough detail so that interested persons can assemble duplicate units.

Jan 1, 1960

Productivity in underground metal and nonmetal mines is contingent upon work methods, mine layout, and ore handling techniques. One of the most important factors impacting productivity is the efficient movement of men, materials and supplies from the surface into and throughout the mine. Various transportation systems such as man-trains, service shafts, rubber-tired diesel equipment, etc. are currently used to transport men and supplies in underground mines. In many underground mines, it is not uncommon for a worker to spend 25% of his eight-hour working day traveling from the surface to his work area and returning to the surface.

Jan 1, 1975

By J. D. Dixon

This Bureau of Mines report describes a technique for determining the confining pressures that must be provided for stabilizing underground openings in incompetent rock. The technique is adapted for use with a nonlinear finite-element computer code, NONSAP, to obtain stabilization pressures for linear or nonlinear stress distributions in the rock media around the excavation. This analysis permits a point-wise calculation of active rock pressures that depend on the values of shear stress and strength along the excavation surface. The approach is applied to the solution of several sample problems. The results show that both the magnitude and the distribution of stabilizing confining pressures are significantly influenced by rock and joint strengths, joint orientation, and biaxial nature of the load field.

Jan 1, 1976

By Maria I. De Rosa

Analysis of mining equipment fires from 1990 through 1999 reveals that there were 340 large mining equipment fires, resulting in 72 injuries and five fatalities. Many of the fires resulted in the loss of equipment and all posed potential or real risks to the operator. In 97 cases, the fires raged out of control due to engine shut­off failure, even upon activation of the machine fire suppression system, due to the spraying of pressurized hydraulic flu­id and fuel onto hot engine surfaces. In other cases, even after engine shutoff, the fires re-ignited, fueled by the contin­ued flow of flammable fluids remaining in the lines onto the hot engine surfaces. In many of the fires, flammable vapors evolved and penetrated the cab, violently igniting, forcing the operator to exit under very hazardous conditions. The use of emergency evacuation lines in the fuel and hydraulic fluid systems, and methods to reduce or prevent the spraying of pressurized fluids onto hot engine surfaces would greatly improve the chances of successfully suppressing large mining equipment fires. In addition, the use of systems for preventing the ignition of flammable vapors inside the cab, and detecting and suppressing fires originat­ing in the cab, would greatly enhance operator safety. The National Institute for Occupation Safety and Health (NIOSH) recently conducted experiments on meth­ods to reduce the fire hazards associated with large mining equipment. These experiments evaluated the use of cab inerting systems to prevent the ignition of flammable vapors inside the cab and sup­press fires originating in the cab, while maintaining a breathable atmosphere for the operator to bring the equipment to a stop and safely exit the cab.

Jan 1, 2008

By Wilbert J. Huff

For the past 9 years , the technical studies conducted by the Explosives Division of this Bureau have been summarized in a series of reports issued annually . The following account presents investigations undertaken from July 1 , 1943 , to June 30 , 1944. The work is detailed under a number of main headings corresponding to the organizational structure of the Division , the various activities being under the immediate direction of unit chiefs , who report directly to the author . Specific credit , however , is due to the individual unit leader and his assistants .

Jan 1, 1945

By M. L. Bowser

Pulse-forming circuitry is described for use in explosives research that requires precise synchronization and control of events in order to investigate detonation parameters. Included are pulse generators for oscilloscope sweep control, counterchronograph actuators, and a raster-type oscillographic method for the determination of velocities of detonation that are applicable to studies on solid, liquid, and gaseous detonations. INTRODUCTION Prom time to time, requests have been received for information on electronic circuitry used in explosives work at the Explosives Research Laboratory, Bruceton, Pa. The methods used are not entirely original;4 5 6 however, modifications of earlier techniques and some novel design aspects have resulted in time-tested methods that warrant a more detailed description.

Jan 1, 1962

By Loren R. Anderson

Traditionally, an evaluation of the safety of slopes has been based on computing a safety factor against failure. In computing the safety factor, the geometry of the slope, the soil parameters and the pore pressures are treated as deterministic quantities even though they are known to be random variables. A pseudo-three-dimensional probabilistic slope stability model has been developed that treats shear strength as a random variable. The model uses the probability of a slope failure as an assessment of slope reliability. The model can accommodate zoned embankments of soil in which the strength is described by the Mohr-Coulomb strength envelope. Autocorrelation functions are used to describe the spatial correlation of the strength parameters, c and tan ø. Model error can also be included in the analysis. The model has been applied to an existing tailings dam and to several hypothetical examples. These examples are presented to illustrate the influence of the choice of the soil strength variability parameters on the probability of failure. The results show that the critical failure surface based on the minimum safety factor is not necessarily the failure surface that will yield the maximum probability of failure. The analysis of the tailings dam shows that variance reduction can be large and that the model error is the dominant source of uncertainty for the embankment analyzed.

Jan 1, 1982

By Dana C. Reinke

Jan 1, 2005

The purpose of this report is to describe the work accomplished by Mine Safety Appliances Company under Contract No. H0110845. This contract required the design, installation and testing of a permissible mine surveillance and communication system for the USBM Bruceton experimental mine facility. While much of the design and operational detail of this system can be drawn from the instruction manuals delivered with the equipment, some of it will be repeated here in Volume I for the sake of clarity, but the principal objective will be to report on overall system and subsystem performance and to suggest design alternatives for future consideration. Details of the overall system design will be found in Volume II of this report.

Jan 1, 1973

By William C. Cooley

A technical and economic study was made of the feasibility of establishing an underground hydraulic coal mine in the Wilkeson-Carbonado coal field approximately 25 miles southeast of Tacoma, Washington. The deposit contains reserves of more than 200 million tons of generally high quality metallurgical coal. It is located in nine seams of minable thickness in a complex, folded and tectonically disturbed set of anticlines and synclines. Typical dip angles are up to 60°, with minable seam thicknesses of 6 to 17 feet. A mine plan was made for a 2 million TPY mine (clean) using two shafts to access the deposit to a depth of 2500 ft. The mining method uses monitor jets to break coal by sublevel retreat mining, fluming to a sump and pumping the minus 0.25 inch coal to the surface and to a preparation plant. The plus 0.25 inch coal is hoisted by skip. Cleaned met coal would be shipped by rail for export. A middlings product would be sold as thermal coal. Assuming a coal price of $48 per short ton (FOB the mine) for the met coal and $35 for the middlings, the return on investment is estimated at 20% after taxes. The many uncertainties about the geological conditions and the specific mine design parameters make the economic analysis and conclusions somewhat tentative. A second mine could also be developed in the eastern section of the reserves to produce 1 million TPY of clean coal and is expected to have similar economics. Recommendations are made for a Test Mine and a Pilot Mine leading to a production mine.

Jan 1, 1983

By Thomas Novak, Jeffrey L. Kohler, Joseph Sottile, Steve J. Gnapragasam

Modern underground coal mines can be very large, having a total connected load in excess of l5 000 hp. These mines generally have many miles of high-power conveyor belts and 15 or more miles of high-voltage power cables at distribution voltages of 12.47, 13.2, 13.8, or 14.4 kV. The shielded cables used in mine power distribution systems have a significant level of capacitance, on the order of 110 pF/ft. This level of capacitance, in an extensive power distribution system at today's voltage levels, can cause significant charging currents during a ground fault. This paper addresses the potential detrimental effects of capacitance charging currents during line-to-ground faults in mine power distribution systems. A representative mine power system is modeled, and simulations with faults at various locations are conducted to evaluate the effects of this capacitance on the level of fault current and relay selectivity. This paper also includes results of capacitance measurements made on mine power feeder cables used to validate the simulation model.

By D. E. Kirby

In line with the Bureau of Mines' goal of providing technology to maintain a supply of minerals adequate to meet national economic and strategic needs, a method for recovering chromite from lateritic materials was investigated. Laterites are a large resource of Ni, Co, and Cr, critical metals of which the United States has insufficient domestic sources. A roast-leach method was developed by the Bureau to extract nickel and cobalt from domestic laterites. A concurrent effort was made to recover chromium from either unprocessed laterites or the leach residues. This report characterizes laterites and laterite leach residues. It describes a chromite recovery procedure using conventional industrial beneficiation equipment for sizing, low-intensity magnetic separation, and gravity concentration. Concentrates containing 20.0 to 22.4 pct Cr (29.0 to 32.7 pct Cr203) and with a 1.6:1 to 1.9:1 Cr-Fe ratio were recovered from laterites and residues containing 1.3 to 2.5 pct Cr with recoveries exceeding 50 pct. Because of their low grade and fine size, these concentrates would be suitable for preparing chromium chemicals. The direct beneficiation of laterites for chromite recovery resulted in the minerals containing nickel and cobalt concentrating in slime products. No iron oxide coproducts of acceptable grade were recovered from either laterites or residues.

Jan 1, 1982

By S. R. Crane

One Bureau of Mines goal is to minimize the undesirable environmental impacts associated with industrial plants emitting waste gases containing S02. To help meet this goal, a regenerable flue gas desulfurization process was developed. This process, known as the citrate process, uses a buffered weak acid solution to absorb S02 from the waste gas. The absorbed S02 is reacted with H2S to precipitate elemental sulfur and regenerate the solution for recycle. The H2S feedstock for the process, if not otherwise available, may be produced by reacting two-thirds of the recovered elemental sulfur with natural gas and steam. Laboratory investigations and pilot plant operations were conducted by the Bureau to determine if H2S from the natural gas, sulfur, and steam reaction was suitable for the citrate process. The laboratory investigations, in which an H2S generator was integrated with other citrate process operations, provided a basis for design and operation of the pilot plant. The objective of the pilot plant was primarily to provide H2S for the citrate pro-cess pilot plant at the Bunker Hill Co. lead smelter in Kellogg, Idaho. The design capacity of the pilot plant was 0.4 to 1.25 tons of H2S per day. The operation demonstrated that (1) a 77-to 79-dry-volume-percent H2S product could be produced from pilot-plant product sulfur, natural gas, and steam; (2) the product R2S regenerated the SO2-loaded citrate solution; and (3) under certain conditions over 95 percent of the natural gas could be converted to H2S.

Jan 1, 1981

This report includes a short history of uranium and its uses, mineralogy of common uranium minerals, and information on the use of electronic prospecting equipment and tests for detecting the presence of uranium. Details are given on geologically favorable areas and formations and practical methods of prospecting. Some information is given on the staking of claims, what lands are open to prospecting, and methods of securing mining rights. A forecast of the economic outlook for uranium is included. Appendixes give sources of additional information and a list of libraries where unclassified Atomic Energy Commission reports may be consulted. Because the increasing use of uranium by industry has revived interest in prospecting and exploration for this element, the Bureau of Mines has issued this report, which brings up to date and expands the subject matter of a hand- book on uranium exploration and production published in 1956.l

Jan 1, 1968

A mineral survey of the Rough Hills WSA (Wilderness Study Area) in northeastern Nevada was done by the U.S. Bureau of Mines in 1985 at the request of the Bureau of Land Management. The WSA is comprised of 6,685 acres of mountainous, desert lands within the Elko District of the Bureau of Land Management. The survey entailed investigations of prospects or mineral occurrences to provide information on possible resources within the WSA. No mineral resources were identified in the WSA. The only historical mining activity was for placer gold at the Prunty prospect at the confluence of Copper Creek and the Bruneau River. Total gravel at the prospect is about 6,500 cubic yards; however, the survey showed significant gold values (greater than $0.10 gold per cubic yard) only in the southwestern portion. There, however, the gravel averaged less than $1.00 gold per cubic yard, and only about 3,000 cubic yards are present, a grade and yardage insufficient to be of commercial interest. The occurrence, however, may have value for recreational mining by hobbyists.

Jan 1, 1986

By C. E. Hennig

On January 1, 1961 there were 311 petroleum refineries in the United States with a total crude-oil throughput capacity of slightly more than 10 million barrels per day, according to the Bureau of Mines' annual survey. Compared with a year ago, this represents net increases of one in the number of plants and 109 thousand barrels per day in total capacity. Contributing to this increase was the completion of two new plants, one in Hawaii and another in Michigan, during the year. At the beginning of 1961 the industry was building facilities which will increase this overall crude capacity by 36,500 barrels per day. As part of its building program, it was also replacing 329,000 barrels per day of its present capacity. Of the total 10 million barrel per day installed capacity, the industry reported 380,000 barrels per day as being shut-down on January 1, 1961. This included 11,500 barrels per day considered inoperable without extensive reconditioning.

Jan 1, 1961

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By Martin H. Stanczyk

Bench scale, laboratory batch attrition grinding tests were made of a coarse commercial kaolin in a stainless steel, 5-inch-diameter attrition grinding machine to study the effect of a number of basic operating variables on particle size reduction and electric energy consumption. The results of the investigation showed that the more important operating variables influencing the efficiency of kaolin comminution and energy consumption requirements were type, size, and shape of grinding media, grinding media to clay weight ratio, peripheral rotor speed, clay slip pulp density, degree of pulp dispersion, and the angular arrangement of the rotor and stator bars. The tests also indicated that variables having less influence on grinding efficiency and energy consumption were pulp temperature, design of rotor cage, rotor clearance, rotor-stator bar interval, addition agents, pulp level, degree of pulp aeration, and chamber liners. The research showed that grinding media had the greatest influence on abrasion of machine parts and that spherical-shaped grinding media were superior to sharp angular or long bladed media with respect to media degradation, machine abrasion as well as grinding efficiency.

Jan 1, 1968