Search Documents

By Aaron S. Bradshaw, Ryan M. Coulson

The offshore wind industry in the United States is slowly emerging with the recent construction of the first offshore wind farm located off the coast of Rhode Island. The turbines at the Block Island wind farm are supported by piled jacket structures, which historically have been used for much heavier oil and gas platforms. Offshore wind turbines have unique design requirements and the axial behavior of the supporting piles under cyclic loading is important to design. Cyclic degradation along the pile shaft can affect the capacity, deformation, and stiffness performance of the foundation and of the structure as a whole. This paper proposes a strain-based approach to estimate the fatigue (or endurance) limit of a cyclically loaded pile that may be applicable to long-term service loading. The method is applied to an existing load test dataset and the analysis results appear consistent with the observed pile response. INTRODUCTION The demand for renewable energy has been increasing in recent decades and wind power has seen a dramatic increase in popularity. In Europe, as of 2017 there were 4,149 grid-connected offshore wind turbines across 11 countries (windeurope.org), many of which are supported on monopile foundations. It wasn’t until recently (2016) that the first offshore wind farm was constructed in the United States off the coast of Block Island, Rhode Island. The project included 5 piled jacket structures founded in terminal moraine deposits. Future offshore wind development along the U.S. eastern seaboard could possibly utilize jacket structures in granular foundation soils. Loads from wave, wind, and turbine rotation induce cyclic loads on the foundation that have on the order of 108 loading cycles over the service life on the structure (Schneider and Senders 2010). Turbines located along the U.S. east coast have the added risk of hurricanes. As shown in Figure 1a, the lateral loads on a jacket structure are transferred primarily as axial compressive and possibly tensile loads on the supporting piles depending on the weight of the structure. The friction along the shaft of the pile can be prone to cyclic degradation, leading to reduced pile capacity and stiffness, and increased deformations. An offshore wind turbine foundation must be designed for a variety of limit states including ultimate, serviceability, and fatigue limit states. For a jacket structure this would include an analysis of the ultimate axial pile capacity, axial stiffness, and axial deformations, all of which can be affected by cyclic loading both under extreme (i.e. storm) conditions as well as long-term service conditions. Axial pile stiffness is needed, for example, to estimate the natural frequencies of the structure as a whole and to assess dynamic and fatigue loads. The structure must be designed such that its natural frequency remains outside the loading frequencies of the waves and turbine blade passing frequencies to avoid resonance. Therefore, prediction of the axial response of the piles is important to the design of these structures.

Jan 1, 2018

By Mandy Korff

Walls consisting of CFA-piles are often used for vertical cut offs for building pits. Several methods of installation and geometry may be used and sizes, depths and strengths of walls necessary vary widely. Based on experience with secant CFA-pile walls in The Netherlands, requirements for this type of wall can be set with a risk management view to it. This paper describes those requirements, based on specific local conditions.

Jan 1, 2006

By Roger A. Bullivant

As the UK's foremost domestic foundation underpinning contractor over the last 25 years it has become abundantly clear that the size of the repair market, some £500m per annum is a significant waste of resource and cost. To experience this scale of foundation failure in mainly new construction less than 20 years old is unacceptable. This is being further endorsed by our contracting experience in the USA over the last 10 years. Our foundation repair systems are mainly based upon the use of driven mini piles and it was considered appropriate that this type of pile should be upgraded and used on new build construction where the ground was marginal or bad.

Jan 1, 1995

By Patrick O. Shires, Harry W. Schnabel

With stable building sites becoming scarce in the greater San Francisco Bay Area, the new Summit Senior Care Facility is being built into the side of an unstable hillside adjacent to the San Ramon Regional Medical Center in San Ramon, California. This hillside has had a long history of instability and the site of the new Senior Care Facility required excavation into both a historic old landslide and a more recent active landslide. After a thorough geotechnical study, it was concluded that the best way to build the new facility would be to construct a tied-back retaining wall in the area of the old landslide, since it extended off-site onto two adjacent properties, and remove the active landslide and replace it with compacted fill before cutting into its toe area with an additional tied-back retaining wall. The design was further complicated by the proximity of the site to several active faults. In the area of the old landslide, the combination of an ascending slope behind the wall, landslide forces and seismic forces resulted in total design pressures between 365 to 4,575 PSF for a wall with a maximum height of 30 feet. The wall for the old landslide was constructed by first drilling and placing steel soldier piles in concrete. The tip of the soldier piles extended a minimum of 12 feet below the landslide plane that was up to 36 feet below the bottom of the wall. Permanent double corrosion protected tiebacks were then installed through the soldier beams and anchored below the slide plane. A shotcrete facing was then installed on the face of the wall. BACKGROUND The site of the Summit Senior Care Facility is located on the southwest flank of Mount Diablo adjacent to San Ramon Valley which is characterized by gently rolling hills. The San Ramon Valley Regional Medical Center, which opened in 1990, is located to the north and an existing church is located to the southwest. There are also private residences located to the southeast. The site is shown in Figure 1. Numerous faults run close to the site, the most significant of which are the Calaveras and Pleasanton faults. The site has also had a long history of slope instability and has been the subject of numerous investigations. Studies conducted in 1979 and 1984 concluded that there was a landslide in the area and recommended that a buttress shear key be constructed between the subject site and the existing church for a sewer main as well as removal and replacement of the head area of the old landslide to stabilize the hospital site. While two previous geotechnical studies in 2008 and 2016 identified slope instability, they did not recognize the genesis and limits of the old landslide on the western portion of the site or the limits of the active landslide on the eastern portion of the site.

Jan 1, 2018

By Ali Porbaha

The use of soil nailing technology as a cost effective alternative for excavation support and slope stabilization has substantially increased in the United States during the last decade. For example, in the past thirteen years, more than 185,800 square meters of soil nail walls have been constructed in California alone. The conventional soil nail systems pose difficulties when ground conditions are subject to caving, for instance for silty sand (sugar sand) or cobbles and boulders. The construction industry has developed self drilling hollow bar systems (or pressure injected bored, IBO) that combine both drilling, placing and grouting in a single operation as a solution to speed up construction. While the system is extensively used for temporary applications, nevertheless, some concerns, particularly about corrosion, has limited the use of this technology as a permanent system in North America. This study presents several issues related to self drilling soil nail systems, the results of a field investigation and a summary of the research project.

Jan 1, 2006

By A. Holeyman

The displacement compaction piles described in the paper are installed using a heavy casing or tube and an internal drop hammer. The casing which initially is closed at the bottom by a sand plug displaces the surrounding soil during the driving. Additional sand is rammed down through the casing during the extraction of the casing. The applications and limitations of the method are reviewed in the paper. The importance of checking the sand compaction piles during and after the installation is stressed. Indications of the compaction of the surrounding soil during the driving can be obtained by comparing the initial and the redriving logs of the casing as well as from the volume of sand added. A method to estimate the increase of the mean cone resistance as measured by CPT tests in sandy and silty soils is presented. The governing parameters are the volume of the added sand, the granulometric index and the initial cone resistance.

Jan 1, 2010

By Steven Dapp

A new hyperbolic model for generating P-Y curves is developed for use in lateral analyses of cemented soils (a ?C-F? soil with both cohesive intercept and friction angle), and includes degradation of the static loading soil response to model the effects of load cycling (repeated loading) with load cycle number. The p-y curves, for both static and cyclic loading, were derived from full-scale lateral test results conducted on a set of six drilled shafts in a loess deposit at the Kansas DOT test site. Values of the model parameters obtained from the load testing at this site are presented, as well as a discussion of the model parameters effect on the results such that the model may be rationally applied to other sites with C-F type soils. A step-by-step procedure is presented to illustrate the application of the model. Correlation of the model to the CPT cone tip resistance (qc) from CPT testing is made, as this was found to be the most reliable; However, the model is applicable to other methods, both in-situ and laboratory, of assessing the soils strength.

Jan 1, 2011

By D. P. Nicholson

The current phase of office development at Canary Wharf in the London Docklands includes twelve multi-storey buildings varying from eighteen to forty stories in height. The area of Canary Wharf South comprises five multi-storey buildings with low level in fill podium and garden areas. Three of these multi-storey buildings have "pile-cap" designs where the entire building load is applied to the piles. The remaining two buildings have "piled-raft" designs where allowance is made in the design for part of the building load to be transferred to the raft formation. Using a piled-raft design approach has enabled savings to be made on the number of piles used below the raft. This paper describes the calibration analysis undertaken to validate the design method. The ground conditions at the Canary Wharf site are typically fill and recent gravel deposits over the overconsolidated clay and sand of the Lambeth Group. Below these strata is the Thanet Sand. The Lambeth Group provided the founding layer for the raft and contributed to the pile shaft resistance. The Thanet Sand stratum provided the bearing layer for the 1.5m diameter base grouted bored piles. The piled-raft design required an assessment of the building load transfer through the raft to the formation layer. This load transfer led to significant increases in effective stress in the soil below the raft and thence a corresponding increased the capacity of the piles. This interaction of the raft with the prepared formation contributed to between 27% and 45% increase in total vertical load carrying capacity of the piled-raft substructure compared with the pile-cap design method. The development of the piled-raft design was carried out in three main phases: ? Development of the approach and validation analyses. ? Design work on various schemes resulting in detailed design packages. ? Validation analyses using full 3D finite element analysis (presented herein). The validation of the piled-raft design approach was initially carried out against published case histories for piled-raft interaction. To improve on the validation work a full 3D finite element analysis of a simplified pile raft and superstructure (which contributes stiffness to the raft) was undertaken; the analysis included only a quarter of the structure due to assumed symmetry of the structure and vertical loading. This 3D validation analysis is presented herein. The analysis was carried out using the Oasys LS-DYNA finite element program. Prior to carrying out the analysis of the piled-raft an initial finite element analysis was carried out to back analyse a fully instrumented field pile test providing accurate modelling of a single pile performance. This back analysis allowed confidence in the soil parameters used in the 3D model; comparisons of shaft and base resistances between the pile test and the FE model calculations for the single pile are presented. The parameters provided in this work were then carried into the full 3D model of the piled-raft. The 3D model of the piled-raft structure included 18 piles (12 full piles and 6 half piles on an axis of symmetry of the model).

Jan 1, 2002

By Brock Wallis, Steve Davidow

The following text will present the concept of rock socketed drilled shafts used to support electrical substation structures, and discuss the cost and schedule risks that traditional design responses to unforeseen shallow rock can pose to a project. Design considerations will be detailed, including rock characterization, shear strength of drilled shafts, and modeling lateral resistance of the shaft and surrounding rock. The specific case of drilled shafts installed for heavily loaded structures at the Moxie Freedom Substation will provide an example of how close collaboration between the engineer and contractor to refine designs based on site-specific feedback can provide tangible benefits to the project. In this example, value engineered designs resulted in an approximate 40% reduction in shaft/concrete volume and a 60% reduction in total rock socket depth. PROJECT OVERVIEW The Moxie Freedom Project included the construction of a new 500 kV switchyard in Berwick, Pennsylvania. The foundation contractor was selected to install both small and large diameter drilled shaft foundations to support the structures within the switchyard. The small diameter shafts were utilized to support transformers, switches, bus supports and a static mast, while the large diameter shafts were used to support one 180-foot monopole and six H-Frame structures. CHALLENGES: ROCK SOCKETED DRILLED SHAFTS Available geotechnical data at the time of bid included limited borings and seismic refraction. The borings were not located at every structure, and the contractor and design engineer were left to interpret desktop studies and geophysics to determine the probable site-specific conditions at each foundation. The data suggested substantial variability in the quality and depth to bedrock across the project area, indicating significant risk of deep embedment into bedrock at all seven large diameter shaft locations. Rock socketed drilled shafts pose unique challenges for both designers and contractors, and the topic has become a focus of national foundation organizations. Traditional design models result in deeper and/or larger diameter shafts where rock is encountered. In the case where site-specific geotechnical conditions are not clearly understood and rock is encountered at shallow depths, this can lead to significant additional rock drilling, impacting overall project cost and schedule. Rock drilling can result in more than ten times the cost of soil drilling and can easily take in excess of ten times longer to excavate.

Jan 1, 2018

By Rolf Katzenbach

The principle questions related to the design of deep foundations especially in soft soils are the stability and the cost optimised settlement reduction to prevent possible damages and to minimise the deformations of the adjacent infrastructure. The present develop­ments in the design of deep foundations lead to the design approach of the Combined Pile-Raft Foundation (CPRF) which offers a lot of new possibilities, e.g. the utilisation of the CPRF for horizontal loading or the use of the subsoil as a geothermal storage system.

Jan 1, 2006

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By James E. Maccariella

Replacement of an existing movable bridge with a new low level fixed bridge would not accommodate potential future navigation traffic. In order to replace the existing bridge in a cost effective manner, while accommodating the potential future needs of the Port of Salem, a new bridge was proposed that would permit conversion to a vertical lift type movable bridge should a potential need for upstream navigation warrant such a project in the future. Drilled shafts were found to be the most desirable foundation type for the replacement of the Route 49 Bridge over Salem River. Their ability to resist scour, be constructed without cofferdams, adequately resist vessel collision forces, and accommodate conversion to a future vertical lift bridge allowed the project to meet both the needs of the New Jersey Department of Transportation and the Port of Salem.

Jan 1, 2005

By Christian Besson

This article describes the implementation of a new jointing process for use between diaphragm wall panels. This process was initially introduced on the SOCATOP work site in uburban Paris (which involved the closing of the western section of the A86 bypass road), on a tunnel ventilation shaft. This brand new system upgrades the potential offered by other types of joints available and enables both ensuring the continuity of panels for structures over 40 m in depth under the strictest safety conditions and constructing shafts with diameters of less than 15 m. A patent for this process has recently been filed.

Jan 1, 2002

By Kodi Ranga Swamy, N. Sankar, M. Akhila

"Until recently, liquefaction-related studies concentrated on clean sands believing that only sands are susceptible to liquefaction. However, a few earthquakes like 1976 Tangshan earthquake, the 1989 Loma Prieta earthquake, the 1999 Kocaeli earthquake, the 2010 Chile earthquake, and the 2011 Christchurch earthquake, etc. showed that sand with fines could also liquefy. The research findings on liquefaction of silty soils are limited, and several structures constructed on such soil deposits are damaged during the past earthquakes. Some previous results of research on earthquake events show an increase of liquefaction resistance in silt soils with increase the fines content, but some report the opposite trend. This study presents the results based on undrained triaxial cyclic tests which were carried out on the fine sand with fines (0%, 10%, 20% and 40% fines). The samples were prepared at the required unit weight (Dr = 50%) and saturated by using back pressure and cell pressure increments. Each consolidated sample is subjected to cyclic loading with sinusoidal wave load form at a frequency of 1 Hz. The liquefaction resistance is evaluated in terms of cyclic stress ratio required to cause 100% pore pressure or 20% failure strain occur at 15 numbers of load cycles. Results are presented in forms of pore pressure build up and axial strain propagation plots. As the fines content increased, an increase in liquefaction potential was observed.INTRODUCTIONLiquefaction and related phenomenon have been responsible for tremendous amounts of damage all around the world. In general, the liquefaction may occur in fully saturated sands, silts and low plastic clays. When the saturated soil mass is subjected to seismic or dynamic loads, there is a sudden buildup of pore water within a short duration, and it could not dissipate which leads to reducing the effective shear strength of soil mass. In this state, the soil mass behaves like a liquid and causes large deformations, settlements, flow failures, etc. This phenomenon is called soil liquefaction. As a result, the ability of soil deposit to support the foundations of buildings, bridges, dams, etc. is reduced. Liquefiable soil also exerts a higher pressure on retaining walls.This lateral movement of soil could cause settlement of the retained soil. A sudden build-up of pore water pressure during quake also triggers landslides. Liquefaction damages of structures are commonly observed in low-lying areas near the rivers, lakes, and oceans."

Jan 1, 2017

By Michel Bustamante

The occasional substandard performances of continuous flight auger in particular soil conditions have prompted the drilling rig manufacturer to improve the standard CFA in order to reduce its negative effects. A real improvement of interest was the launching of the double rotary CFA system. The promising features of the latter have incited the authors to implement an extensive experimental research on pile constructed using this type of technique but in the specific context of cohesive soils. Short-term static load tests were carried out on a total of 9 test piles of various installation techniques in order to compare the respective performances. The promising features of the double rotary CFA have incited the LCPC & Durmeyer Company to implement an extensive experimental research on this type of pile technique but in the specific context of cohesive soils and more particularly in clayey marls. After load tests completion the research has been completed by an excavation of the double rotary CFA piles. All the collected data concerning the implemented program are reported.

Jan 1, 2002

By Joel Moskowitz

A new office complex is being constructed within 25m of the Hudson River in New Jersey. The project, about 140 m by 100 m, will include 4 basements under the entire footprint. The perimeter was to be secured by a 0.8 m thick diaphragm wall, laterally supported by high capacity tieback anchors to rock. Columns were to be supported on footings or piers to rock at a nominal bearing pressure of 3.8 MPa at depths up to 17m. Although some variation in rock quality was observed in borings, a substantial vertical seam of weathered and/or decomposed rock, 1 to 2 meters wide by as much as 8 meters deep, was encountered during construction necessitating field redesign. In some locations the seam dipped below more competent rock. Footings were redesigned for support on drilled caissons, or soft rock was excavated and replaced with concrete necessitating a reduction in bearing pressure of the footings by one half.

Jan 1, 2002

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibrations generated during the driving of piles or sheet piles can affect buildings or installations in the ground. However, observed building damage is not always caused directly by dynamic effects, but can also be related to foundation conditions. The importance of geotechnical conditions is usually not taken into consideration in most vibration standards. This paper describes how building foundations, and in particular mixed foundation types, are especially sensitive to ground vibrations. A method is presented for assessing the risk of settlement due to vibrations in granular soils. Also, a simple concept is proposed for estimating settlements in the vicinity of driven piles.1. INTRODUCTIONUnder unfavorable conditions, the installation of piles or sheet piles can cause damage to buildings or other structures on the ground. Frequently, such damage is attributed to vibrations of the building itself. In many countries, national or international standards are used to assess the risk of vibration damage to buildings. As such standards are often prepared by engineers with little or no geotechnical knowledge, the effects of ground conditions on vibration propagation and damage to building foundations are generally not recognized, and damage criteria based solely on the dynamic response of buildings neglect the importance of damage mechanisms governed by geotechnical conditions. One potentially important damage mechanism is differential settlement below buildings, especially when these are founded on loose granular soils. When seeking guidance in the literature, little or no information can be found regarding methods to assess permissible levels of ground vibrations with respect to risk for settlement.This paper focuses on building damage that can be attributed to foundation conditions. In the case of ground vibrations due to pile and sheet pile driving, differential settlements are of particular importance as the ground vibrations attenuate relatively rapidly from the source. Consequently, settlement below part of the building, which is located close to the vibration source, can be significantly larger than at a distance further away.Piles are often a cost-effective foundation solution for buildings on loose and compressible soil, frequently located in urbanized areas. Sheet piles are commonly used as support for deep excavations. While impact driving is most commonly used to install piles, vibrators are frequently used for driving (and extraction) of sheet piles. It is important to recognize the fundamental differences between impact and vibratory driving. During impact driving, the pile is subjected to stress waves of short duration. The driving process creates vibrations, which radiate from the shaft and/or the toe of the pile into the soil. The larger the intensity of the stress wave, the larger the dynamic force and the intensity of ground vibrations. In addition to the vibration intensity, which often is expressed in terms of particle velocity, also the vibration frequency is important. When the dominant frequencies of the generated vibrations harmonize with the resonance frequency of buildings or building elements, the risk of building damage increases."

Jan 1, 2014

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

By Carole L. B. Mitchell

The increased use of micropiles and soil nailing presents a growing database of verification and sacrificial load test data. In Washington State, the use of micropiles is becoming common, and soil nails are now almost as widely used as tiebacks; yet the state of the practice in understanding load transfer rates has not improved. This research compiles load test data for micropiles and soil nails from Shannon & Wilson?s records in the Puget Sound region of Washington. Ultimate and maximum load transfer rates for design are correlated to geologic units and soil types found in the region. Variables such as pressure versus tremie grouting, hole diameter, soil density/consistency, and the presence of groundwater are compared to load transfer rates for similar geologic units and soil types. Results are also compared to published PTI, AASHTO, and FHWA guidelines. Our results indicate that published ranges may be conservative for some soil types in the Puget Sound region, especially for micropiles. Performing verification tests to failure instead of typical verification or performance tests is needed to improve correlations and provide less conservative design load transfer rates.

Jan 1, 2006