Search Documents

By M. T. Spyridopolous, S. J. Neethling

"There has been a significant research interest in the stability of single thin films, including prediction of their failure based on disjoining pressure and film thickness experiments and DLVO theory. It is, however, notoriously difficult to correlate information on the failure of a single thin film with measurements of foam stability. This is particularly true for the prediction of dynamic foam stability indicators, such as equilibrium froth height and surface bubble size.An alternative experimental approach to studying single thin film failure for predicting foam stability is to measure directly the coalescence probability between two approaching bubbles in a surfactant solution. These experiments can be performed under different chemical and physical conditions by using a micromanipulator that allows variation of bubble size, surfactant concentration, approach velocity and stationary position. The interface radius of curvature, the time to coalescence and the film area between the bubbles can be measured directly using image analysis.In a foam, the force exerted on the thin film separating two bubbles depends on the local radius of curvature of the Plateau borders and vertices, which depends in turn on the local liquid content. Results from different bubble sizes in the micromanipulator therefore translate into regions of different liquid content in the foam. Small bubbles, having a high radius of curvature correspond to the low-liquid content (Polyhederschaum) region higher in the foam, and large bubbles to the wetter (Kugelschaum) region closer to the liquid-foam interface. Experiments with different holding distances between the bubbles correspond to differences in bubble size in the foam, as the size of the film between the bubbles varies."

Jan 1, 2003

By Kal Sastry, Anshuman Prasad

"Agglomeration of fine iron ore concentrates is carried out in two steps:Balling, which refers to the production of green pellets by tumbling moist fines powders in drums, discs, or cones, and Induration, which refers to the subsequent thermal treatment of the green pellets in straight grate or grate-kiln systems.This paper addresses computer simulation of balling or green pelletization step. The process of agglomeration from a mechanistic point of view can be described as the transformation of moist feed to well-formed species or pellets. The moist feed is composed of fines of infinitesimal size while well-formed species are of finite size and number. These well-formed species undergo changes in their size and number through different mechanisms of agglomerate formation and growth. Nucleation, coalescence and layering are the three main mechanisms that describe the formation and growth of granules during an agglomeration process. A population balance equation enables quantitative description of the evolution of agglomerate size distribution due to the occurrence of each of the mechanisms.A numerical solution for the population balance model is necessary and is obtained by the use of a sizediscretization approach. The numerical solutions provide a suitable basis for the analysis of the agglomeration process. Also a coalescence kernel has been introduced that is capable of describing the simultaneous occurrence of nucleation, coalescence and layering mechanisms. The effect of feed moisture has been described using a moisture factor with an exponential functional dependence on the moisture content. The effect of the feed to seed ratio is modelled by the introduction of a crowding factor. It was assumed that only the feed particles which are much more in number experience a crowding or restricted in space interactions effect. A computer simulation program has been developed with MATLAB as the simulation language."

Jan 1, 2003

The Small Pebble Process for Reducing Ball and Power Consumption in Secondary Grinding Ball mills are used widely for secondary grinding. A mixture of ball sizes can be used to optimise grinding efficiency, but the use of balls smaller than about 30 mm in diameter is not normally viable, particularly when alloy steel is required. Preliminary testing of the grinding efficiency of various combinations of 40 mm steel balls and crushed stone in the size range 7 to 25 mm was carried out in a 300 mm diameter mill, which has accurate power measurement.The primary interest was to assess the potential benefit of adding small pebbles (from a primary circuit crusher or mill) to a secondary ball mill, to reduce ball consumption and to improve grinding efficiency. The optimum proportion of pebbles was found to be about 25 per cent by volume. This mixture produced about the same amount of fines as balls alone, but with lower power consumption, due to the lower density of the pebbles. The net result was a 12 per cent saving in power and a 25 per cent saving in ball consumption. The production of fines was partly due to pebble wear. The use of portions of 15 mm balls, (ceramic and steel), was also tested for comparison. A few batch pilot-scale tests were conducted in a 1.2 m diameter, 0.31 m long mill to test the viability of the pebbles at a larger scale. The pilot-scale tests confirmed the reduction in power and that the rate of production of fines was the same as that obtained with balls. The same residence time was used and this implies that pebbles can be added to an existing full-scale ball mill, with no loss in capacity. Samples of secondary mill feed and pebbles were obtained from a copper mine and the steady-state consumption of pebbles was determined by locked-cycle laboratory-scale tests. These tests demonstrated that mill power could be reduced by up 13 per cent and that the consumption of 40 mm balls could be reduced by up to 38 per cent, while maintaining the same throughput and product size. The rate of pebble addition was about 4 per cent of the primary circuit feed rate. Application has been made for patent protection.

Sep 13, 2010

By Luis Giraldo

The installation procedure of fully grouted rebar bolts requires that the bolt be pushed through the resin grout until it is fully inserted in the borehole. Resin grout is a highly viscous fluid that is forced to flow through the annulus between the bolt and the borehole as the bolt advances. Variables such as bolt insertion speed, bolt vs. borehole diameter and grout viscosity determine the magnitude of the pressure generated ahead of the bolt tip. Under weak rock conditions, the magnitude of the pressure of bolt insertion is often sufficient to initiate hydraulic fracturing along joints or bedding planes that allow injection of grout into the strata leading to significant loss of bolt encapsulation. The grout pressure front has also been linked to gloving, a bolt installation problem that reduces bolt effectiveness. A series of tests were conducted to characterize the pressure of bolt insertion during bolt installation under various conditions. Analysis of the data shows three distinct stages of pressure build up during bolt installation. Understanding of the mechanisms involved may allow development of strategies for controlling the pressure buildup and its negative impact during roof bolting under weak rock conditions.

Jan 1, 2006

Study on Separation Technology for Copper-Molybdenum Collective Concentrate

Sep 13, 2010

By H. Rossmanith

This contribution introduces the fundamental concepts of wave propagation and fracture mechanics which form the basis of electronic blasting, i.e. precise initiation timing using electronic detonators. The concept of Lagrange diagrams will be frequently used for the calculation of the delay time between blast-holes in a row and rows of blast-holes. The effect of burden and structural geology will be briefly touched. It is found that the advanced blasting technology based on the use of electronic detonators introduces a change of paradigm. It will be shown that knowledge in wave propagation and fracture mechanics is essential for the successful application of the new blasting technique in industry. In particular, the delay time, the wave speeds in the rock mass, the shape of the wave pulse and the acoustic impedance mismatch have become decisive parameters in advanced blasting. Utilizing the wave speed and wave shapes of detonations, large scale tests Utilizing the wave speed and wave shapes of detonations, large scale tests in various countries (Australia, Chile, etc.) have shown that optimal delay timing requires shorter delay times in conjunction with allowing for a wider drilling pattern and the use of a reduced amount of explosives, i.e. a lower powder factor. This seemingly contradictory arrangement is fully justified by using scientific principles in blasting, and converting blasting from an art to a scientific discipline.

Jan 1, 2003

By John C. Holtz

Interest in the possibility of using Diesel6/ engines for haulage power in mining and tunneling is increasing in the United States, owning largely to the reported successful use of Diesel locomotives in European coal mines and to the comparatively recent development of automotive Diesel engines in this country. The extent of this interest has been evidenced to the Bureau of Mines by numerous requests for information as to the factors that must be considered if Diesel engines are to be used safely underground.

Jan 1, 1940

By Osamu Taki

This paper presents the system, the strength of column, the design concept, and the applications with four case histories from the past project as the general aspect of Geo-Column (trade mark of single soil-cement column by SCC Technology, Inc.). In the system, it shows the installation process and drilling/mixing tool with the mixing process. In the design concept, it shows how to design Geo-Column against the vertical and horizontal load. Finally, it shows the applications with four case histories, (1) building mat foundation, (2) isolated foundation on the pedestrian bridge, (3) bridge spread footing and slope erosion control wall in the channel, and (4) cut-off wall and shoring wall in the underpass roadway to the railroad.

Jan 1, 2000

By D. E. Welcome, T. W. McDowell, R. G. Dong, S. F. Wiker

Workers using vibrating hand tools have the potential for developing health problems associated with repeated forceful actions and exposures to hand-transmitted vibration. Hand-arm vibration syndrome (HAVS) and other hand-arm system disorders have been associated with such exposures.1-2 To better assess health risks, comprehensive evaluations of these exposures must include quantitative assessments of hand-tool coupling forces; unfortunately, no standardized method for quantifying hand forces exists. Handle instrumentation may be ill-suited for some field environments. Psychophysical force-recall techniques may provide alternatives to handle instrumentation. A thorough understanding of the effects of vibration and other factors on force-recall accuracy and reliability is important before such methods are applied in risk assessments. Methods In this study, the effects of vibration and other factors on the accuracy of psychophysical force-recall were explored in two experiments. Twelve male subjects participated in the first experiment. The second experiment employed 20 participants (10 female, 10 male). In each experiment, participants applied specific grip and push forces to an instrumented handle mounted on a shaker system. Participants were exposed to sinusoidal vibration at frequencies that ranged from 0 Hz to 250 Hz. Three levels of applied force (low: grip = 15 N/push = 25 N, medium: grip = 30 N/push = 50 N, and high: grip = 45 N/push = 75 N ) and two levels of vibration magnitude (low: ANSI 4-8-hr limit and high: ANSI <0.5-hr limit)3 were examined. During the vibration exposure period, participants were provided with visual feedback while they attempted to “memorize” the applied grip and push forces. At the conclusion of the vibration exposure/force memorization period and a controlled rest period, the participants tried to duplicate the grip and push forces on a non-vibrating handle without the aid of visual feedback. The effects of different vibration frequencies, vibration magnitudes, and grip and push force levels were tested in a random order from trial to trial. Results Participants tended to overestimate grip and push forces. Depending on exposure conditions, error means ranged from 2 N to 10 N. The ANOVA revealed that force-recall errors for exposures between 31.5 Hz and 63 Hz were significantly higher than those at other vibration frequencies (p < 0.05). The frequency effect is depicted in Figure 1. Error means were greater when participants were exposed to the higher vibration magnitude (mean = 9.1 N, 95% CI = 8.2-10.1 N) when compared with the lower vibration magnitude (mean = 4.9 N, 95% CI = 3.9-5.8 N) (p < 0.05). The effect of vibration magnitude is shown in Figure 2. The average error for

Jan 6, 2006

By Walter W. Kaufman

This report summarizes a study conducted to establish the nature and impact of regulations governing disposal of refuse from underground coal mines. The regulations affecting refuse disposal in eight major coal producing states are collected, summarized and reviewed. Federal regulations applicable to refuse generated by underground coal mines are also included. Common refuse disposal practices are discussed as are the refuse quantities generated annually in each study state. Technical requirements of regulations are discussed acid presented in appended tables. Economic implications are also assessed through cost analyses of three major types of disposal processes. The report also includes an assessment of future trends in regulation and refuse generation plus a series of recommendations concerning potential improvements in both the regulatory and refuse disposal processes.

Jan 1, 1978

By John C. Holtz

Interest in the possibility of using Diesel6/ engines for haulage power in mining and tunneling is increasing in the United States, owing largely to the reported successful use of Diesel locomotives in European coal mines and to the comparatively recent development of automotive Diesel engines in this country. The extent of this interest has been evidenced to the Bureau of Mines by numerous requsts for information as to the factors that must be considered if Diesel engines are to be used safely underground.

Jan 1, 1940

By Anthony Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990?s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine?s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Jan 1, 2007

By J. P. D. Strydom

The transmission of excessive vibration to the human body can cause physical stress that may result in crippling pain or permanent disability. Rock drills are known to transmit high levels of vibration that are difficult to attenuate through conventional approaches to vibration isolation. However, it can be shown that once the ISO frequency weighting has been applied, most of the vibratory effect of the rock drill?s motion is concentrated at the drill?s operating frequency. This observation opens the way for utilizing a concept known as vibration absorption, aimed at attenuating the rock drill?s vibration. In essence this entails using the inertia of a secondary vibratory system to counteract the motion of the handle. This article documents an investigation into the use of such an absorber for attenuating rock drill vibration and demonstrates the feasibility of such an approach. A mathematical model of such an absorbing handle was developed and used for design studies. Based on these investigations an experimental prototype model was manufactured and tested. A significant reduction in vibration levels could be achieved.

Jan 1, 2002

By S Arai

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Podiform chromitites are commonly found in the Moho transition zone to the mantle section of ophiolites, but have been very rarely found from the current ocean floor, even though some ophiolites are considered as a slice of oceanic lithosphere. One of the factors controlling podiform chromitite formation is the chemistry of host mantle peridotite; an intermediately refractory harzburgite is the optimum host for chromitites. This harzburgite represents the most common lithology of the oceanic lithosphere, where the peridotite-melt reaction, which is another condition, is possibly common there. The oceanic lithosphere mantle is thus a good host for podiform chromitites. The apparent rarity of documented oceanic chromitites is solely due to under-sampling of mantle materials from the fast-spreading ridge and the segment centre of slow-spreading ridges. Some ophiolitic chromitites formed not from genuine mid-ocean-ridge basalt (MORB) but from wet MORB due to the situation of typical ophiolites, which formed not at ordinary mid-ocean ridges but at supra-subduction zone spreading centres.CITATION:Arai, S, 2015. Podiform chromitites do form beneath mid-ocean ridges , in Proceedings PACRIM 2015 Congress, pp 465–468 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S. K. Gilman

Zircon (ZrSiO4) sand production of about 1.1 Mt/a(1.2 million stpy) predominates the global supply of zirconium minerals. Baddeleyite (ZrO2) contributes less than 1 percent of supply. Zircon is almost exclusively produced as a co-product from the mining of titanium minerals, mainly from mineralized beach sands. In 2004, there were a number of new projects under consideration that were more dependent on zircon revenue than for titanium minerals. This reflected sustained higher zircon prices and forecast ongoing supply shortages in the absence of major new discoveries.

Jan 1, 2005

By Wen-Chieh Cheng

Two bored piles with base grouting are loaded axially and the results are used to compare with numerical analyses. One compressive pile with a diameter of 2 meters is drilled through clay deposit and into bedrock to a depth of 13.7 meters. One tensile pile with a diameter of 1.5 meters is drilled through the same clay deposit and into bedrock to a depth of 17 meters. Both piles are installed with monitoring system such as rebar strain meters, concrete strain gauges and extensometers. The monitored data during pile load test are used to obtain average frictional stress (t) a displacement (z) curve, pile tip bearing (q) as well as pile head load (p) and a displacement (s) curve. FLAC3D is used to simulate the pile loading and base grouting. The soil and bedrock are modeled with Mohr-Coulomb. The parameters of the constitutive law are established from soil biaxial tests and rock bore hole deformation tests. The pile is assumed as an elastic body. The interface element is used to simulate the pile/soil interface and pile/rock interface. The numerical results are compared with the pile load test in terms of t-z curve, q-z curve and p-s curve. Finally, the pile base grouting is simulated and the uplift is analyzed. The result from this study is promising and the numerical modeling is successful.

Jan 1, 2006

By C. L. Liao

The chief experiences for constructing deep tubular columns foundation under deep water are as follows: 1. P.C. tubular columns were sunk inside the caisson. 2. P.O. tubular columns of 3.6 M. diameter were sunk thru thick soil layer to a depth of 47 M. by vibrators. 3. The double wall steel cofferdam was sunk thru soil layer to a depth 31.3 M.. 4. Bore the bedrock with rotary drill succesfully. According to the successful experiences mentioned above, the deep tubular columns foundation may be constructed beyond 100 meters.

Jan 1, 2010

By Bruce Notthup

Using a Three Dimensional Laser Profiler, persomrel from Austin Powder were able to determine drilling patterns for use in underground mine Room and Pillar blasting operations, The faces had got out of alignment, causing concave faces across the 100 feet wide, 28 feet high tunnels. This was leading to poor drilling and poor blasting results. By profiling the faces, modifications could be made to the drilling pattern to help gradually straighten the faces. The Laser Profiler was also used to check the accuracy of collaring the holes and also perform post blast surveying of the positions of the bootlegs. This allowed recommendations to be made to improve drilling operations at the face. In addition, other volumetric calculations could be performed using the systems’ surveying software, all a lot more easily and quickly than by standard methods.

Jan 1, 1994

By P. S. Capper

"Generally speaking, the most intensive efforts at dust control in the mining industry have, in the past, been concerned with underground operations and where uranium ore or high silica material is processed. In the past several years, Stoop Rock has made Intensive efforts to reduce dust levels in it's Iron ore pelletizing complex. There have been no great engineering break-throughs with regard to dust control in such plants, and certainly no new engineering techniques have had to be applied at Steep Rock. This paper deals with how significant improvements in dust levels have been achieved through minor modification to dust collectors and ventilation units, improvements in operating practices, and education of supervisors and hourly personnel.PROCESS DESCRIPTIONSteep Rock Iron Mines is located 120 miles west of Thunder Bay near Atikokan. (fig. 1) Run-of-mine ore is pelletized along with some -1"" concentrate that has been processed in the concentrator (a summer operation only), which utilizes gravity separation to upgrade a mechanical mixture of ore and waste."

Jan 1, 1976

By Edwin B. Eckel

This paper, based on brief field examination and on data supplied by the operators, records the condition of the Italian mercury industry as of March 1945, not long after Italy&apos;s collapse. Except for the once-Italian but now Yugoslavian Idria mine near Trieste, virtually all the known mercury deposits are in the Monte Amiata district in Siena and Grosseto Provinces, 75 miles north of Rome. This district contains the Abbadia San Salvatore. the Siele. the Argus, and the Cerreto Piano mines besides numerous prospects and unproductive mines. Under pressure from Germany the principal mines were highly productive during the early part of the war, but production fell off long before its end. All of the mines were damaged in some way at the German withdrawal but by September 1944 the Abbadia had resumed production and several others were only lacking power by the early spring of 1945. The Monte Amiata district is characterized geologically by a thick series of sedimentary rocks that range from Triassic to Eocene in age . and are surmounted on Monte Amiata itself by a thick cap of extrusive trachyte. Bodies of travertine and of landslide detritus, younger than the trachyte, are rather widespread. The structure is complex and little known but most of the ore deposits seem to lie along or near a major, north-trending fault or on associated cross-fractures. Cinnabar is the only important ore mineral and clay minerals are by far the most abundant products of hydrothermal alteration. A southward increase in the amount of stibnite, relative to cinnabar, suggests horizontal zoning. The grade of ore ranges from 0.60 to 3.0 Pet and the reserves, as compared with those in American mines, are enormous. Even in the face of war-time scarcities, the mines are remarkably self-sufficient and labor is plentiful, but the costs of production are estimated to be not greatly below those of the better American mines. Notes on the principal mines, on the mining and metallurgical methods, and on the manufacture of synthetic cinnabar are included in the paper. Introduction With but few brief interludes, Spain and Italy, including the Idria mine near Trieste, which has passed from Austrian to Italian to Yugoslavian hands in the Past 3 decades, have led the world in the production of mercury, or quicksilver, for many centuries. Despite their enviable position with respect to the supplies of a metal so essential in both war and peace, there is a notable lack of up-to-date information in America on the mercury industry of either country. Duschak and Schuette&apos; and Schuettez,3 give by far the best summaries in English known to the writer, but the latest firsthand report cited by them on the Italian mines was published in 1915.&apos; Having been deeply interested in the geology and economics of mercury for several years, the writer naturally felt most fortunate in being the to obtain enough firsthand information on the Italian industry to fill at least a few of the gaps in our knowledge. The opportunity came during the war, soon after this industry, together with the rest of Italy, had capitulated to the Allies. Many of the facts presented here are thus definitely "dated," but others are of less transitory nature, and even the dated facts should be of interest in showing the strength and

Jan 1, 1949