Search Documents

By Martin Chabicovsky, Milan Hnizdil

Emulsions are frequently used for the cooling and lubrication of working rolls during the cold rolling. The fact that the lubrication and cooling are not separable makes the optimization of both functionalities difficult. The higher emulsion temperature decreases the cooling efficiency compared to cold water. Heat transfer and fluid flow laboratory (Czech Republic), CRM (Belgium), Tata steel (Netherlands) and Henkel (Germany) cooperated on the increasing of a cooling efficiency during cold rolling. Part of this research was focused on an influence of the emulsion composition on a cooling intensity. The cooling efficiency was laboratory investigated. The stainless steel sample with thermocouple was heated and then it was cooled by a nozzle. Tests were performed with various emulsions and pure water. The heat transfer coefficient was computed from measured temperatures. The cooling intensity (heat transfer coefficient) of all tested emulsions was similar but an increase of the cooling intensity was found with water. Further various emulsions concentrations were tested. Results showed decreasing cooling intensity with increasing oil concentration. Adding additives therefore is thought to cause a noticeable decrease of the cooling intensity.

Oct 1, 2019

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Julio César de Oliveira Melo, Giuliano Felippe Soares, André Dias Leite

A resolução de problemas na operação industrial é algo complexo e precisa ser baseada em dados, muitas vezes diversos e não estruturados. Este trabalho traz uma abordagem em big data para dar visibilidade dos problemas em sistemas industriais, trazendo insights que permitam sair da intuição para assertividade, contruibuindo, assim, para redução do tempo de detecção e resolução de problemas.

Oct 1, 2019

By Anderson Ayres Bittencourt, Sergio Valle Junior

Um dos grandes desafios nos ambientes industriais é o monitoramento contínuo de aplicações de automação. O difícil acesso a redes industriais e os sistemas legados trazem grande complexidade a esta tarefa. Para resolver o problema, a migração destes sistemas e redes para arquiteturas mais novas e integradas é essencial. E essa migração permite o uso de ferramentas antes só conhecidas no mundo de TI para apoiar o processo industrial trazendo clareza e assertividade na análise de falhas, troubleshoot e monitoramento integrado de todos os sistemas. Traremos neste trabalho um esclarecimento de como foi o modelo implementado nas plantas de Tubarão e Vega e diversos detalhes sobre cada componente escolhido com o propósito de prover uma solução fim-a-fim para o monitoramento de aplicações e ativos de Nível 2 e Nível 1 da Automação.

Oct 1, 2019

By Camila Fernandes Rezende, Camila Simon Christ, Vinicios Andreatta, Marcus Vinícius Pimentel Gomes

A integração e cruzamento de dados de diversos sistemas para as unidades técnicas de processo sempre foi uma necessidade e um desafio. Para a unidade técnica da Aciaria, a integração de dados gerados pela Instrumentação, Automação e MES (Manufacturing Execution System) é imprescindível para a análise e otimização do processo. Este processo feito de forma manual era trabalhoso, improdutivo e com grande potencial de erros. Mesmo com o suporte da área de TI (tecnologia da informação) e TA (tecnologia de automação), em alguns casos este processo era inviável devido à complexidade. Com a utilização de uma ferramenta analítica, já utilizada em outros processos produtivos da empresa (Laminação de Tiras a Quente e Qualidade), foi possível prover acesso a diferentes bases de dados, permitindo a integração dessas informações de forma simplificada, ágil e única, todos consumindo os mesmos dados, com as mesmas regras. A automatização deste processo trouxe benefícios como: melhora na qualidade do dado, democratização das informações e tempo para investigação de problemas e otimização de processo, além de menor dependência das equipes de TI e TA.

Oct 1, 2019

By Luciano Henrique Andrade de Resende, Maria Rita Oliveira Rebouças

O processo de Monitoramento Controles, realizado pela área de Governança, Riscos e Compliance, requer preparação e verificação de um grande volume de dados. Isso feito de forma manual e com a necessidade de cruzar dados de diferentes fontes, torna o processo bastante complexo, impactando diretamente na periodicidade e acurácia dos testes. O objetivo de trabalho era prover uma ferramenta e uma metodologia que fosse capaz de automatizar esse processo, tornando-o contínuo e possibilitando análise de uma grande massa de dados, proveniente de diferentes fontes e com uma saída padronizada. Após análise de ferramentas de mercado e a realização de provas de conceito, foi definida a ferramenta e modelo de trabalho a ser aplicado. O resultado foi a implantação de um processo de Monitoramento Contínuo de Controles (MCC) que traz: ganho de produtividade, ao permitir que testes sejam executados de forma automática; ganho de eficiência, por permitir realizar o teste em toda a base de dados, sem necessidade de amostra; aumento na assertividade, por reduzir probabilidade de erro humano provenientes de atividades manuais; além de retorno financeiro e mitigação de riscos.

Oct 1, 2019

By Herman Pessoa Lima Júnior, José Brant de Campos, Rodrigo Felix de Araujo Cardoso, Paulo Renato Barbosa Marinho, Rauni Coelho da Costa

A técnica de SAXS é um método analítico que possibilita a determinação de diversas propriedades em nanomateriais, onde o colimador é a parte mais importante da óptica deste tipo de equipamento, sendo sua fabricação um desafio. Software de CAD 3D e 2D foram utilizados no desenvolvimento e fabricação de um bloco de colimação e testes comparativos foram realizados com fontes de raios X. Os testes mostraram que a geometria do feixe colimado é condizente com os modelos geométricos previamente resolvidos.

Oct 1, 2019

By Luis Acainas Caballero, Karl Hoen, Stephan Krämer, Christoph Klein

The situation of the steel industry is still challenging. Worldwide overcapacities have an impact on profitability. More than ever, the point at SMS group is to provide the steel industry with flexible and profitable technologies and systems over the whole process chain. One example for that is the thin slab casting and rolling technology and, in particular the CSP® technology (Compact Strip Production), being well established for hot coil production. From its introduction in 1989, CSP® technology has been continuously further developed. Today, on a CSP® plant, the full range of high-quality steel grades can be produced with tightest geometrical and metallurgical tolerances under optimal economic conditions. With the introduction of semi-endless rolling and, as a further step, the endless rolling process, the product range for thin and ultra-thin products has been further enlarged, allowing for the production of hot rolled coils with a thickness of 0.8 mm for low carbon steel grades. Also high-strength steel grades may be produced with gauges below the minimum product thickness that can be achieved in a conventional-type hot rolling mill. Another step in the further development of CSP® technology is digitalization. In December 2016, the CSP® plant of Big River Steel (BRS), located in Arkansas, USA was put into operation. It is the first learning steel mill in the world. The CSP® plant of BRS comes with innovative technologies, providing impressive operational results right from the beginning.

Oct 1, 2019

By Michael Windhager, Karl H. Ziehenberger

ULTIMA® are high performance, centrifugal cast, double poured (CC duplex) work rolls. This paper describes the principle of the ULTIMA® roll concept and its wide range of usability. The ULTIMA® concept provides a solution for rod and bar mills to increase performance and output, even under harsh rolling conditions. The main focus is on highly loaded mill stands that require both high wear resistance and resistance against thermal fatigue, like pre-dog bone, dog bone, slitter. Specific case studies of quite different mill configurations and rolled product mix prove the positive impact on production yield, mill and roll shop operations, and profitability in terms of TCO (total cost of ownership).

Oct 1, 2019

By Edilson Alves Maranhão, Willi Anton Buehler, Andrea Pezza

O processo de vácuo é a solução típica aplicada quando é hora de atualizar o nível de qualidade do aço de uma aciaria existente. A instalação do novo Tanque de Desgaseificação à Vácuo (VD) de 135t no Canadá e do novo RH de 150t na planta integrada no México para a produção de tubos de alta qualidade na América do Norte é um exemplo típico disso. A nova instalação inclui o mais recente conceito de design para este tipo de equipamento: operações totalmente automatizadas e menor impacto ambiental são os principais aspectos do projeto. A solução de bomba mecânica a seco continua sendo a melhor abordagem de investimento e custo operacional para a tecnologia de vácuo. Os principais aspectos do design da planta são descritos neste documento. O desgaseificador a vácuo VD é responsável pela melhoria das performances metalúrgicas, especialmente em termos de nitrogênio, remoção de hidrogênio e nível de pureza do aço. O processo a jusante e os resultados estão estritamente ligados aos desempenhos do desgaseificador a vácuo. O monitoramento de processos através da linha completa é uma prática padrão para obter uma melhoria efetiva da qualidade do produto. Os desempenhos metalúrgicos do desgaseificador a vácuo VD são analisados e comentados neste trabalho.

Oct 1, 2019

By Valeria Collini, Antonello Mestroni, Enrico Plazzogna

The Danieli Group is deeply involved in the technological improvements stimulated by Industry 4.0 concepts widely applied to the metals industry and process automation. The so-called "Intelligent Mill" is the natural evolution of the company’s consolidated know-how and undisputed leadership in the fields of mini-mill and turnkey plants. Complete and structured data collection is the basis for real-time analysis and process optimization in terms of quality, efficiency and easy maintenance. A centralized repository of information is possible thanks to the strong interconnection between process control system architecture and intelligent sensors, together with dedicated software tools leading to an intuitive approach to data analytics.

Oct 1, 2019

By Gabriel Duarte de Andrade, Arnaldo Veronêz Júnior

Em um processo de sinterização, a velocidade da máquina de sínter deve ser controlada, com o intuito de garantir que o ponto final de queima da camada a sinterizar esteja dentro de uma faixa que possibilitará elevada produtividade. Este artigo apresenta um modelo físico que descreve o movimento da frente de queima da camada ao longo do leito e o controle de velocidade implantado no sistema de automação de nível 2 da Sinterização da ArcelorMittal Tubarão. O controle de velocidade foi proposto para manter o ponto final de queima em torno do valor do setpoint escolhido. Ao longo dos anos, as condições operacionais da planta de sinterização mudaram em razão da variação da qualidade dos minérios que compõem a mistura. Nesse contexto, o controle foi avaliado e apresentou resultados satisfatórios, permitindo à operação uma forma de controlar o processo sem adicionar atrasos relacionados à tomada de decisão.

Oct 1, 2019

By Antônio Augusto Gorni, Fabio Adriano da Silva, Emanuelle Garcia Reis, Afrânio Márcio Costa

Gerdau Ouro Branco´s plate mill started the operation in 2016 with high level technology. Stands out the capacity to produce different thicknesses in a same plate, therefore allowing special service for sectors such as building structures, bridges, shipbuilding and mechanical applications. The purpose of this study is to present the first results obtained in this innovative product in Brazil. Some slabs of EN10025-2 S355JR+AR steel were rolled and were evaluated the dimensional tolerances, mechanical properties uniformity, grain size, surface and internal qualities. In addition, a correlation was observed between slab and plate thickness reduction and internal plate quality. The results show that this technology can be used with adequate performance for these steel grades in the current market.

Oct 1, 2019

By Haruki Inami, Takashi Ishida, Kazuhiro Ohara, Hiroyuki Imanari

The highly competitive business environment of the international metals industry is driving demand for more cost-effective operation of steel making facilities, rolling mills, and strip processing lines. Achieving stable operation is vital if the steel industry is to produce high-quality products constantly and productively. In recent years, advances in computer processing speeds, data acquisition rates, and data storage capacity have rapidly led to greater use of the new technologies of big data, analytics, the IoT, and AI by control system designers and process engineers, and the introduction of industrial applications. The “Smart Rolling Mill” solutions for hot strip mills have been developed by our group with the goal of achieving sophisticated, state of the art, and automated operation in steel rolling mills. The various solution engines improve process stability, increase the performance of mill equipment, and provide improved process control. These solution engines are based on extensive knowledge of the rolling process and the associated control systems. Two solution engines in particular are the diagnosis systems for rolling condition and for product quality that contribute to cost-effective operation and lower yield loss. This paper focuses on the diagnosis systems for rolling condition and for product quality in hot strip mills. Advanced information technologies using big data analytics and machine learning are applied to real-time data collected from the automation system that controls operation and the rolling process. We have developed diagnosis solutions for rolling condition and product quality utilizing predictive and clustering diagnosis. Predictive diagnosis prevents serious problems by detecting changes in the state of the plant or in the rolling condition. Clustering diagnosis classifies patterns of fluctuation in product quality trend charts, providing effective tuning guidance for improving product quality. This paper describes these applications with several examples.

Oct 1, 2019

By Henrique Lacerda Eleutério, Aldo Henrique de Almeida Barbosa, Vicente Tadeu Lopes Buono

The automotive industry’s interest in galvannealed (GA) boron steel for hot forming processes application has been steadily increasing due to its excellent surface quality, galvanic protection provided to the parts, good paint adhesion and better weldability in relation to other coatings for this application. In this study, samples of 22MnB5 galvannealed steel were heat treated and hot stamped on a water cooled die in laboratory scale. The influence of heat treatment on stability of coating and steel was assessed by using initial heating rates 11.0ºC/s and 15.0ºC/s. Microstructural evolution of galvannealed coating and structural integrity of steel during hot forming were investigated by scanning electron microscopy with energy dispersive spectroscopy analysis (SEM/EDS/Line scan), X-ray diffraction (XRD) and optical microscopy (OM). It was possible to quantify the Fe-Zn phase evolution during hot forming, to understand the effect of these heating rates on the product properties and to establish an optimized heat treatment for hot forming of these steel. The heat treatment with the heating rate of 15.0ºC/s presented greater operational flexibility and final products free from surface defects or cracks in the substrate.

Oct 1, 2019

By Roberto Gomes da Silveira Junior, Marcos Cordeiro Fonseca, Geraldo da Conceição Morais, Manoel Gomes de Souza Neto

Sinter maximization in the blast furnaces charge has proven to be the most economically viable way to produce pig iron at Usiminas. This fact has led the company to develop projects aimed at increasing the production of sintering. In this context, the present work shows the recent experience of Sintering Machines 1 and 2 drum mixer exchanging contributing to the increase of operational productivity due to the optimization of the original design. For 13 days was the replacement of the original drum installed in 1974 by a new drum with improvements in the design of the internal and the sprinkling water system. The improvements contributed to the effective formation of micro-pellets and, as a result, increased productivity of Sinter Machines. Several aspects of the project are presented: engineering, planning, safety, manufacturing, technical quality, schedule and a comparison between the parameters of the equipment operation before and after the implantation

Oct 1, 2019

By Eduardo Poltronieri Trés, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Anderson Denadai Thomzini

The first industrial applications of roller presses at the comminution were in 1984 in the cement industry. Since then, the equipment has taken more space in the mineral industry. However, many challenges are still present in this equipment, more specifically regarding to ore breakage predictability. The application of this equipment in the pellet feed preparation is fundamental to increase the surface area (blaine index) of the mineral using reduced energy consumption. However, even after several pressing steps, it is still challenging to achieve granulometry in percentages required for the pelletizing process. Currently these levels are reached in wet milling processes, typically carried out in wet ball mills. For the of pellets formation in pelletizing plants, both pelletizing and the firing processes requires finer granulometry. The motivation of this work is to study the pelletizing process, comparing the physical quality of the pellets produced only through comminuted ore in roller press the pellets produced in conventional comminution using circuit with ball mill.

Oct 1, 2019

By Bruno Pinheiro Silva, João José dos Santos Carvalho, Flávio Túlio Busatto, Leonardo Passos Perdigão

Sinter has high participation in the blast furnaces ferrous burden in ArcelorMittal Tubarão, being therefore of paramount importance the constant control of its physical, chemical and metallurgical qualities, aiming at the fulfillment of the client required quality. With the great challenges faced by market conditions, steelmaking companies seek operational sustainability, aiming at stability and reducing costs. One of the main steps to obtain these results in the Blast Furnaces is the raw materials quality stabilization, in order to guarantee the perfect burden distribution control and a better use of the reductant gas inside the reactor, aiming a lower fuels consumption. It is known that the smaller a ferrous particle is, better its reducibility, since a larger surface area provides greater contact with the reductant agent. Based on this concept, the objective of this work is to quantify the effect of the sinter size produced in ArcelorMittal Tubarão Sinter Plant in its reducibility, and in this way enable the definition of a better sinter particle size distribution aiming at a balance between the permeability effects and gaseous yield in the Blast Furnaces. In addition, the reducibility effects on sinter size reduction were evaluated, where the 5 to 10 mm fraction was analyzed in two sinter samples, the first obtained from the conventional route and the second after crushing of the fraction over 50 mm, in order to simulate the effect of the use of a Secondary Crusher in Sintering.

Oct 1, 2019

By Denisio Miranda Custódio, Rodrigo Boyer, Josiane Lira Batista Haagensen, Raquel Teixeira Pereira, Felipe Viana Pimenta, Rossano Augusto Pilon Nunes

In the Tubarão Pelletizing Plants, anthracite is used as solid fuel, which has fixed carbon content of 72%. This paper will present the pilot scale results and industrial scale tests of an alternative fuel to anthracite, named Blast Furnace Dust. All the work was developed using samples from Arcelor Mittal Tubarão, due to it has a large source of production and is near to Vale/SA, which reduces significantly the cost for the material’s transportation. There was an impact on the variability in fixed carbon results of the slurry, mainly at the beginning of the test, reaching very high levels and put on risk the pellets physical’s quality. This variation can be explained by some operational disturbances and, mainly, by the low predictability of Blast Furnace Dust quality and lack of an adequate system for material preparation and dosage.

Oct 1, 2019

By Ismael Vemdrame Flores, Lindaura de Souza Cândido D’ Avila, Maurício Covcevich Bagatini, Arthur Felipe Lino Oliveira, Rafael Adriano Lopes Júnior

The use of pellet feed to adjust the chemical quality of the sinter is an alternative to the depletion of iron ore reserves. However, the addition of ultrafine in the sintering process can cause decrease of permeability and consequent drop in machine productivity. In this context, the present work investigated the addition of natural and ground pellet feed, evaluating its effects on cold agglomeration for sintering and quality of quasi-particles produced. Eight typical mixtures with industrial composition were produced in the laboratory, replacing Sinter Feed with different percentages of Natural Pellet Feed (NPF, 91% <150 μm) and Ground Pellet Feed (GPF, 83% <44 μm). The mixtures were subjected to cold agglomeration tests and the quasi-particles produced were evaluated by screening, shatter test, permeability test and disintegration into primary particles analysis. There was a decrease in the mean particle size of quasi-particles and reduce in permeability with addition of the ultrafines. The addition of NPF favored the layering mechanism in larger quasi-particles. The coalescence mechanism occurred for larger additions of NPF and GPF, being more expressive for GPF additions.

Oct 1, 2019