Search Documents

By J. Beddoes

The various microstructural factors that influence the creep resistance of y-titanium aluminides are presented and discussed. Titanium aluminides have potential for a variety of intermediate temperature applications in both gas turbine and reciprocating engines. While it is well established that the 'fully lamellar' titanium aluminide microstructure offers superior creep properties, the particular influence of lamellar morphology, third phase precipitation, and grain boundary structure in controlling both the primary and tertiary creep behaviour is presented. The results are primarily based on tensile creep experiments undertaken using several titanium aluminide intermetallic compositions processed via powder metallurgical techniques, investment casting and Bridgman directional solidification. The results indicate that lamellar structure and precipitate formation have a major impact on primary creep, while microstructural degradation through both lamellar and precipitate coarsening influence on the onset of tertiary creep leading to fracture. The results are used to design a creep resistant microstructure produced by directional solidification and the effectiveness of this designed microstructure is demonstrated through 10,000 hour creep tests.

Jan 1, 2004

By Sheila E. Daniel

"Since 1989, the Mine Environmental Neutral Drainage Program (MEND) has sponsored research into ways of reducing the environmental impact and financial liabilities associated with Acid Mine Drainage from tailings and waste rock. Toward this overall objective, Kilborn was contracted to review the use and applicability of passive treatment systems for acid mine drainage.Experimentation using passive systems to treat acid mine drainage has been ongoing since the early 1980's in North America. Passive treatments are generally considered an attractive alternative to active lime treatment, since they require minimal human involvement, no power, and only seasonal or periodic care and maintenance after establishment. Most attractive is that initial capital cost to implement a passive treatement system is generally low to moderate. Ongoing operating costs are similarly low when compared to active treatment systems.Passive treatment systems currently used, or under investigation to treat acid mine drainage include: anoxic limestone drains, aerobic wetlands, reed bed wetlands, compost wetlands, microbial systems and bioabsorption systems. These wastewater treatment systems utilize the chemical, biological and physical removal processes that occur naturally in the environment to improve wastewater quality, including: oxidation, reduction, coagulation, adsorption, absorption and precipitation; microbial activity; and, gravity aeration and dilution. The rates at which these processes occur determines the loading which can be treated and the effectiveness of the system.The results of our literature review will be summarized, and insight provided into the applicability of passive systems to treat acid mine drainage from Canadian Mines."

Jan 1, 1995

By K. W. Fritzsche

The prosperity of any nation depends, to a large extent, on its natural resources such as oil, coal, 'metal, timber, waterpower, and fertile soil. Each one of these resources forms the basis of a huge industry. The mining and smelting industry ranks among the first since it paves the way for a number of other industries. The mines and smelters provide a market for electric power, coal, timber, and agricultural products: other industries in turn provide a market for metals and non-metals. The real pioneering, however, is done by the prospector who goes into the wilderness to search for the ores from which the metals are to be extracted for the use of men. Prospecting is an interesting and fascinating occupation. There are many difficulties and hardships in the way but the lure of gold and the vision of finding an outcrop that may develop into a large bank account, within a reasonably short time, will urge the prospector forward. Thus, on the outskirts of this northern hemisphere hundreds of prospectors are searching and toiling and of whom nothing is known or heard until they reach civilization and announce a new discovery. Then a mad rush takes place and everybody who can afford to go will take a gamblers chance and plant stakes in the neighbourhood of the new discovery, or wherever an outcrop of mineralized rock can be found, with the hope of winning a fortune.

Jan 1, 1925

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By Jehan Rondot

Les trois intrusions alcalines de Suzorite en haute Mauricie, bien que non datees, son! sans doute d ,attacher aU)( nombreuses autres intrusions alcalines dispersees sur les blocks Grenvillia et Laurentia et datees de I 050 Ma =t= 10%, done reliees d l'orogene grenvilien. L 'utilisations de la Suzorite est liee d sa forte proportion de phlogopite (>50%). Le rapport Mg/Fey varie de 3 d 7. Sa mineralogie et sa composition particulieres (forte proportion de Mg, Ket H20) en font son attrait.

Jan 1, 1984

By M. A. Roche

The property of the Hudson Bay Mining & Smelting Company, Limited is located at Flin Flon lake, 85 miles northwest of The Pas, Manitoba, on the Manitoba-Saskatchewan boundary. The area is at latitude North 54°, and is approximately 1,000 feet above sea level. The ore-body occurs in amygdaloidal greenstones, which are to be referred to the earliest basic volcanic flows in the district. It was discovered in an outcrop on a point of land jutting into Flin Flon lake, and subsequent diamond drilling proved that it extends under the lake both to the north and south of the point of discovery. After the taking of soundings from the ice during the winter months, it was estimated that l,000,000 tons of overburden, mainly mud and clay, would have to be removed to expose the underlying ore. Flat diamond-drill holes indicated that the ore-body was separated into more or less independent lenses by horses of unmineralized greenstone, and that in places the overall width, including horses of waste, reached 450 feet. These several] conditions were the main factors influencing the management in their decision to adopt an open-cut method for the mining of the upper portion of the ore-body. Before it was possible to commence stripping operations, it was necessary to dam-off the eastern portion of Flin Flon lake, instal pumps, and de-water the dammed-off area. Dams for this purpose were constructed of mine waste rock and clay filler from nearby hillsides. Material for the bottoms of the dams was taken across Flin Flon lake in hopper-bottom barges. Trestles were then built on the dam bottoms and dams were complete by the time trackage was available. De-watering commenced in April, 1930, and was completed by the latter part of May of the same year. Estimated pump output for the period was roughly four billion gallons. Two Morris 10-inch dredging pumps were used, direct-connected to 250 h.p. electric motors. Individual pump capacity was rated at 3,000 g.p.m. against a 150-foot head. Average head for the operation was 50 feet, which increased the total output considerably. The pumps were mounted on floating barges in cribbings of piling driven at the lowest points in the lake bottom.

Jan 1, 1933

By H. C. L. Reemeyer

One of the fundamental trade-offs for copper concentrators is between grinding circuit product size and copper recovery. The capital and operating cost savings and throughput increases for a coarser grind should be evaluated against potential recovery reductions. Other benefits of coarser grinds, such as GHG emissions reductions and favourable effects on tailings and water management should also be considered. This paper assesses the formation of laboratory and pilot test programs, design of process flowsheets, equipment selection, and evaluation methods to determine the most appropriate and economical grind size for a given deposit. The paper will include an evaluation of case studies. INTRODUCTION The majority of the world’s mined copper comes from sulphide deposits, which are mostly processed using crushing, grinding, flotation and dewatering flowsheets to produce copper-bearing concentrates for smelting. Ores must be ground to a sufficiently fine size to achieve an acceptable level of liberation to allow both high recovery of copper and valuable by-product minerals while efficiently rejecting gangue to tailings. Therefore, a key design parameter in process plant design is the grind size of the flotation feed. Copper concentrators use a variety of grind size targets that depend on various factors, including ore mineralogy and the grain sizes of valuable and gangue minerals; the sensitivity of valuable mineral recoveries in the rougher flotation stages to grind size, ore hardness; electricity costs; and mining vs. processing throughput constraints. Typically, copper and by-product recovery increase as grind size is reduced, which can improve revenue, but finer grinds increase power and grinding media operating costs and may have implications for tailings management. This paper explores the trade-offs that should be assessed in determining the optimum grind size, and to answer the question if coarser grinds are worthwhile. METALLURGICAL AND FLOWSHEET FACTORS Recovery-by-size behaviour of sulphide-bearing particles In base metals sulphide flotation, it is typical that flotation recoveries vary by particle size. Metal sulphide particles rendered hydrophobic by collector in intermediate size ranges (e.g. 10 to 100 um) usually show very high recoveries, often approaching 100%. Recovery usually falls away in finer size fractions (<10 um) as fine particles have little inertia and can move around bubbles without colliding and attaching to them. Coarser particles (>100 um) are susceptible to particle-bubble detachment and dropback (Jameson, 2019).

Jan 1, 2019

By A. Saigal

The effect of temperature on the cutting forces during machining of alumina reinforced aluminum composites was investigated, Aluminum 6061, 10% Al2O3 reinforced composite and 20% Al2O3 reinforced composite were tested, A 5/8-inch diameter high-speed steel end mill, a Micro 100 TiN coated single edge endmill cutter and a two-fluted solid carbide insert cutter were used for tooling, The results, in general, showed an increase in the cutting forces as the temperature of the material increased, From the raw data, there are temperatures ranges in which the force data did decrease but they were insignificant with regards to predicting a downward trend. A regression analysis was used to understand which variables had the greatest affect on the forces being generated, The correlation and regression analysis showed that at 600 rpm (velocity: HSS- 98,2 sfpm, Micro 100 cutter - 78,5 sfpm, solid carbide cutter - 192,4 sfpm) the tooling, the workpiece material, built up edge, and temperature were statistically significant factors in the test, Tooling was a significant variable in all testing, The smallest forces recorded during machining were generated with the solid carbide two-fluted endmill cutter, Visually, the solid carbide tooling produced a better surface finish during the testing which made it the tool of choice, In addition, the force data proved that as the cutting speeds were increased, the cutting forces decreased.

Jan 1, 2005

By R. J. Twigg, S. D. Chang

"The production of heavy water, the moderator in a CANDU reactor, is examined following a flow sheet of a typical Canadian plant. The process involves the extraction and concentration of deuterium from natural water through a chemical exchange mechanism with hydrogen sulphide. Consequently, corrosion problems associated with sour environments – the use of hydrogen sulphide - are an everyday problem and have led to the development of a highly refined materials selection and testing program to prevent equipment from failing prematurely.IntroductionHeavy water is a naturally occurring compound in ordinary water and is formed from the combination of two deuterium atoms and one atom of oxygen. Deuterium is a heavy hydrogen atom which has a nucleus of on e proton and one neutron. Hence, heavy water is a combination of heavy hydrogen and oxygen and is chemically known as deuterium oxide. It looks and tastes like ordinary water but it freezes at 3.8°C and boils at 101.4°C. The molecular weight of heavy water is 20 as compared to 18 for ordinary water; the density of heavy water is ten per cent greater than that of ordinary water.Although heavy water and ordinary water exhibit only small differences in their chemical and physical properties, there are large differences in their nuclear properties, the most important of which is the neutron moderating ratio, used to measure the ratio o f the slowing down power to the neutron capture characteristics. For heavy water the ratio is 21000 and for ordinary water it is 50. This high moderating ratio is essential for achieving a high neutron economy. Heavy water is, therefore, chosen as the moderating and heat transport fluid in the CANDU reactor."

Jan 1, 1983

By BRIAN HITCHON

Calcium, magnesium, bromide and iodide extraction from formation waters for use as industrial minerals has occurred in several countries, but not yet in Canada. Potential commercial brine fields exist in th e Upper Devonian Beaverhill Lake Formation of so uthern Alberta, and the Middle Devonian Elk Point Subgroup of north-central Alberta, f rom which calcium, magnesium and bromide are potential products. Iodide contents in fo rmation waters f rom the Upper Cretaceous Belly River Formation and the Lower Cretaceous Viking and Bow Island fo rmations in central and southern Alberta are at the lower range limit of commercial iodide-bearing formation waters elsewhere in the world. Available information is insufficient 10 outline potentially commercial areas in Alberta, but such info rmation can be most easily obtained f rom test borings for shallow natural gas. Lithium is not now produced commercially f rom formation waters but its content should be monitored in view of f uture increased demand for this metal.

Jan 1, 1984

By A. Ghahreman

Activated carbon is proven to be able to catalyze arsenic oxidation in aqueous solution under acidic conditions. A commercially available granular coconut shell based activated carbon (AC) has been evaluated for catalysis of arsenic oxidation in this study. The rapid small-scale column test (RSSCT) has been developed to simulate and predict the performance of a carbon-based arsenic treatment system in a pilot scale reactor. Effects of residence time, aeration rate, and initial arsenic concentration in the influent solution on the AC catalysis of arsenic oxidation under dynamic and continuous conditions were studied by manipulating these parameters during RSSCTs. The effectiveness of the AC on arsenic oxidation was examined over the course of constant diffusivity based RSSCT operation. Residence time and initial arsenite concentration are proven to be the most effective impacting parameters on the arsenic oxidation process. For the 218 min residence time, the highest steady-state arsenic oxidation efficiency achieved was 98% with 1 g/L As(III) being treated at pH=1 under 0.05 L/min oxygen aeration. In a long-running RSSCT, the oxidation efficiency did not seem to deteriorate over a course of 666 hours operation, corresponding to 13986 mL total influent throughput volume. INTRODUCTION Arsenic is toxic to both animals and plants and inorganic arsenicals are proven carcinogens in humans. The increased extraction of low grade and complex mineral resources has introduced high ratios of arsenic into metallurgical processes. Discharge of arsenic by acid mine drainage resulting from mining activities has added intensive pressure on the need for proper treatment (Lawrence & Higgs, 1999). Since trivalent arsenite is more toxic and has lower affinity to solid surfaces for adsorption, many treatment systems initiate with an oxidation step to convert arsenite to arsenate and reach the ultimate immobilization of arsenic by the following precipitation of arsenate (Nazari, Radzinski, & Ghahreman, 2016). Scorodite precipitation has been studied extensively as a means of arsenic immobilization due to its high stability and negligible potential of releasing arsenic (Filippou & Demopoulos, 1997). As a stable ferric arsenate mineral, crystalline scorodite can contain up to 30 wt% arsenic (Paktunc, Dutrizac, & Gertsman, 2008). Arsenic must be in its pentavalent oxidation state in order for scorodite to be precipitated via oxidizing ferrous ions (Clancy, Hayes, & Raskin, 2013).

Jan 1, 2019

By G. R. Guillet

"Bricks made from local Paleozoic shales, and floor and wall tiles made from imported clays, both established record production volumes in 1985 and are the strongest segments of Ontario &apos;s clay products industries. However, renewed interest in traditional materials also supports a good market for clay flower pots and flu e liners, and innovative processing studies are showing promise for possible new production of clay roofing tiles. This paper reviews the highlights of a comprehensive study of Ontario&apos;s clay products industries, completed in 1986. IntroductionFor some years now, Ontario&apos; s clay products industries have been unspectacular in their attempt to cope with the recent recession and the impact of alternative materials. But a strong demand for bricks in recent years has done much to dispel the gloom.Bricks, drainage tiles, sewer pipes, flue liners, structural and partition tiles, and flower pots have been commonly referred to as ""heavy"" clay products, and they have been based largely on local clays and shales. To this list might be added expanded aggregate and mineral wool. Clay refractories, sanitary ware, electrical porcelain , art pottery, and floor and wall tiles are not considered heavy clay products, and are commonly made from a variety of ceramic materials, many of which are imported.Production facilities for heavy clay products often began in Ontario as small family enterprises, using whatever clay was available locally to supply the local market with building bricks and other clay products needed for construction. Improved road systems increased the market range for these plant s, and new technology and industry standards resulted in gradual"

Jan 1, 1988

By E. Y. Carlson

"IN A SHORT PAPER it is impossible to do much more than to list the industrial minerals found in Saskatchewan and to give a brief description of the activity associated with each. I will not attempt to discuss the geology. It is sufficient to say that the settled part of the Province is covered by glacial drift which varies in thickness from a few feet to several hundreds of feet, and that this has hindered the search over much of the Province.CLAYA notable exception to this is the Cypress Hills area in the southwest corner which did not suffer any glacial action and where we find some of the large exposures of Cretaceous clays. In this area, the majority of the deposits are of stone-ware clays which are •an excellent raw material for such products as face brick and sewer pipe. Although the clay cannot be transported over any great distance it is used extensively in Alberta and Saskatchewan in the production of these products."

Jan 1, 1959

By D. Mark Richards

Highland Valley Copper is a large open pit copper mine in the southern interior of British Columbia. Machine guidance technology using the Global Positioning System (GPS), was first implemented at the mine in late 1996 for blast hole drill navigation. The purchase of a third BE49R drill in 1998 completed the change to GPS navigation for all the mine?s drilling. The acceptance of this technology was almost immediate at both the operator and management levels. With the purchase of a new P&H 2800 shovel in 1997, the opportunity was taken to extend GPS navigation to a shovel. Due to communication restrictions, this was not as successful as envisaged. In late 1999, following a cost benefit analysis, a three-shovel trial of Caterpillar?s Computer Aided Earthmoving System (CAES), was initiated. The trial was successfully concluded in June 2000 and a further two shovels were equipped. Acceptance of this system has been very good at all levels, which has undoubtedly contributed to its success. In September 2000, CAES was extended to the dozer fleet with the purchase of a new track dozer. The CAES equipped dozer is used for pit production and project work. It is planned to extend CAES to the rest of the shovel fleet in 2001, along with a production front-end loader and one or two more track dozers.

May 1, 2001

By Alan S. Lock

Large scale feasibility studies for the establishment of oil-seed and cellulose producing crops on mine tailings have been successfully conducted over 1 growing season with the purpose of these crops to be used as feedstock to the biofuels industry. An acid sulphide tailings impoundment in Copper Cliff, Ontario and a near neutral pH goldmine tailings impoundment in Timmins, Ontario were both tested by amending half hectare plots to approximately 1 m thick with residual biosolids from the pulp and paper industry and growing canola and corn on these plots. Full scale agricultural equipment was used to cultivate seed and harvest the plots to prove the full scale feasibility of farming on these biosolids. The vegetation development, growth, yield, quality and composition were assessed to identify the best species that would maximize biomass development for feedstock to the biofuels industry and carbon credits for the mining industry. Groundwater, biosolids and tailings chemistries were investigated to identify potential deleterious impacts of degrading organic matter on tailings metal mobility. Preliminary hydrologic investigations using moisture sensor profiles elucidate potential conservation of water in amended plots. Tailings amended with biosolids have the potential to provide the mining industry with carbon credits and supply feedstock to this new industry while reclaiming brownfields to a new level, utilizing industrial and municipal organic waste material.

May 1, 2009

By C. G. McLachlan

Professor H.E.T. Haultain: To me from time to time the urge comes to say the agreeable thing as well as the disagreeable in commenting on the work of others. It is a prerogative of age. I don&apos;t apologize. To myself I justify my action as based on a long experience of the matters with which I deal, and I like to tell myself that I have a certain responsibility in such matters on account of my detached position. This Noranda article is a very fine contribution concerning Canadian milling, and I am surprised that no word of commendation or thanks has appeared concerning it in the BULLETIN. There is altogether too much written in these days by men rushing into print, concerning laboratory work, that has not been tied into, nor has resulted in application in the field. The authors of this paper have not rushed into print. The preparation of this paper was evidently an uncongenial task. If the authors had been that way inclined, it could have spread over several lengthy papers. It is an important article because it represents an enormous amount of work in the laboratory and the mill, extending over a period of sixteen years, and resulting in fine metallurgical and economic results with a very difficult and involved problem. It is a fine article because it is so well prepared and presented. It deals with an unusual ore condition, but there is much in it of use to every cyanide millman. It leaves very little room for criticism, though there may be differences of opinion in regard to some of the chemistry phases with which I am not conversant. I am struck by the enormous amount of persistent, painstaking, conscientious research work involved, and in the careful, sincere way in which the methods and difficulties have been described. Persistence and sincerity are the key note of the effort. It should have a good educational effect on the rising generation of millmen, and it should continue for long as a work of reference, and a spur to others. There has been an important by-product, the training and development of the young men engaged in the work. Three of them became superintendents of important mills. One was sought for important work in Africa, another has joined a large research organization in the United States.

Jan 1, 1946

By Andrew Thrift

Overview ? Problem ? Research question ? Literature review ? Methodology ? Results ? Discussion and recommendations ? New developments Problem ? Increasingly higher expectations ? Inadequate consultation leads to conflict rather than collaboration ? Consultation practice is often weak on decision-making ? Influence of consultation on planning is Unclear Research question ? Are Structured Decision Processes (based on decision analysis) an effective methodology for involving stakeholders in consultative decisionmaking in the mining industry?

May 1, 2006

By R. W. Allgood

"THE world-wide shortage of elemental sulphur, which became sharply apparent in 1950, has focused attention on the commercial exploitation of sulphur-bearing materials such as pyritic ores, sour natural gas, and smelter gases. Although there •are no known commercial deposits of elemental sulphur in Canada, there are vast quantities of these sulphur-bearing materials. The International Nickel Company of Canada and Canadian Industries Limited have for many years collaborated in an effort to develop economic processes for the recovery of sulphur from the smelter gas arising from Inco's metallurgical operation at Copper Cliff, Ontario. While sulphuric acid has been •produced at Copper Cliff for over twenty years, recent developments will result in a 60 per cent increase in acid production early in 1952 and, later in the year, in commencement of the operation of the largest single unit ever erected for the manufacture of liquid sulphur dioxide.The purpose of this paper is to discuss •briefly the general factors associated with the recovery of sulphur from the Copper Cliff smelter gases and to describe the sulphuric acid operations and the liquid sulphur dioxide development.Processes for the manufacture of elemental sulphur, liquid sulphur dioxide, and sulphuric acid from sulphur-dioxide-bearing smelter gases are well known and in some cases •highly developed."

Jan 1, 1952

By E. Cauda, K. Phillips

"Diesel particulate matter (DPM) exposures are a serious occupational health hazard in underground mines. While the complex nature of DPM makes direct analysis difficult, its primary component, elemental carbon (EC), can be used as surrogate. The near real-time FLIR Airtec monitor measures EC mass based on laser extinction. It was developed for use in underground metal/non-metal mines, and calibrated to the NIOSH Method 5040. Its effectiveness has not been demonstrated in coal mines, however, where coal-sourced EC could produce analytical interference. To gain preliminary insights regarding the Airtec’s performance in the presence of coal dust, experiments were conducted in a controlled laboratory chamber. The Airtec EC results consistently underestimated Method 5040 EC for both respirable-sized and submicron coal dusts. While underestimation of coal-sourced EC bodes well for limiting coal interference for DPM measurement, one key reason for the observed trend was non-uniform coal particle deposition on the Airtec filter. This may be problematic in coal mines where DPM and coal dust occur together in the instance that DPM deposition is also non-uniform. INTRODUCTION Diesel particulate matter (DPM) is an occupational health hazard, and underground miners have the potential for relatively high exposures due to their work in confined environments with large diesel equipment (NIOSH, 2011). DPM is heterogenous and complex in terms of its chemical composition (Birch & Cary, 1996; Noll et al., 2006), but elemental (EC) and total carbon (TC) are often used as analytical surrogates (Birch & Noll, 2004; Noll et al, 2015). EC is the solid “soot” component of DPM, whereas TC also includes particulate organic carbon (OC) (Noll et al., 2007). EC and OC can be measured in filter samples using the standard NIOSH Method 5040 (NIOSH, 2003), and summed to obtain TC. In US mines, TC has been adopted as the analytical surrogate for DPM in regulatory activities. In metal/non-metal mines, personal exposures are limited under 30 CFR Part 57. In coal mines, limitations are made on emissions from each piece of equipment (30 CFR Part 72) rather than for personal exposures. This is because coal dust has the potential to interfere with TC measurements in personal samples. In some other countries, and for non-regulatory purposes in the US, EC is also commonly used as a surrogate for DPM in mine monitoring applications [e.g., see AIOSH, 2013). EC generally exhibits a linear correlation with TC (Birch & Cary, 1996; Noll et al., 2006 and 2007) but unlike TC measurements, which are analytically intensive, EC can be determined more simply using a laser absorption/extinction principle on filter samples (Noll et al., 2013)."

Jan 1, 2019

By A. Carbonari

In order to gain competitiveness and compete at a global level, construction companies should improve their efficiency. The problem is even more relevant in the construction field, whose work processes find it hard to evolve towards new automated methods and techniques in the management field. For that reason, this paper suggests how construction companies could apply new technologies to implement automated management of environmental hazards. Based on a survey regarding the environmental risks presently experienced in construction sites, noise and dust were considered two of the main hazards. So in this paper a networked system for real time remote monitoring of the spatial distribution of dust in construction sites was developed. Such a system would relieve builders from the commitment of on-site surveys, allowing for a continuous monitoring of the site conditions and of the real exposure of each worker and pass-by to the pollutants generated by construction works. The main system requirements considered are: easy to deploy, reliable, as accurate as needed to be able to send real-time warnings and store a good estimation of the real exposure to which involved people have been subject to. So far the research produced a prototypical hardware for dust monitoring made up of wireless sensors which can be easily deployed on site. The sensors were calibrated by means of laboratory tests, where their measurements were compared with those collected by means of highly accurate instruments, which were taken as a reference. Thanks to these experiments, calibration curves for the sensors were worked out, showing also the measurement range of the sensors.

Aug 1, 2013