Search Documents

Jan 1, 1967

By B. Clermont

Ball mills are usually the largest consumers of energy within a mineral concentrator. Comminution is responsible for 50% of the total mineral processing cost. In today?s global markets, expanding mining groups are trying to optimize mill performances. Since comminution is concerned with liberating valuable minerals for recovery in the separation process, it is crucial to run the mills at the best operating conditions which lead to good liberation at competitive throughputs with minimum costs (energy and wear). The high availability of the equipment is also essential to maximize production and profit. To reach this key objective, continuous and reliable information about the mill operation is vital. An innovative tool which can deliver information about in-mill dynamics has been developed by Magotteaux. It can provide online and accurate measurements of the degree of grinding ball fill and pulp position for timely decision making and actions. This tool could be used on its own or linked to an automatic grinding ball loading system named Magoload. Therefore, ball load could be kept constant by using direct measurement. This article describes the Sensomag and presents some of the major improvements that can be achieved with it. Some other promising avenues are still to be explored. Keywords: Comminution, process control, process optimization, process instrumentation, online analysis.

Jan 1, 2010

By B. O. Odera

The Pt-based alloys have a high potential for replacing some Ni-based superalloys (NBSAs) used in the highest temperature and most aggressive environments, and vanadium would be a beneficial alloying element. Six alloys of average compositions Pt-26.6Al-9.1V, Pt-23.1Al-17.8V,Pt-9.6Al-21.1V, Pt-17.4Al-6.4V, Pt-22.3Al-7.9V, and Pt-6.0Al-10.1V (all in at.%) were manufactured by arc-melting and examined in the as-cast condition using scanning electron microscopy and X-ray diffraction (XRD). Five samples were heat treated at 1 000°C for 1 500 hours and water quenched, then examined. The phases were identified using energy-dispersive X-ray spectroscopy and the identities were confirmed by XRD. In most of the samples, the phases existing in the as-cast condition were different from those at 1 000°C after ~1500 hours heat treatment. A solidification projection, an isothermal section and a liquidus surface projection were determined for the Pt-rich corner.

Jan 1, 2012

In several of the States of Australia, mining on private property has been seriously hampered by the fact that large areas of land have been alienated from the Crown before the discovery of gold or other minerals. In Western Australia this difficultyhas only occurred to a small extent, and has largely been overcome by an act entituled "An Act to Permit Mining on Private Property, No. XXIX., 'October, 28th, 1898." Under this act, the holder of a miner's right can apply for a gold mining lease on private land; such applicant may treat privately with the owner of such land as to the amount of compensation to be paid for surface ,damage, or the case may be brought before the Warden who will assess the damages. Private land used as a garden, orchard, or vineyard is exempt from lease, unless the applicant has authority from the owner, or such lease is limited to a greater depth than 100 feet from the lowest part of the surface.No lease shall be granted of any mines under any private land in any municipality unless either the applicant has authority from the owner, or such lease is limited to a greater depth than two hundred feet from the lowest part of the surface.The same regulation applies to leases of private land on which any hospital, asylum, or public building is situated or under or within one hundred and fifty yards laterally of any...

Jan 1, 1901

By Steven R. Munts

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 39,420 acres of the 60,960-acre Skedaddle Wilderness Study Area in order to evaluate its identified mineral resources. There are no known mines or mining operations in the study area. None of the prospects or claims in or within a 1 mile peripheral zone around the study area have recorded production. At least 276 recorded lode, 6 unrecorded lode, and 29 placer claims have been located in and within about 1 mile of the study area. Approximately 191 of the claims are in the study area. Four of these were current in 1985; all four are wholly or partly inside the study area. None of the study area was being explored by private industry in 1985. Metallic and nonmetallic commodities present in the study area consist of gold, mercury, perlite, basalt, pozzolan, stone, and sand and gravel. Perlite is represented by a single deposit which contains 184,000 tons of subeconomic resources in and adjacent to the study area. No other sites contained identified resources. There are no other identified nonmetallic resources in the study area. Occurrences in and near the study area contain small amounts of gold and mercury in vein-type deposits and show characteristics similar to bulk-tonnage, low-grade gold deposits. No base-metal resources were identified. The gold and mercury mineralization and perlite deposit are spatially related to a volcanic center located in the Skedaddle Mountains. Prospects in the Skedaddle Mountains may contain both precious metals and perlite resources, but additional work is required to adequately delineate these areas.

Jan 1, 1987

By I. D. Schleicher, L. H. Rorden, F. B. Curry, T. C. Moore

The purpose of this program is to extend electromagnetic (EM) techniques for use in locating miners trapped in mines as deep as 1000 m. A previously developed EM system is considered adequate for use at mines less than 300 m deep where it has a probability of detection of 54%. A system for deep mines must keep underground equipment simple, and use extremely low frequencies (ELF), sensitive receivers, and noise cancellation. The proposed location method, developed by Develco for other applications, is based on vector field measurements from two or more static sensors and computation of source location by iterative techniques. During Phase II, very sensitive search coil sensors were built and used in a separate test to verify the feasibility of atmospheric noise cancellation. A "Breadboard" location system version without cancellation, which is a fieldable test bed to evaluate receiving and location functions, was tested and supplied. Very good results were achieved from the first in-mine test with the transmitter at a depth of 380 m. It is expected the results of this work, and additional evaluation tests in the future, will be used to define the requirements for a prototype operational system.

By N. R. Morrow, C. C. Harris

The experimental points which describe capillary pressure curves are determined at apparent equilibria which are observed after bydrodynamic flow has ceased. For most systems, the time required to obtain equalization of pressure throughout the discontinuous part of a phase is prohibitive. To permit experimental points to be described as equilibria, a model of capillary behavior is proposed where mass transfer is restricted to bulk fluid flow. Model capillary pressure curves follow if the path described by such points is independent of the rate at which the saturation was changed to attain a capillary pressure point. Aemodified suction potential technique is used to study cyclic relationships between capillary pressure and moisture content for a porous mass. The time taken to complete an experiment was greatly reduced by using small samples. INTRODUCTION Capillary retention of liquid by porous materials has been investigated in the fields of hydrology,l soil science,2 oil reservoir engineering,3 chemical engineering," soil mechanics,5 textiles: paper making: and building materials In studies of the immiscible displacement of one fluid by another within a porous bed, drainage columnsl and suction potential techniques2 have been used to obtain relationships between pressure deficiency and saturation (Fig. 1). Except where there is no hysteresis of contact angle and the solid is of simple geometry, such as a tube of uniform cross section, there is hysteresis in the relationship between capillary pressure and saturation.2 The relationship which has received most attention is displacement of fluid from an initially saturated bed (Fig. 1, Curve R2), the final condition being an irreducible minimum fluid saturation Swr. Imbibition (Fig. 1, Curve A), further desaturation (Fig. 1, Curve R), and intermediate scanning curves have been studied to a lesser but increasing extent.2 ,3,9-12 This paper first considers the nature of the experimental points tracing the capillary pressure curves with respect to the modes and rates of mass transfer which are operative during the course of measurement. There are clear indications that the experimental points which describe these curves are obtained at apparent equilibria which are observed when viscous fluid flow has ceased; and any further changes in the fluid distribution are the result of much slower mass transfer processes, such as diffusion. Unless stated otherwise, this discussion applies to a stable packing of equal, smooth, hydrophilic spheres supported by a suction plate5 with water as the wetting phase and air as the nonwetting phase. The discussion can also be applied, in many

Jan 1, 1966

By Robert Hopler

As a part of the depression and rectification work on the Port Morris branch of the Harlem Division of the New York Central & Hudson River Railroad, a short tunnel is being driven under St. Mary’s Park. The park is near 149th St. and St. Ann’s Ave., in the Borough of the Bronx, New York City.

Jan 1, 2006

By T. A. Kirk

"The Linatex Dewatering System is a compact, low capital and maintenance cost matched set of processing equipment suitable for solids recovery, dewatering and desliming sand-like materials in the range 3/8"" to 325 mesh ( 1). Since its introduction to North America in the early 1970s, various elements of the system have been successfully installed in a variety of applic11tions both in Canada and the U.S.A. Examples are chosen from the coal, fine aggregates, iron ore and industrial minerals industries.II. Elements of the Linatex Solids Recovery System(A) The Linatex Separator (See Fig.I)The Linatex Separator, which is the heart of the system, is a specialized type of hydrocyclone designed to give a self regulating rope discharge product. It has the familiar cyclone geometry of cylindrical and conical section, tangential inlet, apex and vortex finder. The apex is enclosed in a unique patented automatic underflow regulator consisting of a collapsible rubber sleeve, and the overflow line is a siphon-leg, with a controlled air bleed valve. The siphon leg is adjusted so as to balance the internal negative pressure acting as a closing force on the underflow regulator against the mass of slurry pressing down on it from the cone section of the Separator. With correct adjustment the underflow regulator will close drip-tight on a water only feed. As solids accumulate in the apex of the cone the weight of solids counterbalances the vacuum and cat1ses the underflow regulator to open and discharge classified material at a controlled density."

Jan 1, 1978

The centrifugal elevator invented and patented by the writer is designed for the purpose of conveying the tailings of a gold dredge to such a distance that it shall not impede the dredging opperations. Formerly this was usually accomplished by means of a belt of buckets travelling round a ladder set at an angle of about 30 degrees to the horizontal, but this meant heavy wear and tear on the travelling buckets and the tumblers actuating them. The centrifugal elevator throws the tailings through the air to the required height and distance and it is manifest that during their flight from the elevator to the heap there is absolutely no wear and tear, only the attraction of gravity and the resistance of the air has to be overcome. All then there is left to he considered is how to throw the stuff with the minimun of prower and wear on the elevator.The elevator consists of a cam-shaped steel casting with a disc of mild steel plate on either side: These side plates project a few inches beyond the tips of the beaters, in order to prevent odd stones from straying in an undesired direction; they serve also to prevent extra large stones from reaching the beaters, for they slide off the rims into the water.

Jan 1, 1904

By L. R. Stark

Two wetland simulation experiments were carried out in order to determine the effects on manganese retention of several wetland design parameters, including flow rate, inlet pH, carbon supplementation, substrate type, and surface free water depth. The primary aim in each experiment was to determine if sustained manganese retention could be accomplished under the specific experimental treatments. If successful, these experiments could recommend design parameters for the construction of field wetland systems for manganese treatment. Crushed limestone clearly was superior to spent mushroom compost with respect to manganese retention. The presence of free surface water detracted from manganese treatment, while lower flow rates enhanced manganese treatment. Sustained manganese retention was achieved using crushed limestone as the substrate coupled with an absence of surface free water, under inlet water conditions of pH 7.0 and no appreciable iron. Sustained manganese retention was not achieved under reducing conditions using spent mushroom compost while varying flow rate, inlet pH, and carbon supplementation regimes. However, lowering the flow rate resulted in many significant beneficial effects on outlet water chemistry: lower outlet manganese concentrations (over the short term), higher outlet pH, lower outlet acidity, higher outlet alkalinity, higher outlet sulfide, lower outlet sulfate, and lower outlet redox potential. Supplementation of the wetlands with dairy whey resulted in lower outlet manganese concentrations (over the short term), marginally higher outlet sulfide levels, and acted to lower the redox potential under the high flow regime. Wetlands receiving a neutral pH had lower outlet acidity, higher outlet alkalinity, lower outlet sulfate, but equivalent outlet manganese concentrations than wetlands receiving an acidic pH. When manganese is the primary mine water contaminant and a passive water treatment system is to be used, it is recommended that crushed limestone with negligible surface water be used in place of composted materials. This recommendation assumes a source water with circumneutral pH and an absence of other metals.

Jan 1, 1993

By A. McGarr

The shear stress t that can be sustained by the rock mass in the environs of a mining-induced earthquake controls the near-fault peak ground velocity v of that event according to v=0.25(ß/G)t, where ß is the shear wave speed and G is the modulus of rigidity. To estimate t at mining depths, I review the results of four studies involving Witwatersrand tremors that relate to the bulk shear strength. The first and most general analysis uses the common assumptions that the seismogenic crust is pervasively faulted, has hydrostatic pore pressure before mining, and an extensional stress state that is close to failure. Mining operations reduce the pore pressure to zero within the mine and redistribute the stresses such that, in localized regions, the state of stress is again at the point of failure. Laboratory friction experiments can be used to estimate t in the zero-pore-pressure regime. Second, model calculations of states of stress in the vicinity of mining at about 3 km depth indicated the shear stress available to cause faulting near the centre of a distribution of induced earthquakes. Third, laboratory experiments combined with microscopic analyses of fault gouge from the rupture zone of a mining-induced event provided an estimate of the average shear stress acting on the fault to cause this earthquake at a depth of 2 km. Fourth, moment tensors determined for mining-induced earthquakes usually show substantial implosive components, from which it is straightforward to estimate t. These four different analyses yield estimates of t that fall in the range 30to 61 MPa which implies that near-fault particle velocities could be as high as about 1.5 m/s. To the extent that the causative fault ruptures previously intact rock, both t and v, in localized regions, could be several times higher than 61 MPa and 1.5 m/s.

Jan 1, 2002

By Bain J. H

Since zinc was first deposited at Risdon in February, 1917, provision of the most economical cathode assembly has been a subject of extensive research, the major problems being corrosion and efficient use of power.From the corrosion viewpoint, a perfect cathode is one in which the life of the headbar and the deposition sheet are the same. However, corrosion usually concentrates in a narrow zone across the face- of the sheet, resulting in breakages which, before the advent of argon arc welding, meant a loss of a 'complete assembly.Attempts to extend sheet life included use of thicker sheets, multitudinous protective coatings applied with varying degrees of success, re-rolling, and for a time, aluminium consumption was reduced when broken sheets found re-use as protecting strips. This latter economy became impracticable when electrode spacing was reduced for greater efficiency in power utilization.As an integral part of the electrode, the headbar was modified accordingly. Copper headbars, although more corrosion resistant, were replaced by aluminium due to a possibility of dissolved, copper promoting deterioration.Thicker electrodes and regulated spacing reduced internal shorting, whilst provision of knife-edge type supports on both contact and insulator ends of headbars aided in electrode centralising and continuous electrical conduction.After much experimeIitation, an assembly has been evolved which, with the aid of argon arc welding and tbe use of minimum additional aluminium, permits comparable headbar and sheet lives, combined with good electrical conduction throughout the life of the cathode.INTRODUCTION Over 300 tons of zinc are produced daily at Risdon from a purified zinc sulphate solution by electrolysis, the zinc being deposited upon all-aluminium (except for copper contact) cathodes. It is stripped in 72-hour cycles from the cathodes, melted and cast into the customary rectangular slabs.

Jan 1, 1958

By J. A. Finch, D. Lin

The robustness of the large-sections correction procedure, Hill's fast approximation, Barbery's correction and the PARGEN correction was examined by comparing their ability to reconstruct the true liberation distribution using sectioning data from computer-generated spheres. The results indicate that the flexibility of a correction procedure is related to the assumptions it makes about the continuity of the liberation distribution, locked-particle characteristics and ore texture. Overall, the large-sections procedure appeared to be the most generally applicable. The Hill fast approximation performed well, but this was probably because it partially incorporates the sphere model; the performance of the PARGEN and Barbery corrections varied from case to case.

Dec 1, 1995

By B. C. Lewis

Have technological advancements in underground coal mining driven people's skills to new highs or have the expanded skills of mining people driven the industry's technological advancements. Who knows? What we do know is that both our technology and our people have made meaningful and significant advancements. Overall, longwall systems continue to increase productivity and retreat faster. Globally, gate road development is the primary bottleneck in a longwall mine. The primary bottleneck in gate road development is roofbolting. Generally, roofbolting is the bottleneck in room and pillar operations as well. This paper will present an integrated manufacturer's (Joy Mining Machinery) vision of the future in comparison to current equipment performance. Particular emphasis will be placed on roofbolter technologies.

Jan 1, 1999

By L. M. Kaas

Production planning techniques, particularly a production scheduling model are proposed for use in taconite mining in Minnesota. Applications of the scheduling model, on a two-year mine plan, which evaluates the equipment involved, are detailed. Data and tables are included. INTRODUCTION Fifty years ago Walter Swart, a mining engineer investigating the Minnesota taconites for the Jackling interests, made this report: "There is no doubt in my mind that this taconite mining is a game worth playing and that it can be played to a successful finish. It seems now only a question of men, money, methods and details."' The prosperous industry envisioned by Swart and other taconite pioneers is today a reality. Its growth has been spurred by technological advances in mining and beneficiation, depletion of natural ore reserves, and improvement of the economic climate. However, the massive problems that were solved to make this development possible are only a foreshadowing of the questions of "men, money, methods and details" that will be encountered in the future. The increasing demands for higher quality taconite pellets have already forced producers to examine better methods of quality control for their operations. THE NEED FOR PRODUCTION SCHEDULING The maintenance of fairly constant crude ore characteristics is of major importance to mill quality control. Through careful mixing of ore from storage bins, the concentrator staff can partially reduce the deviations of the feed analysis from the analysis desired. However, the limited effectiveness of bin mixing systems has caused some mining companies to utilize large capacity blending piles to reduce grade variations. Although the analysis of material being reclaimed from such a pile is relatively uniform, raw materials still must be scheduled from the mine into the pile in such a manner that the average analysis of all material is close to the feed analysis prescribed by the mill. PRODUCTION SCHEDULING MODEL Minnesota taconite mining companies have used three analyses to estimate how a certain ore will react to concentration. These factors are the crude magnetic iron content of the ore, the iron content of the plant concentrate produced from the ore at a standard grind, and the grindability index of the ore. The actual laboratory tests used to determine these factors have been described by Apuli.2 These data are obtained from analysis of diamond drill cores, and are the established criteria used by mine planning engineers to formulate taconite production schedules. Variations in the grade of mine output should be controlled by any production scheduling system. However, to be truly practical, production scheduling methods must also consider many of the less tangible variables that affect mine operation. These include pit layout, available equipment, and ownership of ore leases. The number and scope of the variables inherent in this type of mine planning suggested that a computer simulation could be used to solve the problem. The preparation of information for use with a computer simulation program was the initial phase of this project. Meaningful data was developed from logs of diamond drill cores. Analyses were related to their respective areas of influence by means of mine maps, Fig. 1. The three assay variables and tonnages for each area were punched on cards. In addition to these values, a location code number was punched in the first eight columns of the cards. This code is explained as follows: Column 1 Bench number Column 2 Quadrant location as determined by mine reference lines Columns 3-5 East-west coordinate Columns 6-8 North-south coordinate The heart of any simulation techniques is a well engineered mathematical model. To develop a model for taconite production scheduling, the relationship between the three assay variables had to be established. Because changes in each analysis factor affect the mill circuits in different manners, a weighting system was used to determine the relative im-

Jan 1, 1967

When xanthates or dithiophosphates are used as collectors in sulphide ore flotation, adsorbed species may be identified by gas chromatography of the volatile products formed during low temperature pyrolysis. For collector additions ,as low as 20 g/tonne of ore, pyrolysis of the flotation products usually gives' an olefin directly related to the particular xanthate or Aerofloat reagent used. The method is able to provide valuable qualitative and quantitative data relating to the extent of collector adsorption and the resulting changes in the hydrophilic or hydrophobic nature of the mineral surface.

Jan 1, 1974

By H. K. VAN POOLLEEN, W. Hurst, H. C. Bixel

In an earlier publication* I showed the development of the instantaneous point source solution for a well producing at a constant rate at the center of a system of two radial, adjoining sands of different permeabilities. I also showed how a wellbore radius could be incorporated if this were the development required. For the purpose of that paper and the point I wished to make, this solution served. It yielded a simplifying solution of sands in series identified by Eqs. VI-26 and VI-27. (These equations are reproduced in part by Bixel and van Poollen as their Eq. 3, Page 302.) I am well aware that the simplified solutions are approximations. The facts that these Ei-functions satisfy the diffusivity equation and meet the boundary conditions both at the well and at the interface between sands, and that the earliest time considerations yield zero pressure drop, are evidence that the solutions are good approximations. This was the purpose for these formulas, which I interpret that where the permeabilities are of finite order of magnitudes in the respective media, the relations give satisfactory answers. However, from the authors' point of view there are reservations, which leads me to consider their entire generalization as illustrated in their Figs. 1 through 14. What I understand from their storage capacity, relationship Fs, which is the ratio of the product of porosity and compressibility of Sand II to Sand I, that is employed here by the authors as a correlative means of identifying one figure from another, there is nothing in the exact mathematics that supports such a term as a means of correlation. This is taken out of context, unsustained that this applies. Here the mathematics are known, where the true correlation is the diffusivity term of one sand to another. This entails permeability that refers back again to the term M in their paper for the transmis-sibility of fluid from one sand to the other that should have also been a part of this storage capacity. In Figs. 8 through 14, which purported to show the simplified equation following this correlation, there are apparent discontinuities for M equal to or less than 0.1000 that differ from the trends for greater values of M. In this connection there is no reference radius given for this cumulative pressure drop in the paper that would permit me to make these calculations. However, what is clear for M equal to 0.1000 or less we are treated to almost a closed barrier at the interface; a condition entered by the writers without qualification. This across-the-board treatment of these simplified formulas, whatever the motive of the authors, enters into a range of permeabilities that even I as the contributor would have reservations that such could apply. Under comparable conditions I would be looking at a closed reservoir or some facsimile for such. The extent to which the approximation or the exact equations pertain is not evident in the generality offered by Bixel and van Poollen in their paper. Only when they or other writers show the comparison of the pressure distributions within the formations can one be able to judge the rational limits to subscribe to the simplified formulas.

Jan 1, 1969

By G. A. Harrison

The introduction of extra low profile (XLP) mechanized equipment within Anglo Platinum is aligned with the overall New Mining Technologies strategy to focus on continuing modernization of our mining operations` incorporating injury-free production and cost-effective mining technologies. The method allows for the introduction of a suite of ultra-low profile equipment in narrow reef (1.2 m) stoping operations. For the first time it is now possible to achieve total trackless mechanization at these widths and indications are that XLP mining has the potential to add more value when benchmarked with conventional mining and low profile (1.8 m) room and pillar methods. Various mine layouts were tested at different sites within Anglo Platinum and the XLP breast mining layout proved to be the most effective. This paper describes the results of the trials at Waterval Shaft and concludes with recommendations on our future strategy on implementation of XLP technology within Anglo Platinum.

Jan 1, 2006

THE science of topography deals with the various natural and physical features of the earth's surface. These features are determined by the manifold constructive and destructive processes of nature, and their many diverse forms and characteristicsare dependent primarily upon geologic structure. Thus it is that a close relationship exists between the rocks of a region and the topographic features of the lJountry wherein they occur. Again, the existence of all sorts of mineral wealth is dependentupon the nature of the rocks, and their extension is directly connected with the topographic features represented upon the enclosing land-area.In studying any district with a view to deciphering its geological structure, to locating any mineral deposits it may contain, and to ascertaining, so far as a surface-examination may show, their probable and economic possibilities, it is therefore ofprimary importance to have at hand a correct topographical map of the area under investigation.GENERAL REMARKSThe actual amount of topographic detail shown will depend upon the money and time available for topographic surveying and upon the scale upon which the final map is to be produced...

Jan 1, 1912