Search Documents

By James A. Barr

When phosphate mining operations first commenced in Tennessee the loss of both high- and low-grade material was large, because of the crude hand methods employed. Practically all rock smaller than 2 in. was thrown back into the pits and covered with the overburden of subsequent openings. With the advent of mechanical washers and other mining machinery, together with the abolishing of the contract system, the waste has been steadily diminished, until at present only the finest sand is being rejected; and even this is not lost, for in the majority of cases the water, slime, and sand from the washers are run into large settling ponds where practically all of the phosphate-bearing material is caught and stored for future use, or until it is profitable to ship lower grades. The latest equipment used to recover the fine and lower-grade phosphate sand includes Dorr thickeners, settling tanks, Dorr classifiers and settling ponds served by locomotive cranes with clam-shell buckets, making it possible to save material averaging as fine as 200 mesh. TO attempt saving finer material would necessitate a different type of drier, which might be patterned after the multiple-deck roasters. The present tailing runs from 15 to 25 per ccnt. of available phosphate, which, howrever, as mentioned before, does not represent a total loss to possible future operations. The demand of the consumer is the greatest factor in regulating the recovery at present. In the mining of blue rock, which does not require washing treatment, the main waste material is the capping of low-grade kidney formation, generally used for backfilling of the rooms. By reason of the introduction of improved methods in the early stages and the re-mining of territory skimmed over at the start, at the present time the net result of all operations is a comparatively small loss. One of the largest temporary losses in the industry occurs in the Florida pebble district where the recovery of phosphate runs about 25 per cent. The loss is classed as temporary because most of the tailing has been collected in ponds and piles, where it may be reclaimed in the future should developments or improved processes warrant. In cleaning the Florida pebble phosphate, aside from the elutriatisn

Jan 1, 1916

By J. D. Ridge

The geologic setting and mineral relationships of seven European massive sulfide deposits that more or less conform to the bedding of the largely noncal-careous sedimentary rocks and/or bedded volcanics in which they are found are considered here. These orebodies consist largely of massive beds or lenses of sulfides usually surrounded by halos of disseminated sulfides and distorted by tectonic activity. The formations containing these deposits have been metamorphosed in varying degrees at times subsequent to their lithification. The ore-forming process is thought to be essentially volcanic, with the ore constituents being brought to the shallow-water site of deposition through tectonic fissures from magma chambers at depth as gases or relatively concentrated hydrother-mal solutions. Certain European ore deposits of base metal sulfide have previously been considered to be of hydro-thermal or magmatic origin, but today a number of European mining geologists consider them to be syngenetically produced. In an effort to provide American geologists with some idea of the reasons behind this change in thought, the geological settings of seven of these deposits have been studied. These are: Ldkken, Meggen, Rammelsberg, Ergani-Maden, Outokumpu, Boliden and Roros. These deposits lie in bedded rocks that have undergone metamorphism from causes not universally agreed upon; most of the formations were originally shales, and may have been intercalated with limey and occasionally quartzitic beds, volcanic tuff, agglomerate, extrusive lavas and usually basic intrusives. Deposits of the conformable type, however, are not confined to these rock types but may be in calcareous and associated igneous rocks or almost entirely in volcanics. These deposits may be closely associated in space with igneous rocks that, again, are usually basic types. Although the ages of the enclosing rocks range from mid-Precambrian (Boliden and Outokumpu) to Eocene (Ergani-Maden), the bulk of them are Paleozoic, with two (Meggen, and eammelsberg) being upper middle Devonian and two (LØkken and RØros) being Cambro-Ordovician. Geographically, two are in West Germany, four in Scandanavia and one in Turkey. Of the seven deposits, six are mined for copper, with three of these also producing zinc, and two lead; one is mined for zinc and minor lead. In the discussions of the seven conformable deposits that follow, I have attempted to present as uniform a treatment as their varying characters will permit. For each deposit, I have considered the stratigraphy of the area, its major structural characteristics, the form of the orebodies, their mineral content, and the origin of the ore. In the last of these subdivisions, I have presented only the viewpoint of those who believe the ores to have been formed by syngenetic processes, processes that went on at the same time as those which produced the beds that enclose the ores but that are not, in the deposits in question, thought to have been sedimentary in the strict sense of the term. The materials of which these orebodies are composed, it is suggested, did actually collect by falling through sea water to the floor of that portion of the sea in which they accumulated. The ore constituents, however, are believed by a considerable number of European geologists to have been added to the sea water from intratelluric sources, probably igneous magma chambers, as exhalations — hydrothermal solutions or volcanic gases. The effect of the encounter with sea water on these ejected gases or water-rich vapors was to precipitate their potentially solid constituents with great rapidity; they were deposited so quickly, in fact, that the amounj of normally accumulated mechanical or chemical sediment deposited over the same period of time was essentially negligible. The ores formed in this manner, however, are generally interbedded with normal sediments or with lava flows, or with any combination of these two types of rock-forming materials. Such departures as these deposits may have from their original mineral content and attitude are thought to be directly related to the degree of dynamic or static metamorphism that they may have undergone after their accumulation. I have not attempted here to present alternate hypotheses to that of so-called exhalative sedimentation although, of course, such exist and, in my

Jan 1, 1963

By J. D. Embury, R. M. Fisher, A. S. Keh

An investigation of the defect structure and properties following large strain deformation has been carried out using transmission electron microscopy and mechanical testing for a range of ferrous materials and for copper. It is shown that, for a variety of ferrous materials, a cellular substructure is developed during the initial stages of working and on further deformation the dimensions of this substructure are reduced. Quantitative measurements of the flow stress and the scale of the substructure indicate that the strength of heavily worked materials is largely determined by the spacing of cell walls. These cell walls act as dislocation barriers in a manner analogous to grain boundaries. FCC materials do not harden as extensively as bcc after cold working and the present observations on copper indicate that the dimensions of the substructure in fcc materials are not markedly reduced on deformation. The differences between the fcc and bcc structures produced by large plastic strains are ascribed to differences in the extent of dynamic recovery. It is tentatively proposed that the greater stability of substructural barriers in bcc structures results from strong interstitial Pinning effects. It is proposed that for large plastic strains the work-hardening process may be considered in terms of the reduction of substructural-barrier spacing during the working process. This pvovides a simplified hut useful analysis of the strain hardening occurring during mechanical processes. THE mechanisms of strain-hardening processes have occupied the attention of numerous investigators over the past three decades and a multitude of theories have emerged in this field. The majority of previous work has been concerned with the development of a description of the plastic behavior of single crystals in terms of dislocation theory.'" In contrast, scant attention has been given to the strengthening mechanisms operative during mechanical working processes such as rolling and drawing. The large plastic strains involved in these processes make it difficult to correlate the observations with any elementary dislocation theory. Further, as Bullen and coworkers3 have opined, for large plastic strains both hardening and recovery occur simultaneously and thus it is extremely difficult to estimate the effect of plastic strain on the ambient internal stress field. It is probable that for large plas- tic strains any theoretical estimate of the internal stress field must be made in terms of complex dislocation groups. Although some valuable theoretical work has been done toward calculating the elastic properties of dislocation groups4 any detailed self-consistent model for large plastic strain is as yet impossible. With these limitations in view it is still of value to examine the mechanical properties of highly strained materials as a function of their substructure. This relationship is explored in the present communication for a variety of materials subjected to rolling, drawing, or swaging. The primary object of this investigation has been to establish the validity and the limitations of the substructural strengthening mechanism proposed by Embury and eisher' for drawn pearlitic wire and by Meieran and Thomas for drawn tungsten wire. No attempt has been made to delineate the basic interaction mechanism which occurs between a slip dislocation and the substructure and the authors believe that a great deal more experimental evidence must be compiled before these fundamental aspects can be explored. Also, no specific attention has been given to the detailed formation of substructure during working. Experimental Details. A variety of materials were used in this investigation, the compositions and heat treatment of which are tabulated in Table I. The commercially pure iron is referred to throughout this report as Ferrovac E. The mechanical working processes were all performed at room temperature. The wire drawing was performed on a manual drawing bench. Reductions of between 10 and 20 pct in area per pass were used in both swaging and drawing. The experimental parameter used to evaluate the mechanical properties of the materials was the 0.2 pct proof stress. This was determined for wire samples using an Instron tensile machine at a crosshead speed of 0.02 in. per min. The techniques for preparation of samples for transmission electron microscopy have been described previo~sl~.~ Specimens from wire samples were prepared from longitudinal sections and in some cases from transverse sections. To evaluate the substructural characteristics of rolled materials, thin foil samples were prepared of both the face and edge sections. Results. One of the more familiar ways of expressing work hardening in mechanical working is by the flow stress as a function of reduction in cross-sectional area. Fig. 1 shows such a plot for Ferrovac E eutectoid carbon steel and for copper. The curve for Ferrovac E is characterized by an initial stage of rapid work hardening and a final stage of rapid work hardening separated by an intermediate stage with a low rate of work hardening. This behavior is typical of many ferrous materials and the drawn pearlite wire previously investigated by Embury and Fisher is a more pronounced example. Copper shows an initial

Jan 1, 1967

New York Meets first Wednesday after first Tuesday of each month. DAVID H.-BROWNE, Chairman, JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE, Secretary, 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. . ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia Holds four sessions during year. Annual meeting in September or October. FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 11, 1915

Rep. William S. Hill (R.- Colo.) will preside over a Congressional hearing investigating the problems of the mining industry to be conducted in Phoenix, Ariz., late in April. Rep. Hill has expressed the desire to hear from the industry itself all possible testimony on the needs of domestic mining and how Congress can help. Rep. John J. Rhodes of Arizona is also expected to attend the hearing. Two new features are incorporated into an SO2 process for treatment of low grade manganese ores disclosed by Chemical Construction Corp. The new approach includes a high temperature autoclaving step and a sintering operation. Data was given for work performed on Cuyuna Range ores.

Jan 4, 1953

By M. H. Richman, W. D. Sproul

THE indexing of a field-ion micrograph is in many cases similar to the indexing of the poles of a stereo-graphic projection.* If one has a standard projection as a guide, the task of indexing is relatively simple. In this way, field-ion micrographs of bcc and fcc wires have been oriented from projections available in most any text on X-ray diffraction. These books always illustrate the projections for the bcc and fcc structures and even for a particular hcp structure. There is no "standard" hcp projection because the angles between planes depend on the c/o ratio of the unit cell. In order to index field-ion micrographs of hcp metals, one must compute the angles between various planes—a rather laborious task. In recent work,, we have had to identify the structure and index the orientation of field-ion micrographs of the compounds WC and W,C. To overcome the problem of computing angles by hand or calculator, a program was written in Fortran lV for use on the IBM 360, Model 50 which will compute all angles between planeswith indices (hlklll) and (17,k,l2) in the range from (447) to (444) for any given c/o ratio. The program, which is more specific than that of Camp and clum, was so written as to take advantage of the multiplicity of the hexagonal system, and, for the limits defined above, only 26,649 values out of a possible 265,721 values had to be computed. This is a 90 pct saving in time (and cost) and was accomplished in the following way. Because the lattice parameters of the hexagonal crystal system are defined such that: a = b * c [1] the I index does not enter into the multiplicity (i.e., it cannot be transposed with the h or k indices), and all possible values of h and I, from 4 to 4 must be used—a total of eighty-one combinations. The index h2 varies the most—it must assume values from - Ill,: to 3Ihl. The indices kl and k2 are always equal and vary

Jan 1, 1969

By A. B. Bowman

The 1963 Jackling Award lecturer describes the founding of Banner Mining Co. and its trials and tribulations before becoming an established firm. Such aspects as geological description of Banner mining areas, history of exploration and production, areas of present interest to the company and research work conducted by the company are included. Several years ago a wealthy Chinese business friend of mine purchased an interest in a proposed oil well to be drilled a great distance from his home. A few months later it came in as a producer and proved to be a huge success and materially added to his resources. I asked him why a man of his wealth should be so lucky in a venture outside his sphere of knowledge when most people of modest means never seemed to get ahead. His answer was, "Fat Hoy takes a chance." Even though this was his answer, I knew from my association with him that there were other tempering considerations which Mr. Hoy applied before making up his mind to enter any transaction. First, he was a cautious individual. He was also a great believer in details and insisted on knowing everything possible about a situation, and finally, he was what we call a very solid individual with good basic instincts and judgment. This philosophy of Mr. Hoy may be applied to most any business but especially to those engaged in a search for natural resources such as mining where great risks are involved. This article concerns events in the history and growth of Banner Mining Co., with which I have been associated for 27 years in capacities from mine surveyor to vice president. Mr. Hoy's philosophy has played a significant role in the exploration projects of this company over the years, but what is more important, the officers, directors, and controlling interests in Banner have been aggressive in their search for ore reserves. THE BIRTH OF BANNER Banner Mining Company was incorporated in September 1935 by a group of Oklahoma and Texas oil men for the purpose of exploring and developing the Bonney-Manilla mines at Lordsburg, N.M. These properties had a history of intermittent production since the first ore discoveries as far back as 1870. Most of the production from the district has come from four mines, namely, the Eighty-Five, the Atwood, the Bonney-Manilla, and the Misers Chest. The last two are now owned by Banner Mining. The Eighty-Five mine operated between 1885 and 1931, and production totalled 1,494,287 tons averaging 0.11 oz of gold per ton, 1.23 oz of silver per ton, and 2.80% copper. The vein extended for a distance of about 3000 ft northeast and was mined to a depth of 1650 ft. The Atwood mine, adjoining the Eighty-Five mine, to date has been of lesser importance as a producer, but it has been operating for several years producing high silica flux ores for a smelter. Production totalled 352,828 tons up to January 1, 1962 From the Bonney-Manilla and Misers Chest mines, owned by Banner, production through 1961 totalled 2,006,343 tons with an average grade as mined of 0.0192 oz of gold per ton, 0.760 oz of silver per ton and 2.63% copper. Banner built a 150-tpd flotation mill in 1936 after almost a year of development on the 600 level of the Bonney mine. After less than one year's operation, it became apparent that the 150-tpd rate was not sufficient to make a reasonable profit due to the marginal grade ores. The low tenor of the ore, mainly chalco-pyrite in a highly siliceous gangue, made mandatory the close control of costs in order to make ends meet. A 300-tpd unit was added to the mill in 1937, and it is still the operating unit today. The clean sulfides presented no problems in milling. A metallurgist doing research on it at the time stated that the copper minerals seemed to have a built-in desire to float. Mill recovery of copper throughout the 27 years of operation has averaged 96.23%. A PERIOD OF FORCED GROWTH World War II brought many hardships to Banner. Labor and supply shortages caused drastic curtailment in development work. Rapidly rising costs far outdistanced any relief from pegged prices which we received from Government agencies. Finally, a branch of the Government asked us to stop all devel-

Jan 1, 1963

By Albert J. Phillips

IT is a privilege and a pleasure to deliver this, the Twenty-sixth Annual Institute of Metals Division Lecture. Eleven years ago C. A. Edwards addressed this audience on the subject "Gases in Metals." In spite of this relatively recent presentation, I propose to, present to you some quantitative considerations of industrial significance on the separation of gases from molten metals because recent observations and measurements, presented in the literature, have made it possible to evaluate mathematically the gases or gas-forming elements and to develop an understanding of the mechanism of gas separation that should permit, in many cases, the control of this baffling phenomenon. DEFINITIONS Before becoming involved in the subject it seems desirable, for the sake of clarity, to state certain definitions and axioms: I. We are dealing only with gases that separate from the molten metal either during cooling or in the transition from liquid to solid. Gases injected by the liquid stream and trapped in the solidified metal, or those forced into the solidifying metal from the mold due to either thermal or cher4ical effects are not considered. Neither are we concerned with the separation of gases within the metal after solidification is complete for the data on this subject are at least complete enough to permit the practicing metallurgist to satisfactorily control the phenomenon. 2. Only where there is a decrease in solubility or a change in equilibrium of either a gaseous element or an element that reacts to form a gaseous compound, can there be a separation of a gaseous phase from the liquid or solidifying metal. 3. The amount of gas separating from the liquid during solidification can be computed directly from the amount of the element contained in the liquid when freezing commences less the amount of the element found in the solid either as a separate solid phase or in solid solution. 4. There can be no separation of gas bubbles unless the told pressure of the gases in the liquid meld exceeds atmospheric pressure plus the hydrostatic pressure of ' the liquid metal head. (In addition, pres- sure resulting from surface tension in- creases the total pressure requirement for initial gas separation. Probably the remarkable differences in appearance caused by different gases in the same host metal are influenced greatly by the rate of diffusion of the gas in the liquid metal balancing the decrease in pressure as the gas bubble size increases and the surface tension effect decreases. Thus hydrogen with its high diffusion rate in liquid copper separates in the form of relatively coarse cavities for a given rate of heat extraction.) 5. Gas separation can take place at less than atmospheric pressure in the voids created by the shrinkage from liquid to solid, but since the voids are not caused by the gas the presence of gas in the voids is of importance only where it

Jan 1, 1947

By R. S. Busk, R. F. Marande

The magnesium-aluminum-zinc 'system contains most of the magnesium-base alloys used commercially, although in practice the ternary alloys are usually modified by the addition of a small amount of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the obiect of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.' All alloys reported were made in rj-lb. melts, superheated to r700°F. for 15 min., cooled to r400°F. and poured in sand molds. The test bars produced had a 1/2-in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. Constitutional Data Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By R. F. Marande, R. S. Busk

The magnesium-aluminum-zinc 'system contains most of the magnesium-base alloys used commercially, although in practice the ternary alloys are usually modified by the addition of a small amount of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the obiect of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.' All alloys reported were made in rj-lb. melts, superheated to r700°F. for 15 min., cooled to r400°F. and poured in sand molds. The test bars produced had a 1/2-in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. Constitutional Data Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By AIME AIME

IN a recent technical paper of the Central Committee of the French Coal Mines (Note technique No. 198, by L. Lahoussay) the author points out that continuous in¬crease in depth of mine shafts makes it more and more necessary to look for appropriate means to reduce the weights and dimensions of the hoisting ropes. Increasing depth demands a larger section and weight for the cable if the useful load is not to be cut down at the same time. This naturally leads to increased cost per ton, and at the same time creates serious mechanical difficulties. The dimensions of the hoisting engine must be increased, acceleration at the start must be decreased so as to avoid periods of excessive peak power loads, and a longer time be allowed to slow down the speed of the hoist when applying brakes. The hoisting rope, upon which depend the dimensions and hence the mass of the hoisting engine, presents the greatest obstacle to the development of hoisting from greater depths. Evidently, for a given depth, the total weight of the rope can be notably reduced by utilizing a wire rope of decreasing section, approaching the theoretical logarithmic form. This is a solution frequently adopted for great depths. Of course, the weight of the rope could be easily' diminished by reducing the useful load, but it is certain that with increasing depth of mining, more effort must be made to confine the hoisting to a small number of shafts, and increase the load hoisted per trip.

Jan 1, 1933

By George Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro-posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bitu-minous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O'Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various Winds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

By Reginald E. Hore

Since the discovery of silver at Cobalt, Ontario, in August, 1903, more than 100,000,000 oz. of silver have been produced by the mines in the Nipissing district, and there is reason to believe that at least as much more will be produced in the nex five years. The estimated value of the aggregate output o ore to the end of 1910 is $48,327,280. The ore yielded 93,977,833, oz. of silver and was mined at a net profit of abou $16,000,000. For 1910 the production was 30,558,825 oz., valued at $15,436,894, and yielding a profit of about $9,000.000. The details of the production of the Cobalt district for the years 1904 to 1909, inclusive, as reported by the Ontario Bureau of Mines, are given in Table I. The shipments from Cobalt are in the form of smelting-ore, concentrates from milling-ore, and bullion. The smelting-ore is largely high grade, averaging about 3,000 oz. per ton A smaller return is from what is called low-grade ore and which

Jan 1, 1912

By J. Szekely, J. W. Evans

A formulation is given for radiant heat loss from the surface of molten steel held in a ladle and numerical solutions are presented for the resultant integrodif-ferential equations. The results are shown on plots of the net rate of heat loss against time, with the geometlry, emissivities, thermal properties of the walls, and Preheat as parameters. It was found that the rate of the vadiant heat loss from the exposed metal surface was comparable to the conductive losses from the Portion of the metal in direct contact with the walls. The radiant heat loss was markedly affected by the geometry and by the thermal properties of the walls the net radiant heat loss from the steel could be drastically reduced by providing a top cover and also by the provision of preheat. The results of this work are thought to be relevant to heat loss calculatious concerned with vacuum degassing and with operatzons in which molten metals are held in ladles. WhEN molten steel is held or transferred in ladles heat losses inevitably occur. The accurate assessment of these heat losses is of importance in process design considerations, as the temperature of the metal may have to meet rigid specifications in certain stages of the processing sequence. As shown in Fig. 1, the principal mechanisms responsible for heat loss are: i) Conduction into the walls and ii) Thermal radation from the top metal surface (possibly augmented by natural convection) The conductive heat loss may be readily calculated as much information is available in the literature on both the general theory1'' and on its particular applications to ladle heat loss calculations. Evaluation of the radiant component of the heat loss is less straight-forward. In two recent papers it has been shown that the presence of a slag layer 2 to 3 in. thick would prevent any significant heat loss for periods up to an hour,5'" however, should bare metal be exposed, constituting the radiant surface, substantial heat losses could occur. This latter case is of considerable practical interest in various degassing operations and in the vacuum processing of certain specialty steels, where the top surface of the metal is not covered by a protective slag layer. Under these conditions a substantial radiant flux is emitted by the top metal surface; part of this flux leaves the system, part of it falls in the ladle walls. The radiant flux incident on the ladle walls is in part absorbed and conducted away, and in part reflected and re radiated. The purpose of the paper is to present a general formulation of the problem, the resultant solution of which should enable computation of the net radiant heat loss from the metal surface. The principal variables, the effect of which will be investigated, include initial metal temperature, geometry, thermal and radiative properties of the wall, and various modes of preheat. FORMULATION Consider a cylindrical enclosure, shown in Fig. 2, with a diameter D, height H, and wall thickness W, the cover at the top of the cylinder having a wall thickness L. If the temperature of the base (representing the top surface of the metal) is kept constant, say, Tb, the problem is to calculate the net rate of heat loss from the base as a function of time, geometry, the initial temperature distribution, and the thermal properties of the system. As customary, the formulation will consist of the mathematical statement of the conservation of thermal energy within the system.

Jan 1, 1970

By Thomas Watson

INTRODUCTION THE users of barite in the United States derive their supply partly from the domestic production and partly from the imports from foreign countries. According to the Mineral Resource division of the U. S. Geological Survey, the domestic production of barite in 1913 was 45,298 short tons, valued at $156,275, or $3.45 a ton, and the imports of crude barite were 35,840 short tons, valued at $61,409, or $1.71 a ton. These figures clearly show a decided advantage in cost of the foreign over the domestic barite to users in the United States. The difference in cost is the only advantage to the consumer of foreign barite, for there are large reserves of the mineral in the United States of good grade. The production of many of the operating mines is capable of decided increase, and it is believed that the operating mines together with the large reserves of undeveloped deposits of barite are entirely adequate to meet the demands of the users in the United States. Deposits of barite are known in California, Idaho, Nevada, and Alaska, but most of them are undeveloped because there is, apparently, no market for the .material in that region. The domestic production is derived from Missouri and the Appalachian States, the greater part being obtained from Missouri. Following the outbreak of war in Europe many users of foreign barite in the United States have been forced to seek their supplies at home. It seems opportune at this time, therefore, that a general review be given of the barite industry in the Appalachian States, one of the two areas from which the domestic supply of the mineral is derived, and that attention be directed to the undeveloped deposits in the region. Briefly, then, this paper reviews the barite industry in the Appalachian States, and describes the occurrence, preparation, and uses of the mineral.

Jan 2, 1915

Executive Committee, Board of Directors Augustus B Kinzel, Chairman, J L Glllson, Vice-Chairman, A W Thornton, Howard C Pyle, Grover J Holt Finance Committee, Board of Directors Andrew Fletcher, Chairman, J S Vanick, Gall F Moulton Investments Gail F Moulton, '60, Chairman, Henry Krumb, '59, J Loveloy, '61, C R Dodson, ex off as Treasurer, Andrew Fletcher, ex off as Chairman, Finance Com¬mittee Endowment Andrew Fletcher, Chairman, N G Alford, H DeWitt Smith, W J Coulter, J V N Dorr, R B Gilmore, J B Haffner, O H Johnson, D H McLaughlin, J R McMillan, L F Reinartz, C E Weed, Wilfred Sykes, J R Suman Honorary Memberships H DeWitt Smith, '59, Chairman, C E Reistle, Jr, '59, Grover J Holt, '59, L F Reinartz, '59, M L Haider, '60, D H McLaughlin, '61, John M Lovejoy, '62, Augustus B Kinzel, ex off as President

Jan 1, 1958

By T. Lane Carter

It is a curious fact that while in our Transactions there are papers dealing with mining-districts in all parts of the world, in Europe, Asia, Africa, and Australia, there is not one which describes the mining possibilities of Nicaragua, our near neighbor. To be most interested in distant objects, like the moon, and to neglect what lies at our feet, appears to be a trait of human nature. The neglect of Nicaragua is not confined to the American Institute of Mining Engineers. In no other transactions am I able to find papers dealing with mining in Nicaragua, some parts of which are as much in need of discovery and research as the North Pole. I hope this paper will be the precursor of many others to be printed in our Transaclions, dealing not only with the miniilg possibilities of Nicaragua, but with the whole of Central America, where there are vast areas a,waiting skill and capital for their development. Much of this capital and skill should come from the United States in the future, although it is probable that European capitalists, when they appreciate fully the possibilities, will investigate more and more the mining-resources of Nicaragua and ot'her Central American republics. Fig. 1 is a sketch-map of Nicaragua showing the principal mining-districts. 11. History. Mining in Nicaragua did not begin yesterday. It was commenced by civilized man when the Spanish conquerors pene-' trated into the interior and forced the natives to procure the precious metal for them. It is strange that the Spaniards did not find more gold, and work on a scale as extensive as in Colombia and other parts of South America. Probably in Nicaragua the Indians covered up most of the rich prospects

Jan 1, 1911

By J. W. Hickman

Most of the electron diffraction studies of oxide films which form on metals and alloys have been carried out by oxidizing the specimens in an auxiliary furnace, cooling down to room temperature and then inserting the sample in the camera and taking a diffraction photograph. Prior to the investigations at the Westinghouse Research Laboratories, no systematic study of the oxidation of any metal or alloy had been made over a wide temperature range with photographs taken at elevated temperatures except the investigation of iron by Jackson and Quarrell.' In order to interpret the electron diffraction patterns of the oxides which may form on alloys, it seemed advisable to make a comprehensive study of the oxidation of the purest metals available in the bulk form. Thus far studies have been completed on iron,2 cobalt,~ nickel,= chromium,= copper,z tungsten,s molybdenum,3 beryllium,' uranium,' thorium,' titanium6 and zirconium6 while investigations are in progress on tantalum and columbium. The next step in the study is concerned with the investigation of the oxides which form on binary alloys. Some of the alloys consist of a single phase while others contain more than one phase. The identification of the oxides on the surface of a binary alloy may be more difficult than on the metals since oxides containing both metals as well as those of each metal separately may form. Furthermore, it is possible that solid solutions of the various oxides may occur. In these cases the electron diffraction method may not be able to identify the oxidation products unequivocally. Examples of solid solutions which may present difficulties are MOO* and WOp, Fe304 and FeO.CrnOa since the diffraction patterns are so similar. Since electron diffraction can determine only the structure of the oxide, the chemical composition must be inferred from the diffraction data based upon X ray diffraction investigations of specimens of known composition. It is possible in some cases to decide whether a given solid phase reaction can occur on the surface of an alloy by a study of available thermodynamic data. Table I lists the equations for the formation of most of the oxides from the elements together with values of loglo Kg for the several temperatures. AF"B = -RT In KR AF°R and KR are the free energy and equilibrium constant of the reaction. Calculations may be made using the the given in I 1 to determine whether a given solid phase reaction is possible thermodynamically. For example, a solid phase reaction should occur between aluminum and chromium oxide to form

Jan 1, 1949

Rossiter Worthington Raymond, Ph.D., LL. D-1840 to 1918.-Dr. Rossiter W. Raymond, Past President, Honorary Member and Secretary Emeritus, died suddenly of heart failure at his home, 123 Henry'St., Brooklyn, N. Y., on the evening of Tuesday, Dec. 31, 1918. He was one of the founders of the Institute and its second President. A Memorial 'Service will be held on Monday afternoon, Feb. 17. James Douglas.- The Institute suffered a second very severe loss by the death of Dr. James Douglas, Honorary Member, Past President (having served as President for two years), and in three separate respects the greatest benefactor of the Institute: first, in raising funds by volun¬tary subscription and his own personal gifts to pay the Institute's share of the money owed on the land on which the Engineering Societies Build¬ing now stands; second, as original donor to Engineering Societies Library; and third, by his bequest of $100,000 for the maintenance of the library of the American Institute of Mining Engineers. A resolution regarding the death of Dr. Douglas was passed by the Board of Directors and at the meeting of the Institute on Sept. 4, 1918, in Colorado, at which time a memorial service was held in the thea¬ter of the Hotel Broadmoor, attended by about 400 members and guests. A copy of the resolution was prepared and sent to the family. A bronze tablet is now being prepared and will be placed in the Members' Room and unveiled at the February meeting. A biography and portrait of Dr. Douglas was published in the September, 1918, Bulletin. There is also placed in the Engineering Societies Library an oil portrait of Dr. Douglas which had his own approval and was presented by him. American Institute of Metals.--During the Spring of the year, plans were completed with the American Institute of Metals whereby this society became the Institute of Metals Division of the American Insti¬tute of Mining Engineers. This body was a dignified aggregation of metallurgists which had been in existence for about 11 years. A bronze tablet commemorating the American Institute of Metals is now being placed in the Members' Room of the Institute, and during the year 1919 the Bulletin will bear the following title: "Bulletin of the American Institute of Mining Engineers, with which is consolidated the American Institute of Metals." Visits to Local Sections.-During the year President Jennings made visits to six of the Local Sections, on three of which occasions he was accompanied by the First Vice-president and the Secretary. First Vice-president Goodale made five visitations and the Secretary made eight.

Jan 1, 1923

By DR. DOUGLAS

Discussion of the Paper of Dr. Douglas, presented at the Toronto Meeting of the Institute, July, 1907 (Trans., xxxviii., 455 to 471). EDGAR HALL, Silverspur, Queensland, Australia (communication to the Secretary*) :-Dr. Douglas has written on this subject before, and his influence has had a powerful effect on the side of freedom among the younger generation of engineers. Moreover, it is not the first time that he has attributed the decline of the copper-smelting industry in Swansea to the secrecy maintained by the firms there engaged in smelting-operations. In this latter statement I think his conclusions are open to criticism. Whether the firms referred to have suffered by their secrecy is their own business-I. bold no brief for them ; but that the decline of the copper-industry at Swansea was inevitable seems to me to be proved conclusively by Dr. Douglas's own writings. In his paper on The Copper Situation,1 Dr. Douglas says "In comparing iron and copper mining, . . . it must be remembered that 2 tons of average iron ore from the most prolific source now available will make 1 ton of metal; whereas from 33 to 75 tons (say an average of 50 tons) of copper ore must be mined to produce 1 ton of copper." And further: "Last year's production of iron was made from approximately 50,000,000 tons of ore. Our copper mines, to yield a production of 900,000,000 pounds, must have handled approximately 22,000,000 tons of ore, or nearly half the quantity raised from our iron mines." Is not this the key to the whole situation ? In transporting the 50,000,000 tons of iron-ore, 25,000,000 tons of the metal iron were carried so much nearer to the market, but the transportation of 22,000,000 tons of copper-ore would have carried only 450,000 tons of the metal copper nearer to its ultimate destination. The small percentage of copper available in its ores makes

Sep 1, 1908