Search Documents

The French research institute, INERIS, requested the assistance of the CSIR?s Division of Mining Technology in developing further precautionary measures against explosions in their collieries. In response to this approach, an on-board active suppression system was adapted to meet their mining requirements. This system is used on tunnelling machines in Germany where the machine is positioned in the middle of the tunnel, which is therefore not much wider than the machine itself. With this configuration, the machine is never away from the tunnel face during the cutting cycle. As a result, the possible volume in front of the machine of combustible gas requiring suppression is less than 50 m3. In South Africa this technology has been adapted to suit a two-cut mining method which entails greater distances from the face and thus much larger volumes of methane mixtures requiring suppression. The particular configuration of the Explo-Stop® system being investigated required the suppression of possible methane ignition volumes of up to 180 m3of a 9% per volume methane/air mixture. The volume is a consequence of the large cross-sectional area of French underground workings and of the two-cut mining method used in France. In order to take the second cut in the coal seam, the machine is pulled back a maximum distance of 4 m, leaving an air pocket in which gas can accumulate. The machine-mounted system is required to effectively suppress any flame ignited by such a large accumulated volume of methane. The results of the protocol tests done at Kloppersbos showed that the system was capable of suppressing all simulated methane ignitions for the prescribed conditions. This was achieved with a temperature increase of less than a 100°C at the operator?s position and without any flame being detected at this position.

Jan 1, 2001

By J. E. Urosek, K. L. Cashdollar, D. A. Beiter, G. J. Shemon

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on mine ventilation stoppings at the NIOSH Lake Lynn Experimental Mine (LLEM). After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to mitigate or eliminate future occurrences. As part of these post-explosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, are documented as evidence of the strength and the direction of the explosion forces. The LLEM data showed that a total pressure of 52 kPa (7.6 psi) destroyed the solid concrete block stopping, ~36 kPa (~5.2 psi) destroyed the hollow-core concrete block stopping, and 9 kPa (1.3 psi) destroyed the steel panel stopping. These results will assist investigators in determining the explosion forces that destroy or damage stoppings during actual coal mine explosions.

By William R. Yernberg

A conference on coalbed and coal mine methane was held March 27 and 28, 2000, in Denver, CO. The conference, organized by the Strategic Resource Institute, was attended by leaders in the coal mining and gas energy industry. The conference focused on the recovery of methane from coal beds as an energy resource and the removal and utilization of coal-mine methane (CMM) related to underground coal mining. The two-day conference discussed methane resources around the world, methods of recovery, methane markets, underground coal mining, health and safety issues and environmental issues related to methane. The consensus among the presenters is that the future looks promising for coal bed methane (CBM) and CMM.

Jan 1, 2000

By G J. Lyman, S A. Tittlemier

International regulations exist to manage the concentrations of mycotoxins such as Ochratoxin A (OTA) and deoxynivalenol (DON) in grains and prevent health risks from excessive exposure to OTA and DON. Since the permitted levels of these mycotoxins are very low (existing maximum levels are in the range of 5 ppb for OTA and 1–2 ppm for DON), sampling for these mycotoxins is potentially challenging. Given that the distribution of infected kernels in a consignment of wheat can be highly heterogeneous, detection by current sampling methods is subject to a high variance. Furthermore, the concentrations of mycotoxins in individual kernels vary over orders of magnitude, intensifying the heterogeneity of the bulk grain.In these circumstances, there is much interest in developing sampling plans that inform regulatory agencies, and mitigate the risk of misclassifying grain shipments as compliant or non-compliant within the global grain trade, when correctly implemented.Experimental data from laboratory and field studies describing individual wheat kernel concentrations of OTA and DON were combined with experimental data describing the variance due to the analytical methods used for OTA and DON to calculate the sampling distribution for wheat having various levels of contamination. This work has focused on quantifying the heterogeneity of samples at the point of submission for analysis and within subsequent sample preparation to arrive at total sampling distributions that include uncertainties due to the intrinsic heterogeneity and the analytical uncertainties. The sampling uncertainty that relates to the difference between the primary sample analysis and the true lot analysis is not included as it has been dealt with elsewhere.CITATION:Lyman, G J and Tittlemier, S A, 2017. The sampling characteristics of grains contaminated by mycotoxins, in Proceedings Eighth World Conference on Sampling and Blending , pp 281–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

To improve the air quality in large-opening stone mines by developing better ventilation techniques, including appropriate fan selection in conjunction with air-coursing methods. Background Stone mines are the most common underground large-entry mines in the United States. Data from the Mine Safety and Health Administration (MSHA) for the year 2000 indicate that there were 162 active nonmetal underground mines in the United States, of which 117 were stone mines. Many underground stone mines are drift mines developed from previous quarry operations. Typically, these room-and-pillar mines have entries that are 20 ft or higher and at least 40 ft wide. These large dimensions lead to a very small ventilating pressure loss, even when significant air quantities move through the mine. This is especially true of drift mine operations where ventilating pressure losses of <0.25 in w.g. are common. Underground stone mines with shafts that are<200 ft deep typically have ventilating pressure losses that are <2 in w.g. The pressure losses through these mines are much lower than those of a typical coal mine or deep metal/nonmetal mine. Therefore, the ventilation techniques and principles are quite different. In addition, because of new MSHA regulations that limit the concentration of diesel particulate matter, these mines may need to greatly increase their ventilation airflow. Therefore, large-opening mines need a fan that can move large air quantities and operate at low static pressures. There are three fan types for mine ventilation: centrifugal, axial vane, and propeller. Centrifugal fans are uncommon in underground stone mines as they are often associated with mines requiring the highest of ventilation pressures. Axial vane fans are widely used in all types of mining operations. They are the most common fan type currently found in underground large-opening stone mines. However, they typically do not operate at low static pressures with high efficiency. Propeller fans are currently uncommon in underground stone mines. They are designed for low static pressures and large air quantities at higher efficiency. This fan type best suits the ventilation needs in large-opening stone mines?they produce large air quantities at low pressure losses. Mines with air shafts<100 ft long and at least 12 ft in diameter have fairly low mine static pressures and may also benefit from propeller fans.

Dec 1, 2002

By Gerald H. Groenewold

Reclamation of surface-mined landscapes is commonly defined only in terms of biological productivity. Other critical concerns associated with surface mining include the long-term quality of groundwater and stability of the postmining landscape. Meaningful reclamation design must address all these concerns. Reconnaissance of postmining landscapes indicates that three types of instability occur in these settings. These include: area-wide settling, localized collapse, and piping. Area-wide settling is most pronounced during the first year after contouring but appears in precontouring valley areas where frozen materials are contoured with a dozer. Although severe in some settings, development typically ends within one year. Piping appears to be a severe and long-term problem in some settings. Piping usually begins soon after contouring ceases and may continue for several years. In some postmining landscapes, piping has only started to develop after as many as five years of apparent stability. Piping is controlled by a combination of physical and chemical conditions in the spoil. A key factor is the presence of highly dispersive materials in the near surface. The design of a stable postmining landscape requires the integration of severe critical factors. These include: 1) detailed knowledge of the distribution of overburden materials with emphasis upon the delineation of highly sodic sediments; 2) proper equipment selection; and 3) a consideration of climatic factors. For reclamation to be successful, it must consider the entire landscape, not merely the soil zone. Any approach short of this will lead, at best, to temporary solutions.

Jan 1, 1980

By Elena L. Chanturiya, Vladimir A. Bocharov, Roman A. Amosov

"In many volcanogenic base metal deposits of Russia the gold is closely associated with copper sulphides and pyrite. The recovery of gold associated with pyrite is especially difficult problem.Investigations of gold chemical state and mineral forms in copper-zinc sulphide ores of Gay and Barsuchiy Log deposits in the Urals have been made using EPMA, optic image-analysis, XRA, SEM, thermo-electrical force measurements and selective gold leaching experiments.Two gold varieties are determined: 1) free native gold particles (from 5 µm up to 0,25-1,0 mm), which can be liberated after grinding of ore up to 0,074 µm and named “free gold”; 2)”invisible” gold, including finely disseminated native gold and chemically bound gold. The second variety can’t be disclosed during grinding. Free gold can be recovered by gravitation and flotation while the processing behaviour of “invisible” gold is determined by properties of gold-bearing sulphides: pyrite and chalcopyrite. According to results of diagnostic leaching experiments in ores of deposits mentioned above the part by weight of free gold reaches 70%, the part by weight of the ”invisible” gold is up to 20%. About 10% of gold is enclosed in quartz and acid-soluble minerals.Theoretically (taking into account gold distribution data) it’s may anticipate gold recovery by gravitation up to 60%. However after grinding up to 50-60% of class –0,074 mm only about 40% of gold passes into oversize product including 30% of free gold and 8% of ”invisible” one. It can be recovered by gravitation. Remaining free gold and ”invisible” gold can be extracted by flotation – 25% in total. Inevitable gold losses in tailings may reach 8-10%."

Jan 1, 2003

By H. J. Handewith

This paper explores the state-of-the-art of mechanical rock drilling and boring methods in use in the year 2000. It covers the basic mechanisms of cutting tool design and outlines the current understanding of related rock fracture methods. It provides suggestions for future research needs and discusses the mining and construction markets that are driving these needs.

Jan 1, 2001

By Sarma S. Kanchibotla

In overburden cast blasting the explosive energy is used to move a significant percentage of overburden from the high wall to the spoil pile thus reducing the amount of material to be handled by machinery. However, the obvious trade-off between the extra explosive energy in the cast blast versus reduced dragline effort is complicated by an increased risk of damage to the underlying coal. This damage may not be obvious but inevitably leads to reduced coal recovery and may negate much of the benefit sought from cast blasting.

Jan 1, 1999

By Mohammed Sakr

The use of helical piles for permanent foundation applications has become a practical and feasible alternative to the traditional cast-in-place concrete or driven steel piles. Research and development, installation equipment and manufacturing improvements in the helical piling industry have led to this trend. Moreover helical piles are typically smaller in size and weigh less than traditional piles, and require relatively smaller equipment and therefore it is a cost effective option. The latter is a very attractive feature for foundations installed in remote sites across Alaska. This paper presents full-scale pile load test results of helical piles and driven steel pipe piles installed in a site located in Anchorage, Alaska. Four full-scale pile load tests were carried out including two axial compression and two uplift load tests. Both helical piles and driven steel pipe piles were installed and tested at the same site under similar conditions to provide a direct comparison. The results of the full-scale load tests indicate the superior performance of helical piles compared to driven steel pipe piles. This paper describes the pile installation and test setup, presents the test data, and discusses the results.

Jan 1, 2009

By Unknown

More than 60 years ago Lakota (Sioux) Chief Henry Standing Bear asked Korczak Ziolkowski to create a monument of Crazy Horse in the sacred Black Hills. Today, you can see Standing Bear’s dream has grown into enormous reality. Crazy Horse Memorial, mankind’s largest mountain carving in progress, is being carved in the round and when completed will be 641 feet long and 563 feet high. Crazy Horse is only 17 miles from Mount Rushmore National Memorial, giving South Dakota unique boasting rights for having two extraordinary mountain carvings in such close proximity

Jan 1, 2009

By John D. Bardill

Data from extensive tests was obtained on friction-head losses of various sand slurries, composed of materials of different specific gravities and under varying transport conditions, to provide useful information for designing hydraulic transport systems. The tests were run in a pilot plant through 2-, 3-, and 4-inch lines with slurries composed of relatively pure barite and limestone solids. Available grinding and classification equipment did not permit attaining a comparable size distribution in the two materials tested, thus preventing direct correlation of friction-head loss values to physical properties or mineral composition. A total of 495 measurements were made of limestone slurries in the 2-, 3-, and 4-inch pipe test sections at flow velocities from 6 to 14 feet per second and pulp densities from 40 to 70 percent solids. A total of 640 measurements of barite slurries were made in the 3-and 4-inch pipe test sections at flow velocities between 7 and 14 f.p.s. and pulp densities ranging from 40 to 80 percent solids.

Jan 1, 1962

By N Rivera, A Music, C Cisternas

In an underground mine operated with panel caving and subjected to high stresses, geotechnical events such as collapses or rock bursts are fairly recurrent. Both situations can involve risks for people, considerable production losses and increasing operational costs.This paper discusses an operational methodology for the recovery of the undercutting front carried out at El Teniente mine, which uses panel cave mining with post-undercutting, after the occurrence of severe damage due to a seismic cluster. The main objective of the recovery of the undercutting front is to prevent the spread of the collapse to the production level, risking the operational continuity. The methodology is the result of repairs that were carried out in the year 2014 at the North Reserves sector from El Teniente mine. Its characteristics are an undercutting front of almost 1000 m long, with the presence of relevant structures and faults, high stresses and high seismic activity.The practical implementation of the proposed methodology was successful since it prevented the spread of the damage, completely recovered the undercutting front and avoided production losses during the execution of the repairs. Also, considering the origin of the damage and the operations associated to the subsequent recovery of the undercutting front, in this paper we discuss the main control variables to be measured. These variables should allow any operator and short-term planner to take action in mines operated with conventional panel caving in a complex geotechnical environment.CITATION:Rivera, N, Music, A and Cisternas, C, 2016. Recovery of the undercutting front in a mine with conventional panel caving – case study at North Reserves sector, El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 713–722 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J. L. van Niekerk

The proposed Gautrain Rapid Rail Link (GRRL) will require approximately 15 km of double or twin high-speed rail track tunnels located for the greater part beneath the northern suburbs of Johannesburg, including Houghton, Rosebank and Sandton. During the Environmental Impact Assessment (EIA) it became clear that potential surface vibration above and in the vicinity of the tunnels was a matter of serious concern to the residents of the affected properties and that the impact required assessment. The general method proposed is based on a US Department of Transportation, 1998, publication in which abase vibration curve derived for typical high-speed passenger trains is adjusted for the topological, geological and other features to predict the surface vibration and the associated ground-borne noise. The predictions indicate that some isolated areas might be impacted but that the impact will likely be limited, and it is possible to mitigate the impact using suitable track construction methods and track support systems.

Jan 1, 2004

By Libby R. Ricafort, Victorio V. Pato, R. S. Pizarro

Introduction Atlas Consolidated Mining and Development Corp. (ACMDC) started gold production at its Masbate gold mine early in 1980. This involved an open-pit mine and a 3.5-k/d (3850-stpd) carbon-in-pulp processing facility (Pizzaro and Antonio, 1981). When this operation started, the mine began stockpiling sub-grade milling material averaging 1 g/t (0.029 oz per st) gold. Furthermore, geologists estimated that there were additional low grade reserves within the ultimate pit limits. These amounted to 2.4 Mt (2.6 million st) with an average grade of 1.1 g/t (0.03 oz per st) gold. The success of low cost heap leaching prompted an investigation to determine if this tech¬nique would be applicable for the low grade Masbate ore. The findings were favorable and a series of laboratory tests were undertaken. These tests indicated the amenability of this subgrade milling ore to heap leaching. Depending on ore size, gold extractions of more than 60% were obtained. To further define operating parameters for a commercial heap leaching plant, a 400-t (440-st) batch pilot plant was built and operated. These test results were used to design the first commercial heap leaching plant in the Philippines. One design concern was the control of solutions during the rainy season. Due to the material&apos;s low grade, every effort was made to minimize capital and operating costs. To this end, surplus mining equipment from the copper operations of ACMDC and used machinery in the crushing circuit were considered. Location: The Masbate gold heap leaching operations are located on the northeastern part of Masbate Island, Philippines. This is about 480 km (300 miles) south-east of Manila. Climate: The climate is moderate with two distinct periods. The dry season runs from January through June, and the rainy season extends from July through December. During the wet season, the rainfall at the mine site averages 300 mm/m (11.8 in. per month) for a total of about 2000 mm/year (78 in. per year). However, heavy downpours in excess of 100 mm/h (4 in. per hour) can occur. Geology: Four distinct rock types have been identified in the pit area. They are tuffaceous agglomerates, andesitic agglomerates, metasedimentary rocks, and hornblende augite andesitic porphyry. The tuffaceous agglomerate occupies the northern and western flanks of the mine. Andesitic agglomerates are localized distinctly in the central portion of the volcanic plug within the mine site. The eastern boundary of the mine is occupied by metasedimentary rocks, whereas, the hornblende augite andesitic porphyry occurs as an intrusive within the andesitic agglomerate and tuffaceous agglomerate. Some areas of the pit contain high proportions of clay minerals, requiring an agglomeration step in the flowsheet. This ensures satisfactory percolation through the heaps. Ore characteristics: Gold and silver are microscopically dis-

Jan 9, 1987

By A. T. Jakubick, A. MacG. Robertson

This paper reviews key issues related to the placement of dry (soil) covers on extremely weak, compressible fine tailings. The design and construction of soil covers on such tailings often presents a formidable challenge to the geotechnical as well as the environmental engineer due to the low shear strength, poor traffic ability, and high settlement of under consolidated tailings at the time of reclamation. The geotechnical issues to be considered include: (1) consolidation of near-surface tailings to achieve strength gains, improve traffic ability, and allow safe placement of initial cover layer; (2) stability of tailings slopes during dewatering of tailings ponds and/or cover placement; and (3) long-term settlement of tailings and its impact on cover integrity and final surface shaping. The environmental issues to be considered include: (1) management of contaminated (free) pond water; (2) management of contaminated pore water expelled during tailings consolidation; and (3) management of (uncontaminated) surface water on top of the cover. This paper summarizes recent experiences gained in a large uranium tailings reclamation project. It is concluded that a careful consideration of both geotechnical and environmental issues during the planning stages greatly reduces the costs and environmental risks associated with fine tailings reclamation.

Jan 1, 2000

By A. Boniface

The International Tunnel and Underground Space Association (ITA) has a number of working groups (WG) that meet at least once a year. One of these is WG12, ?Use of Shotcrete?, of which the author is a member. The purpose of this paper is to draw attention to a number of topics that were discussed at the WG12 meetings held in April and September 2008; and also to a number of other matters that arose from the presentation of thirty-four papers at the 5th International Symposium on Sprayed Concrete held in Lillehammer, Norway between 21 and 24 April 2008.

Jan 1, 2008

By D. A. Norrgran, J. A. Wernham, D. E. Walsh

A qualitative test program was sponsored jointly by the University of Alaska and Eriez Magnetics, in order to study placer gold nugget recovery using an eddy-current separator. Various gold nuggets from Alaska, ranging from 6.4 mm to 63.5 mm in size, were tested. All testing was performed using an Eriez Laboratory ESC, Model REA, fitted with 2000 gauss, surface field strength magnetic rotor. The belt speed was set to 91 meters per minute and the rotor speed was set to 2500 rpm in the forward direction. The splitter was adjusted to just reject the largest pieces of rock that measured an average 76 mm x102 mm x 127 mm. Based on the results of this limited test work, it can be recommended to placer gold mine operators, that Eriez Magnetics ECS technology is a viable and practical concentration technology for coarse gold recovery. Silver and platinum were also tested.

Jan 1, 2003

By Hakan Gurgenli

Many coal seams have weak shale immediate roofs that cause ground control problems. Therefore, it is important to know the properties of these shales so that preventive measures can be developed in advance. However, it is sometimes hard to understand this rock type due to its unpredictable behavior. A good example of this situation is found in two shale coal mine roofs located in the Illinois coal basin (Herrin No. 6 seam). Although, these mines are located very close to each other, one of them has many roof falls, whereas the other has no measurable ground control problems. The aim of this paper is to explain why and how one shale roof behaves worse than the other. Laboratory tests, including point load strength index, slake durability index, moisture activity index, weatherability index, water content determination, swelling strain and x-ray diffraction tests were performed to analyze the shale properties. According to these analyses, some useful correlations were found between the engineering properties, moisture-sensitivity indices, and weathering properties. Finally, mine and support design considerations based on the test results were discussed and recommendations to prevent ground control problems were given.

Jan 1, 2006

By R F. Hoeberling

"The use of ground penetrating radar (GPR) for geological purposes has been underway for almost two decades. The commercial need for a versatile GPR that can rapidly identify buried objects andunderground voids has been recognized and is an area of research that has already proved useful for several geological activities. Several types of GPR endeavors have been reported in the literature, including exploration of placer deposits (Davis, et al. 1985) and heavy metals (Hammond and Sprenke, 1991), improving oil recovery (Witterholt and Kretzschmar, 1984), investigating coal seams (Coon, et al., 1981), stratigraphic survey (Fisher, et al. 1992), Lunar soils characterization (Olhoeft, et al. 1975 and Strangway, et al. 1977), characterization of rock around mine tunnels (Cook, 1985), location of old mine workings (Scaife, et al., 1992), location of abandoned gas wells in coal seams (Kemerait, 1992) and survey of hazardous waste burial areas (Horton, et al., 1981). Coal seammapping has been developed using a related continuous wave, phase discrimination technique (Stolarczyk, 1990). As the technology for the radar equipment and the onsite computational power has increased, many new applications have become feasible. This article will describe the present status of the GPR technology and indicate some of the exciting possibilities for nearterm prototypes now being constructed."

Jan 1, 1994