Search Documents

By Fabian Kirsch

Cyclic behaviour of axially loaded piles has been an issue since studies revealed that the capability to transfer skin friction into the ground is highly depending on the level and the number of load cycles the pile is subjected. It has been shown that degradation of skin friction due to axial cyclic loading leads to accumulating displacements and a severe reduction in pile capacity. In Germany the DIN 1054 as well as the Recommendations of the Working Group 2.1 ?Piles? of the German Geotechnical Society (EA-Pfähle) require the consideration of cyclic loading for the assessment of both the displacements and the capacity. Up to now no broadly accepted design method exists, which enables the engineer to give a reliable judgement on the pile capacity under axial cyclic loading and the displacements respectively. Instead numerous design charts make it possible to distinguish between stable and instable loading levels in order to ensure a design on the safe side. A newly developed design approach based on engineering models is presented which delivers a calculation algorithm for the remaining axial pile capacity after a defined number of load cycles to allow for the analysis of stability of the foundation. Furthermore the computation of accumulating displacements is made possible. The results are verified with pile load tests undertaken at Dunkirk, France and showed that the axial capacity after cyclic loading calculated with the newly developed design approach predicts actual capacity with an accuracy of ±20%.

Jan 1, 2011

horizontal-type classifier prior to charging into a blastfurnace.

Apr 1, 1995

By I. Loomis, D. Rachmad, I. Duckworth

During the past two years the Underground Mine Ventilation Group at PT Freeport Indonesia has undertaken to upgrade their Hygiene Laboratory. This process has included upgrading equipment for dust sampling and gas monitoring, as well as procurement of an OCEC analyzer for Diesel Particulate Matter analysis. While the laboratory equipment represents one factor, these changes have also required re-evaluation of the sampling protocols and the burden of ventilation monitoring personnel. This paper provides a review of these experiences.

Jan 1, 2006

By J. Persson, N. G. Bliss

Electric furnaces used for smelting and those used for scrap melting exhibit different performance profiles in terms of electrical characteristics. However, the underlying principles are the same for either case. The rationalization of these variables is a major concern for furnace operators and designers. This paper presents the results of a two year study of high speed real time data from a number of electric furnaces around the world, covering a very wide range of design philosophy and product manufacture, to provide a better mathematical insight into rationalizing the furnace operation.

Jan 1, 2004

Laboratory experiments show that the delay detonators, either electric (copper coated or aluminium) or non-electric (down-the-hole) as generally used in opencast mines and quarries have some scattering from the actual firing time due to manufacturing inaccuracy and variations in basic ingredients of the product. This scattering varies from 1 to 4 % depending on the product quality. Due to this component scatter, adverse blasting effects like misfires, overbreak, underbreak or fly-rock may occur if the design patterns are not judiciously made. It has also direct impact on muck profile and fragmentation.

Jan 1, 1999

By J. P. Brady

A major spontaneous combustion incident occurred in the sealed goaf of the SL3 Panel; Southland Colliery in 2003 resulting in the loss of a longwall and sealing of the mine. The most important issue for the new owners, Yancoal Australia Pty. Ltd, was to effectively manage the atmosphere in the fire affected sealed area. This atmosphere comprised of flammable gases, the products of combustion and excessive levels of oxygen due to pressure differentials across the panel isolation seals with a potential ignition source associated with the residual spontaneous combustion event. The challenges were met in the first instance by the erection of pressure balance chambers with limited success. The problem was not solved until the pressure chambers were pressurized using a Floxal Nitrogen Plant supplied by Air Liquide Australia. Given the success of this approach on a small scale, a higher capacity Air Liquide Floxal Unit was acquired to manage spontaneous combustion at the recommencement of longwall mining operations. This provided the ability to pressurize pressure chambers that were installed in the Maingate Seals behind the face of the adjacent Longwall Block effectively preventing the ingress of oxygen and permitting the goaf to self inert in a reasonable time period. This paper summarizes a new proactive method of mitigating the risks associated with active and sealed goaves. Proactive management of these areas using low flow nitrogen into pressure chambers to maintain a positive pressure has eliminated typical reliance in explosion proof or explosion resistance seals as the primary control.

Jan 1, 2009

By A. J. Davidson

A Cu-conducting solid electrolyte was used to develop the sensor. Instead of measuring the potential across the electrolyte from the reference material to the Cu-containing phase, a potential was applied and the stable current measured. This gave reasonable readings for copper-tin alloys, which agreed with the theoretical calculations, but was less satisfactory in the case of mattes because the surface area of electrolyte presented to the matte phase varied from sensor to sensor. To overcome this problem the potential was applied, the current was measured and then reversed and remeasured and the ratio of the currents was calculated. The current ratio is shown to be independent of the resistance of the electrolyte and the surface area of the electrolyte offered to the melt, but strongly dependent on the activity of the copper

Jun 21, 1905

By A. Habibi

A study has been undertaken on two 1.12 m diameter industrial booster fans operating under different blade settings powered by a 1200 rpm motor at the Missouri University of Science and Technology. The fans total pressure varies up to 1kPa forcingup to 25 m3/s through the workings. A pressure-quantity survey has been conducted inby and outby the booster fans with different blade settings. The study uses a variable speed drive (VFD) to determine the effect of rotational frequency on the system. The pressure drop across the bulkheads has been monitored during the experiments. The fans were operated with various blade settings to determine the optimal scenario that maintains the maximum airflow quantity and the lowest power demand at a particular ventilation station. Five scenarios were conducted with different blade setting and mostly with two different speeds. The experimental results show that alteration of fans? speeds by use of a VFD unit can reduce power consumption while maintaining airflow requirements. With the flow rate forced through the mine by the surface fan the blade settings 4 and 5 were determined as possible alternative for the mine ventilation system. In scenario 4, the airflow at the particular ventilation station for a number of speeds is over 20m3/s. The power consumption at 1080 rpm was measured to be 20.1 kW compared to 25.5 kW at 1200 rpm. The operating cost would be significantly less at lower speeds. Scenario 5 is the alternative making use of both booster fans and the main fan in series that meets the minimum airflow requirement at the particular ventilation station along with minimum power consumption. Reducing both booster fans speeds to 1054 rpm results in power consumption of both together dropping to 11.8 kW. Therefore blade setting 5 using two booster fans was determined to be the optimal setting. Separately it was determined that the combination with use of only one booster fan, the West booster fan, running in series with the main fan is the overall optimal scenario. The power consumption of the West booster fan was calculated to be 8.8 kW at 860 rpm with the minimum airflow requirement being met. Computational fluid dynamics is used for analyzing three dimensional flow structures in time domain and calculating the corresponding unsteady pressure fluctuations. The sliding and dynamic mesh techniques were used to study the unsteady flow interaction arising due to the rotation of the fan blades. The numerical predictions of the variables in the form of velocity vectors and contour plots detailing the flow characteristics are then analyzed according to the known physical situation and existing experimental data.

Feb 27, 2013

"Lax, misguided, and dangerous" is Rep. James Santini's description of the official US position on strategic nonfuel minerals. Santini (D-NV), chairman of the House Mines and Mining Subcommittee, criticized the Interior Department for "its long record of benign neglect" regarding the domestic minerals crisis. Santini made his remarks at a news conference at the American Mining Congress convention in San Francisco, where he released his subcommittee report "US Minerals Vulnerability: National Policy Implications." The report-said to be the first major congressional study of the minerals issue by a committee of jurisdiction is the result of a two-year inquiry. The investigation was undertaken, according to the chairman, "because no person or agency in the executive branch of government fully grasps the critical importance of nonfuel minerals to the nation's economy, defense, and quality of life." The report also urges a larger role for the Department of Defense, which has "stood passively by for many years as a consuming by-stander," according to the report. President Carter's incomplete Non-fuel Minerals Policy Review also drew the committee's ire; Santini calls it "a tragic waste that cost tax-payers $3.5 million and the loss of some 13,000 person-days." The subcommittee examined the following issues for its report: • The US minerals industry's inability to meet national raw material needs under a "hodgepodge of contradictory, restrictive, and irrational" federal regulations; • Dependency on foreign sources of strategic minerals in times of "increasing resource nationalism" and "Soviet mineral expansionism;" • National security needs for foreign mineral resources that do not have effective substitutes; • The US government's approach to national minerals policy "amid a growing realization that such a policy does not exist." The subcommittee report includes an analysis of public and private studies on nonfuel minerals and discusses a series of policy problem areas that negatively affect domestic production. Capital formation disincentives, tax policies, antitrust enforcement, environmental laws, health and safety regulations, technical problems, and restricted access to federally-controlled public lands contribute to what Santini calls a "tragic irony." "The irony is that we are a nation vastly rich in mineral resources yet our own government chooses to stifle development of these critical raw materials and thereby increase offshore reliance. The tragedy is that we also are ensuring US vulnerability to severe economic dislocations and a weakening of our national security." In just six years, from 1973-1978, the US trade deficit in nonfuel minerals rose from $2 billion per year to $8 billion, according to the report. The country imports more than 50% of 23 critical minerals, including 100% of its manganese, chromium, cobalt and platinum. The US is promoting its dependence on foreign mineral sources at the very time the security of many of those sources is becoming less certain, the report notes. Santini said the subcommittee investigation revealed a vulnerability that may be more serious and pervasive than that of foreign oil. The US may be able to develop alternate energy resources, but there are no effective substitutes for many nonfuel minerals. The report also discloses that US stockpiles of critical and strategic minerals are of inadequate supply and quality. Holdings of some vital minerals are far below present objectives, and for some there are no holdings at all, according to Santini. To resolve the current crisis, the report makes the following recommendations: • Complete immediately President Carter's Interagency Nonfuel Minerals Policy Review; • Implement (throught the Interior Department) the 1970 Mining and Minerals Policy Act; • Create an Office of Energy and Minerals with the same stature, power, and oversight responsibilities as the Council on Environmental Quality; • Ease federal restrictions on mineral exploration and development on public lands and implement a complete review of public land use policies; •Fund for and fulfill US nonfuel minerals stockpiling objectives; •Increase federal funding for non-

Jan 11, 1980

By A. Fredriksson, R. Christiansson, I. Staub

A theoretical model based on DFN models and 2D DEM numerical modelling has been developed for evaluating the rock mass mechanical properties. The description of the methodology is non-site related and can be applied in any site for this type of characterisation. The methodology was developed in the frame of the Site Investigation programmes for a Deep Repository for spent fuel in Sweden, and validated on sets of data coming from the Äspö Hard Rock Laboratory. Un modèle théorique base sur des modèles probabilistiques de réseaux de fractures et sur un modèle numérique DEM 2D a été développé dans le but de déterminer les propriétés mécaniques de la masse rocheuse. La méthodologie développée peut être appliquée à tout type de site pour ce genre de caractérisation. Le modèle a été élaboré dans le cadre des programmes de recherche d’un site d’enfouissement des déchets nucléaires en Suède, et validé par une application au laboratoire de recherche souterrain à Äspö. Ausgehend von DFN-Modellen und 2D DEM numerischen Modellierungen wurde ein theoretisches Modell für die Auswertung von mechanischen Eigenschaften von Fels entwickelt. Die Methodikbeschreibung ist nicht standortspecifisch sondern kan überall für diesen Typ von Standordkarakteriserung angewendet werden. Die Methodik wurde in Schweden im Rahmen der Standortuntersuchungsprogramme für die Endlagerung von verbrauchten Brennelementen entwickelt und ist mit Hilfe von Daten des Äspö Hard Rock Laboratory validiert worden

Jan 1, 2003

By L. M. Anisdahl

Ventiflex is a flexible ventilation duct system with a global market within mine and tunnel ventilation. The system is distributed in a wide range of qualities and dimensions. It is very important that ventilation systems are designed correctly in mines and tunnels. An incorrectly dimensioned system might result in bad air quality and too high costs. The objective of this study has been to assess some important design parameters for ventiflex comprising the friction loss factor for the duct wall itself, as well as the shock loss factors and the leakage factors for the different couplings systems. This has been obtained by carrying out a large scale experimental program on ducts with all the three different couplings: Velcro, zip and steel-ring. Pressure profiles and air flow rates have been measured, and based on these data the different factors have been calculated. The following results have been obtained: A friction factor l = 0,012 (K = 10) for the duct wall, a shock loss factor z = 0,0125 for velcro- and zip couplings, a shock loss factor z = 0,005 for steel-ring couplings, and a leakage factor f* = 0 mm2/m2 for all three coupling types. The latter result proves that no leakage is possible for a correctly installed duct with proper alignment. The results also confirm that ventiflex complies with class S, or better, according to the SIA-norm. However, whether ventiflex should be designed as class S, A or B according to the SIA-norm, depends on the particular application.

Jan 1, 2009

By S. Christiansen, G. R. Winslow, R. W. Kobler

Todays End of Life vehicles are shredded and their metal components recovered and recycled by standard methods. The remaining non-metallic fraction is shredder residue, and contains vast amounts of high value engineering plastics. None are today recovered. Discussed are the developmental approaches used in the first process to recover these valuable plastics. Examined are initial laboratory studies, pilot plant design and construction, product development, results, and flowchart explanations.

Jan 1, 2001

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By J. Patterson

"Acid Mine Drainage (A.M.D.) formed from oxidation of disposed pyritic wastes presents a potential pollution hazard for Equity Silver Mines Limited and the mining industry in general. Failure to collect and treat these acidic effluents can eventually affect the quality of receiving streams and endanger aquatic life forms. Treatment and discharge of A.M.D. to the receiving environment must comply with stringent anti-pollution laws.Wastes mined at Equity Silver Mines Ltd. are predominantly acid generating and must be handled according to a materials management plan to minimize impact on the environment. Effluent collection and treatment facilities have been constructed to address the short term environmental concerns with reclamation and research programs being developed to address and monitor abatement measures for control over the long term.The purpose of this paper will be to offer a brief overview of these measures. Key topics for discussion will be: kinetics of Acid Mine Drainage, acid generating potential, water treatment and sludge handling, special wastes, waste dump construction, waste rock amendments, bacteriocide research, simulations, and reclamation measures. Programs designed to evaluate impact on the receiving environment, although they form an extensive part of the program, will not be discussed in this paper.INTRODUCTIONEquity Silver Mines Limited is located in the Central Interior of British Columbia, within the Omineca Division, 35 kilometers southeast of Houston Mining and approximately 575 kilometers by air north-northeast ofVancouver (Figure 1).The deposit consists of three economic mineralized zones: The Southern Tail, Main and Waterline Zones. Mining of the Southern Tail commenced in April, 1980 and was completed in the first quarter of 1984. Main Zone production was initiated during the last quarter of 1983 and the Waterline Zone remains undeveloped to-date. Remaining reserves are in the order of four years contingent on favourable metal prices. The three deposits (Figure 2) occur within a window of interbedded volcanic and minor sedimentary rocks. The older volcanic sequence is bounded on the west by a small granite-like stock and on the east by a gabbro-monzonite complex. All are overlain by a series of younger lava flows."

Jan 1, 1988

By R H. Sillitoe

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Geological concepts are employed routinely in porphyry copper exploration at the area selection, prospect appraisal and deposit definition stages. Regional, district-scale, deposit-scale and laboratory-based concepts can all play a role, with the resulting porphyry copper models providing templates for the integration of geochemical and geophysical responses and interpretations. Of the 19 concepts and parameters selected for brief discussion, those relating to subdivision of porphyry intrusions, understanding of diverse and commonly complex alteration-mineralisation patterns and lithocap characterisation are undoubtedly the most influential in exploration. Several of them are of particular importance because of their role in promoting grade development. Additional belt-, district- and deposit-scale features are currently little used but hold promise, whereas others have less practical value but help in underpinning the evolving porphyry copper genetic model.CITATION:Sillitoe, R H, 2015. Recent advances in porphyry copper geology and their exploration utility , in Proceedings PACRIM 2015 Congress, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S. Hardcastle

Various controlled and ambient tests were undertaken to evaluate the performance of a variety of digital heat stress monitors, psychrometers and simpler temperature/relative humidity data loggers that measure, or determine, such parameters as: dry-bulb, natural wet-bulb, psychrometric wet-bulb and globe temperatures. In this comparison, funded by the Deep Mining Research Consortium, it has been found that all the instruments can competently measure dry-bulb temperature but the accuracy of other sensors could introduce significant uncertainty. For example the quality of relative humidity sensors and failure to correct for the barometric pressure difference in deep mines, directly impacts upon the calculation of psychrometric wet-bulb. The comparison has shown that the response of dry-bulb and globe temperature sensors can vary widely under different radiant heat conditions; however this would be negligible in most mines. Of more concern is the differing performance of the natural-wet bulb sensors especially at low relative humidity and low air velocity. Furthermore, from these tests and the currently available theory it was not possible to determine if any of the natural-wet bulb instruments measured that value correctly or validate any relationship between psychrometric and natural wet-bulb temperature at low air speeds where their difference is greatest. Consequently the uninformed use of some of the commercially available environmental heat stress monitors or derivations from other instruments could provide erroneous results affecting the work load category that can be accommodated or the rest ratio regime required.

Jan 1, 2009

A model was developed of a CIL/CIP circuit for recovery of gold and silver. The model uses a simple two rate representation of the leaching kinetics. Parameters for the leaching kinetics may be simply obtained by sampling the feed to a circuit and the tailings from each tank and assaying the solids for both gold and silver to obtain the assay profiles of the solids down the tanks. The parameters in such a leaching model would be expected to be a function of the ore type, the grind, whether oxygen was used and the general chemical environment. These parameters are primary inputs to the model for any simulation. Standard power law relationships are used to express the practical equilibrium between the gold and silver cyanides adsorbed on the active carbon and the tenor of the solutions. The parameters for this may be derived from solution and carbon assays for the same set of samples. The model is constructed by writing a mass balance for gold and silver in and out of each tank in the train and for the circuit overall. Other inputs to a simulation are the feed rate of ore, per cent solids of the slurry in the tanks, gold and silver loadings of the input æbarrenÆ carbon and the rate of movement of carbon through the circuit counter-current to the slurry. With appropriate practical parameters the simulation is able to reproduce typical tank profiles.

Jan 1, 2004

By Clive Chadbourne

Investigations of world wide coal face strata control practice, the study of theoretical calculations and detailed engineering analysis have been combined to design and select a powered roof support suitable for use in conjunction with the extraction of 4.5-m (14.7- ft) of the 7.5-m (24.6-ft) thick Warwickshire Thick Coal Seam. The interface between geotechnical criteria and engineering design has been closely considered along with the following 3 important factors: Firstly, the need to further improve strata control and operational characteristics whilst producing a wall integrated overall face design. Secondly, to enable the supports to be rapidly transported from face to face in roadways driven at the minimum size for operational requirements. Finally, to provide hydraulic power, automatic control and monitoring systems which will improve operations reduce manpower requirements and improve management information. Clear design requirements were determined in order to allow selection on a commercial basis. A method of tendering is described with the subsequent analysis and selection process. In the event oversupply of coal in the UK resulted in the order not being placed. Brief consideration has been given to supports suitable for reserves to be mined In a few year's time where there is potential for extraction well in excess of 4.5-m (1 4.74.

Jan 1, 1994

By Erik Westman

Coal bumps remain one of the industry?s most devastating but least understood phenomena. If changes to the internal conditions of the rock mass could be observed there is hope that bumps could be forecasted. Seismic tomography has been used over the past 25 years in an attempt to image these changing conditions in the vicinity of the longwall face. This paper describes the history and practical considerations of using seismic tomography in bump-prone coal mines. The implementation of seismic tomography at six different longwall mines will be described along with lessons learned. Early studies used mining independent sources of seismic energy, including explosives and sledgehammers. Subsequently more operator friendly sources, such as the mining equipment itself and mining-induced seismicity, were used. Seismic energy sensors have been placed in gateroads and on the surface above the mine. Each of these configurations has associated advantages and disadvantages. Although the results obtained have been encouraging, the application of seismic tomography to monitoring a bump-prone longwall face is still immature. The ultimate goal of clearly imaging changing stress conditions in the longwall panel in a manner that does not inhibit mining operation is still distant, yet drawing nearer. When this goal is achieved, the industry will have a capable tool for identifying locations where bumps are imminent.

Jan 1, 2008

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. Phases of the Ir sub-group are present either as inclusions in or interstitially to chromite and are unaffected by (or only altered in situ during) hydrothermal processes. By contrast, almost all phases of the Pd sub-group are located in a secondary textural setting - in fractures in chromite or between fragments of brecciated chromite. The different settings indicate that the mineralisation episodes were associated with magmatic and hydrothermal stages respectively. The presence of an included Pd-group mineral in a hydrothermally Pd-group mineralised chromitite sample suggests that the hydrothermal Pd-group minerals were at least partly derived by remobilisation from magmatic deposits in the chromitite pod. These observations indicate that Pd-group elements are more mobile than Ir-group elements under hydrothermal conditions and point to the potential for hydrothermal platinum and palladium mineralisation in favourable environments

Apr 1, 1994