Search Documents

By P. Bracher

Most efforts to mechanize low seam (narrow reef) mining of platinum ore are presently based on board-and-pillar methods with1.6?1.8 m in reef excavation. This paper attempts to substantiate the benefits of low profile mining: primarily improved head grade with resulting reduced tailings losses. Board-and-pillar equipment supplied by DBT, facilitating1.1?1.2m mining height has been in operation in an Anglo Platinum mine since September 2001. Major aspects of the equipment, battery scoops (LHDs) and rotary bolting rigs, are described and presently achieved results reported. The medium term industry goal is rock breaking without the use of explosives. An outline of present DBT developments is presented.

Jan 1, 2003

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine's carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

OWING to the gradual depletion of the hitherto plentiful supply of firewood in the immediate vieinity of Queenstown and Gormanston, which caused a steady increase in the cost of fuel for domestic purposes, the Mount Lyell Company took steps several years ago to make available as a substitute electric current from its Lake Margaret hydro-electric supply. In order to make this practicable it was necessary that the cost of electric power for heating purposes should compare favourably with the cost, of fuel, and the installation of domestic appliances brought within reach of the average householder, and efforts have been continuously directed towards this end since the year 1928.WATER HEATERSThe installation of electrical apparatus in local dwellings began with hot-water services, the heating elements being the types then procurable on the market and adapted to meet requirements.These, however, did not prove satisfactory, but the study of their bilure resulted in a type being developed locally which has overcome all difficulties. The first type of water heater evolved was an outside circulation one the element of which consisted of an iron pipe through which the water passed, insulated with micanite and wound with nichrome wire, the latter being covered with alundun cement to keep it in position and prevent oxidation. This was insulated on its outside surface with a layer of asbestos flour, and connected to the hot-water container as shown in Fig. 1. It was found, however, that the iron pipe had a short life, due to a certain amount of acidity in the water, and a copper pipe was substituted which proved very durable. Some heaters with this improved type of element are still operating after six years of use. The resistance wire is run at a very low current density, which ensures durability.

Jan 1, 1927

By Lon Santis, Dale Ramsey

The use of aircraft to support blasting operations in mines, quarries and construction sites goes back to the early days of aviation. Invaluable at times, aircraft use has been limited by cost, the unpredictability of weather impacts and other factors. Recently several technologies have matured to open up a new way to acquire aerial data with unmanned aircraft systems (UAS), commonly called drones. Equally important, the U.S. Federal Aviation Administration has recently implemented an exemption process and rulemaking to implement the commercial use of UAS into the United States’ National Airspace. The skies are opening for many applications of UAS. The most notable may be photogrammetry, which is the science of making measurements from photographs, especially for determining the exact positions of surface points.

Jan 1, 2016

By Stephanie Price

Engineering Associations ?Regulatory authority ?License individuals and firms ?Discipline licensed members ?Enforce against improper acts ?Programs for EIT?s, competence, etc

Oct 1, 2010

By Michael Schmitz, Eugene Ahrenholtz, William A. Heitbrink, Jeanne A. Zimmer, Andrew B. Cecala, Ernest S. Moyer, Earle H. Andrews, Chris C. Coppock, John A. Organiscak

Many different types of surface mining equipment use enclosed cabs to protect equipment operators from health and safety hazards. The overburden removal and mining process can be extremely dusty and can cause excessive dust exposure. To study this issue, a cooperative research effort was established between the National Institute for Occupational Safety and Health, U.S. Silica Co., Clean Air Filter Co., and Red Dot Corp. in an effort to lower respirable dust levels in an enclosed cab on an older surface drill at a silica sand operation. Throughout this research effort, a number of modifications were incorporated into the drill's filtration and pressurization system, as well as in other areas, to improve its design and performance. An average cab efficiency of 93.4% was determined with gravimetric sampling instruments when comparing the outside with the inside cab dust levels on the final design. Although this study considered just one operation, the goal was to identify cost-effective improvements that could be implemented on all types of enclosed cabs to lower respirable dust concentrations. Two critical components for an effective enclosed cab system are having a properly designed, installed, and maintained filtration and pressurization system, along with a method for maintaining structural cab integrity, which allows the cab to be positively pressurized. Another important component is maintaining cab cleanliness. Although this research was originally directed toward the mining industry, it is also applicable to agricultural or construction equipment.

By C. Sun

In this study, numerical simulations of yield pillars employing the finite element method with time-dependent Drucker-Prager material model are conducted. The stress control mechanism of yield pillars on weak floor strata is studied. The development of pillar yield zone, the distribution of pillar stress and the development of failure zone in the weak floor strata are investigated. The study indicates that a properly selected yield pillar size may significantly reduce the peak stress induced in the weak floor strata and effectively control the development of failure zone in the floor.

Jan 1, 1999

By J. Stacho, Frankovská. J.

"Abstract The use of continuous flight auger (CFA) piles in Slovakia has increased significantly in recent decades. High-rise building of administrative centre Lakeside Park in Bratislava is based on piled-raft foundation. The technology of CFA has been used due to the advantages of this technology in comparison with driven and bored piles in local geotechnical conditions. Piles have been designed in accordance with Eurocode 7. Resistance of piles was calculated by using an analytical calculation model for bored piles according to Slovak technical standard and CFA technology has been taken into account by coefficient equal to 1.1. Settlement of piles was calculated by using a calculation model which is being used in Czech Republic and Slovakia. Two well instrumented static load tests were carried out to verify the pile design. The results of static load tests showed that the design was conservative. The paper presents analysis of numerical modelling of CFA pile and static load tests. Load-settlement curves and load distribution curves over pile shafts are compared. Software Plaxis 2011 has been used for numerical modelling. Hardening soil model allows considering over consolidation of Tertiary Silts and water pressure in deep sandy lenses. The article also presents the parametric study where the influences of pile-soil interface reduction factor, over consolidation ratio and material models of soils are analysed. The results of numerical modelling showed that the most appropriate results have been obtained when the interface reduction factor equal 0.9 and real behaviour of groundwater were considered. The conclusion of the paper confirms that mechanical behaviour of the ground can be better understood and determined by using FEM than analytical methods.1. IntroductionPiles are among the most frequently used elements of deep foundations. Piles transfer loads down to a suitable bearing stratum when the soil immediately below a construction is unsuitable. Piles are also used to reduce settlement of structure. At present, the requirements of limit settlement of structures are more stringent. Examples of these structures are commercial and administrative centres that form a complex of different tall buildings. High-rise buildings cause greater contact stresses than connected low-rise buildings. Pile foundations in such cases should be placed under the high-rise buildings to achieve an appropriate settlement.Resistance of piles can be determined from static load test results, in-situ tests and empirical experiences or calculations. Static load tests give the most reliable results, but these tests are also the most expensive. This is the reason for constant development of computational methods. Especially numerical methods give more accurate results by using more sophisticated material models e. g. hardening soil or hypoplastic model."

Jan 1, 2014

By Paul Richardson

This paper will review several projects completed during the period from 1976 through 1984 which have been carried out utilizing big hole drilling concepts. The projects discussed will be from various industries to demonstrate the extent that big hole drilling methods are being used along with the current state of development. There will be a discussion of projects planned for the future where big hole drilling methods are the only technology being considered. Also included in the discussions will be an overview of the most recently completed heavy oil recovery project. During the next decade, big hole drilling methods will be used more and more in all industries where underground access is required. The safety, speed and economics associated with shaft sinking using drilling methods are becoming more and more recognized and the technology is rapidly becoming an accepted shaft sinking method.

Jan 1, 1985

By C. S. Spirakis, A. V. Heyl

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The modified basinal brines, containing partly oxidised sulphur species, scavenged metals from basement rocks and sediments and transported them through the host rock, which contained local concentrations of organic matter. Reacting in various ways with the mineralising solution as temperatures at the sites of mineralisation changed, organic matter caused the precipitation and dissolution of a variety of minerals in the ore zones; it was organic matter that caused all of these reactions to occur at the same sites. Thus all components of the mineralising fluid - salt, water, heat, sulphur and metals - were obtained within the ore district. The siting of the mineral districts was related to the locations of faults through U- and Th-enriched granites beneath sediments containing basinal brines, and the locations of ore deposits within the districts were controlled by local concentrations of organic matter

Apr 1, 1995

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By R. S. Dean

In addition to the normal work and that pertaining to strategic minerals, the Metallurgical Division has been made responsible for carrying on major investigations in the development of processes' for the treatment of low-grade domestic manganese ores that heretofore have failed to yield products suitable for the preparation of ferromanganese, an alloy essential to every ton of steel produced. These investigations are particularly important at this time because of their part in tucking this country self-sufficient with regard to manganese when the stock-piled ore becomes e exhausted and as foreign shipments of ferro-grade ore are cut off. The results indicate that there is a good probability of accomplishing this objective, while at the same time conservation may be promoted through the use of normally useless material from the large, low-grade ore deposits.

Jan 1, 1941

A series of electron beam, cold hearth, single melt Ti-6Al-4V plates (nominally 2.5 cm thick) impacted by 2cm diameter, 4340 steel projectiles (with 54g nominal mass) at velocities ranging from 0.633 to 1.027 km/s were sectioned along the impact axis and examined by optical metallography to characterize the formation, growth, and microstructure of adiabatic shear bands. Near ballistic limit velocities, the shear bands propagate towards the rear of the target where they coalesce and grow to provide a cylindrical solid state flow regime for the plug volume.

Jan 1, 2006

By Arthur M. Langer

Since the promulgation of the first Federal Asbestos Standard by the Occupational Safety and Health Administration in 1972, other federal agencies have modified the standard to better carry on their own unique missions. The instruments used to identify and measure asbestos, the sampling protocol, and the criteria used to define asbestos, have been modified to some degree. The Mine Safety and Health Administration regulates and controls asbestos dust in the mining and mineral commodity industries. However, crushed stone and processed ores contain mineral fragments that are frequently difficult to distinguish from asbestos. Mineral nomenclature, instruments for particle analysis, and sampling strategy must be accommodated to some degree to make asbestos control workable and meaningful. Precedent in other agencies has made consideration of these changes possible. Newly identified amphibole asbestos minerals have further complicated the agency?s regulatory charge. Changes in its Asbestos Standard are now being considered. Crushed taconite ore in the Eastern Mesabi highlights many of these issues. ©2008 Published by Elsevier Inc. Keywords: Amosite; Grunerite asbestos; Crocidolite; Riebeckite asbestos; Tremolite asbestos; Actinolite asbestos; Winchite asbestos; Richterite asbestos; Arfvedsonite asbestos; Fluor-edenite asbestos; Asbestos defects; Cleavage fragment; Mineral habit; Mesabi amphiboles

Jan 1, 2008

By Edmund J. Cardoza

The paper describes the design, construction and quality control aspects of the installation of a cement-bentonite (CB) cut off wall to impede seepage through a flood control dike. Special emphasis is placed upon the development of a proper specification, distinguishing the CB method from the Soil-Bentonite technique. The importance of the pre-construction laboratory testing program and field quality control procedures is emphasized by the fact that the in-place properties and characteristics of the CB cut off may not be known until after a majority of the work is complete. Sections are included which describe the construction method, the specialty equipment and personnel requirements and the quality control/quality assurance aspects of the project.

Jan 1, 1992

By P. Henning

Rock fall accidents continue to be the main cause of fatal and serious injuries in the mining industry. Although there has been an improvement in the FOG (falls of ground) related fatal and serious injuries over the past few years, the rate is still too high. New technology has made it possible to reduce this rate significantly. FOG accidents imply failure of the support system or the design of the support system in use. In this paper we deal with the latest technology available to assist the mines to reduce the rates of FOG related injuries and fatalities.

Jan 1, 2010

By W C. Cook, S J. Mathews, A H. Purvis

The Golden Cross Gold Mine is located at the head of the Waite kauri Ri ver, 8 km northwest of Waihi near the southern end of the Coromandel Range. The mine produces gold and silver from epithermal veins hosted by Miocene andesitic flows and pyroclastics of the Coromandel Group. Golden Cross is owned in joint venture by Coeur Gold NZ Ltd (80 per cent) and Viking Mining Company Ltd (20 per cent). Mining is by open pit and underground methods. Mineralisation in a near-surface sheeted/stockworked vein zone is mined from the open pit. The deeper Empire Vein System is mined from underground where higher grade mineralisation is restricted to generally discrete veins. The open pit stockwork zone is west of and offset from the updip trend of the Empire Vein System. The Empire (hangingwall) Vein strikes generally north-northeast and dips steeply west. Dips become subvertical at greater depth. The hangingwall vein is a well developed, generally continuous structure with relatively high gold grades. A complex footwall vein system forms shallow west-dipping offshoots to the hangingwall vein. Structure and gold grades become increasingly erratic away from the hangingwall vein. The better developed footwall veins carry economic grades and high 'spot' grades over 50 g/t Au are not uncommon. Highest gold grades are associated with tightly crustiform banded sections of quartz veins and with dark fine grained siliceous breccias. The main hangingwall vein occupies a major north-northeast trending fault structure, the Empire Fault. Footwall veining forms within subordinate splinter fault zones. There has been extensive multidirectional pre-, syn- and post-mineralisation faulting. Fault manifestation is highly dependent on host rock characteristics. The central part of the hangingwall vein and surrounding silicified country rock has been shattered by a major fault structure, the West Mine Fault, forming a poorly consolidated, blocky quartz-breccia ore zone. Away from the more brittle ore zones and associated silicified envelope, wide clay-filled shears mark the major fault trends. Development of the deposit is considered to have occurred in two distinct stages related to separate episodes of dilational jog movement on the Empire Fault. The first phase reactivated the pre-existing Empire Fault as a dilational fissure with subordinate splinters on the footwall side. The Empire Vein System (hangingwall and associated footwall veining) formed during this phase. A second phase of renewed movement with further dilation resulted in more extensive fracturing of the Empire Vein and surrounding country rock and formed the sheeted/stockwork veining of the open pit. An upwards/westward migration of the hydrothermal system is assumed but fluid pathways between underground and open pit veining are unclear. Ore extraction and mining geology methods have responded to improved understanding of the grade and structural variability, and changing ground conditions inherent in the vein system. The underground mine produces ore from flatback cut and fill, post-pillar and bench stopes. Open pit and underground ores are campaign milled through a conventional CIP plant.

Jan 1, 1993

By Verya Nasri

This paper presents analysis of damages and rehabilitation design for three major French rail-way tunnels built in mid-19th century. The La Nerthe tunnel underwent ovalization deformation with excessive displacement at the springline, and pinching and bursting of the liner bricks at the crown due to tectonic residual stresses with very high lateral earth pressure. The Saint-Louis les Aygalades tunnel invert was subjected to undulatory deformation resulting in tracks misalignment, which was caused by non-homogeneity of mechanical and hydraulic properties of the ground. The Roches de Condrieu tunnel required widening to comply with the increase in dynamic envelope of trains due to their larger cross section and higher speed. The applied rehabilitation methods and constraints of work in these busy mainline railway tunnels have been discussed in detail.

Jan 1, 2008

By W. Smith

The U.S. Bureau of Mines (USBM) is using laboratory and computer-based techniques to investigate the post- failure behavior of yielding pillars and pillar reinforcement techniques to control entry deformation. Poorly dimensioned yield pillars, can cause adverse ground conditions. Laboratory studies to evaluate various reinforcement techniques for controlling yield pillar deformation were conducted. A cracking and crushing model is used to evaluate potential tensile and compressive failure planes within pillars of various widths to assess the degree of yielding and stress redistribution. The use of an elasto-plastic model to evaluate the effect of various reinforcement on yield pillars is also discussed. These procedures effectively account for the residual pillar strength, important in yield pillar design.

Jan 1, 1995

By Remo Grandori

The Umiray Angat 13,2 km long tunnel in Philippines have been bored through extremely variable and difficult ground conditions including a number of special events. In particular the following adverse conditions were found: faults in decomposed ground, high temperature rocks, extremely rapid and important convergence phenomena, water inflows up to 800 litres per second. The special El Nino climatic conditions caused a long dry season and lower the level of the lake that was granting the access by barge to the site under the minimum navigable level. Many equipment have had therefore to be transported to site by a 10 ton capacity helicopter, after having been partially dismounted. For the same reason most of the tunnel drive have been bored servicing the site by 1 ton capacity helicopters to transport materials, spares and personnel. In order to overcome the above geological and logistic problems several innovation were introduced and tested in this project. Despite all that difficulties the 13,2 km of tunnel were bored in about 24 months, with a global average of 500 m/month.

Jan 1, 2001