Search Documents

By John T. Galey

Production of crude oil for 1940 in southwestern Pennsylvania was off nearly 70,000 bbl., largely as a result of the great number oi abandonments, together with the lack of extension of the Washington and Green County pools. Oil wells completed numbered 51, which is 26 more than last year, but the total initial production of 259 bbl. is only 18 bbl. greater than in 1939. There was an increase of 72 over last year for a total of 209f gas wells. However, 68 7 dry holes were drilled, which is 40 more than a year ago. Thus, 328f wells were drilled during the year, and rigs are erected or drilling is progressing on 59 t more. Shallow Development Oil.—Butler County led in number of oil wells completed, with a total of 27 for an initial production of only 69 bbl. Washington County, with 12 new oil wells, one of which made 40 bbl. from the Fifth sand in S. Franklin township, has 95 bbl., while in Allegheny County 9 wells gave an initial of 86 bbl. for the highest Per well average in the area. This initial was given a considerable boost by one 35-bbl and another 2;-bbl. well in West Deer township, where the Fourth sand produced at 1840 feet. Greene County had only one oil well completed during 1940, and Washington County had 12. The subnormal totals for these counties may be explained by the higher cost of completions and the declining price of crude. The first price change in crude during the year occurred on May 22, when a 25 cut was made. A second 25 cut was made July 12, and was followed by a 156 cut on .Aug. 28. This price held until Nov. 12, when there was a restoration of 156. On Dec. 17 a second 156 increase was put into effect, bringing the price to $I.So per barrel. Gas The large increase in the number of gas wells completed may be attributed to three factors; namely, the recently discovered production possibilities of moderately deep, hitherto little tested horizons, together with increased demand and price. The latter has been made possible by a recent decision of the court, which ruled restraining the public service Commision's prohibition of a raise in the minimum monthly charge to small consumers by one of the major gas companies. A portion of the revenue derived in this manner is being passed along to the producer in the form of higher prices in the field. This higher field rate will remain in effect until a new ruling is made, when it will be reduced in proportion to the reduction of the monthly minimum charge. In an effort to extend the chambers Dam Fifth sand oil pool southwest from Amwell township, Washington County, several wells have been drilled. One of these, in Morris township, washington County, had an initial of 3.2 million cu. ft. open flow from the Big Injun sand. This indicates an entirely new productive area for the latter horizon. Allegheny County had one spectacular well in South Fayette township-—at a depth of about 2500 ft. a 4-million-CU. ft.

Jan 1, 1941

By John T. Galey

Production of crude oil for 1940 in southwestern Pennsylvania was off nearly 70,000 bbl., largely as a result of the great number oi abandonments, together with the lack of extension of the Washington and Green County pools. Oil wells completed numbered 51, which is 26 more than last year, but the total initial production of 259 bbl. is only 18 bbl. greater than in 1939. There was an increase of 72 over last year for a total of 209f gas wells. However, 68 7 dry holes were drilled, which is 40 more than a year ago. Thus, 328f wells were drilled during the year, and rigs are erected or drilling is progressing on 59 t more. Shallow Development Oil.—Butler County led in number of oil wells completed, with a total of 27 for an initial production of only 69 bbl. Washington County, with 12 new oil wells, one of which made 40 bbl. from the Fifth sand in S. Franklin township, has 95 bbl., while in Allegheny County 9 wells gave an initial of 86 bbl. for the highest Per well average in the area. This initial was given a considerable boost by one 35-bbl and another 2;-bbl. well in West Deer township, where the Fourth sand produced at 1840 feet. Greene County had only one oil well completed during 1940, and Washington County had 12. The subnormal totals for these counties may be explained by the higher cost of completions and the declining price of crude. The first price change in crude during the year occurred on May 22, when a 25 cut was made. A second 25 cut was made July 12, and was followed by a 156 cut on .Aug. 28. This price held until Nov. 12, when there was a restoration of 156. On Dec. 17 a second 156 increase was put into effect, bringing the price to $I.So per barrel. Gas The large increase in the number of gas wells completed may be attributed to three factors; namely, the recently discovered production possibilities of moderately deep, hitherto little tested horizons, together with increased demand and price. The latter has been made possible by a recent decision of the court, which ruled restraining the public service Commision's prohibition of a raise in the minimum monthly charge to small consumers by one of the major gas companies. A portion of the revenue derived in this manner is being passed along to the producer in the form of higher prices in the field. This higher field rate will remain in effect until a new ruling is made, when it will be reduced in proportion to the reduction of the monthly minimum charge. In an effort to extend the chambers Dam Fifth sand oil pool southwest from Amwell township, Washington County, several wells have been drilled. One of these, in Morris township, washington County, had an initial of 3.2 million cu. ft. open flow from the Big Injun sand. This indicates an entirely new productive area for the latter horizon. Allegheny County had one spectacular well in South Fayette township-—at a depth of about 2500 ft. a 4-million-CU. ft.

Jan 1, 1941

Howard N. Eavenson, Gary, W. Va. (communication to the Secretary*):—For some time before the publication of Mr. Scholz's paper, I had been collecting data bearing upon its subject, and I now take pleasure in presenting to the Institute my results in the form of a discussion. It has long been a matter of common opinion among mining-men that mine-explosions are more frequent during the colder, or winter months, than during the warmer ones, and it is a matter of common knowledge among them that the air-ways and road-ways in most mines are much drier and are more inclined to be dusty during the winter than during the summer. In many mines, places which are wet and sloppy in the summer are dry and sometimes dusty during the winter. These changes, of course, can only be due to atmospheric conditions, and are caused by differences in temperature and humidity. Until recently, however, very little attention has been paid to the part that atmospheric conditions may play in mine-explosions, or, rather, to the effect they may have in rendering mine-conditions peculiarly dangerous, and in spreading and rendering more disastrous the effects of what otherwise probably would have been small explosions. To show the difference in mine-conditions during summer and winter months, I have tabulated in Table I. the results of 24 observations of hygrometric conditions in several different mines at different times of the year. Mines Nos. 1, 2, and 6 are located in the Pocahontas coal-region, in McDowell county,w.Va., the first one being a shaft-mine and the others drift. Mines 1A and 2A are drift-mines located in Logan county, W. Va. All of these are mines of fair size, but none of them has been in operation more than six years,

Jan 1, 1910

[A AALSETH, Earl P (M 51) Consult Geol Engr 2019 Eldorado Dr, Billings, Monl ABADIE, Henry G (M 43) Asst to Supt of Oper Long Beach Oil Dev Co 925 Harbor Plaza, Long Beach 2, Calif ABBE, T Waldo (A 56) Asst Dist Oper Supt Sun Oil Co PO Box 66, Stowell, Tax ABBOTT, Fred E Jr (M 59) Abqaiq Dist Mgr Arabian American Oil Co Dhahran, Saudi, Arabia ABBOTT, Clifton T (A 60) Apartado 677, Maracaibo, Venezuela ABBOTT, J L (M 56) Partner Pritchard & Abbott 1010 Ft Worth Natl Bk Bldg, Fort Worth 2, Tex ABBOTT, Richard H (J 51) Partner Abbott & Howard 422 W Hermosa San Antonio 12, Tex .ABBOTT, William G (M 50) Div Mgr Rice Engrg & Operating Inc Box 1142, Hobbs, N. M. ABDERHALDEN, Ronald R (J 59) Prod Engr Continental Oil Co Box 100, Carmi, III ABEL, Malcolm D (J 50) Gen Partner Abel & Bancroft PO Box 865, Midland, Tex ABEL, Ramond L (M 28) Prof of Chem Eng Univ of Pittsburgh, Pittsburgh 13, Pa ABEL, Wayne K (M 57) 1513 Patton Drive, Odessa, Tex ABELL, Joseph M (J 55) Petr Engr Tennessee Gas & Oil Co Box 1772, Casper, Wyo ABELS, Thomas A (J 60) Exploit Engr Shell Oil Co Box 193, New Orleans 3, La ABENDROTH, G F (M 46) Dring Prod Supt Lyons & Logan 1500 Beck Bldg, Shreveport, La ABERCROMBIE, Bolling A (M 60) Mgr Product Planning Axelson-Garrett PO Box 2427, Longview, Tex ABERCROMBIE, C T (160) Prod Engr Cities Ser Petr Co Box 472, Brownfield, Tex ABERCROMBIE, H L Jr (J 55) Prod Engr Mobil Oil Co Room 1800 Gr PI Life Bldg, Lubbock, Tex ABERCROMBIE, Robert (J 57) Prod Engr Mobil Oil Co PO Box 1770 Shreveport, La ABERG, Richard S (M 57) Area Prod Geol Shell Oil Co of Canada, Box 100 Calgary, Alta, Canada]

Jan 1, 1961

By Eckley B. Coxe

The subject of this paper will be treated as briefly as possible under the following heads : I. The latest designs of some of the machinery used at these collieries in the preparation of coal. 11. The means employed for elevating, conveying and transporting the coal and slate in and about the breaker. 111. The means employed for raising the coal from the mines to the top of the breaker. IV. The iron breaker as a structure. V. The preparation of the coal as effected in the iron breaker. A key to the plates and the letters and numbers designating different parts, will be found at the end of the paper. I. Preparing Coal. Anthracite coal as it comes from the mines is not marketable. The "run of mine" cannot, as in the case of bituminous coal, be sold. Anthracite, being very compact and practically free from volatile combustible matter, burns only at the surface, and it is, therefore, deemed important to have the lumps as nearly of a uniform size as possible, so that between them a large amount of surface will remain exposed to the action of the air without checking the draught too much, or allowing enough air to pass to cool the coal below the ignition-point, In other words, if the pieces of coal of the size of a chestnut and smaller are mixed with lumps of the size of an egg they fill the air-passages and prevent a free draught. It has long been recognized, therefore, that one of the most important points in preparation is to have a uniform sizing, and also to make as large a number of different sizes as can be produced without too

Jan 1, 1891

THOSE NOT MARKED ARE MEMBERS; MARKED THUS t ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR MEMBERS ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD, Genl. Mgr., Chaffers G. M. Co., Boulder City, West. Australia. '05 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Genl. Supt., Iron Mines Div., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, J. W., Min. Engr., "St. Omer," 123 N. Grand Ave., Los Angeles, Cal. '94 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Yamagano G. M., Satsuma-Gori, Satsuma, Japan. '14 || ABRAHAMS, A. I., Student 1391 Madison Ave., New York, N. Y. '14 tACKER, E. O'C., Met Bethlehem Steel Co., Bethlehem, Pa. '86 ACKER, Louis K., JR., Min. Engr 565 Highland Place, Bellevue, Pa. '08

Jan 1, 1917

By L. O. Howard

L. D. RICKETTS, New York, N. Y.-The advance which has been made in Smelting has been in the line of cheaper cost of handling, due to larger units and decrease in losses. At the International smelter, Mr. McGregor designed everything to handle the ore under cover. But we do find an unaccounted for loss of 0.7 per cent. of our copper, which is serious. Mr. Wallace has made a suggestion that I think metallurgists ought to know of and think about. He made it years ago-and that is that one of the chief losses is undoubtedly in the charging and discharging of the calcine cars. His idea is that possibly the dryers and heaters might be put immediately over the reverberatories So that they could discharge in conveyors. They could feed on both sides, and thereby the dust raised by discharging in the cars from the hoppers could be overcome. E. P. MATHEWSON, Anaconda, Mont.-I might Say a few words on the plants we have visited So far. I was particularly struck with the cleanliness of the plants, which is next to Godliness. I noticed also that the skull-cracker arrangement they have for handling their converter slag is very good. And they have paid considerable attention to ventilation, and are taking steps to take care of the health of the men. "Safety first" has been well looked after in all the plants we have visited so far. The steel structures are right up to date, and the buildings are of the most modern type, and everything is conveniently arranged. I think the designers of the plants in the Southwest are to be congratulated on what they have done.

Jan 12, 1916

By Kirtley F. Mather

FROM almost every point of view, petroleum was "strategic mineral number one" during the World War that ended in 1945. Even the spectacular advent of the atomic bomb in the final days of the conflict did not displace it from its position of prime importance, although within a few years uranium will almost certainly be the "number one" material in the minds of military strategists, if it is not even now in that position. But both as fuel and as raw material for chemical industries, petroleum will hold the center of the stage for many years to come. Hardly any other substance illustrates so fully the manner in which science and technology may be combined to achieve the utmost success in contributing to human efficiency and comfort. Fundamental to any understanding of the problems implied by my topic

Jan 1, 1948

By Richard E. McElvain

The mining and other industries have grown and changed with- respect to their requirements for slurry pumps capable of handling high percentages of abrasive materials. Greater solids concentration, higher heads and pressures, and increased flow arc not possible. Today's equipment delivers up to three times the flow-tonnage and 1.3 times the head per stage as compared with pumps of ten years ago. This results in four times the requirement in size and energy. The new centrifugal pumps are capable of handling these requirements at pressures up to 4826 kPa (700 psi), with 6895 kPa (1000 psi) or more being considered for future systems. The latest pumps, functioning at four times the operating requirement on flow-head, weight eight times more than the previous equipment. Efficiency is increased slightly, to about 75 % to 85%. A testing program on equivalent units has confirmed that the added strength and specific design of heavy-duty pumps can meet demanding engineering objectives. Operating life on difficult-to-pump materials is increased from 500 to over 5000 hours of continuous operation; the ten-fold increase in pump operating time is a major design objective.

Jan 12, 1976

By Paul C. Merritt

The story now unfolding on the Mesabi Range is more than just another chapter in the continuing history of iron mining. It is an epic of foresight, research and pioneering instinct just now culminating in the rapid growth of a new industry hardly more than ten years old. And that growth has been impressive. In the decade that has passed since Reserve Mining Co. blazed a trail as the first successful large- scale commercial taconite operation, the number of plants now existing or soon to be operating has grown to six. From Reserve's initial capacity of 3 million tons of pellets per year, total production capacity on the Range has surged to 31.5 million tons while capital investment has leaped from $300 million in 1955 to almost $1 billion today. During the past year alone, more than $500 million has been committed to these projects, an amount probably greater than that going into any other single mining area in the world. There is more yet to come.

Jan 10, 1965

By A. G. Metcalfe

Observations at temperature are used to investigate the phase changes in alloys containing more than 50 pct Co and above 1000°C. The nonsuppressible transformations in cobalt above 1120°C and in the intermetallic compound Co2Cr3 are studied. The liquidus and solidus surfaces are determined. Insufficient data is obtained to complete the constitution diagram. A REVIEW of some of the earlier work on cobalt' and on the binary systems with chromium2-4 and with molybdenum,5 showed that one likely source of differences might be attributed to the presence of phases at high temperatures which could not be retained by quenching. Consequently, the decision was made that only methods of examination at temperature should be used in this work. The correctness of this decision was confirmed during the course of the work by the investigation of the martensitic nature of the transformation in cobalt- and by the decomposition of the high temperature form of the phase Co2Cr3 on quenching.' The use of high temperature methods, including dilatometry and thermal etching led to the postula-tion of the existence of a high temperature form of cobalt with a probable hexagonal close-packed structure, transforming from cubic cobalt over a range of temperature from 1119° to 1145°C.8 One of the important pieces of evidence for this transformation was that it was observed in alloys with chromium and molybdenum which were nonmagnetic at this temperature so that confusion with magnetostriction effects was impossible. These results were not reported in this earlier paper, so that the data given here supply further evidence for the existence of a second allotropic transformation in cobalt. High temperature observations are necessarily much slower in producing results than the examination of quenched specimens at room temperature by conventional means such as X-ray diffraction or microexamination. The investigation has only covered a limited part of the field, as a result, extending from the liquidus down to about 1050°C and from the cobalt corner up to 50 pct alloying elements. The differences between the various reported diagrams for the constitution of the Co-Mo and Co-Cr systems have already been mentioned. The best available diagram in the first system is due to Sykes and Graff' which is shown in Fig. 1. Fig. 2 shows the latest Co-Cr diagram due to Elsea, Westerman, and Manning.' A comparison reveals that these are incompatible because of the disagreement with regard to the number of allotropes of cobalt. Elsea, Westerman and Manning took their liquidus and solidus curves from Wever and Haschimoto.2 The temperature horizontal in the two-phase field beneath the eutectic was placed 35" to 39°C higher than in earlier work2,4 with a new interpretation of the nature of this transformation. This interpretation also required a peritectic horizontal at about 1470°C, which has been confirmed here for an alloy with 53 pct Cr. No investigation had been made of the ternary system until after this work had been terminated, when a section at 1200°C was published." In this work a ternary compound was found by the X-ray diffraction examination of quenched alloys. This compound contained less than 50 pct Co, and was thus outside the field investigated here. However, some reactions were found dilatometrically which could not be fitted on the diagram and are now believed

Jan 1, 1954

By Paul M. Tyler

FOR the same reason that water is not missed until the well runs dry, the roles of many industrial minerals in wartime are often overlooked. In contrast to the growing shortages of many metals, our supplies of most nonmetallic minerals are limited only by our machinery for taking them from the ground and by our processing facilities. With few exceptions, the demand for increased supplies has been met without fanfare or delay. Only Brazilian quartz crystals, certain kinds of mica, and, latterly, industrial diamonds are on the so-called strategic list, although asbestos, beryl, corundum, cryolite, fluorspar, crucible-grade graphite, ilmenite, iodine, kyanite, monazite, nitrates, rutile, and zircon have caused more concern among those responsible for procurement and are included in our preclusive buying programs. Such specialties are needed urgently, but they are far less important in the over-all picture than the more abundant minerals.

Jan 1, 1942

By W. S. Row

This mine is operated at 4000 to 4500 tons daily through a single shaft, with one rock hoist and one senice hoist. Latest shaft construction is concrete with wooden dividers. Economics of drifters and air-leg drills are compared, as well as costs of shrinkage and sub-level stoping. Economy of large haulage equipment and underground crushing is shown. THE property of Kerr-Addison Gold Mines is located in the Larder Lake district of Ontario about 3 miles from the Quebec boundary on the highway between Kirkland Lake and Noranda. It is roughly 320 miles due north of Toronto and 365 miles north of Buffalo, N. Y. The property was staked in 1906 and after several development efforts finally came into continuous production at 500 tons per day in 1937. In 1939 the daily tonnage -was increased to 1200 and in 1941 to 2100 tons. At the end of the war, because of the shortage of labor, tonnage was down to 1100 tons per day, rising to 2200 in February 1947. A further plant expansion inaugurated in 1946 was completed by December 1948, bringing the capacity of the mine and mill to a production rate of 4000 tons per day. Current production, with 880 men employed, is 4400 tons per day. Changes in mining methods and equipment, required by the recently completed expansion program, have yielded interesting comparative results, some of which are described in this paper. Hoisting of ore and waste from the mine, as well as all service facilities for handling men and supplies underground, are provided for in a single vertical five-compartment shaft. Ore and waste are hoisted in 12½-ton skips in balance by a 14-ft diam hoist with drums 115 in. wide, grooved for 2?-in. wire ropes. This hoist, with a total rope pull of 85,000 lb, was designed to operate at a speed of 2600 ft per min to a depth of 4000 ft, hoisting 15 tons of ore in each skip. It is amplidyne-controlled and powered with dual drive dc motors of 2250-hp each, through flexible couplings to two pinion shafts, one on each side of the main gear. Each motor has a peak load rating of 4500-hp at point of greatest duty. Direct current power to the hoist motors is supplied from a motor generator set consisting of a 5000-hp synchronous motor driving two 1750-kw dc generators. The loading pockets used so far are at depths of 1500 and 2725 ft respectively. Consequently the present hoisting speed is 2000 ft per min and the skips capacity only 12½ tons. Now that the shaft has been deepened the new pockets at 3934 ft will be increasingly used so that the speed and the skip size will be increased up to original specifications as required. Some difficulty in meeting the required hoisting cycle is expected because of the shape of the skips. As now in use the cross-sectional dimensions of the inside of the skip are 4 ft 6 in. x 3 ft 8 in. To hold 121/2 tons, therefore, they are 14 ft 10 in. deep. Since the skips are the conventional overturning or Kim-berley type, considerable hoisting time is lost in retardation in entering the headframe dump and in acceleration when leaving. It is expected that to obtain the specified tonnage from this hoist when the skip size is increased to 15 tons it may be necessary to resort to bottom dump skips. This type of skip could reduce considerably the present excessive acceleration and retardation times. Analyses of the skip-hoisting operation are made monthly, and every effort is made to reduce controllable delays. For a nine-month period in 1951 such an analysis shows that the hoist was in operation 92.5 pct of the available time, which was allotted as shown in Table I. Overall hoisting costs, cage and skip, for the year 1951, averaged $0.168 per ton of ore milled. The mine is serviced entirely by means of a single cage, capacity 35 men or 15,700 lb, operating in con-

Jan 1, 1954

By W. Geo. Waring

Introduction THE winning of zinc and lead ores from the comparatively shallow deposits of the Joplin district, presents, few such problems for the mining engineer as are encountered in deep ore mining and in the handling of complex ores. However, for those who are interested in the origin and nature of ore deposits in general, there is much here to investigate, and upon studies in this direction will depend in no small measure the future of an industry that has produced during the year 1916, in southwest Missouri, lead and zinc ores to the value of $26,319,383; adding $46,022,164 to the metallic wealth of the nation. Including the adjacent mines in Ottawa County, Oklahoma, and Cherokee County, Kansas, which are, really continuations of the Joplin district, the total value of ores produced reached the sums of $34,089,503, and that of the metals, $58,927,941.1 The ores produced in the Joplin district are remarkable on account of their almost uniformly high" metal content in both lead and zinc. Their superiority in this regard is unparalleled, and is doubtless clue to certain geological conditions that are now possibly explicable, provided that the artesian circulation = ascension hypothesis of the origin of the ore deposits is proven beyond question to be the only tenable explanation of the facts. These, as well as other valuable zinc-ore deposits, are bound to he exhausted in time, for ordinary mining purposes, acid it concerns the mining engineer that the conditions under which ores of this character were actually deposited in the form in which they occur, may, if possible, be ascertained, in order that he may learn where to look for similar deposits in other regions, or even how to reproduce artificially such condi-

Jan 9, 1917

By Joseph Bernhardt

THE Cornwall Ore Mines, Division of the Bethlehem Steel Co., at Cornwall, Lebanon County, consists of two separate magnetite ore bodies, approximately one mile apart. The one ore body was an outcrop in which open-pit mining operations were begun in 1742 and continued without interruption. This mine is also served by a shaft for mining that portion of the ore body not recoverable by open-pit methods. The other property had no outcropping and is entirely an underground operation. This mine, cap-tioned No. 4 mine, is serviced by two shafts 220 ft apart. The No. 4 shaft is for hoisting rock and ore, and the No. 5 shaft is for handling men and ma- terials. The shafts are on a catenary curve, closely following the dip of the ore body. Slope of the shafts at the collar is 36", flattening to 26" at the bottom. The footwall at Cornwall is a traprock which varies structurally from solid to highly fractured. Grizzly stations at the top of each chute raise were reinforced by setting timber sills on concrete. Occasionally it was necessary to concrete the entire chute raise. Concreting was done by using 35-yd electric mixers set up in the breaking subs. Sand, stone, and cement were hoisted up through the chute raises to the breaking subs. Late in 1937 it was decided to eliminate chute raises and breaking subs in future development. Haulage levels are 50 ft apart vertically. When ore is below a 40 " dip, slushing drifts are driven normal to the haulages and on 40-ft centers. In a few areas, ore dips greater than 40" and slushing drifts are then placed parallel to the haulage drifts. Finger raises are opposite each other and on 20-ft centers making 20x20-ft draw areas (fig. 1). For loading

Jan 1, 1951

By Joseph Bernhardt

THE Cornwall Ore Mines, Division of the Bethlehem Steel Co., at Cornwall, Lebanon County, consists of two separate magnetite ore bodies, approximately one mile apart. The one ore body was an outcrop in which open-pit mining operations were begun in 1742 and continued without interruption. This mine is also served by a shaft for mining that portion of the ore body not recoverable by open-pit methods. The other property had no outcropping and is entirely an underground operation. This mine, cap-tioned No. 4 mine, is serviced by two shafts 220 ft apart. The No. 4 shaft is for hoisting rock and ore, and the No. 5 shaft is for handling men and ma- terials. The shafts are on a catenary curve, closely following the dip of the ore body. Slope of the shafts at the collar is 36", flattening to 26" at the bottom. The footwall at Cornwall is a traprock which varies structurally from solid to highly fractured. Grizzly stations at the top of each chute raise were reinforced by setting timber sills on concrete. Occasionally it was necessary to concrete the entire chute raise. Concreting was done by using 35-yd electric mixers set up in the breaking subs. Sand, stone, and cement were hoisted up through the chute raises to the breaking subs. Late in 1937 it was decided to eliminate chute raises and breaking subs in future development. Haulage levels are 50 ft apart vertically. When ore is below a 40 " dip, slushing drifts are driven normal to the haulages and on 40-ft centers. In a few areas, ore dips greater than 40" and slushing drifts are then placed parallel to the haulage drifts. Finger raises are opposite each other and on 20-ft centers making 20x20-ft draw areas (fig. 1). For loading

Jan 1, 1951

By C. W. Davis

THE name fuller's earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller's earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water by acid which are equal to or more efficient than an untreated fuller's earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.1 The properties that make fuller's earth useful in the treatment of petroleum products by "percolation" and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller's earth and other adsorbent earths.

Jan 1, 1929

By Harold F. Unger, Byron S. Snowden, William H. Engelmann

The effects of using surfactant solutions while diamond drilling in amygdaloidal basalt of the Upper Michigan copper mining district were investigated. Nonionic, anionic, and cationic surfactant solutions, all biodegradable, were tested with size AX surface-set bits mounted on a drill instrumented for continuous recording of thrust, rotational speed, and torque levels. Water flow and penetrations rates were also recorded. A drilling study was carried out, testing two rotational speed levels, two diamond bit grade levels, and four flushing agents (including water as a control). Comparison of all low-speed/high-thrust groups of tests shows that the non-ionic surfactant produced a 35% overall average increase in penetration rate over water, the anionic a 29% increase, and the cationic a 28% increase. These increases in, penetration rates resulted in a 22 to 26% reduction in cost over flushing with water alone. With the high-speed/low-thrust combination, the surfactants produced less benefits in penetration rate increases over water (14% increase for nonionic, 14% decrease for anionic, and 2% decrease for cationic type). Particle size analyses were run on drill cuttings produced by the three surfactant solutions and by water. All surfactant solutions showed a 20 to 50% increase in solids content over that of water alone. Since flushing rates were constant, these increases in solids content agree well with the penetration rate changes. The diamonds were recovered from each bit by matrix dissolution, and bit wear was measured in terms of total loss of weight. Flushing with surfactant solutions showed a savings in bit wear in most cases. The drill team noted also that surfactant flushing improved recovery of drill core by allowing easier removal of the core from the barrel.

Jan 1, 1976

By James T. Kemp

AN historical society of particular interest to mining engineers all over the world was born in Cornwall in 1935. A hundred-year-old winding engine then finished its long labors at the Levant mine on the cliffs near Lands End, England. The engine was to be dismantled and scrapped. A few men living near-by, appreciating that this event was one of the final acts in closing a long century of extraordinary mining and engineering evolution. armed a committee to prevent the destruction of the old mine hoist and succeeded in purchasing the engine. They restored the engine house and in time arranged with the Manor of Trewellard, owners of the land, for a 99-year ground lease on a peppercorn rental.

Jan 1, 1947

By W. Geo. Waring

The winning of zinc and lead ores from the comparatively shallow deposits of the Joplin district presents few such problems for the mining engineer as are encountered in deep ore mining and in the handling of complex ores. However, for those who are interested in the origin and nature of ore deposits in general, there is much here to investigate, and upon studies in this direction will depend, in no small measure, the future of an industry that has produced during the year 1916, in southwest Missouri, lead and zinc ores to the value of $26,319,383; adding $46,022,164 to the metallic wealth of the nation. Including the adjacent mines in Ottawa County, Oklahoma, and Cherokee County, Kansas, which are really continuations of the Joplin district, the total value of ores produced reached the sum of $34,089,503, and that of the metals, $58,927,941.l The ores produced in the Joplin district are remarkable on account of their almost uniformly high metal content in both lead and zinc. Their superiority in this regard is unparalleled, and is doubtless due to certain geological conditions that are now possibly explicable, provided that the artesian circulation = ascension hypothesis of the origin of the ore deposits is proved beyond question to be the only tenable explanation of the facts. These, as well as other valuable zinc-ore deposits, are bound to be exhausted in time, for ordinary mining purposes, and it concerns the mining engineer that the conditions under which ores of this character were actually deposited in the form in which they occur, may, if possible, be ascertained, in order that he may learn where to look for similar deposits in other regions, or even how to reproduce artificially such condi-

Jan 1, 1918