Search Documents

By M. R. P. Snow

"This paper outlines geotechnical conditions that commonly exist in underground, hardrock mines and the challenges posed for ground-support steel, specifically rockbolts, used in these environments. A model is proposed whereby the in-situ stress and rock-mass classifications (based on Bieniawski’s rock mass rating) form the basis of determining the desired steel properties of the rockbolts used. Based on the ASTM F432 bolting specification, recommended minimum steel properties are defined for three ranges of in-situ stress levels, each with their own six ranges of RMR values. Heat treatment for the steel can be specified once these minimum steel properties are known.RÉSUMÉ Le présent article décrit les conditions géotechniques qui existent fréquemment dans les mines souterraines de roches dures et les défis que cela pose pour le soutien de terrain en acier, plus spécifiquement les boulons d’ancrage utilisés dans ces environnements. Un modèle est proposé dans lequel les contraintes in situ et les classifications de la masse rocheuse (selon la classification de la masse rocheuse de Bieniawski) servent de base pour la détermination des propriétés désirées pour l’acier des boulons d’ancrage utilisés. En se basant sur les spécifications de boulonnage de l’ASTM F432, les propriétés minimales recommandées pour l’acier sont définies pour trois plages de niveaux de contraintes in situ, chacune avec sa propre plage de six valeurs de classification de la masse rocheuse (RMR). Un traitement thermique pour l’acier peut être spécifié une fois que ces propriétés minimales pour l’acier sont connues."

Jan 1, 2016

While this paper is directed towards the ?Bellambie? type of rope attachment, the principles can be applied to any brand of rope fitting however, it is a only a broad outline and the specific installation and maintenance procedures can be obtained from the attachment supplier. The types of attachment to be discussed are:- ?Thimble Type rope cappel ?Wedge Type cappel ?WRC Rope Clamp ? (Rope Glands) ??Hoist and Balance Rope Sockets In each case, the assembly and stripping (disassembly) plus the basic maintenance procedures is briefly described. A guide for Risk Assessment is also included but because of his familiarity with the installation, the end-user is in the best position to draft the final version.

May 1, 2003

By J. Bhattacharya, S. K. Mukhopadhyay, S. K. Pal

"While time and again many authors have categorically stressed the restoration of the environment, very little effort has been made in the mineral industry to develop the economy of environmental control. There are many abatement procedures that search a maze of variants. Among them pricing environmental damage seems to be more logical and easily implementable.IntroductionMining as an operation has a severe impact on the Earth's natural resources. While economical environment control is much sought after, solutions are often varied and complex, and can differ in the problems of single or multiple mine sites.Determination of Optimum use LevelsIn “mining environmental control"" it is required to strike a balance to find optimum use levels. The solution is to find where the welfare benefits equal the cost involved to curb the degree of environmental damage (Fig . I) . In the mining industries this can be done by modifying the production/extraction process itself. For most pollutants, the marginal costs of control will exceed the benefits from further reduction of damage long before the zero pollution damage point is reached (Fig. I). From an economic perspective the optimal alteration of environment by mining would occur at z; pollution continues to be caused by ""zy"" control units, but it would be inefficient to pursue the redemption efforts further because the marginal cost involved would exceed marginal welfare benefits."

Jan 1, 1992

By J. Olaf Sund

"THE November issue of the Bulletin carried in it ""Origin of the New Bruns1viclc Gypsum Deposits"" by J. Olaf Sund. This paper was a digested account of a Master's thesis at the University of New Brunswick which was a very useful compendium of information of gyp-sum in New Brunswick. It was a warded the President' s Gold .Medal and the First Prize in the Graduates' Section of the Students' Essay Competition. The present writer presents his congratulations to the winner of the competition. At the same time he must comment on the use of certain terms and on certain conclusions presented in the paper.The term ""unconformable"" has been used in several places in the paper to describe the relationship of gypsum to anhydrite in various deposits in New Brunswick in a sense which is quite alien to the accepted meaning. It has long been known tl1at the gypsum at the surface or near the surface in deposits in the Atlantic Provinces has come from hydration of anhydrite by surface and ground waters. The gyp-sum must be looked upon then as an alteration or even a weathering product. It cannot in this sense be called ""unconformable"" and thus arguments using the word in the accepted sense are invalid."

Jan 1, 1960

By Lindsay A. Robertson

The long term management of acid generating tailings at mine closure is a common issue, however, management of ARD is significantly impacted by local conditions, including climate. Acid generating tailings, over time, will produce acid rock drainage (ARD) if left exposed to water and air, which both contribute to the sulphide oxidation process. The long term closure of tailings storage areas is a concern from both environmental and engineering perspectives, with long term acid generation and dam stability the main risks. Several approaches can be taken to minimize ARD from tailings facilities using cover systems. Three tailings facility cover case histories, in areas of net positive water balances, were investigated using unsaturated flow modelling software to determine the long term potential for limiting ARD by increasing saturation of the tailings and decreasing oxygen ingress. Each case study demonstrates the importance of integrating the tailings dam engineering into tailings cover closure design. Model predictions are compared to measured saturation levels to assess the accuracy of the calculations.

May 1, 2011

By Terry Bachynski

_ Regulatory Process _ Approval Timelines _ Trends _ Stakeholder Consultation Expectation _ Challenges _ Initiatives for Regulatory Process Reform _ A Better Way? Alberta Regulatory Process _ Regulatory Approval of a major capital development requires multiple approvals from several regulatory authorities: ? EUB ? Decision Report approves development scheme and recommends conditions for other regulatory agencies ? AEnv ? approvals to construct, operate and reclaim required prior to any in field construction activity ? Federal - approvals for federally regulated activities ? Municipal ? Development Permit

May 1, 2004

By D. Milne

Laser profilometers exist for obtaining very accurate two and three dimensional profiles of joint surfaces. The application of this technology is not commonly applied to the collection of field data on discontinuity surface roughness. Rugged and portable field devices are not commonly used and the value of the possible field data that can be collected has not been well recognised. This paper reviews commonly used field techniques for assessing discontinuity roughness, discusses the value of this data and presents a new laser profilometer design for field application.

May 1, 2009

By S. Hon, C. Searcy, R. DasGupta, B. Fleet, A. Davidse, A. Pringle

"The mining industry is facing serious long- and short-term challenges relating to uncertain commodity prices, environmental pressures, and margin compression due to rising energy costs. Energy issues, formerly treated as an operating cost, are changing as executives search for longer term solutions to deal with uncertain fossil fuel prices and greenhouse gas emissions. Consequently, mining executives are increasingly willing to consider introducing a proportion of renewable energy (RE) systems into the mine energy mix. This paper examines how RE can be successfully integrated at mine sites, as well as some of the benefits and barriers to their wider adoption.RÉSUMÉ L’industrie minière fait face à de sérieux défis, à long et à court terme, en raison de l’incertitude des prix des matières premières, des pressions environnementales et des compressions de la marge bénéficiaire dues à la hausse des coûts de l’énergie. Les questions énergétiques, auparavant considérées comme un coût d’exploitation, changent alors que les cadres cherchent des solutions à plus long terme afin de prendre des mesures pour contrer les prix incertains des combustibles fossiles et les émissions des gaz à effet de serre. C’est pourquoi les cadres miniers sont de plus en plus disposés à considérer l’introduction d’une proportion de systèmes d’énergie renouvelable dans l’équation énergétique de la mine. Le présent article traite de la manière dont les énergies renouvelables peuvent être introduites avec succès aux sites miniers ainsi que quelques-uns des avantages et des barrières à leur application à une plus grande échelle."

Jan 1, 2015

By Xiao Huang, Jean-Francois Thibault, Ali Merati, Prakash C. Patnaik

Single-crystal nickel-based superalloys are the current state-of-the-art technology for the manufacture of turbine blades. This technological improvement of the turbine blade has brought a considerable increase in its cost. Repair and overhaul of service stressed single crystal turbine components is an economic necessity for life cycle cost reduction of engines since the cost associated with replacement is significantly higher than its counterpart polycrystalline component. This paper will first review the recently reported research in developing repair technologies used for DS and SX components. These techniques repair the crack or defect while at the same time ensuring that the mechanical properties do not deteriorate and, more importantly, that the single-crystal microstructure is not jeopardized. It will then be followed by a brief overview of the research conducted and initiated by the authors with regards to the repair of single crystal alloys.

Jan 1, 2004

By K. Morikawa, K. Asano, J. Yoshitomi

The quality requirements for ladle shrouds have become stricter year by year to the pursuit of higher productivity and improved quality in the continuous casting of steel. The ladle shrouds must be sufficiently durable under severe conditions, such as operation without preheating and during several sequential castings. The consideration is that ceramic fibres, which have been applied in shrouds for thermal insulation during casting, could pose a risk to the worker's health. We realized materials for the ladle shrouds which show high strength and low elasticity. At the same time pursuing effective insulation, a coating which contains no fibres (Foaming Coat) has been developed, replacing the conventional one containing fibres. These materials are durable under conditions of repetitive use and consequently satisfy the customer's demands. The ladle shrouds which were improved in this way have achieved an excellent durable life in hot service of three times that of conventional ones. This paper reports the recent technological developments in ladle shrouds as well as their performance under hot operating conditions.

Jan 1, 2004

By T. Navessin

Recent research activities in proton exchange membrane fuel cell (PEMFC) have significantly improved the performance per unit cost and its lifetime. These activities narrow the technology gaps, and thus, enable commercialization in some applications. One particular focus is in the development and understanding of proton conducting membrane materials. Many novel membranes are being developed which provide control and systematic understanding of complex relationships between chemical structure, morphology, physicochemical properties, and electrochemical kinetics. In this study, different classes of proton conducting membranes suitable for portable and automotive applications were evaluated in an operating PEMFC at the Institute for Fuel Cell Innovation, National Research Council. Analysis of these results may provide constructive feedbacks to the material researchers.

Jan 1, 2005

By E. Ferguson

In evaluating refractory designs for cast house applications, thermal calculations are frequently performed to determine cold face shell temperatures, temperature profiles and metal freeze plane locations within the refractory layer, and heat loss in the steady state condition. A problem arises when looking at molten metal transport crucible designs in that these structures are usually operating under non-steady state conditions throughout their production cycle. Because the molten metal temperature varies with time, and material properties such as thermal conductivity are temperature dependant, mathematical solutions are at best... complicated. This paper presents a relatively simple, iterative solution, that can be set up on a standard computer spreadsheet program, to calculate heat transfer in non-steady state conditions. These calculations can provide curves for (1) molten metal temperature vs time and (2) cumulative heat loss vs time, given variable starting conditions, to aid in the evaluation of molten metal transfer crucible refractory designs.

Jan 1, 2004

By F. Schulz

NA's primary smelter has continually increased its production output in the past decade, making it necessary to improve the lifetime of the casting moulds for copper anodes. The current throughput of more than 1,100,000 tonnes per year of copper concentrates amounts to an output of about 450,000 tonnes per year of anode copper at NA's Hamburg plant. The anodes are cast on a single casting wheel with 24 anode moulds. Besides the stable chemical analyses, the reproducible geometry of the anodes is an important precondition for the success of the subsequent electro-refining process. The anode moulds are subjected to thermally-induced alternating stress and side reactions with the melt. Typical signs of wear will be shown and discussed. Different processes to produce anode moulds will be introduced and the results in terms of their lifetime and the quality of the anodes themselves will be discussed. Finally an outlook is given on possible efficiency improvements.

Jan 1, 2007

By D. Laguitton, D. Cimon

"BILMAT is one of the most powerful algorithms in existence for material balance computation in mineral processing flowsheets. It is based on a hierarchical decomposition coupled with the Lagrange multipliers method widely reported in the literature. Flowrates can be calculated optionally for pulp, solid or water. Assays are adjusted for a variety of subnetworks, such as assays of the solid as well as assays of fractions of the solid called level 4 data (l: pulp, 2:solid and water, 3:assays of solid, 4:assays of classes of solid).BILMAT4 is a new implementation of BIU1AT that operates in a new microcomputer environment and makes the method more accessible than ever. Its main features are a full-screen colour editor allowing graphic flowsheet drawing and data entry with automatic error checking. Mass balance equations are automatically generated by analysis of the graphics and corresponding data, thus relieving users from the error-prone definition of networks. Sensitivity analysis is performed to assess confidence intervals of computed flowrates and adjusted assays.BILMAT4 incorporates an option for gold leaching circuits where the element to be balanced appears in both the solid and liquid phases with negligible effect on the mass flows of solids. Recoveries are computed in all streams. This program is currently released by CANMET as part of the CAMP collection for Computer Aided Mineral Processing. A complete sample run of the program is discussed."

Jan 1, 1989

By D. Y. Kim

This paper shows an approach that a gondola-typed robot recognizes walls on building facades. It is applicable for autonomous or teleoperated building façade painting robots. The robot may react based on the wall classification data. This approach is based on 2D LRF(two-dimensional Laser Range Finder). The robot acquires relative distances to walls, and a Kalman filter decides correspondence of walls. An ARS(Attribute Reference System) sensor helps convert LRF coordinate to global coordinate. The experimental results demonstrate the conversion of LRF data.

Aug 1, 2013

By Juan C. Sotomayor Álvarez

The Huantajalla mine is seated on Uchucchacua 's Mixing District that is the fourth producer of Silver in the world. Huantajalla Mine is a new mine that nowadays is being explored and recently it has began to operate. The project for 4-A vein exploitation in Huantajalla Mine using Longhole drillings as a new method of mixing is developed by Planning Department of Uchucchacua Mine in coordination with Geology Department of this mine, started in June 2004. This project is funded by Company of Mines Buenaventura S.A.A In July 2002, Geology Department started the exploration on the area of Huantajalla Mine, discovering the 4-A vein. The reconnaissance and definition of the vein finished June 2003, finding 79,080 Ton of mineral of Silver with a grade of 40.0 Oz Ag/ton and a thickness of 1.85 meters (6 feet ). Using the longhole method on the vein exploitation will replace the cut and fill and shrinkage methods, and it will keep a dilution of 15%.

Oct 1, 2004

By D. Xia

Pt-Bi intermetallic Nanoparticles was prepared by the polymer-anchor method. The electron micrographs shows that the dimensions of particles sharply distribute in the range of about 3-6 nm. The elemental ratio of Pt/Bi in the bimetallic particles is estimated by the electron probe microanalysis method. Pt-Bi intermetallic Nanoparticles shows a higher activity for the ORR than pure Pt. No significant dependence of the oxidation currents on the rotating speed of the electrode could be observed in the presence of methanol. This clearly indicates that the Pt-Bi is inactive to methanol.

Jan 1, 2005

The Rabbit Lake In-Pit Tailings Management Facility contains frozen layers of tailings due to subaerial deposition during the coldest periods of winter. Thawing is required to ensure full consolidation of the tailings and to regain disposal space presently occupied by ice. Electric resistance heating has been used to heat soil for bitumen extraction and remediation of volatile contaminants. A preliminary evaluation of the application of electric resistance heating to thaw about 0.3 cubic metres of frozen tailings was conducted using tailings frozen at about -2 oC. Visible thawing of the tailings mass was observed after 25 hours, demonstrating the feasibility of this approach.

Aug 1, 2010

By V. C. Pandolfelli, P. Bonadia, F. A. O. Valenzuela, L. R. Bittencourt

Refractories for aluminum cells, if not properly selected, can lead to increased energy consumption and even shorten the pot life. Based on recent advances in understanding the deterioration mechanism of cathode materials, several commercial bricks in the SiO2-Al2O3 system were compared to the one used by an Alcoa smelter. Both physical and chemical properties were considered in the selection of the refractories. A more reliable method of permeability measurement, which takes into account inertial and viscous effects during the fluid flow, was applied. Additionally, the traditional cup test and other characterization techniques, such as thermal conductivity, X-ray diffraction, and mercury porosimetry, indicated that a brick with a relatively low alumina/silica ratio, presenting low open porosity and low permeability, far exceeded the performance of the brick currently in use.

Jan 1, 2004

By Simon D. Handelsman, Malcolm Scoble, Marcello Veiga

"Abstract - In many mining areas, potentially profitable mineral projects can be at risk because local people do not trust their governments and mining companies on many issues, including human rights. Projects will continue to be vulnerable to potential failure, delays, and higher costs. This paper suggests that geoscientists need to be aware of the global challenges they face from issues of corporate social responsibility, sustainable development, and human rights. These are not areas in which geoscience education has traditionally focused.This paper examines the types of conflict concerning human rights that are encountered by geoscientists involved in mineral exploration and development. It provides a background to human rights issues and presents a classification of the types of issue encountered. It reports on a survey of case studies that provide examples of the breadth, complexities, and consequences of such issues. The paper then concludes by outlining the development of codes and standards to improve performance, and suggests approaches for positive, practical engagement."

Jan 1, 2003