Search Documents

The process of hydraulic transport through pipelines, worldwide well known for the transport of fine-grain solids is also being used to a greater extent in mining for the handling of primarily coarse-grain solid û water mixtures for the removal of, for instance û coal and waste mixtures after coal winning using hydraulic monitors, tailings for backfilling underground and washer tailings and flotation waste to the dump. A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining Research Company) in Essen-Kray, GFR, to further improve this technology. The unit was planned and built by Krupp Industrie- und Stahlbau of Duisburg in cooperation with Bergbauforschung GmbH. The paper deals in detail with the demands made on this test unit and the technical results obtained on it and with the planned experimental research work.

Jan 1, 1980

By E. Munnik

The Chambishi Metals Cobalt Plant in Zambia has recently installed a novel oxidation/precipitation pressure leach process as part of the COSAC (CObalt from Slag And Copper as by-product) Project. Aniron-cobalt-copper alloy, produced by the carbothermic reduction of slag, is atomized and pumped to the COSAC Leach Plant, where cobalt and copper are recovered as dissolved sulphate salts, andiron is rejected primarily as hematite. Cobalt and copper are subsequently recovered as cathode metal in the existing Chambish ioperation by conventional electrowinning. This paper examines the challenges faced during the design and subsequent successful commissioning of the COSAC Leach Plant. The challenges discussed include alloy handling, autoclave design, autoclave cooler design, residue liquor recovery and the water balance design. Keywords: Chambishi, Avmin, COSAC, Zambia, Copperbelt, cobalt, copper, alloy handling, pressure leach, autoclaves, cooling, filtration.

Jan 1, 2003

By Steve Dillingham

There are some blasters and blasting companies that just seem to have better safety reputations than others. This is in spite of the fact that they are essentially doing the same type of work under similar conditions. To achieve that enviable safety reputation, it simply comes down to a strong safety culture prompted by a responsibility for others, as well as yourself and your company.

Jan 1, 2003

By J. P. Neumann, L. Raymond

At temperatures near 1000°C, only the (112) (111) slip systems are operatire in tungsten. Therefore, the substructure introduced into the billet upon rleforming a single crystal by rolling at 1000 "C can be controlled by proper selection 01. processing ral'iubles. Using a reduction of 10 pct pel- pass, the (001)[110] and the (110)[001] crystals will deform by duplex slip rip to a 50 pet reduction in thickuess. These rolled single-crystal sheels are characlerized by anisotropic hardening, retention of ductility with warm working, lattice bending which is related to the conlacl (angle, and macroscopic dimensional changecs in the length bid not the width of the billet. When several slip systems become operative, a greater degree of work hardening is itztvoducetl into the crystal. This rolling- condition is characlerized by isotropic hardening, loss of ductilily with warm working, complex lattice distortions, and macro-scopic dimensional changes in both the length rind Width of the billel. IN tungsten, the {1 10}(111) slip systems are operative below room temperature,' while above 700°C only the {112{ (111) slip systems are observed.2,3 In the transition region, i.e., room temperature. both systems appear. It is the purpose of this investigation to show that tungsten single crystals deformed by rolling at a temperature where only one slip system is operative generate dislocation substructure which depends on the crystal orientation. For a specific crystal orientation. the resulting dislocation substructure can be further influenced by modifying the rolling procedure. Crystals oriented for multiple slip display less substructural sensi- tivity to modifications in processing techniques than do single crystals oriented for duplex slip. Under simple slip modes of deformation, very little work hardening is introduced into a rolled single-crystal sheet. Mechanical properties such as room-temperature strength. ductility, and hardness are used to confirm the existence of the different work-hardened conditions generated within the crystal by modified warm-rolling techniques. EXPERIMENTAL PROCEDURE Material. Single-crystal billets of four different crystal orientations. grown by the Arc-Verneuil technique. were ground to a size of 0.25 by 0.375 by 3 in. In terms of their rolling plane and rolling direction, the billets had the following orientations: (1101 [001 ] (110) [110] (001) [110] (001) [100] The actual orientation of all crystals was within 5 deg of the ideal orientations. The typical impurity content of the crystals is given in Table I. Polishing and Etching. Polishing was done elec-trolytically in a 20 g per liter aqueous solution of NaOH at approximately 10 v. It was established by the Laue back-reflection X-ray technique that the surface damage due to grinding and cutting operations with a diamond wheel did not exceed 0.001 in. Therefore after each cutting or grinding operation at least 0.002 in. was removed electrolytically from the surface in order to eliminate surface effects. By lowering the voltage to 3 v, subgrain boundaries and individual dislocations are identified in agreement with Berlec 4 where the etch-pit traces on a cubic plane form a square. The etching time was about 5 sec at room temperature. Rolling. Rolling was carried out on a Loma 2-high mill (Model 600). The peripheral velocity of the 6-in.-diameter rolls was 500 in. per min, with the surface temperature of the rolls about 400° to 450° C The billets were heated before each pass for 30 min in argon to 1000 C. Oxidation of the crystals during rolling in air resulted in a thin layer of greenish-yellow WO 3 This oxide was removed after each pass by immersing the crystals for a few minutes in a boiling NaOH solution. Prior to the initial rolling pass, a surface layer of 0.001 in. was removed by polishing. The crystals were then annealed in vacuum (10-4 torr) at 2400 C for 30 min. All crystals were rolled in the same direction; i.e., the same end was always introduced into the rolls. The rolling program was conducted in

Jan 1, 1965

By C. J. A. Davie

"SUMMARY A practical application of nitric acid oxidation of sulphides, based on the principles of the Arseno process, has been developed for the Cinola ore. Development of the process has been based on testwork conducted by Bacon Donaldson of Vancouver and Hazen Research of Denver, and on conceptual engineering performed by Minproc Engineers of Denver.A comprehensive Stage II report for the project has been submitted to the B.C. permitting agencies, containing provisions for a zero discharge tailings impoundment system and prevention of acid mine drainage. Approval in principle is expected in early 1989.A feasibility study recently completed by Minproc Engineers and Davy McKee Corporation demonstrates that this project can be brought to production for a capital expenditure of C$120 million for a mill throughput of 6,000 tonnes/day and operated at a total direct operating cost of less than $20/tonne.INTRODUCTION The Cinola orebody was discovered in 1970. It is situated approximately in the centre of Graham Island, the largest of the Queen Charlotte Islands. It represents the mid to upper levels of a hydrothermal precious metals system, characterized by intense brecciation and silicification. Gold is associated with finely disseminated sulphides in a breccia matrix and in free form in numerous quartz veins.Ownership of the property has changed hands a number of times, and previous attempts to bring the property to production have failed. Two critical factors have frequently been blamed for difficulty in creating a successful project: namely, process and environment factors, hence the title of this paper.City Resources (Canada) Limited (""City"") acquired the property in 1986, and commenced an aggressive campaign to verify ore reserves, to carry out metallurgical research and to address environmental issues.PROJECT OVERVIEW When the Cinola orebody was discovered, the significance of hydrothermal mineraliza¬tion associated with crustal plate boundaries was not recognized, and for several years, the orebody was considered an uneconomic curiosity. If the type and location of orebody sought by many companies engaged in gold exploration were to be specified, it would probably be a description of the Cinola orebody - it is a large (greater than 1.5 million ounce), low grade (2.45 gm/tonne), refractory ore reserve associated with the Pacific rim crustal plate boundary. The industry appears to have recognized in the past few years that its future lies in the exploitation of such orebodies, and is prepared to come to grips with the technical problems associated with such ores. In this sense, the Cinola orebody might be considered to have come of age."

Jan 1, 1989

By S. Raghavan

An investigation of the possibility of improving the grinding characteristics of a gabbro ore containing copper and nickel sulfides via a thermal shock treatment technique has been carried out. The results obtained indicate that the breakage characteristics of the gabbro are particles can be significantly improved by preheating the are particles to a temperature around 400°C followed by rapid water quenching. For a given power input and feed size, the thermally treated material produces a product of much finer distribution than the untreated material. An assessment of the improvement in grindability has been made by calculating feed size selection functions for untreated and heat-treated materials.

Jan 1, 1981

By W. Robert, J. Wirth, G. Grasselli

ABSTRACT: Strength, deformability and fluid flow properties of rock joints are to a great extent controlled by the surface roughness. The hydraulic conductivity of a rock fracture depends on the aperture distribution, the surface roughness and the contact area, each of which depend on the stresses that act on the fracture plane. However, despite much recent work, a complete understanding of the relationship between void space geometry, contact areas, applied stress, and hydraulic conductivity has yet to be achieved. Moreover, although in situ rock joints are subjected to both normal and shear loading, few studies have been conducted to investigate the effect of shear displacements on fluid flow through a single rock fracture, and which have addressed the issue of flow anisotropy induced by shearing. Experimental flow tests show that with increasing shear displacement, the fracture becomes heterogeneous and anisotropic, and becomes more permeable in the direction parallel to the displacement (Yeo et al., 1998). On the other hand, dry shear tests show that the surface fails in areas facing the shear direction (Grasselli and Egger, 2003). Moreover, the experimental results confirm that the shear strength of rock joints is direction-dependent. In this paper, a three-dimensional morphological description of several a natural fractures that have undergone shear displacement were generated using the Automated Topographic System at the University of Basel. The data analysis method of Grasselli (Grasselli et al., 2002a) is used to determine the surface parameters that are known to control the shear strength. Simulations of fluid flow through this fracture, in various directions relative to the direction of shear, are conducted using an FEM flow simulator. The results constitute the most detailed analysis yet undertaken of the relationship between shear displacement, shear strength, and fracture transmissivity. RESUME: La rugosité des joints en roche joue un rôle primaire sur la réponse hydromécanique du massif fracturé. En effet, la conductivité hydraulique des discontinuités en roche est influencée par la rugosité, et par la distribution des ouvertures et des zones de contact, dont chacun dépend de l’effort normal et du cisaillement qui agissent sur la surface du joint. Les essais d'écoulement en laboratoire montrent que si cisaillée, la fracture devient anisotrope, et plus perméable dans la direction parallèle au déplacement (Yeo et al., 1998). D'autre part, les essais de cisaillement indiquent que seules les zones de la surface qui font face à la direction de cisaillement sont impliquées dans le cisaillement (Grasselli et Egger, 2003). D'ailleurs, les résultats expérimentaux confirment que la résistance au cisaillement des joints de roche est dépendante de la direction. Dans cet article, plusieurs fractures en roche ont été analysées en utilisant un système de mesure topographique à l'Université de Bâle. La méthode d'analyse de données proposée par Grasselli (Grasselli et al., 2002a) a été employée pour calculer les paramètres de la surface qui déterminent la résistance au cisaillement. Plusieurs simulations du coulage, dans diverses directions relativement à la direction du cisaillement, ont été faites à l’aide d’un programme de calcul à éléments finis. Les résultats constituent une des analyses les plus détaillé sur le rapport entre le déplacement pendant le cisaillement, la résistance au cisaillement, et la transmissivité spécifique de la fracture. ZUSAMMENFASSUMG: Die Festigkeit, Verformbarkeit und Hydromechanik von geklüftetem Fels wird hauptsächlich von der Oberflächenrauhigkeit der Bruchflächen bestimmt. Die hydraulische Leitfähigkeit einer Kluft hängt von der Verteilung der Rissbreiten, der Oberflächenrauhigkeit und den Kontaktflächen ab, die ihrerseits von dem auf die Bruchfläche wirkenden Druck beeinflusst werden. Obgleich in letzter Zeit viel in dieser Richtung geforscht wurde, kann der Zusammenhang zwischen Porenraumgeometrie, Kontaktflächen, wirkendem Druck und hydraulischer Leitfähigkeit noch nicht vollständig erklärt werden. Obwohl Klüfte in situ sowohl Normal- als auch Schubspannungen ausgesetzt sind, wurde der Einfluss von Scherverschiebungen auf den Kluftwasserfluss und die daraus resultierende Fliessanisotropie in einer einzelnen Kluft bisher kaum untersucht. Experimentelle Untersuchungen des Durchflusses zeigen, dass die Kluft für größer werdende Scherverschiebungen heterogen und anisotrop wird wobei die Permeabilität parallel zur Verschiebungsrichtung ansteigt (Yeo et al., 1998). Andererseits zeigen trockene Scherversuche, dass die Oberfläche an Stellen versagt, die gegen die Verschiebungsrichtung anstehen (Grasselli und Egger, 2003). Des weiteren bestätigen die experimentellen Ergebnisse eine Richtungsabhängigkeit der Kluftscherfestigkeit. In diesem Artikel wird eine dreidimensionale morphologische Beschreibung mehrerer natürlicher, durch Scherspannungen verschobener Klüfte vorgestellt, die vom Automated Topographic System der Universität von Basel erstellt wurde. Das von Grasselli (Grasselli et al., 2002a) entwickelte Datenanalyseverfahren wird zur Feststellung der die Scherfestigkeit bestimmenden Oberflächenparameter herangezogen. Mittels einer FEM-Simulation wird der Durchfluss durch eine solche Kluft in verschiedenen Richtungen simuliert. Die Ergebnisse stellen die bisher ausführlichste Analyse des Zusammenhangs zwischen Scherverschiebung, Scherfestigkeit und Durchlässigkeit (Transmissivität) einer Kluft dar.

Jan 1, 2003

Jan 1, 1967

By Irvin G. Burough

Andros Analyzers Incorporated has designed and built two prototype continuous methane monitors capable of being mounted on a mining machine'. These instruments were designed for in-mine safety use. The monitors incorporated an NDIR optical/electronic analyzer design in which the response to the sample gas (methane in air) was achieved by synchronous detection and measurement of the amplitude oscillations of the trasmitted energy from an infrared source caused by the pressure modulation of the sample gas within the optical cell. Zero and span stability were to be achieved by the amplitude modulating of the infra-red source and using detected signal to correct for optical/electronic system variation. This design effort was to simplify and reduce the cost of the major components while eliminating the need for daily calibration. This report is the final report on this effort.

Jan 1, 1981

By William Stewart, John Tinkler, Gary B. Hemphill

Of the 345 km long Taiwan High Speed Rail Project, connecting the cities of Taipeiand Kaohsiung, the 23 km alignment on Contract C230 required the construction of5755 m of shallow mined tunnels ranging from 137 m to 1285 m in length. All nine of these tunnels were mined using NATM methodology. On September 6, 2002, a collapse occurred in Tunnel T08 that affected approximately 50 m of tunnel. There was little warning. However, the crew was evacuated approximately 45 minutes prior to failure and thus, no injuries or loss of equipment. This paper will discuss the mining methods, jet grouting ground support, and the instrumentation selected for the rehabilitation and monitoring of the tunnel.

Jan 1, 2005

By A. Boominathan

The behaviour of single piles under lateral dynamic loading is very critical and the study is still a current field of research since 1950's. Though many methods have been developed analytically to estimate the dynamic lateral stiffness, very limited dynamic testing on full scale piles were carried out to study the response of piles under lateral dynamic loading. Hence, field lateral dynamic vibration tests are conducted on driven precast concrete square pile of 400mm size and driven cast in-situ concrete piles of 400mm and 500 mm diameter at a petrochemical complexes site at Haldia (India). The results of steady state and free vibrations tests are discussed herein and compared with the response of the piles estimated from PILAY.

Jan 1, 2002

By C. W. Morris

The continuous miner training system provides classroom materials training aids, and a continuous miner simulator to provide a short, intensive instruction and skills development program for training or retraining continuous miner operators. This project included refinement of training objectives, revision of training aids, improvements to the simulator, and evaluation of the entire system. This report describes the revised classroom materials and the validation of the training system.

Jan 1, 1982

By D. M. Wyslouzil

"Micron or sub-micron size gold inclusions in sulphide minerals cannot be extracted by conventional cyanidation. The gold surfaces must first be exposed by decomposition of the sulphides. As an alternative to roasting, pressure oxidation was found to be a most satisfactory method to decompose the sulphides and expose the gold particles. For cyanidation the pressure oxidation pulp has to be neutralized and stabilized with lime. It was found that thiourea can extract the gold directly from the pressure oxidation pulp without pH adjustment and oxidant addition. The main obstacles against the common use of thiourea are circumvented by a recently described control method of the emf during leaching.INTRODUCTION Amalgamation and cyanidation are the most conventional processes for gold extraction. The prerequisite for gold extraction is the possibility of gold surface to be contacted by mercury or by the cyanide solution. Encapsulated gold has little chance of contact and this leads to poor extractions.The reasons why a gold ore may be refractory are: micron or sub-micron size gold particles included in the sulphide minerals, such as pyrite and arsenopyrite; presence of and association with antimony, arsenic, tellurium and carbonaceous minerals. Some alternative processes, such as double oxidation(1,2), pretreatment with lime , H202, chlorine and Caro's acid, roasting and thiourea leach, have solved some of the problems of ""refractory"", but the sub-micron gold in sulphide minerals still shows little response. Roasting and the cyanidation of the calcine was one of the most successful approaches for this type of gold ore.There are two disadvantages to the roasting process: (1) the generation of sulphur, arsenic, antimony and mercury containing gases is undesirable and the control is extremely expensive; (2) gold particles might be fused in the roasted product and the oxidized base metals in the calcine might reduce the cyanidation efficiency. In recent years the pressure oxidation process has been considered as one of the more effective and satisfactory methods to decompose the sulphide minerals and expose the gold surface to the cyanide leach solution. The pollution problem could be better controlled and the gold extraction is more amenable."

Jan 1, 1985

By Gary Almeraris, Vincent Jr Tirolo

Traditionally, “Means and Methods” were the sole responsibility of Contractors. However, because of a number of litigious projects in the 1970s, Owners and their Engineers began including Suggested Methods of Construction (SMC) in Contract Drawings. By the late 1990s these SMCs were becoming baseline “Means and Methods” with Contractor recommended changes often considered as Value Engineering proposals. By 2004, the word “Suggested” was sometimes changed to “Prescriptive.” Owners are also purchasing TBMs and other mining equipment for Contractors prior to bid. Is limiting the contracting community’s innovation in developing their own “Means and Methods” and selecting their own equipment in the best interests of the Owner? Does it reduce the Owner’s, Engineer’s or the Contractor’s risk? Are claims reduced and finally what is the impact on the bid? A questionnaire was sent to more than fifty senior engineering field and management personnel representing more than 30 heavy construction companies to ask their opinion on these questions.

Jan 1, 2005

By Frank D. McGuirk

Underground coal mining is traditionally hazardous. Although many danger-prone human activities are now performed by mechanized equipment, this mechanization has itself brought new dangers to the underground mining industry, and the loss of life and limb has caused increased concern for mine safety. The 1969 Federal Coal Mine Health and Safety Act has precipitated a great deal of safety-related research on the part of the Government, industry, and private agencies. Much of this safety research has been focused on the new and varied man-machine interfaces caused by increased mechanization. Recent projects in this area have dealt with standardized controls, emergency shutdown capabilities (panic bars, strike plates, self-centering controls, "dead man" controls), and machine operator protective devices (fully enclosed cabs, canopies, side rails). There was a need for integration of the findings of current and past projects to move rapidly toward the smooth, orderly implementation of standardized operator work station designs for underground mining equipment.

Jan 1, 1975

By R. Barany

In this paper, closed expressions have been obtained for the frequency spectrum of a Born-Karman square lattice in terms of elliptic and hyperelliptic integrals. This work is part of continuing research by the Bureau of Mines with the thermodynamic properties of metals and minerals. Although other workers have obtained various types of approximations for the general case of the frequency spectrum of a square lattice, no one previously has obtained closed analytic expressions for this spectrum. To understand the optical and thermodynamic properties of crystals, several investigators have studied the distribution of frequencies of normal modes of vibration of the crystal lattice. Born and Karman3 laid the foundation for the theory of lattice dynamics and obtained detailed results for the case of a one-dimensional lattice. Blackman4 used numerical techniques to estimate the frequency distribution of a two-dimensional square lattice. Mbntroll5 analytically determined the frequency distribution of a square lattice for a particular value of the force constants. He also studied the more general problem and obtained some analytic approximations, using the method of moments. However, the calculations by this method were so difficult that it was not always practicable to carry them out. Van Hove6 and Montroll7 studied the nature of the singularities in the frequency spectrum of both a two and

Jan 1, 1962

By S. -H. Chang, C. -I. Lee, Y. -K. Lee

Based on results from triaxial compressive tests, an experimental damage model to simulate post-peak behaviours as well as nonlinear behaviours before peak strength was developed. In order to consider pre-peak behaviours, variations of elastic constants at each damage level were regressed by functions of confining pressure. In addition, post-peak behaviours were simulated successfully by using Hoek-Brown constants. As results, the experimental model could predict nonlinear behaviours, peak strengths and stiffness changes observed in experiments. Basé sur des résultats des essais compressifs à trois axes, un modèle expérimental de dommages pour simuler des comportements de poteau-crête aussi bien que des comportements non-linéaires avant la force maximale a été développé. Afin de considérer des comportements de pré-crête, des variations des constantes élastiques à chaque niveau de dommages ont été régressées par des fonctions de pression d'emprisonnement. En outre, des comportements de poteau-crête ont été simulés avec succès en employant des constantes de Hoek-Brunes. Comme résultat, le modèle expérimental a pu prévoir des comportements non-linéaires, des forces maximales et des changements de riidité observés dans les expériences. Auf Basis der Ergebnisse des dreiaxialen Drucktests wurde das experimentelle Schadensmodell, das sowohl das nicht-lineare Verhalten vor der maximalen Stärke als auch das Verhalten nach der maximalen Stärke simulieren kann, entwickelt. Um das Verhalten vor der maximalen Stärke zu berücksichtigen, wurden die Veränderungen der elastischen Konstante bei dem jeweiligen Schadensniveau durch die Funktionen des begrenzten Drucks zurückgegangen. Außerdem wurde das Verhalten nach der maximalen Stärke unter Benutzung von Hoek-Brown Konstanten erfolgreich simuliert. Schließlich konnte das experimentelle Modell das nicht-lineare Verhalten, die maximale Stärke und die Veränderungen bezüglich der Steifigkeit während der Experimente voraussehen.

Jan 1, 2003

By F. C. Canney

Geochemical prospecting seeks hidden mineral deposits by sampling for variations in the chemical composition of naturally occurring materials. Usually the samples are of soils and other products of weathering and erosion-surface materials extremely susceptible to contamination by human activities. Except when a survey is conducted well away from populated areas, contamination is an ever-present hazard. The program's success is particularly endangered when the contaminants are the elements sought; if these occur erratically throughout an area, spurious anomalies completely unrelated to mineralized areas can be formed. Evenly distributed contamination can be dangerous too, if it raises the background to such a level that true anomalies can no longer be easily detected. Suppose, for ex- ample, that in an area where the lead background is 20 parts per million the soil over a lead vein contains 1000 ppm of lead. Here the contrast would be 50 to 1, which is very satisfactory for geochemical surveying. Now if 1000 ppm of lead from some source were added evenly to the soil in this area, the contrast would be reduced to about 2 to 1, and the anomaly would no longer be readily detectable because a threshold of significance twice the value of the background is the minimum generally used for interpreting geochemical data.

Jan 2, 1959

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT The pervasiveness of high-fidelity video games raises expectations of quality, detail, and lighting in virtual reality (VR) applications. However, high-quality models of mining equipment and environments are often not readily available, and developers may not be familiar with the latest techniques, such as physically based rendering (PBR). Because a consistent aesthetic is critical for maintaining immersion and controlling visual stimuli in research as well as in training, researchers at the National Institute for Occupational Safety and Health (NIOSH) created an asset development workflow. This paper details this workflow, including precision modeling and PBR techniques as well as a rigorous review process. It also describes lessons learned in the creation of photorealistic VR assets. BACKGROUND Virtual reality (VR) describes the simulated experience generated by an assemblage of hardware and software that are used to immerse the user. Over many years VR developers targeted the development of virtual environments (VE) toward various purposes: entertainment, the treatment of phobias [1], rehabilitation [2], and training [3]. A large part of the VE development includes digital assets, where digital assets refer to the non-programmed elements including 3D models, audio, and user interface. Because vision provides nearly 10Mbps of data [4] and accounts for the majority of all sensory input combined [5], a focused effort on asset appearance in VEs is warranted. Furthermore, research has shown that higher-resolution imagery increases search performance and training transfer, necessitating high-fidelity assets [6, 7]. In addition to being visually appealing, it is important that the assets and environment are also dimensionally accurate and consistent in order to elicit appropriate responses from the end users as they interact with and among these items [8, 9]. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed VEs and digital assets under several research projects over the course of the last two decades [10, 11, 12, 13]. This work has provided researchers with a strong knowledge base for digital asset development. However, the assets themselves have had limited reuse value. Due to the extended timeframes and limited scope of these projects, the previously developed assets are not consistent in visual quality and dimensional accuracy. Moving forward, researchers wanted to minimize future development time and use of resources as well as adopt new asset development tools and game engine technology. Therefore, the aim of this paper is to document a new asset development workflow including geometry, materials, UV layout, and shader implementation combined with review steps in order to produce high-fidelity simulation assets that are accurate with consistent characteristics, using repeatable methodologies that are well documented.

Jan 1, 2019

By C A. Heinrich, J L. Walshe, V J. Wall

The Porgera Gold Mine, located in the highlands of Papua New Guinea, has produced over 5 million ounces of Au, since its opening in late 1990. The deposit is located within Upper Cretaceous Papuan Platform sediments approximately 25 km south of the Lagaip Fault, and is spatially and temporally associated with the 6 Ma alkaline Porgera Intrusive Complex.

Jan 1, 1995