Search Documents

By D. Randolph Berry

Volume II contains appendices which explain and document the recommendations of Volume I. The following topics are covered: Appendix A Discussion of Recommended Guidelines Appendix B Worldwide Use of Oxygen Self-Rescuers Appendix C Hypothetical Use of Oxygen Self-Rescuers in Post-1972 Coal Mine Explosions and Fires Appendix D Vibration Testing of SCSRs Appendix E Testing of In-Service Chemical Oxygen SCSRs Appendix F Discussions with Representatives of Underground Coal Mining Appendix G Recommendations for SCSR Storage Containers Appendix H Example SCSR Storage Plans Appendix I Testing of In-Service Compressed Oxygen SCSRs Appendix J 30 CFR 75.1714, 30 Regulations Pertaining to Self-Rescuers

Jan 1, 1981

By S. L. Gerhard

In the United States the performance characteristics of permissible explosives are controlled by routine tests, which include firing the explosive into a gallery filled with a methane-air mixture. These tests are made by the staff-of the Explosives Division of the Bureau of Mines and are similar, in general, to those employed in other countries. This control has helped to reduce the frequency of accidents involving the ignition of firedamp by explosives but has not clarified the basic causes of the ignition. To advance this control and to minimize potential hazards further, this fundamental knowledge is needed. Some of the results of recent research on the causes of the ignition are described herein. NATURE OF THE PROBLEM When an explosive ignites firedamp in the gallery tests, the source of the ignition must be one or more of the emissions from the steel borehole. It has been accepted generally that these emissions are (1) particles, (2) the shock wave, and (3) hot gases and flames. Photographs show that the shock wave emerges from the borehole first, followed closely by hot gases. At first the velocities of these are high and approximately equal, but the velocity of the gases decreases more rapidly than that of the shock wave, and by the time the reactions causing the flame are complete the shock wave travels in an otherwise undisturbed medium. The particles are originally enveloped in the hot gases but some soon begin to break through and eventually out-distance the shock wave. The approximate geometry of these emissions about 1 millisecond after the shot is fired is illustrated in figure

Jan 1, 1939

By Y. P. Chugh

This is the final report of a study done by IIT Research Institute for the Bureau of Mines to identify the problem areas and technological inadequacies in noncoal (metal, nonmetal, stone, and sand and gravel) mining and processing systems that are the primary causes of death, injury and occupational disease, and to make recommendations to improve safety and health in these operations. The findings and recommendations presented in the report are based on: (1) analyses of MESA injury and employment data for the period 1961-70, MESA fatality reports for underground noncoal mines (1968-72) and lost time accident data for 1970-72 obtained from mining and processing operation: (2) visits to a variety of noncoa1 mines and mills throughout the country to observe the operations and to study the safety organization and practices used in the industry and (3) interviews with industry and government representatives knowledgeable in the field of noncoa1 mining and processing safety and health. The report provides a comprehensive overview of safety and health problems.

Jan 1, 1974

By S. L. Gerhard

In the United States the performance characteristics of permissible explosives are controlled by routine tests, which include firing the explosive into a gallery filled with a methane-air mixture. These tests are made by the staff of the Explosives Division of the Bureau of Mines and, are similar, in general, to those employed in other countries. This control has helped to reduce the frequency of accidents involving the ignition of firedamp by explosives but has not clarified the basic causes, of the ignition. To advance this control and to minimize potential hazards further, this fundamental knowledge is needed. Some of the results of recent research on the causes of the ignition are described herein. NATURE OF THE PROBLEM When an explosive ignites firedamp in the gallery tests, the source of the ignition must be one or more of the emissions from the steel borehole. It has been accepted generally that these emissions are (1) particles, (2) the shock wave, and (3) hot gases and flames. Photographs show that the shock wave emerges from the borehole first, followed closely by hot gases. At first the velocities of these are high and approximately equal, but the velocity of the gases decreases more' rapidly than that of the shock wave, and by the time the reactions causing the flame are complete the shock wave travels in an otherwise undisturbed medium. The particles are originally enveloped in the hot gases but some soon begin to break through and eventually out-distance the shock wave. The approximate geometry of these emissions about I millisecond after the shpt is fired is illustrated in figure

Jan 1, 1939

By Thomas E. Finch

This report is an engineering-economic evaluation of alternate methods of handling the parting between two coal seams. It consists of evaluations of parting stowing techniques applicable in a representative, thick seam western United States mine. Methods are examined for their potential implementation, and an estimated operating cost per yard of material moved is developed. The methods are of two categories castback or haulback. Haulback methods use truck haulage except With scrapers, and the castback methods are a direct stowage with no intermediate haulage equipment. Possible equipment combinations include draglines, shovels, hydraulic backhoes, bucket wheel excavators, scrapers, and front end loaders. The purpose of this report is to evaluate the effective competetiveness of the various alternatives.

Jan 1, 1975

By R. Stefanko

This first Annual Report covers the work on Contract No. H0377043 "Cable for Face Equipment", from August 1, 1977 to July 31, 1978. It reports the progress in the three areas of over-and short-circuit protection, cable ampacity research and cable couplers. Field trips have established many interesting facts related to circuit breaker settings and cable size. For example, the determination of cable sizes depends on the RMS duty cycle current determined by a particular piece of equipment, but the actual selection of the cable to be used is often a function of the maximum allowable circuit breaker instantaneous settings as specified in Title 30. In order to avoid nuisance tripping as a result of instantaneous starting current field, laboratory and analytical studies are being conducted to determine proper settings and cable sizes Also an extensive program has been established to monitor the performance of high voltage cable couplers and determine their modes of failure. Various equipments are being designed for laboratory testing, and an extensive reeled cable experiment is also under way.

Jan 1, 1978

The NIOSH suite of coal mine ground control software addresses nearly every aspect of coal mine ground control planning, including geologic characterization, mine layout, pillar design, and support selection. Mine planners who use the soft-ware have access to the knowledge gained during years of NIOSH research—packaged in a simple, easy-to-use format. Several of these software packages have recently been updated and improved. Analysis of Roof Bolt Systems (ARBS) (Figure 1) helps select the proper roof bolt system design from the immense variety of available bolt types and patterns. It was developed from statistical analysis of extensive bolt performance and roof fall data. New features in Version 2 include— • The capability to analyze roof bolt systems that use two types of bolts; and • A roof support cost module that estimates the total in-stalled cost of different patterns, considering the costs of consumables, labor, maintenance, and other factors. The Support Technology Optimization Program (STOP) (Figure 2) can be used to make judgments regarding which secondary support system will be the most effective in a particular mine condition and to evaluate the advantages or dis-advantages of alternative support systems. Version 3.0 includes additional improvements: • Supports with large load-shedding following yielding can be designed based on the peak loading capability as well as the residual loading capability; • Seven new support systems have been added to the program; and • Easier access to photo gallery has been provided. The Coal Mine Roof Rating (CMRR) replaces com-plicated geologic information with a simple numerical rating that mine planners can use in many ground control applications. The CMRR can be readily integrated into a geologic exploration program, and the software package is capable of generating an AutoCAD CMRR "layer." Version 1.2 contains— • The complete CMRR database with more than 250 ratings obtained from 70 different U.S. coal seams; and • An all-new "Help" file that clearly explains all aspects of the program. Analysis of Horizontal Stress in Mining (AHSM) can help find the optimum mine layouts for control of horizontal stress. It can be used to analyze both development and longwall retreat designs, and it shows how the stress condition varies as the entry, crosscut, and panel orientations are changed. Version 2 features— • Improved graphics that enable the user to observe the effect of design changes without adjusting the display on the computer screen; and • Resource files containing information on stress map-ping, advance-and-relieve mining, stress measurements in U.S. coal mines, and other topics. [ ]

Jan 4, 2006

By Elaine T. Cullen

Human beings are natural storytellers and story listeners. We learn very early that stories entertain us, but also give us the ?rules? about what is expected of us and how to make meaning of our experiences. Stories are integral to our lives, and have great power to change or influence how we think or how we react. They are an innate part of how we learn, and have obvious benefits to trainers or educators who are trying to impact what and how we learn. This paper and presentation discuss the social and cultural power of stories, and how they have been used to develop training for skilled blue-collar workers. Included will be examples as well as suggestions for trainers on where to find stories, what type of stories to pay attention to, and how to use them to improve occupational safety training.

Jan 1, 2008

This Bureau of Mines report concerns two subjects important in the application of electric power in mining systems. Electrical transients and their suppression are discussed, and several considerations are explored with regard to the use of explosionproof or other electrical enclosures.

Jan 1, 1979

By D. J. Dollhopf

The objective of this five year study was to investigate the means of establishing non-polluted ground-water and root zone systems in areas where surface mining intercepts physiochemically unsuitable overburden materials. Overburden may need to be sampled on a 60 m grid in order to delineate materials unsuitable for reclamation and to accurately implement selective handling operations. Unsuitable overburden materials were buried successfully in a dragline operation with a minimum of delays, but costs were increased 12 to 53%. After three years the buried material remains above the reestablished aquifer and below the root zone. Construction of a clay cap over the buried material may not be required in semiarid environments. It was shown that some unsuitable overburden materials do not have to be special handled. When inhibitory material constituted <5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile due to mixing/dilution processes. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. At least a portion of the postmine aquifer had hydraulic conductivity rates lower than the premine system, indicating the reestablished aquifer may, in part, conduct ground water very slowly. Postmine ground-water chemical quality in spoil materials had poorer quality compared to premine ground water.

Jan 1, 1981

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

Large quantities of combustible materials are often found in underground metal and nonmetal mines, with support timber most often the predominant combustible material. Oils, lubricants, paper, cartons, and rags are additional combustible materials and are commonly found in maintenance shop areas. Welding and cuting, shorted or overloaded electrical cables, spontaneous combustion, and careless smoking are some of the common fire ignition sources. Inexpensive, reliable fire detection and suppression systems are available to provide early warning of such fires and to isolate and extinguish fires that originate in underground maintenance shop areas. Technology developed and demonstrated under Bureau of Mines Contract H024216, Mine Shaft Fire and Smoke Protection System, may be applied to protect underground maintenance shop areas. The mine area described in this report is a representative ex-ample only; the fire protection system described considers costs, benefits, equipment performance and includes the concepts of: ? Early warning and alarm ? Isolation ? Extinguishment ? Control. Each fire protection system application requires analysis of numerous variables including total mine profile (depth, personnel, escape routes, hazards, etc.).

Jan 1, 2011

By William L. Rice

This Bureau of Mines Open File Report on nickel is one of a series of minerals availability commodity deposit abstracts. Nonconfidential information from the Minerals Availability Program data base covering domestic and foreign nickel properties and deposits has been abstracted for use in this report. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operation information.

Jan 1, 1984

By Christopher Mark, Gregory M. Molinda, Timothy M. Barton

The Coal Mine Roof Rating (CMRR) was first presented at this Conference nine years ago. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, and extended cut evaluation. It has also become truly international, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. The purpose of this paper is to bring the mining community up to date with recent improvements and applications of the CMRR. The most important new development is a streamlined process for determining the CMRR from exploratory drill core. Just three types of information are now required: •Fracture spacing (or RQD) •Uniaxial compressive strength (or axial Point Load Testing) •Diametral Point Load Testing The moisture sensitivity adjustment has also been changed, and new research has related the immersion test to slake durability. Most recently, the CMRR has been implemented in a computer program, which can be obtained from NIOSH free of charge. The program facilitates calculation of the CMRR from either underground or drill core data. Values from many locations can be saved in a single file, and an interface with Autocad allows CMRR contour plots to be integrated into mine planning.

By Ruth F. Brinkley

This circular describes the activities and publications of the Bureau of Mines, Explosives Research Laboratory4 for the fiscal year 1960 (July 1, 1959 -June 30, 1960). Part 1 describes briefly the principal projects that were active during the report period, and presents some data not scheduled for publication elsewhere in the near future. Certain of the results are only preliminary and should be regarded as tentative, pending the findings of the completed investigation. Publications that appeared during the report period are listed and described briefly in part 2. In general, the research activities reported in these publications antedate fiscal year 1960. The published material relating to activities that are still current is indicated by references in part 1.

Jan 1, 1962

By M. O. Serbousek

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed an eight-piece precast reinforced concrete drift set for a small opening. Twenty-two sets of three different member sizes were tested to destruction under two loading conditions. A discussion of the test results and typical failure patterns is presented.

Jan 1, 1969

Three complete connector assemblies and ten separate contacts were submitted to a series of tests to establish the connector permissibility and compliance with the Bureau of Mines&apos; research Contract H 0110423. Test Procedure TPC-0100 was coordinated, and the test plan approved by the Bureau as fully complying with the intent of the contract for the low voltage, medium voltage and high voltage A.C. connectors. The components and connector assemblies have been demonstrated in testing that they meet or exceed all the requirements of the test procedure.

Jan 1, 1972

By Richard J. Mainiero

The Bureau of Mines conducted research to evaluate the optimum design for a rock-breaking explosive charge that could be fired unconfined in a gassy or dusty coal mine without the danger of igniting the flammable atmosphere. Charges of various shapes, with and without cavities, were tested in a gallery using 3-by 3-by l-ft concrete blocks as simulated boulders. For these tests the optimum charge, in terms of cost, weight, and convenience in handling, consisted of a flat l-1/2-lb charge of permissible explosive seven-eighths of an inch thick and 7 in in diameter encased in a l/2-in thick layer of fine salt (NaCI). This work demonstrated that it should be possible to produce an inexpensive explosive rock-breaker charge that would be safe to use in underground coal mines.

Jan 1, 1982

By C. C. Anderson

"While conducting investigations in connection with the helium program of the Bureau of Mines, the Cryogenic Laboratory has improved an apparatus for the rapid and accurate determination of the helium content of natural gas and gaseous mixtures derived from that source. The separation of helium is effected by the use of activated coconut charcoal which, when cooled to liquid-air temperatures, absorbs the nitrogen and other constituents of the gas, leaving the helium in a. spectroscopically pure state. This absorptive property of activated charcoal was discovered- by Dewar3/ in 1875. Several years later, while conducting their original researches on helium in natural gas, Cady and McFarland employed the charcoal method for the absorption and removal of the common constituents of natural gas and constructed an efficient apparatus in which this operation could be effected.4/ Shortly after initiating the government's helium activities during the World War period, the Bureau of Mines adopted, with Minor modifications, the Cady and McFarland apparatus and method of analysis. Seibel.5./ described this modified apparatus and method of procedure as part of a publication on helium-bearing natural gas. Subsequently, the Bureau's apparatus for helium analysis has been simplified and improved to facilitate more rapid and positive operation. The apparatus and method of procedure now being used by the Bureau of Mines Cryogenic Laboratory arc described in this paper.The personnel of the Bureau of Mines Cryogenic Laboratory has improved and brought the helium apparatus described herein to its present state of perfection. The writer's contributions have been-of minor importance, and he wishes to give the various members and former members of the laboratory staff full credit for the improvements they have made. He also desires to express his appreciation for suggestions and criticisms offered during the preparation of this paper to the following members of the Petroleum and Natural Gas Division, Bureau of Mines, which now includes the Amarillo Helium Plant and Cryogenic Laboratory: H. A. Cattell, chief engineer; C. W. Seibel, supervising engineer of the Amarillo Helium Plant; W. M. Deaton, chemist-in-charge of the Cryogenic Laboratory; and H. S. Kennedy.The quantitative determination of helium in a gaseous mixture is accomplished by the removal of the other constituents from the sample, either by chemical or physical Means, leaving only the helium which can be measured directly. Chemical methods, when applied to natural gas, require the burning of the hydrocarbons in oxygen, the, absorption of the resulting carbon dioxide in a caustic solution, the removal of the excess oxygen in a suitable solution such as an alkaline pyrogallate, and the elimination of nitrogen by sparking or by combination with hot calcium or magnesium.. Such procedures are very slow and tedious compared with the physical method which employs the absorptive property of activated charcoal to effect the separation of the other constituents from the helium."

Jun 1, 1934

By C. W. Owings

One phase of Bureau of Mines health and safety work is promotion of the use of safe and effective dust-collecting devices in connection with rock drilling in coal mines. To insure that adequate equipment of this type is available to the coal-mining industry, the Bureau of Mines conducts investigations and issues approvals for dust-collecting equipment that meets the requirements of a schedule established for testing dust collectors intended for use in connection with roof drilling for roof bolting and for other rock drilling. 6/ Performance tests are conducted under the provisions of this schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for approval and lists drill-dust collectors that have been granted approval as of January 31, 1956. The addresses of manufacturers of approved devices are listed alphabetically at the end of this circular.

Jan 1, 1956