Search Documents

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude runs to stills. Furthermore, the premise -the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By Wenbing Guo

The stability of strip pillar is the key to successful strip pillar mining. In analyzing the stability of the strip pillar, the width of yield zone must be determined. The determination of the width of yield zone has been an important subject for researchers. In this paper, the numerical method was used to study the relationship between the width of yield zone in strip pillar and coal recovery ratio. The results showed that as the recovery ratio increases, the width of yield zone increases exponentially. Accordingly, the formula for determining the width of yield zone was updated and the effect of changing coal recovery ratio on strip pillar deformation is presented.

Jan 1, 2006

By H. Maleki, G. Tetreault

This study was initiated by the Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room-and-pillar mining using a continuous miner (CM method) was economically sound, or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets" are left in longwall mines on one side of the mains, near outcrops and adverse geological conditions, or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included (1) analysis of the geologic, geo-technical, and economic factors that influence the recovery of small coal reserves, (2) analysis of historic changes in supply, demand, and coal prices, (3) development of typical cost models for room-and-pillar and longwall mines, and (4) development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR) as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modem longwall mines and thus is used to evaluate the

Jan 1, 2001

By David K. Hylbert

This study was designed to investigate roof falls in room-and-pillar drift coal mines and to determine geologic methods for predicting unstable roof conditions. The study area was located in Harlan County, Kentucky and the Bailey Creek (Harlan coal bed) and Highsplint (Darby coal bed) mines were selected for study. Correlations were made laterally between surface outcrops and within the mines using lithologic and trend analysis criteria. Lithologic criteria compared cyclic changes in roof strata. Results indicated that roof falls are associated with zones of weakness within or between five vertical cycles recognized. Abrupt lateral facies changes occur. In the Highsplint mine the roof was classified in four categories or conditions using 98 rib sections for control. Structure contour and isopach maps were used to project axial trends of the sandstone roof. A roof-fall zone was examined using ten NX cores taken from the roof and included lithologic, petrographic and clay mineral studies. At the Bailey Creek mine roof failure was caused by the heading direction being driven subparallel to paleochannel directions. Computer programs were used in trend analysis studies. Cross-bedding, paleo-channel trough axis and sole mark studies indicated a 350 discrepancy between surface and in-mine trough axes at Highsplint. A direct relationship between joint and "slip" frequency and direction with sandstone roll trends was found. Surface joints compared well with drainage Segments, hilt did not correlate with roof falls in areas of mines under overburden in excess of 600 feet.

Jan 1, 1977

A glance at the accompanying table reveals that for the first time in many years the industrial minerals field did not post significant gains in production. Gypsum, cement, sand and gravel, and crushed stone production-which are very sensitive to construction industry performance-barely managed to stay even, or in fact, declined slightly. Even barite production, in spite of increased oil and gas drilling, was off 5% in 1979 from 1978. Domestic fluorspar production continued to decline while imports, primarily from Mexico, South Africa, and Spain, rose 11%. Worldwide production of iodine (which is used primarily as a catalyst, animal feed additive, and in ink and colorants, stabilizers, pharmaceuticals, photographic film, and disinfectants) grew about 9% on a worldwide basis-from 10.75 Tg to 11.16 Tg. This does not include US production. The two US producers increased demand as apparent domestic production increased about 5%. Increasing energy costs and the transportation situation have had a prohibitive effect on the industrial minerals field. The critical shortage of railroad cars, according to consultant Neil Johnson, is due to several factors: • High capital investment rind interest rates needed to build new equipment, • Accidents, obsolescence, and failure to repair equipment reduced car availability, •Reduction in some train schedules due to fuel economy, and •Increased turnaround time as a result of new safety regulations. Railroad rates have increased an average of 7% per year for the past 10 years. Last year's increases were about 11.1% due to fuel costs and surcharges. Truck shipments have increased their penetration in certain areas of the southeast because of the shortage of box cars and the producers' demand for quick shipment. Some producers report a 15-20% increase in truck use. In the feldspar-mica area, which formerly made most shipments by rail, trucks are now used for about half the shipments. Marketing prices, as expected, increased due to higher costs for energy, power, labor, and supplies used in production. Estimated average price increases were about 10% which, in many cases, did not cover increased production costs. These factors-rising energy costs and the critical transportation situation-resulted in an unsatisfactory year for industrial minerals. Stanley J. Lefond Cnntrihuting Editor

Jan 5, 1980

By D. W. Hendriks, C. Daoust, K. V. Konigsmann

"The concentrator of Mattagami Lake Mines Limited commenced operation in 1963. It had been designed with instrumentation proven at that time. New control techniques were added in subsequent years.An on-stream X-ray analyser was installed in 1968. It provided circuit analyses for six years without the aid of a computer. In late 1974, control of the flotation circuit by computer was incorporated into the system. Flotation efficiency improved considerably, zinc"" recovery increased by one percentage point and concentrate grade by four-tenths of a percentage point. Reagent costs decreased modestly through reduction of copper sulphate consumption."

Jan 1, 1976

By Felix Torres

CVRD is one of the largest mining companies in the world. Adoption of new technology and improving operational efficiency are top company priorities. Initiatives in these areas have driven continuous company growth and an increased share price. During the first half of 2001, the company had a net profit of nearly US$ 500 M.

Jan 1, 2003

The efficiency of a coal mine ventilation circuit is usually measured by the ratio of the sum of the face quantities divided by the quantity supplied by the fans. Other types of systems use the power delivered to the power supplied to measure efficiency. This paper argues the case that the current measure may be inadequate and that by also looking at the power ratio, ventilation may be better managed. Problems associated with failing ventilation systems would be highlighted earlier so that crisis management could be avoided.

Jan 1, 2009

By R. Owen

An overwhelming amount of data can be collected around the blasting process. This information can include blasting product, pattern design, blast results, and routing. It is only when these data sources are combined in a concise and accurate form that they are of real use in determining the safety and economic implications of each parameter. Two key technological aspects of blasting are drill fleet management (DFM) and size fraction analysis (SFA). As these technologies are integrated as near-real-time measurement and QA/QC tools, the resolution and realization of blasting parameters is significantly increased. The Freeport-McMoRan Morenci Mine has integrated these technologies along with other existing database structures to create a responsive and sustainable tool for reconciliation, forecasting and parameter matching. This ability allows Morenci to customize blast patterns to meet the criteria most critical to each shot, whether the impact is influenced by routing and recovery, equipment maintenance or safety concerns. DRILL FLEET MANAGEMENT The current DFM was stabilized in its current form in mid 2009 after database and hardware maintenance met stability requirements. Currently the system is running on 12 production drills. The system receives pattern layout and is capable of semi-autonomous drilling over the entire district. The fleet is capable of drilling in highly altered intrusive units and hard granites through the range of sedimentary and volcanic units that comprise the Morenci District. The system brings a level of accuracy not achievable with earlier paint-marked patterns. Depth control is also increased along with more consistent wear and maintenance patterns due to semi-autonomous drilling.

Jan 1, 2011

By R Aseervatham

The fast tracked mine development strategy attempts to blend feasibility studies and engineering/commissioning functions into a streamlined process. In this compressed process, environmental issues are difficult to control with respect to the optimisation of operational environmental performance. This paper presents a standard mine development process with specific focus on environmental issues, and contrasts this against Rio TintoÆs recent fast track experiences on the Hail Creek project (Australia), the Baranj project (India) and the Gokwe North project (Zimbabwe).

Jan 1, 1999

By Julian Prada

Tunneling requirements are presenting designers with greater challenges. The design and construction of the 2000-ft long unidirectional twin highway tunnels for the approach to one of two bridges of the Louisville-Southern Indiana Ohio River Bridges (LSIORB) Project is no exception. Excavation under low cover, beneath an historic site, with each tunnel of 70-feet wide and 50-feet high dimensions will set precedents for US highway tunnel excavation size. To investigate ground conditions to supplement final design of the highway tunnels, an exploratory tunnel excavated through karstic limestone and shale will be located within the confines of the proposed final alignment. With the LSIORB Project, Jefferson County, Kentucky and Clark County, Indiana will have improved cross-river mobility between them. The Indiana Department of Transportation (INDOT) and the Kentucky Transportation Cabinet (KYTC) are developing the LSIORB Project jointly, in coordination with the Federal Highway Administration (FHWA). Section 4, one of six sections, as shown in Figure 1 is the East End Kentucky Approach and Connections to I-265. Key elements of Section 4 are the twin three-lane highway tunnels under the historic Drumanard Estate. The property is located on the north side of US Highway 42 (US 42) at the intersection with the Gene Snyder Freeway (also KY841) as shown in Figure 2. One aspect of the project consists of the excavation of an Exploratory Tunnel along the southbound alignment tunnel. At the time of preparation of this paper, KYTC has not awarded the Exploratory Tunnel Contract. This paper will focus on the planned geotechnical investigation program that will occur during excavation of the exploratory tunnel and how the design of the twin highway tunnels will incorporate the findings to achieve an innovative and efficient configuration.

Jan 1, 2008

By Douglas M. Smith, G. A. Maki

"The initial development of the massive potash deposits of the prairie evaporite formation took place over a decade ending in 1970. The potash mining and refining facility near Rocanvi11e, Saskatchewan was the 1ast of ten mines to come into production during that era. This operation, known as Sylvite of Canada Ltd., was designed to produce 1. 2 million short tons per year of KCl product in granular, coarse, standard and special standard grades.In 1977 the parent company, Hudson Bay Mining and Smelting, sold the Sylvite property to the Potash Corporation of Saskatchewan. Shortly thereafter PCS slated its new Rocanville Division for a two phase program of expansion. The first phase, completed in the spring of 1979, was relatively small, involving mill debottlenecking and additional equipment in the compaction circuit and the product and ore storage areas. The second phase was a major undertaking which included additional mining equipment and a new 300 STPH milling circuit. This work was completed during the fall of 1981 and has increased the Rocanville Division's nameplate capacity to two million STPY.Thickening equipment operating in the Saskatchewan potash industry is generally situated within the main refinery building or a separate insulated and heated structure due to the harsh winter climate and the need to closely control plant brine temperatures to ensure good flotation circuit performance. Since these thickeners process large volumes of slurries, conventional basin type designs tend to be large, ranging up to 150 feet in diameter or more. As part of the general effort to minimize capital costs, the potash industry has begun investigating the use of alternate high capacity, compact thickener designs. In this regard, PCS Rocanville undertook a program in 1978 to evaluate a Lamella™ Thickener and one other type of 'High Rate' thickener* as alternatives to a conventional design for the phase two expansion project."

Jan 1, 1983

By F. Taylor Ostrander

Some countries are infinitely poorer than others in mineral resources-despite the perfect equality of their political leaders ambitions. Compare the mineral poverty of Kenya and Tanganyika with the riches of Katanga Province and Northern Rhodesia. Compare Paraguay with Chile, There never has been any equality in the distribution of nature's wealth. Minerals cannot play any role at all in economic development where they don't exist, and there are bound to be differential rates of economic development where there are basic differences in the wealth of mineral resources available. Africa is my principal area of interest and I know that there is an unfortunate but widespread misconception about Africa's "vast mineral resources, "its "untapped mineral wealth." Why is it untapped? Why is it undeveloped?

Jan 1, 1963

By M. Roy

Safety and stability of underground coal mine workings are always in danger when opencast mines are operating in close proximity. A study was conducted to investigate the level of vibration generated from opencast blasting at similar distances on the surface as well as in the nearby operating underground coal mine openings. Eight blasts were performed and nineteen vibration data were recorded on the surface behind the opencast blasting face and also in underground openings at similar distances. It was observed that magnitude of vibration recorded on the surface were more than those recorded in underground.

Jan 1, 2007

Mineral exploration and mining in New Zealand has had almost five years of new legislation. The requirement for different consents is a challenging, time consuming, expensive exercise but in most cases the new procedure is working, although the matter of obtaining access to land is still a major issue. Priority is critical. After lodgment of an application for a minerals permit there are many other matters to address such as identifying land owners, occupiers and administrators, preparation of access applications, consultation and preparation of various resource consent applications.

Jan 1, 1996

By J. S. Coats, G. E. Patts, N. Hughes

Conventional sampling methods are known to suffer from the variable loss of fine gold by elutriation. Freeze sampling yields representative and quantitative data that, when combined with information on the sedimentology of gravel-bed rivers, may facilitate the development of improved dispersion models for source detection. It is suggested that freeze sampling may have particular application to the orientation stage of a large gold exploration survey

Jan 1, 1991

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008

By Don Thompson

It isn?t a lie if you don?t tell the whole truth The pictures National Geographic didn?t print Other photos National Geographic didn?t print?

May 1, 2009

Disasters are often tragic outcomes of high-risk technologies such as mines. In Australia, more mines are being developed every day, and the risk of disasters is ever increasing. No matter how effective our conventional safety devices are, there is a form of accident that is inevitable. These relate to accidents that result from æinteracting failuresÆ in a way that could not be foreseen by the designers. In so-called ætightly coupled production systemsÆ (processes that happen very fast, such as on a high producing mine) the risk is even higher and our risk controls mostly introduce some sort of a technological fix. While we are at the one hand attempting to control the risk, we are also introducing another level of complexity. Are we really controlling the risk? This is one of the fundamental questions that will be addressed in this paper: Do we have the ability within the mining industry and other industries to effectively prevent these catastrophes, or are we, on the contrary, faced with an increasing risk as a result of increasing complexities of our technology, management systems and practices. This paper will contend that perceived improvement in risk control is an illusion of activity, and that the likelihood of mining catastrophes may be exponentially increasing. Although the paper focuses on the mining sector many aspects may be applicable across a range of industries. This paper will further contend that we are applying the right solutions to the wrong problems. Our focus is technological and procedural, while our problem is one of production cultures ripe for error and failure.

Jan 1, 1999

By A. du Plessis

The study summarized in this paper focused on expanding existing South African mine closure cost calculation models to provide a new model that incorporates risks, which could have an effect on the closure costs during the life cycle of the mine. This research is important because currently there are a number of mines that do not have sufficient financial provision to close and rehabilitate the mines. The magnitude of the lack of funds could be reduced or eliminated if the closure cost calculation is done in a more risk-orientated manner. The model consists of an expansion of existing closure cost calculation models, by applying the Monte Carlo risk simulation technique to model influences of external and internal changes affecting closure costs. It is shown that the proposed risk-based model provides a way to understand better the implications of uncertainty on the closure costs.

Jan 1, 2006