Search Documents

By H. K. Lin

Residual cyanide in cyanidation tailings can be detoxified by its oxidation to cyanate, as in the Inco and Degussa processes. However, cyanate, the product of detoxification and other oxidation processes, may be reduced to cyanide in reducing environments, e.g., deepwater discharge of cyanidation tailings. This study shows that the reduc-tion of cyanate to cyanide occurs and that the reduction rate increases with decreasing solution redox potential. Solutions with lower pH favor the reduction rate. No significant difference was observed between the results of tests prepared with distilled water and seawater, and the presence of cyanidation solid tailings does not show an effect on the reduction. Because cyanate can be reduced to toxic cyanide, causing environmental concerns, the deepwater discharges of cyanidation tailings must be handled carefully.

Jan 1, 2008

By P. A. Riveros, W. D. Gould, R. Molnar, D. W. Koren, P. Bédard

This paper reports the results of the field demonstration campaign of a new process for removing and destroying ammonia from mining/ metallurgical effluent solutions. The 50-day campaign was carried out at a uranium plant in Saskatchewan, Canada. The process was developed by adapting and integrating two well established technologies: zeolite adsorption/ elution to extract the ammonia from the effluent stream and to produce a concentrated ammonia eluate; and conversion of the ammonia in the eluate to innocuous nitrogen by applying bacterial nitrification-denitrification (NH3 = > NO3 - => N2). The data show that reasonable target criteria were met, under very challenging operating conditions. Problem areas and possible causes for poor performance are identified. Preliminary and generic cost estimates of the process are also presented.

Jan 1, 2003

By Daniel Lozada

La unidad de producción polimetálica de Yauliyacu, ubicada en la localidad de Casapalca, Lima, tiene una presa de relaves en el paraje de Chinchan del mismo departamento. Sin embargo, dado que la presa nueva Yauliyacu culminaría su función y que la presa auxiliar Tablachaca no contaba con la suficiente capacidad de almacenaje, Centromin Perú evalúo otras alternativas para la ubicación y construcción de una nueva. De acuerdo al estudio realizado, se encontró que la quebrada de Chinchan era la más adecuada puesto que ofrecía mayor capacidad de producción y se descartó las de Corina y Tablachaca. En este sentido, el presente texto describe las características de la quebrada, el diseño del depósito de Chinchan, su proceso de construcción, la limpieza de fundación, el análisis de la estabilidad física y química, la implementación para mejorar la estabilidad de la presa, la mejora de calidad del aire en la zona del depósito, el programa de inversiones y el plan de cierre del relave.

Sep 13, 2001

By L D. Queen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Tifalmin porphyry copper district is located in the Star Mountains roughly 35 km north-east of the Ok Tedi mine. The district is a cluster of temporally and geochemically related porphyry copper deposits and their associated skarns. It covers an area of roughly 10 × 6 km and comprises at least three intrusions (Olgal, Futik and Kum Kom) where drilling has demonstrated the presence of porphyry copper mineralisation, and another three intrusions (Rattatat, Unfin and Pad 48) where porphyry copper mineralisation is strongly suggested by surface investigations and geochemical or geophysical signatures.Copper and gold mineralisation was first discovered in the area in the 1960s as part of the regional exploration program by Kennecott that located Ok Tedi. The mineralisation is associated with poly-phase porphyritic diorites, quartz diorites and tonalites that intrude the Upper Eocene to Middle Miocene Darai limestone and underlying Cretaceous to Eocene Feing Group. Radiometric K-Ar and U-Pb zircon ages cluster between 4 and 2 Ma for both the mineralised and post-mineral intrusions. In addition to porphyry-type mineralisation, variable amounts of calc-silicate and/or magnetite skarn occur near the contact of most of the intrusions. Mineralisation in the Olgal and Futik porphyries occurs as chalcopyrite replacement of mafic minerals and in a stockwork of micro-veinlets. Mineralisation mostly occurs in the intrusions but is also observed in hornfelsed siltstones and sandstones of the Feing Group on the southern margin of the Olgal intrusive body. Quartz veining is uncommon. Secondary magnetite is commonly associated with the highest copper and gold grades. Sericitic alteration is most prominent in the mineralised hornfels. Structurally, the area is dominated by syn- to post-mineralisation thrusting from the north. At least one of the deposits (Olgal) appears to be truncated at depth by a thrust fault.CITATION:Queen, L D, 2015. The Tifalmin porphyry copper gold district, Star Mountains, Western Papua New Guinea , in Proceedings PACRIM 2015 Congress, pp 357–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Abstract : The computation of reliability index or failure probability of slopes can be transformed into an optimisation problem. In high rock slope engineering, it is usually a multimodal optimization problem. The traditional optimization techniques are difficulty to find out the global optimal solution because of their easily falling into local optimal value. Recently, a new kind of bionic algorithm - ant colony algorithm (ACA) - has been used to solve this problem. In this paper, the structure of ant colony algorithm and the transfer probability of ants are modified to evaluate the failure probability of complicated slopes. A new adaptive ant colony algorithm (AACA) is proposed to determine critical slip surface and its corresponding failure probability of complicated slopes. A case study is given to verify the proposed approach. The results show that the presented method has obvious advantages compared with traditional methods. ZUSAMMENFASSUNG: Die Rechnung des Zuverlaessigkeitindexes oder der Zerstoerungswahrscheinlichkeit kann sich in einer Optimierungsfrage umwandeln, im Bauprojekt an hoehe Gebirgehang, handelt es sich meistens um eine Optimierungsfrage ueber Multi- Spitzenwert. Mit der traditionelle Optimierungsmethode ist es schwer eine umfassende Loesung fuer die Optimierung zu finden wegen des leichte Verfallens in Beschraenkung der Teiloptimierungsloesung. Mit dem neue Bionik- Algorithmus —— Ameisen - Kolonie- Algorithmus wird dieses Problem geloest. In diesem Text hat man eine Strukturverbesserungsloesung fuer das Ameisen- Kolonie -system und die Wahrscheinlichkeit der Ameisenkolonie erwaehnt, und damit wird man die Zerstoerungswahrscheinlichkeit des komplizierte Hangs feststellen. Mit dem neuen Ameisen- Kolonie- Algorithmus kann man die gefaehrlichste Gleitflaeche und die entsprechende Zerstoerungswahrscheinlichkeit herausfinden. Die in diesem Text beschriebene Methode wurde durch Praxis geprueft. Durch die Pruefergebnisse wurde es gezeigt und bestaetigt, dass der neue Bionik- Algorithmus vorteilhafter als der traditionelle Algorithmus ist. Résumé : Le calcul de l’indice la fiabilité ou de la probabilité de ruptures peut être transformé en un problème de l’optimisation. Pour le cas du génie des pentes de haut rocher , le problème se pose en général en l’optimisation de multi-crêtes. Les techniques traditionnelles conduisent facilement à la solution optimal partielle au lieu de celle globale. Récemment un nouveau type de bionique algorithmique a été appliqué pour la solution de ce genre de problèmes, c’est l’Algorithme Colonie de Fourmis. Dans l’article il est proposé de modifier la structure du système de la colonie de fourmis et la probabilité de transfert des fourmis en vue d’évaluer la probabilité de ruptures des pentes de haut rocher complexes, par ailleurs un nouveau algorithme adapté de colonie de fourmis est formulé pour déterminer la surface glissante critique et la probabilité de ruptures correspondante. Les techniques proposées dans l’article sont vérifiées à travers des expérimentations dont les résultats ont prouvé que les techniques présentées dans l’article sont évidemment meilleures que celles traditionnelles.

Jan 1, 2003

By J. Kim, H. Cho

The objective of the experiment was to investigate the efficiency of hindered-settling column in recovering carbon from anthracite. Two types of Korean anthracites were prepared for feed materials. Each sample was crushed and classified by size, and washability analyses were performed. Separation efficiency was evaluated under various operating conditions using a laboratory scale hindered settling column. Results showed that the carbon recovery was higher for the smaller sizes, but the purity of the product was better for the larger sizes. In, overall, 2-0.21mm particles of 40-45 % ash could be processed into about 20 % ash products.

Jan 1, 2002

By E. F. Perry

Simulated weathering tests are used to estimate leachate quality of rocks containing varying concentrations of pyrite and carbonates at mines. This study reports the inter-laboratory results from the third phase of a three part effort to develop a standardized, reproducible simulated weathering test for coal mine overburden. Initial development in phases I and II included evaluation of different test apparatus, effects of particle size, gas composition, leaching frequency and other variables. Phases I and II results are reported by Brady et al (2004) and Hornberger et al (2004). In Phase III, a standard column leaching protocol was used by eight commercial, government and university labs to test five rocks of different lithology, pyrite and carbonate content. Ideally, a simulated weathering test should have three characteristics to be useful in mine drainage studies. These include the capability to produce repeatable results, accuracy in simulating field conditions, and a concise test protocol of weeks to a few months. Simulated weathering, or kinetic testing, produces an effluent that simulates mine drainage composition. This can be beneficial for predicting mine drainage quality in comparison to whole rock analyses. The effluent may be tested for the same water quality parameters as the drainage produced during mining, such as pH, acidity, alkalinity, sulfate, iron, manganese, aluminum or other parameters. If the physical, chemical, and biological conditions of the kinetic tests are representative of those found in the mine environment, leachate composition may be used to estimate the water quality parameter concentrations produced during mining. Hornberger and Brady (1998), and Geidel et al (2000), compiled comprehensive chapters on kinetic tests for mine drainage prediction. These sources included: (1) a chronology and synopsis of scientific literature on these kinetic tests as they have developed over approximately 50 years, (2) discussion of the influence of physical, chemical, and biological processes, and (3) general guidelines for test procedures, data interpretation, and recommendations for further research to develop standard methods. Most of the kinetic test methods in use today were substantially developed and applied more than 40 or 50 years ago, including leaching columns (Braley, 1949), humidity cells (Hanna and Brant, 1962), Soxhlet reactors (Pedro, 1961), and field scale tests (Glover and Kenyon, 1962). . The most commonly used kinetic tests for mine drainage prediction are leaching columns and humidity cells. While these kinetic test methods and others have been used in hundreds of mine drainage studies as shown in Hornberger and Brady (1998) and other references (e.g. Sorini, 1997), they have rarely been used in coal mine permitting by either regulatory agencies or the mining industry. The major impediment to routine use of kinetic test methods is the variation in the design and operation of these kinetic tests, and lack of a standardized, accepted (e.g. by EPA or ASTM) test method. Interpretation and data comparison from different studies can be difficult. METHODS Five rocks of varying lithology, mineralogy, carbonate and pyrite content were collected in bulk from Pennsylvanian age coal measures in Pennsylvania, West Virginia and Indiana. Mineralogical composition of the samples was characterized in detail by Hammerstrom et al (in press) using optical, X-ray diffraction, scanning electron microscopy and electron microprobe methods. Acid Base Accounting (Sobek et al 1978; Skousen et al, 1997, Kania, 1998) was performed on bulk samples for % total sulfur (%S) as a measure of pyrite and potential acid generation, and Neutralization Potential (NP) as an index of carbonate content. A modified NP test, following the procedure suggested by Skousen et al, 1997 was also conducted for four of the five samples. The modified NP test accounts for initial acid consumption, Fe oxidation, and subsequent Fe hydrolysis by the iron carbonate mineral siderite. Siderite, even though it is a carbonate gives zero net alkalinity. Lithologic, Acid Base Accounting and general mineral composition data for the five rocks are shown in table 1 (see Appendix). Whole rock elemental analysis for major and trace elements was conducted on a sub-sample of each rock type. One laboratory was contracted to mix, homogenize, and size the bulk samples and prepare sub-samples for all the participating labs. Splits were sent to eight labs, and each organization was provided a detailed set of instructions for column assembly and leaching procedure. The protocol was developed based on results from phases 1and 2 of this study. The principal features of the column assembly are: a specific composition of particle size by weight (table 2), weekly leaching cycles, and incubation under humidified air containing 10% CO2. Figure 1 shows the column construction. [ ] The particle size distribution of the crushed rock sample is largely an artifact of the crushing process, rather than a natural systems process like the particle size distribution of a soil or an unconsolidated sedimentary deposit. The standardized particle size distribution, shown in Table 2, promotes operational consistency of the weathering test procedure, and provides better control over reaction kinetics. Large amounts of fine particles within specific zones of the leaching columns have been found to impede uniform fluid flow and/or gas flow (Hornberger and Brady, 1998). Regarding reaction kinetics, the importance of surface area to volume ratios has been described in a previous phase of this study (Brady et al., 2004), and significant differences in crushed particle size distributions and effective surface areas were found among the lithologic units. Standardizing the particle

Jan 1, 2009

Mining and metallurgical processing of gold and base metal ores often results in solid wastes and effluents containing high concentrations of arsenic. In addition, arsenic can be released to the atmosphere from gold roasters and base metal smelters. Speciation of arsenic in roaster products, in a stack sample from a copper smelter, in organic soils impacted by smelter emissions, and in an anaerobic effluent treatment system at a smelter site was determined in order to broaden our understanding of the nature and occurrence of arsenic in a wider range of metallurgical wastes. Micro-XANES spectra obtained from iron oxide particles forming in a gold roaster indicate preferential enrichment of As3+ species in maghemite-rich domains and microlayers. In comparison, haematite-rich iron oxide particles are dominated by As5+ species. It appears that maghemite is retarding oxidation of arsenic and its volatilisation during roasting. Arsenic occurs as both As3+ and As5+ species in a stack sample emitted from a Cu smelter, confined to fine-grained secondary product layers accumulated on the surfaces of spherical Cu particles. This is probably resulting from condensation of As species upon cooling following their volatilisation during the combustion process. Soil samples collected at various distances from the Cu smelter are dominated by As5+ species including monomethylarsonic acid and tetramethylarsonium iodide as the organic arsenic species. The presence of reduced As3+ species highlights the importance of organic material influencing the speciation of arsenic and mineralogical transformations taking place within the soil profile. The XANES spectra indicate that arsenic occurs predominantly as aqueous arsenite species in the anaerobic treatment system, contrary to the conventional thinking of As retention by the formation of secondary sulfides.

Jan 1, 2008

By H. M. Lawrence

"The land-pebble district, the larger of the two producing areas of Florida, is situated in Polk County and in the eastern part of Hillsborough County. About 80 per cent at the phosphate rock produced in the United States in recent years has been mined from this area. The phosphate ores, locally termed matrix. are beds of sands and clays containing the phosphate pebbles, considered to be Pliocene in age, derived by marine action from underlying Miocene phosphatic marls, and are covered by practically barren sands and clays that have been deposited more recently. Open-pit mining is practiced; hydraulic mining, which has been intensively developed in this district, is used exclusively for mining the matrix and, by some companies for removing the overburden, although drag-line excavators have become established and are proving economical for stripping operations. From the pits the matrix is pumped to adjacent washing plants for beneficiation. The product of the washers. after drying, enters the world markets as Florida pebble phosphate.In this district recovery of the phosphate pebbles by the washing plants has not been particularly effective in the past. The screening, designed to effect a seperation at about 20 mesh (0.033 inches), has not been well controlled. Washer rejects discarded to the waste dumps have contained appreciable amounts of material analyzing above the minimum commercial grade - 66 per cent B.P.L. (bone phosphate of lime). Such losses of commercial fractions should be considered avoidable, and have been discussed at length in a previous paper.3"

Jul 1, 1930

By Y. Mitani, M. Xie, G. Zhou, T. Esaki

The assessment of landslide instability and risk has become a topic of major interest for both geoscientists and engineering professionals as well as for local communities and administrations in many parts of the world. In this paper, based on a new developed Geographic Information Systems (GIS) grid-based 3D deterministic model and taken the slope unit as the study object, the landslide hazard is mapped by the index of the 3D safety factor. Assuming the initial slip as the lower part of an ellipsoid, the 3D critical slip surface in the 3D slope stability analysis is obtained by means of a minimization of the 3D safety factor using the Monte Carlo random simulation. The failure probability of the landslide is calculated by an approximate method in which the distributions of f,c and the 3D safety factor are assumed to be in normal distributions. The assessment of the earthquake triggered landslide hazard is done by the dynamic displacement analysis using the index of the Newmark displacement. All the calculations are implemented by a computational system call 3DSLOPEGIS in that a GIS component is used for fulfilling the GIS spatial analysis function. Besides the results of 3D safety factor and probability, the possible landslide body and boundary can be three-dimensionally quantitatively identified. L’ estimation des glissement de terrain et des risques impliqués est devenu un des principal sujet de préoccupation pour les géotechniciens, mais aussi pour les ingénieurs specialisés ainsi que pour les communautés et administrations locales dans de nombreuses région du monde. Dans cette étude, basé sur un modèle de maillage 3D et une approche déterniniste couplée au Système d'Information Géographique (SIG), étudiant la stabilité des versants , le lieu d'étude à risque est maillé suivant le facteur de sécurité calculé en 3D. En supposant que le glissement initial soit la partie inférieure d'un élipsoïde, l'analyse de stabilité pour le glissement critique 3D d'un versant 3D est obtenu grace à une minimisation du facteur de sécurité en 3D utilisant la méthode de simulation aléatoire de Monte Carlo. La probabilité d'un glissement de terrain est calculée par une méthode approximative, supposant la distribution de c, f et du facteur de sécurité 3D normale. L'estimation d'un risque de glissement de terrain causé par un tremblement de terre est faite grace à une analyse du déplacement dynamique suivant l'index de Newmark. Tous les calculs sont effectués par le biais d'un système de calcul appellé 3DSLOPEGIS dans lequel te GIS est utilisé pour gérer l'analyse spatiale. En plus de cela, les résultats du coefficient de sécurité en 3D, des probabilités, le terrain susceptible de glisser, et ses limites, peuvent être quantitativement évalués en trois dimensions. Die Bewertung von Erdrutsch-Instabilität und risiko sind zu einem Thema von großen Interesse für sowohl Geowissenschaftlern und Ingenieuren als auch von Gemeinden und Verwaltungen in vielen Teilen der Welt geworden. In dieser Arbeit, basierend auf einem neu entwickelten Geografische Informationssysteme (GIS) gitterbasierten 3D deterministischen Modell und mit der Böschung als Untersuchungsobjekt wird die Erdrutschgefahr durch den Index des 3D-Sicherheitsfaktors kartografiert. Unter der Annahme, dass der erste Rutsch der untere Teil eines Ellipsoiden ist, wird die 3D kritische Schlupfoberfläche in der 3D-Böschungsstabilitätsanalyse mit einer Minimierung des 3D-Sicherheitsfaktors mit der Monte Carlo Zufallssimulation erhalten. Die Fehlerwahrscheinlichkeit des Erdrutschs wird mit einer Annäherungsmethode berechnet, bei der die Verteilungen von f,c und dem 3D-Sicherheitsfaktor als innerhalb normaler Verteilungen angenommen werden. Die Beurteilung der Erdbeben-ausgelösten Erdrutschgefahr wird mit der dynamischen Verdrängungsanalyse mit dem Index der Newmark-Verdrängung gearbeitet. Alle Berechnungen werden mit einem Berechnungssystem mit der Bezeichnung 3DSLOPEGIS ausgeführt, bei dem eine GIS-Komponente zum Erfüllen der GIS räumlichen Analysefunktion verwendet wird. Neben der Ergebnissen des 3D-Sicherheitsfaktors und der Wahrscheinlichkeit kann der mögliche Erdrutschkörper und der Umfang dreidimensional quantitativ identifiziert werden.

Jan 1, 2003

By T Smith, J Hatley

With the increased focus on the need for more uranium mines, this paper presents the design process currently underway for the development of the Millennium deposit in northern Saskatchewan, Canada. This deposit, located 630 - 750 m below surface, will be accessed by two shafts and will be mined by blasthole stoping methods at less than 500 t/d. Mining grade will approximate two per cent U3O8 and mine life is expected to be six to seven years. The project is a joint venture between Cameco, AREVA and JCU. This paper discusses in detail methods used to predict worker radiation exposures, the methods used to monitor the work environment and procedures unique to the uranium industry necessary to minimise worker radiation exposures.

Jan 1, 2008

By B. J. Moore

The Bureau of Mines has estimated helium resources of the United States at 727 billion cubic feet as of January 1, 1979. These resources are divided into four categories in decreasing degrees of assurance of their existence: (1) Helium in storage and in measured natural gas reserves, 185 billion cubic feet; (2) helium in indicated natural gas resources, 150 billion cubic feet; (3) helium In hypothetical natural gas resources, 186 billion cubic feet; and (4) helium in speculative natural gas resources that makes up the remaining 206 billion cubic feet. The identified helium reserves, which are made up of that in measured and indicated natural gas categories, are further divided into depleting, non- depleting, and stored classifications. The depleting resources are those that are associated with natural gasfields that are, or will be, produced for the natural gas they contain. All of the helium in undiscovered natural gas resources are included in this classification. These depleting resources comprise 600 billion cubic feet of the total resource base. The nondepleting helium resources are estimted tototal 88 billion cubic feet. There is 39 billion cubic feet of helium in storage in Cliffside gasfield near Amarillo, Tex.

Jan 1, 1980

By D. M. Fraser

"Brunswick Mining and Smelting Corporation Limited operates two mines; one open pit (No. 6) and one underground (No. 12), approximately 20 miles south-west of Bathurst, New Brunswick. Both are massive sulphide deposits containing copper, lead, zinc and silver. The No. 12 property began operation in 1963 and is presently being mined at a rate of 3600 tons per day underground and is in the completion stages of an expansion to achieve 11,000 tons per day underground by the end of 1930.Originally at Brunswick Mining, acid mine drainage was added to tailings and neutralized by an excess of lime in the tailings. A conventional recycle system was established with a biostabilization pond for the treatment of thiosalts, a liming station and sludge settling area for neutralization of acidic water and a final reclaim pond with a pumping station for reclaim water.We found that not more than one third of the reclaim water could be used as it upset the flotation circuit every time it was used. It was established that the mine water and surface drainage were the cause due to oils and detergents in the water. It was also found that the biostabilization pond method Cf thiosalt treatment was not efficient for year round operation in our climate.In 1974, we reviewed the problems and began a 3 phase program to control effluents from the property:"

Jan 1, 1980

By Jim Dodd, Jim Paynter

"We would like to acknowledge the efforts of the following key people who helped to make this project a success.Ron Jung, instrumentation supervisor for the Golden Giant Mine, spent many hours reviewing process and instrument drawings, selecting instruments and providing hands on support during commissioning.Andy Keough, underground production supervisor for the Golden Giant Mine, was responsible for readying the underground distribution network for paste backfill.H.A. Simons Ltd. personnel who did an excellent job providing sound conceptual and detailed engineering.Fred Brackebusch, of Mine System Design who designed the paste backfill delivery systemPierre Lacombe, mill superintendent of the Louvicourt Mine, generously shared information and operating experience of their paste backfill plant.AbstractThroughout the 11 year history of the Golden Giant Mine, the primary backfilling method made use of consolidated rock fill. New backfill technologies have developed over recent years which now make it possible to use large quantities of fine mill tailings as backfill.In January of 1996, construction began on a new paste backfill plant at the Golden Giant Mine. Six months following, the plant was commissioned. This paper describes the design, commissioning and operational experience to date of the paste backfill plant."

Jan 1, 1997

By Brad Thrall, Howard Bradley, Michael Samuels

"LOCATIONViceroy Minerals Corporation owns and operates the Brewery Creek heap leach gold mine located approximately 55 kilometers northeast of Dawson City, Yukon Canada. Dawson was home of the Klondike Gold Rush 100 years ago. Upon startup in November 1996, the Brewery Creek Mine was the northernmost operating heap leach gold mine in North America and one of the most northern in the world. Located at 64"" 02' latitude, the mine is less than 300 km south of the Arctic Circle. Access to the mine is available at Kilometer 14 of the Dempster Highway, linking Inuvik, NWT and the Klondike Highway, 40 kilometers east of Dawson City. The immediate vicinity is the only part of Canada not glaciated in the Wisconsin advance, which has resulted in an oxide ore deposit due to approximately 80,000 years of weathering - an area unique in Canada.DESCRIPTION OF OPERATIONSIn order to utilize heap-leaching technology successhlly in an extreme northern climate, a number of design features were incorporated into the process flow sheet to operate on a year round uninterrupted basis. Winter temperature may dip below minus 50 ""C, demanding an approach to mining and leaching that is different from heap-leach operations in more temperate climates. Because of the severe winter temperatures, the mine operates approximately 2 10 days per year, while the leaching process is continuous on a year round basis. Run of mine ore (ROM) is placed on the heap beginning in mid April until late October. Overall gold recovery is projected to be 78% over a 325 day leaching cycle with annual production levels of 2.3 million tonnes of ore placed on the pad, with an average of 75,000 ounces of gold recovered per year. The recovery process utilizes conventional sodium cyanide leaching, carbon adsorption, high pressure stripping, thermal reactivation and acid washing, and on-site smelting.HISTORYFollowing a comprehensive governmental and public review of the proposed project, a Class A Yukon Water license was issued in August, 1995. Construction started in 1995 and leaching commenced in October 1996.A Socio-Economic Accord with the Tron Dek Hwech'in First Nations provides for employment, contract, and scholarship opportunities for First Nations citizens."

Jan 1, 1999

By J K. Wright

In recent years the production of steel from directly reduced iron ore pellets has expanded rapidly. However, continued growth will depend on an adequate supply of suitable raw materials for the various commercial gaseous and solid reductant processes now in operation. Although at present Australia does not produce pellets primarily for direct reduction, there is an increasing awareness of Australia's potential role as a supplier of high grade ores for export and/or domestic use. The properties and quality requirements of iron ore pellets made specifically for direct reduction (DR) are reviewed and the laboratory techniques and test methods used at the CSIRO Division of Process Technology for the evaluation of potential DR feedstocks are described. At the present time most of the evaluation tests for DR pellets are extensions of those designed for existing blast furnace (BF) burdens. In the case of some physical parameters such as cold compression strength, abrasion index and cold strength after reduction this extension is quite satisfactory. In the measurement of parameters such as reducibility, swelling and sticking tendency, however, it is necessary to develop meaningful standardized tests so that ores and pellets can be ranked for DR performance. To do this, data from the laboratory tests and from operating plants must be correlated.

Jan 1, 1980

By Willem Le Roux

1.1 Section 47(1) of the Mine Health and Safety Act, 29 of 1996 (?the MHSA?) establishes a Mine Health and Safety Inspectorate which is administered by the Chief Inspector of Mines. The Mine Health and Safety Inspectorate is part of the Department of Mineral Resources. The Chief Inspector is appointed by the Minister of Mineral Resources (see section 48(1) of the MHSA). 1.2 The Chief Inspector must, amongst other things, ensure that the provisions of the MHSA are complied with and enforced, and that all the duties imposed upon the Chief Inspector and the other Inspectors of Mines in terms of the MHSA and any other law are performed. The Chief Inspector of Mines must appoint Principal Inspectors of Mines and Inspectors of Mines to assist him/her to discharge his/her duties (see section 49(1)(a) and (c) of the MHSA).

Jan 1, 2011

By Robert Stefanko

The growing demand for energy during the post World War I and World War II periods has prompted underground coal production to increase rapidly. This has been met primarily by mine mechanization, resulting in the development and application of new mining machine types. Correspondingly, the total connected horsepower of each machine as well as the number employed has enlarged rapidly since 1950. (2,3,9,14,16,17) Electrical consumption for each mine has also grown. In the early years of mining electrical applications, only d-c power was utilized underground. Yet, d-c machine limitations were soon realized, and many a-c systems were substituted to permit economic and efficient utilization of a-c distribution and motors. Due to the attractive torque characteristics, ease of distribution and speed control, several traction applications have continued to be powered by d-c motors. The result has been the now prevalent use of mixed a-c/d-c mine power. However, augmented electrical power employment seems to have added to underground coal mining electrical accidents.

Jan 1, 1974

By Marvin V. Damm, Lloyd C. Venburg, Dan Sokol

Analytical and computer models are used to evaluate information obtained from existing data and investigation programs so mine water control systems can be designed and developed. These models allow the geohydrologist to predict the amount of groundwater inflow and the impact of dewatering and stream diversion on the hydrologic regime, and to determine the schedule and equipment needed for mine dewatering. This article describes uses of the model and the essential components necessary to construct an effective and practical one. Hydrologic models are constructed to determine the extent that mining activities will affect the ground water and surface water hydrologic regime. These models range from basic analytical, mathematical models to the more sophisticated finite difference and finite element groundwater models. Many factors determine the degree of sophistication, including the mining stage, the complexity of the hydrologic regime, the mining process, and regulatory requirements. Model Uses The geohydrologist and engineer construct models so the entire ground and surface water handling and supply system can be integrated and optimized. These models can provide the following data: • Information for water balance studies-the entire hydrologic regime for the area, including precipitation, transpiration, evaporation, infiltration, runoff, and the effect of geologic features. • Data on seepage rates during mining. • Information to design the depressurization and dewatering system, including water well spacing, location of sumping systems, need for grout curtains, and possible horizontal drain and underdrain locations. • Data needed to schedule dewatering and mining operations. • Prediction of initial and long-term impacts of mining and dewatering, including local and areal drawdowns, effects on existing wells, and modifications to the surface-subsurface hydrologic regime. Potentiometric surface maps and hydrographs can be prepared from these data. • Prediction of the effect of discharge from the water control system on the surface hydrology and data input to design systems for water discharge, storage, recharge, or reinjection. The results of a computer study that illustrates the effect of dewatering and reinjection into an aquifer to confine the cone of depression are shown on the accompanying figure. • Information to forecast potentiometric surface recovery after mining ceases. The accompanying figure shows the pumping and reinjection rates in a program that is adequate to dewater a mine and permit the recovery of potentiometric levels to approximate premining levels after mining ceases. • Documentation and design information for monitoring systems to be installed during all mining phases. • Water quality predictions and geochemical changes, including the possibility of brackish or saline water intrusion because of extensive dewatering or depressurization operations. • Documentation and data for acquiring permits from regulatory agencies. Model Input Program For any model to be effective, detailed hydrologic and geologic data must be gathered from a review of existing information and from an investigative program. These data should cover entire model limits. Data updating, revising, and refining should occur as new information is received from the investigation and monitoring programs, and from the mining operation as it progresses through the pre-mining, mining, post-mining, and reclamation

Jan 8, 1982

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude run to stills. Furthermore, the premise the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942