Search Documents

By J. Cygankiewicz

Efficient prevention of mine fires is impossible without predicting the self heating processes in the given geological and mining conditions. The respective forecasting method is presented in this paper based on the following assumptions: - factor deciding on fire hazard in the underground workings is the process of heating of coal from the primary rock temperature to the critical temperature when the heating rate growth rapidly - another important factor is the fire incubation time defined as time needed to achieve the critical temperature. This time is determined by balance of heat and mass in the heated coal - contact of crushed coal with oxygen in air cause some exothermic processes as : physical and chemical sorption of oxygen , oxidation reaction and evaporation of humidity Heated coal transfers its thermal energy to the environment by conductivity to the rocks and by convection to the flowing gases. The heating is possible if thermal energy generated from coal is greater then the share transferred to the environment. The paper presents the laboratory method of measurement of heat generation in adiabatic conditions. Also the mathematical model with examples of computation enabling to forecast the self heating process of crushed coal is presented.

Jan 1, 2003

Reliable estimation of in situ stress is a major step in the analysis and design of underground excavations in rock, particularly for evaluating the stability of underground structures to prevent failure or collapse. In the last ten years, the Western Australian School of Mines (WASM) has studied and developed an AE stress measurement technique using orientated core named the WASM AE method. It allows the determination of a representative and detailed knowledge of the in situ stress field during the early stages of a project (such as mine feasibility studies), even in areas where development access is not yet available. The method has been used for in situ stress measurement at more than 80 mine sites worldwide with over 200 individual stress measurements carried out to date. This paper describes the sample collection, sample testing and reconciliation of results for very deep measurements carried out at the Craig-Onaping mine complex in Sudbury Canada. The results constitute the deepest measurements undertaken to date at the WA School of Mines and indicate that the main principal stress is horizontal and oriented parallel to a common regional sub trend in a NE/SW direction.

May 1, 2009

Tailings embankments can develop a high phreatic surface if the original design for the embankment does not include drainage facilities or if existing drainage facilities become ineffective. Subsequent raises can develop a seepage surface due to a high phreatic surface that can lead to stability problems. The U. S. Bureau of Mines amended contract J0100013 to initiate this study of horizontal drains in tailings embankments. This study developed a technique for determining the length of and spacing between parallel drains through the use of the finite element model UNSAT2. The analysis is based on the combined output of a vertical planar mesh and a horizontal planar mesh. The slot opening in the drain pipe and the length of the perforated section are determined from an analogy to water well design. The pipe diameter and gradient can be determined from Manning's equation. To the authors' knowledge, this is the first attempt at horizontal drain design using a finite element model. Additional research is recommended in this area.

Jan 1, 1982

By H. Krogerus, P. Jokinen, T. Lintumaa

The energy consumption and recovery of chromium are important economic factors in ferrochrome production. Outokumpu has a lot of experience of the reduction behavior of the sintered pellets in industrial-scale furnaces and also on the grounds of numerous laboratory and pilot-scale investigations. Sintered pellets have shown a superiority over lumpy ore and briquettes made of the same chromite grade. The good performance of the pellets has also resulted in investigations on the reasons for such a performance. In this study, the factors affecting pellet behavior in smelting furnace were investigated. This study is divided into two sections, i.e. the investigations were on the factors affecting solid state reduction and on the factors affecting reduction under melting. These tests were performed by means of thermo gravimetry and by smelting tests. The correlation between the pellet characteristics and reduction behavior was shown and its influence on industrial-scale furnaces was discussed. Factors worth of consideration are for instance, the extent of oxidation during sintering, slag formation and chemistry in respect of molten state reduction, and the grain size of the chromite mineral in the raw material in respect of kinetic reasons (retention time in smelting).

Jan 1, 2007

By J. A. Finch, Zhenghe Xu

The competitive adsorption of xanthates on sulphide minerals in a binary mineral system (pentlandite and pyrrhotite) was studied using the pseudo-in-situ technique of attenuated total-reflectance FTIR spectroscopy. The minerals were placed in the same collector solutions, either separated by a glass wall or in direct contact with each other before magnetic separation and separate analysis. The effect of mineral interaction on xanthate adsorption was clearly demonstrated spectroscopically for the first time. At low concentrations of xanthate, its adsorption on pentlandite was activated by physical contact with pyrrhotite; the effect may be attributed to the enhancement of electron transfer through electrical contact between the two minerals. The results emphasise the need for caution in extrapolating results obtained from single-mineral studies to flotation practice

Jun 18, 1905

By Edward G. Cunney

[Track in underground bituminous coal mines was investigated and technology has taken from other industries in order to Main information on conditions that impair the safety and efficiency of the track and to develop guidelines ad useful information on the constriction, inspec¬tion and maintenance of mine track. Volume l contains information oil the investigations, observed track conditions, useful technology from railroads and other industries, derivations of track condition descriptors and limits, conclusions, and recommendations. Volume 2, Guidelines, contains recommended standards and practices for mine track. It includes the relation of track conditions to safe speeds; descriptions and limits for measurable track features such as gage, descriptions of conditions for track components that are normally not measurable, such as subbase soils; construction requirements and techniques; inspection requirements and methods; and methods for managing and performing track maintenance work. As a research product, it 0005 nut repeat the summary or derivations. Volume 5, Inspection Handbook, summarizes recommended standards and procedures from Volume 2 and provides related information for read: refer¬ence by inspectors in tin mines. As a research product to be used in mines, it does not repeat the summary, derivations or references.]

Jan 1, 1977

Mineral formations, accumulated during technogenic activities greatly influence an economic and ecological situation in the Kola North. On the one hand, the dumps from extraction of mineral resources, tailing ponds of beneficating plants, ash dumps, wastes of metallurgical and mechanical engineering productions destroy the regionÆs environment and require taking certain measures and costs to bury or protect from weathering, oxidation, etc. On the other hand, technogenic mineral formations contain a lot of valuable scarce components. The amount of solid wastes increases annually, causing damage to ecology and economy. Researches conducted in recent years showed a possibility and economic expediency of comprehensive processing of wastes from different enterprises in Murmansk region and their use for production of new competitive commodity output, possessing high consumer properties. Thus, involving mineral wastes from Khibiny apatite deposits into hydrometallurgical industrial processing provides the basis for setting up a large beneficating-metallurgical complex. In this case ores and wastes from other deposits on the Kola Peninsula, containing titanium, rare, rare-earth and other valuable elements, may be involved into processing. Establishing such a complex will allow to organise a deep processing of natural resources, utilise some production wastes, improve ecological security and supply production with competitive output. Expanding the complex implies not only involving new mineral raw material into processing, but mainly deepening raw material processing, maximum utilisation of local natural resources and obtaining a wider variety of prime products.

Jan 1, 2002

By Muhannad T. Suleiman

Temperatures below freezing significantly enhance the soil shear strength and stiffness and to a lesser extent increase the compressive strength of concrete as well as the yield and ultimate strength of reinforcing steel. Consequently, the lateral load resistance of bridge columns supported by drilled shafts becomes dependent on seasonal weather conditions. To investigate the effects of seasonal freezing on the behavior of bridge columns supported by drilled shafts, large-scale field lateral load tests were conducted at 23°C (73.4°F) and -10°C (14°F) on two identical units at an field test site, which consisted of glacial till soil classified as low plastic clay. The bridge column-drilled shaft systems were subjected to cyclic lateral load with the maximum lateral column top displacements reaching approximately ±30 cm (±11.8 in.). The soil at the test site was characterized at different temperatures using unconfined compression tests in the laboratory as well as in-situ Cone Penetration and Pressuremeter Tests. Using these test results, the lateral load behavior of the column-drilled shaft systems were analyzed utilizing numerical models that consisted of beam elements representing the concrete column and the shaft and lateral springs representing nonlinear p-y response of soil. This paper focuses on comparing the calculated responses of test units with different p-y curves that were developed for the soil near the ground surface using the laboratory and in-situ tests. From the experimental study, the response of the unit tested at -10°C (14°F) was found to show 44% increase in lateral force resistance and 0.84 m (2.76 ft) upward shift of the maximum moment location compared to the response of the identical unit tested at 23°C (73.4°F). Theoretical behavior that included the temperature effects on soil, concrete and steel properties provided good correlation with the measured responses when the soil near the ground surface was modeled using the unconfined compression test or the Cone Penetration Test data, but not the Pressuremeter test data.

Jan 1, 2006

By A. Kapito

The formation of bainite in steel is dependent on the size of the casting, the heat treatment, and the alloying elements. It is difficult to obtain a fully bainitic microstructure in steels during heat treatment because of its close proximity to the martensite (a?) reaction. The ferrite (a) and pearlite reactions in steels are also rapid and shield the bainite reaction. Alloying elements therefore need to be added to separate the bainite reaction. Boron (B) and molybdenum (Mo) are key elements added to bainitic steels because of their ability to retard the a reaction. Other elements used in the production of bainitic steels are silicon (Si), chromium (Cr), manganese (Mn), and titanium (Ti). In this paper we investigate the effect of alloying elements on the bainite reaction through the use of dilatometry. Dilatometry is a technique that determines phase transformations in the steel and through which continuous cooling transformation (CCT) curves can then be developed. Some initial results are presented of an ongoing study on the development of bainitic steels for railway wheel applications.

Jan 1, 2013

By Lee Nichols

Convergent Bitumen Recovery Context of discussion It should be noted that the CBR process is a conceptual bitumen recovery feed methodology, designed to provide supplemental bitumen to the oil sand operations of Northern Alberta. To date the following have beencompleted. ?Bench Scale testing. ?Peer group brainstorming. ?Energy Balance ?Confidentiality agreements have been signed with several companies Discussions are ongoing with industry and although conceptual atthis stage the process holds significant promise.

May 1, 2007

By S. Slottee

The technology of making and using ?paste? from mine tailings is increasingly well known by the minerals industry. The primary applications are water recovery and ?stacking? of tailings with minimal use of dams and ponds. This paper highlights some applications, other than water recovery and stacking, that have come to the attention of a paste thickener equipment supplier. As generated by thickeners, paste (also called ?thickened tailings?) is a non-settling, relatively high concentration, suspension of solids that can be pumped. Paste deposits with an angle of repose, allowing minimal use of dams. High solids concentration allows more water recovery at the paste thickener than is achieved in conventional and high rate slurry tailings thickeners. This paper is based on paste as produced in a flow sheet that includes a thickener, underflow pumps that are typically centrifugal, transfer pumps that can be centrifugal or positive displacement, and a distribution system at the deposition site. Examples of paste applications other than water recovery or stacking include: ?mine? an existing tailings pond by removing slurry, recovering coal or iron ore values, and return the new tailings to the pond as a paste that does not res-suspend; use paste to seal an existing tailings pond from leaking to groundwater or to an underground mine; extend the life of an existing tailings pond by thickening the tailings to paste; move an existing dry tailings impoundment to a new location by slurrying, pumping, paste thickening, and redeposit; minimize the size of a filter by paste thickening the feed; operate a paste thickener and filter in parallel on a tailings stream with re-mixing to achieve a high solids concentration. The use of paste tailings technology has been expanding over the last 15 years. The applications, both implemented and under consideration, are increasingly diverse and include all minerals tailings. Tailings handling designers should always consider a paste option to the conventional slurry solution.

Jan 1, 2011

The extraction and processing of minerals from surface mines and quarries can produce significant fugitive emissions as a result of site activities such as blasting, unpaved road haulage, loading, primary crushing and stockpiling. Uncontrolled fugitive dust emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. Simulation technology is finding increasing use for the purposes of advanced warning of potential problem emissions in addition to providing a basis for future planning applications where demonstrable compliance with regulatory requirements are necessary. The initial re-entrainment and subsequent dispersion of fugitive dust presents a process complicated by the combination of the in pit topography, the surrounding natural topography and the dynamic nature of emissions from these sites. These factors impact upon the accuracy and reliability of the conventional Gaussian plume based computational prediction methods employed for regulatory compliance and IPPC applications. This paper proposes that optimal modelling of open pit emissions may be more accurately achieved by the use of a multi-scale predictive modelling approach utilizing computational fluid dynamics (CFD) methods for high resolution near source dispersion and conventional Gaussian based methods for far field dispersion modeling. This paper presents a numerical based flow and dispersion analysis of a typical UK based open pit utilizing CFD in conjunction with a conventional Gaussian plume based methods. Typical operating emissions and meteorological conditions are obtained from long term data records collected at a large operating quarry extraction operation in the UK. Emissions are modelled using a Lagrangian framework within conventional atmospheric boundary layer (ABL) profiles expressed as functions of turbulence and velocity parameters under assumed neutral conditions. Results are presented in terms of the impact of site topography on in pit retention as compared to the Gaussian based method.

Jan 1, 2009

By R Lastra, J. A. Finch

An artificial standard material has been developed and used to examine the robustness of some of the procedures for correcting stereological bias. Different mineral liberation distributions were constructed from the standard material. The particles were mounted, sectioned and the sectioning data measured with an electron microscope interfaced to an image analyser. Four correction procedures were used and the corrected and true liberation distributions compared. It was found that the large-sections correction provided a simple, uncorrupted correction. Hill's fast approximation performed well except in cases of narrow liberation distributions; the sectioning data appeared to support the assumption that the locked section and locked particle distributions are identical. Barbery's correction performed well in most cases, having difficulty only with the very irregular liberation distribution. The PARGEN correction was able to provide a good estimate of the true amount of free material, but had difficulty in predicting the locked particle distribution

Jun 21, 1905

By J. Kerr

The first stage of the development of a new modified 201-type low nickel austenitic stainless steel is described in this paper. The alloy is intended for use as a structural alloy, and so requires a yield strength >400MPa as well as acceptable weldability and toughness. The low nickel content will give a lower material cost in comparison to more conventional austenitic grades, and the processing route is required to be similar to that of Type 304 to keep the processing cost low. The base alloy was designed using empirical methods developed for stainless steel, and the properties of the base alloy were verified using a range of small-scale melts. The base alloy had a 0.2% proof strength of ~320-400MPa, and so it is planned to use V additions of ~0.15% to bring about precipitation strengthening in the hot rolled condition, so raising the alloy?s proof strength above the 400MPa minimum.

Jan 1, 2004

By C. Y. Liu

This paper principally deals with the application of caisson foundation in the Chinese bridge building industry, the different types of caisson foundation adopted, and their spheres of application. Caisson foundation has been used and speedily developed for bridge works in New China, and a number of new innovations have been made in its design. Especially in deep water foundation, the Nanjing Bridge over Changjiang has attained one of the deepest bridge foundations in the world. There are six types of deep caisson foundation being now in use in China, namely:

Jan 1, 2010

By R. Mark, R. Richards

The Washington National Cathedral is one of the largest masonry structures in the USA, and like many of its European Gothic counterparts, it required nearly a century to construct. The design was altered during this period, resulting in greater loadings than were originally anticipated on the soil beneath the foundation. When signs of continuing differential settlement were observed in the early 1990's, the Cathedral approached the US Bureau of Mines (now the National Institute for Occupational Safety and Health (NIOSH)) for assistance in monitoring the movements of the massive towers and walls. An array of dual-axis tiltmeters was installed about 40m above ground level to measure wall and tower inclination, with the data sent over a dedicated phone line to the NIOSH Pittsburgh Research Laboratory for processing. Mechanical gages and string-potentiometers are also being used to measure motion across cracks and joints, and differential pier settlement is being monitored with optical-level surveying. Data have now been collected for almost 7 years, and they show a long-term settlement trend masked by dramatic diurnal and seasonal thermal movements. The paper discusses the major findings of the study, implications for the future of the Cathedral, and conclusions regarding the use of geotechnical monitoring at major national monuments.

By G. R. Lane

A large opencast gold mining company in Africa had just completed a feasibility study for an expansion of the operations. A traditional net present value project valuation methodology had been used that showed a very positive net present value (NPV). The project team had conducted a qualitative risk assessment that identified and logged all potential project risks and had subjectively incorporated 'risk' via the discount rate and other assumption contingencies around gold price expectations, operating parameters, etc. Management requested that an independent quantitative risk modelling approach be adopted to obtain a better understanding of the impact of risk on the overall project valuation and confidence level in the final valuation. A detailed project valuation model was configured in the Cyest Carbon Modelling Technology platform, and the stochastic modelling module used to perform the Monte Carlo simulations. Analysis of historical operational performance data relating to actual achievements versus planned and budget determined the historical variability of the underlying parameters as well as variance to budget. This was done at a detailed level for mining rates and costs, processing rate, costs and recovery, and other operational efficiency measures. External market assumptions relating to gold price, exchange rate, and inflation were modelled and the dependency between them modelled using a copula. This case study will demonstrate the approach taken to building and populating the quantitative risk model and the overall results of the Monte Carlo simulation. The final valuation demonstrated that the project had a 44 percent probability of an NPV less than zero i.e. a 44 percent chance of project finance loss.

Jan 1, 2013

By Gunnar Persson

The borehole pressure/time history of blasting practice is simulated in a twin pendulum apparatus, where the expanding shotfiring gases force two steel slab swingers apart. A pilot installation built at SveDeFo is described. The relevant factors, that govern the use of this test method as a means of classifying explosives with respect to their toxic fume potential, are described.

Jan 1, 1996

By William I. Busenbark, Elmer C. Newman

At Bingham Canyon, the world's largest open-pit copper mine, annual grease consumption is in the neighborhood of 109 000 kg (240,000 lb), all of which was 544 (120-16) purchased, warehoused, and distributed in 54-kg (120-1b) and 180-kg (400-1b) drums. While perhaps a menial and mundane chore, grease distribution shows on the ledger as a significant expense item. To improve labor and cost performance, Kennecott maintenance engineers undertook a study to find the most direct method for moving multi purpose grease (MPG) from the refinery to the point of final consumption. What they found was a direct vendor system for hulk grease so simple and flexible that long-established drum distribution is being phased out in favor of the newer method throughout 75% of the operation.

Jan 9, 1977

By George J. Conroy

Electrical power generation was studied in a laboratory-scale, open-cycle vortex MHD generator, which offers several advantages over straight-channel generators that require separate combustors. Compactness, lower capital cost, and high-energy release are obtained by combining the combustor and generator into one unit in the vortex generator. In addition, the vortex generator uses a simple solenoid rather than the more complex and expensive saddle magnet required for straight channel generators. Although the vortex generator must utilize combustion gases with a low Hall coefficient in order to be efficient in direct comparison to the linear generator, the primary motivation for this experimental device in terms of ultimate objective was to investigate the vortex generator with applications to direct coal firing and with combustion taking place in specially designed expansion nozzles. The vortex device offers one decided advantage over the linear device in this regard because slag deposits do not degrade or short-circuit the coaxial electrodes as is the case for a linear machine. The experimental vortex generator consists of a modified cyclone burner 7 ½ in ID by 21 in long, with the inner wall used as one electrode together with a coaxial center electrode. Power was obtained by impressing an axial field of 3,000 G from an air core solenoid magnet. Tests were conducted by seeding natural gas seeded with potassium acetate and burning with preheated oxygen-enriched air. Power generation was lower than calculated because theoretical plasma velocities were not achieved.

Jan 1, 1972