Search Documents

By J. Eloranta

"Previous work indicated that the annual per-capita consumption of raw aggregate material averages about 10 tons; half of which is produced by blasting. Given a population of approximately 320 million in the United States alone, this amounts to 1.6 billion tons of blasted material annually. It was also estimated that up to 20% of the blasted material in aggregate operations is smaller than 6.35 mm (1/4inch) in size. Thus, about 320 million tons (i.e. 1 ton per capita) of byproduct is produced annually and sold at significantly lower prices or potentially discarded in waste dumps."

Jan 1, 2017

By He Guangyi, Han Zhilong

This paper introduces the new technology of deep-hole blasting with water-soil mixed stemming to exposed stonework. Nine aspects of advantages are drawn in the paper based on tests of different types of charge and stemming under the conditions of different geology, height of bench and diameter of drill.

Jan 1, 1998

By John C. Brulia

PowerAN is a tradename of Atlas Powder Company for a new line of explosive products comprising blends of emulsion and ANFO in a variety of bulk and packaged grades. The bulk PowerAN grades are either augered or pumped depending upon emulsion content. Augered PowerAN blends contain up to 60% emulsion. Pumped PowerAN grades have an emulsion content of 75% or higher. The blending of PowerAN is usually accomplished at the borehole to satisfy specific borehole conditions. Packaged PowerAN grades are produced in several types of mix plants in diameters of 4" and greater. PowerAN 300 (30% emulsion) and PowerAN 500 (50% emulsion) are the two most popular grades and their chief application is as an economical, high energy replacement for ANFO HD in wet holes. PowerAN combines the cost effectiveness of ANFO with the high performance of emulsions, permitting the blasting engineer to strike an optimum balance between drill pattern expansion and increased productivity according to need.

Jan 1, 1985

By Tom Watts

The practice of pumping bulk blasting agents is regulated by many agencies around the world. The explosives manufacturers have done an excellent job of hazard and operability studies allowing criteria to be established for the safe pumping of water based blasting agents. The challenge of a Bulk Trucks or Mobile Manufacturing Units (MMUs) manufacturer is to take the objectives of the regulatory agencies and the explosives manufacturers and responsibly design and build MMUs that are safe, compliant, and cost effective without compromising serviceability.

Jan 1, 2011

By Paul N. Worsey

Disturbed zones of rock have been measured for blasted highway rock cuttings by Matheson and Swindells of the Transport and Road Research Laboratory (TRRL) of Great Britain. These zones have been shown to be directly attributable to the blasting process and accordingly vary in depth depending on blasting technique. Perimeter blasting such as smoothwalling and pre-splitting has been shown to be effective in reducing the depth of disturbed rock. Although extensive work has been carried out on surface excavations for medium diameter (l00mm) blast holes, none has been undertaken for underground excavations.

Jan 1, 1985

By Norman Paley, John Kells

The climate and location of the Red Dog Mine present several challenges to blasting operations. The mine is located north of 68º latitude, in an area of continuous permafrost. Ground temperatures are below freezing year-round and air temperatures range from -40 to 70°F (-40 to 20°C). Because there is no overland access to the mine, the entire year’s supply of bulk explosives, approximately 7,000,000lbs (3,175,000kg) is shipped in by barge during the 100 day shipping season when the port is ice-free. The first week in July is the earliest that new product arrives at the port. Emulsion usage is maximized from mid April through October when surface water fills the blastholes during drilling. This necessitates that a considerable portion of the bulk explosives are stored for 10 months or more before usage. The emulsion is routinely pumped from the ISO containers at temperatures of 20ºF (-7°C). The mine engineers conducted a testing program during the 2001-2 blasting season to identify the bulk explosives best suited for the conditions at the mine. A secondary goal was to decrease the usage of sensitized emulsion, as this is the most difficult portion of the explosives order to ship. To ensure repeatability when transferring the results to the day-to-day blasting operation, the majority of the testing was incorporated into normal blasting operations in the field. The mining methods used at Red Dog Mine make direct fragmentation analysis impractical and performance testing in the field relied primarily on VOD measurements. The products were also tested for their ability to be pumped in cold temperatures.

Jan 1, 2004

By Dr. Zach Agioutantis, Elliott Morgan

The explosives, mining, and heavy civil industries consistently battle the uncertainty that is associated with working with a heterogenous medium like rock in blasting. This has led to studies to increase fundamental understanding of material response under dynamic loading that is associated with blasting. This study looks at the dynamic strain associated with blasting the lab Split-Hopkinson Pressure Bar (SHPB) testing while also building off of previous studies with the goal of better understanding the dynamic forces that are enacted on a geologic body during a blast loading event. This is required in order to advance geologic blast response modeling. This is achieved through analyzing the stress and strain values for each specimen that are calculated from strain data collected with a SHPB. Based on this data, the dynamic material response characteristics are able to be determined. Tests were conducted on five Berea Sandstone specimens with a rough length to diameter ratio (L/D) of 1.0. The strain data from these tests were then used to create stress strain curves as well as charts depicting failure stress to both strain rate and failure particle velocities. The tests conducted returned similar results to previous tests results on Berea Sandstone while also showing a correlation between strain rate at failure and failure particle velocities. While further research is needed, there is evidence that SHPB test data could be used in conjunction with the MBF model. The MBF model states that the peak particle velocity (PPV) of blast vibrations can be correlated with deformation (strain) at a given point. With a further understanding of dynamic material response correlated to PPV measurements, further refinement could allow for better prediction of blast performance.

Jan 21, 2025

By Mathias Jern, Ruilin Yang

A blast vibration model has been developed that simulates effects of almost all blast design parameters on the blast vibration peak particle velocity (PPV) from a production blast with multiple blastholes at a given point of interest in the rock. The velocity of detonation (VoD), initiation points, explosive types (density, VoD, energy), charge decoupling, and decking in each blasthole are simulated along with other blast design parameters. The information from signature hole blast vibration and the blast design are the input to the model. The model can be used to assess blast damage in proximity of blastholes as well as far field vibration PPV.

Jan 1, 2019

By Anthony Konya, Calvin J. Konya

The publication, RI8507, from the U.S. Bureau of Mines established an envelope equation that related scaled-distance to peak particle velocity in an attempt to predict ground vibration in the design phase of a blast. This has been further modified by Oriard, Dupont, Konya & Konya, and others to develop more refined prediction models for specific situations to obtain better predictions. While these equations can be an ideal starting point for a greenfield blasting project or a project with no given information, these equations can have errors.

Jan 1, 2018

By Tom McDonald, Rodney Burke

As mining progresses in the West, the depth of material has increased, making highwall stability a major factor in safety and production. The Jim Bridger Coal Mine has made highwall stability a priority, concentrating on safety as well as increasing and improving production. Overburden depths are increasing dramatically; the geological environment consists of medium to soft material, faulting, water, and current pit alignment not favorable to joint planes. Angle drilling the presplit at 20 degrees became necessary as vertical presplit drilling produced wall failures.

Jan 1, 1997

By Richard G. Burdick

The use of explosive charges for generating seismic energy has been around for a long time. For oil-field work or crustal studies, when the target of interest is many thousands of feet deep, the surface waves and similar phenomena are of little consequence. In mining applications, however, when the target is a few tens or hundreds of feet deep, the return signals are often masked by these waves and an accurate interpretation is difficult or impossible.

Jan 1, 1981

By Isaac E. "Chip" Harris

A general understanding is given to how and where blast hole drills are used and what recent developments have taken place with small and large diameter drill hole machines. Indications are that new developments with high penetration rates and large diameter holes are not necessarily the answer to increased production in the field.

Jan 1, 1979

By G G. Paine, C V. B Cunningham, G Harries

The companies of the ICI Explosives Group have successfully used a wide variety of internal computer codes including BOBCAT, KUZ-RAM, ICRAX, XPLODE, BLEND, 3CRACK, MICBLAST, DETON, etc. In recent years the extensive experiences across ICI have been combined into a single compatible model engineered to worldwide technical service and customer needs for the prediction and assessment of blast results.

Jan 1, 1987

By Qi Jinduo, Gong Min

On the basis of actual parameter of wall control blast in Nanfeng mine, China, the process of dynamic stress changing between two column charges was studied recently for a presplit-cushion blast by holographic photoelasticity. In the experimental model, two holes were simultaneously detonated from both ends (four ignition points). The bottom of the holes were loaded more than other parts (heavy charge). Under these conditions, four consecutive isochromatic fringe patterns at different times were acquired in one loading run, and the characteristics of the stress distributions were compared at different places and times in the holes. It was found that interaction types of stress waves vary along the holes. The theory is posed that the stress wave which is formed by the interaction of earlier producing P wave and later S wave along a distributed line charge is the most important part in all stress waves. Research indicates that a heavy charge in the bottom of the holes is crucial to producing a presplit-cushion effect at the bottom. "End Effect" doesn't affect the magnitude of stress along linking lines between the bottoms. The chief fields of the "End Effect" are also explained in the paper.

Jan 1, 1998

By Tie-jun Tao, Ming-sheng Zhao, En-an Chi

"Karst landform is a special kind of geomorphic unit which is often accompanied by a large number of geological defects: caves. In blasting engineering, if there are karst caves around the blast-holes, it may result in higher boulder yield and the generation of flying rocks due to the change of burden which is very hazardous for the safety of surroundings. The models of rocks with karst caves from blasting holewere built by the software of ANSYS/LS-DYNA. The results of computation simulation show that thecave can increase more free surface for blasting and leads to a broken zone around itself. Thus rockmass around the cave will fly toward inside and it will result in undesirable result of whole rock mass to be blasted. In addition, the models of rocks with karst caves in different shapes were simulated and thecomputation results show that the caves in round shape have higher load resistance capability than that the caves in rectangle shape. All the simulation results can offer effective guidance for blasting design. The models of rocks with karst caves were built in different distances and shapes from blasting hole by the software of ANSYS/LS-DYNA. The effect of different karst caves on blasting stress and blastingresult were studied."

Jan 1, 2017

By Dale S. Preece, Ruilin Yang

"Air-decks are often employed for presplitting along the final highwall of a blast and are sometimes also included at the bottom or in the middle of explosive columns in the production portion of a blast. Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidlyattenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that theresulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of theexplosive."

Jan 1, 2017

By Joshua Hoffman, Braden Lusk, David McLane, John Rathbun

The research conducted previously on Shock-Tunnel Waveform Analysis gave a brief insight into the propagation of a shockwave within a shock-tunnel compared to that of an open air arena test. As a refresher, a shock-tunnel is an energy channeling device used to simulate the effects of a large scale detonation with significantly smaller charge weights; having the ability to conduct tests in this fashion can greatly reduce the costs of testing products.

Jan 1, 2012

By Ran Tamir

"This document introduces the use of drone generated aerial photography to collect and analyze fragmentation data for both muck piles and post crusher stockpiles in order to support the continuousimprovement process. In tandem with photo analyses software, drone imaging gives mines and aggregate sites a fast, accurate and economical method of benchmarking and optimizing the process of size reduction to spec."

Jan 1, 2017

By Michael Wieland

The thrust of this report is to overcome some of the technical deficiency in the scientific methodology that correlates the work output during a charge explosion to the resulting toxic fumes. Thermodynamic work-principle models yield (undissipated) shock and heave results for shooting underwater and in rock stratum with related toxic fumes. Underwater circumstances yield reliable test data for the work process, though questionable or no fume results. Work-output measurements in rock shots remain difficult if not intractable, though some fume reports exist. Underground tests with thick-wall metal pipe bombs yield consistent toxic fumes trapped within the test chamber. The work output, rendered as fragment kinetic energy, can be inferred from the well-tested theory of R. W. Gurney, originally designed for military ordinance. Therefore a work-principle model for cylindrical pipe bombs was developed to predict fragmentation work output and reaction-zone fumes, permitting the double comparisons to reported and inferred results.

Jan 1, 2010

By Paul Worsey, Braden Lusk, Seokbin Lim

This paper discusses the theory and experiment involved in the discovery of the mechanisms of Linear Shaped Charges, which are much different from those for Conical Shaped Charges. Linear Shaped Charges (LSC) have been assumed to function in the same manner as Conical Shaped Charges (CSC) in the published literature on the subject. Much work has been done on CSC for military purposes, but there is limited information about the mechanics of LSC. Previous theories have cited the formation of a Monroe Jet as the dominant process. The Monroe Effect describes what happens to a target below the charge following detonation of the charge, and prescribes a fluid jet process for penetration. The fluid jet comprised of the liner material is the cutting device in CSC and has been extensively studied. Recent work at the University of Missouri at Rolla (UMR) cutting concrete with LSC has surprisingly shown that there is not a fluid jet process in LSC. After completing several reinforced concrete penetration tests, minimally deformed copper blades were found in the debris. Initially, the blades were suspected to be misfires or malfunctioned charge remnants. However, results were good and blades were found after every single test. Upon closer inspection, the ribbons were found to be folded copper and they were suspected to be the bottom liner of the LSC. A test series was conducted to verify the new theory by experiment.

Jan 1, 2005