Search Documents

By Orlando Ramírez

El presente trabajo describe el sistema integrado de seguridad a través de la norma OSHAS 18001 - 1999 y calidad ISO 9001 – 200m, donde la aplicación de la integración controla las desviaciones de los procesos oportunamente. Es decir, que a través de la procalsedad se reúnen tres elementos: productividad, seguridad y calidad,logrando una ventaja competitiva en el mundo globalizado.

Sep 12, 2005

By Chris Bennett, Glen Kosick

"Process modeling and equipment sizing procedures for SAG circuits has advanced significantly over the past two decades. However, no matter how exact the hardness tests, models and scale-up calculations, if the ore samples being used for design do not accurately represent the orebody then major design errors can be encountered. This paper will describe a hardness testing method for identiQing the power requirement profile of an orebody, to an extent that design errors due to poor sampling can be greatly reduced or avoided altogether. It will provide some insight into the magnitude of hardness variability that can be encountered in an orebody. Finally, the paper will preview how detailed hardness distribution data can be incorporated into mine block models, to optimize SAG circuit design for an orebody, both fi-om a capital investment and throughput point of view.INTRODUCTIONIt has long been known that many SAG/AG' circuits experience wide swings in throughput. These throughput variations are almost always of a magnitude not anticipated in the plant design; consequently, they are detrimental to the expected return on investment for the mining companies. It is clear that the throughput swings are mainly caused by changes in ore hardness. In 1993, in an attempt to address this problem, MinnovEX began investigating the possibility of using a small scale SAG test (2 kg charge) to predict SAG power requirements from drill core samples. The objectives of the small scale test were to enable mining companies to do many more SAG hardness tests than currently undertaken for a particular orebody. To make this possible, the SAG tests had to use a minimal amount of sample, be cost effective, and give acceptable accuracy in the prediction of SAG power. If this small scale SAG test proved accurate, then the high sampling frequency would yield results that approach the true hardness distribution of an orebody. This hardness distribution could then be used to derive the distribution and variability of specific energy required throughout the complete orebody. This specific energy (kWh/t) can be thought of as the power required to grind one tonne of ore per hour (kW/tph) to a specified size. Once the true distribution of power requirement throughout the whole orebody is understood, the grinding circuit design team can make an informed decision regarding the hardness value that is most appropriate for sizing the SAG equipment. Throughput losses due to hardness variation could be deliberately planned for or avoided altogether (a capital cost decision)."

Jan 1, 1999

The mining industry to the lay mind is one which appears peculiarly dangerous, partly because the accidents which take place are usually of a very tragic nature, and partly because other, industries claim victims more from disease than fromviolence, and their fatal nature is not advertised to the same degree so that in spite of this idea of unusual risk, it is a fact that mining will compare favourably, as regards vital statistics, with nearly all other trades requiring special training.Neverthelessthere are a larger number offatal and serious accidents occurring year by year than one would like to see, and could the deaths which take place by accident be eliminated, it is safe to say that mining would become one of the most healthy of all species of skilled labour. If we examine the accidents appearing yearly in the reports of the Mining Departments of the various colonies, it will be at once admitted that many of them need riot, and in many cases ought not to, have occurred.It is, therefore, the object of tbis essay, to pass under review the ordinary precautions which should be adopted to minimise, as far as possible, the dangerous factors whereby fatalities are brought about.

By Brian W. Stump, David P. Anderson, John Wiegand

Mining explosions are designed for a variety of purposes including the fragmentation and movement of materials. The blast design is dependent on the particular application intended and the material properties of the rock. The range of mining applications from hard rock quarrying to coal exposure to mineral recovery leads to a great variety of blasting practices.

Jan 1, 1997

By D. A. Bruce

To check the feasibility and the quality of a very deep diaphragm wall, a tern of adjacent panels has been constructed, up to a depth of 100 m, in the Milan sandy gravelly soil by means of a hydraulically driven milling machine with reverse circulation of mud. The results of the monitoring carried out in order to evaluate the panel geometry and the quality of both joints and concrete are described. The use of instrumentation based on different physical principles allowed the cross checking of measurements as well as the evaluation of the accuracy and sensitivity of each single procedure to be performed. The trial field was successfully carried out and the feasibility of a diaphragm wall of such a depth was demonstrated and corroborated by a reasonable level of quality control.

Jan 1, 1989

By D. Bessinger, J. M. A. Geldenhuis

High titania slag is produced from the smelting of ilmenite. These slags contain approximately 85 per cent TiO2 and consist mainly of a M3O5 solid-solution phase. During cooling the slag can decrepitate to a fine particulate material, which decreases the value of the product. Based on X-ray diffraction analyses of the decrepitated slag after cooling, it was found that the M3O5 phase had almost disappeared. The disappearance of the M3O5 phase was linked to oxidation of the slag. A M6O11 phase formed in the decrepitated slag. It is postulated that decrepitation of high titania slag is caused by volume changes due to the oxidation of the M3O5 phase in the slag.

Jan 1, 2005

By L. Nahai

An important objective of the Australian Government's policies on resources development is to encourage further processing of raw materials domestically, to the extent that this is economically feasible and consistent with sound industrial development. This Bureau of Mines report examines the extent to which Australia is able to pursue this policy in terms of its own competitive advantages and the implications of such a policy for the United States. Such factors as the impact of other competing producers and their advantages, expected world demand, and infrastructural problem--which may limit pursuit of this policy to the fullest extent--are discussed. After a broad review of the re-source, economic, social, and environmental factors, the perspective for increased processing is examined for a number of mineral commodities.

Jan 1, 1982

By Lorenzo Pellegrini

The respect of EPB reference pressure during TBM advance and hyperbaric activities, the complete and effective filling of the annular gap between tunnel lining extrados and the excavation section and a well organized monitoring system, to control surface settlements and ground distortion, are items of utmost importance in EPB tunnelling process. The paper describes how these concepts have been applied while excavating in the difficult underground conditions found at Sao Paulo (Brazil) during the execution of the Sao Paulo Metro Line 4-Lot 1. In this project, the annular gap has been filled by two components type, cement grouting. The back feed of the extensive monitoring campaign carried out to check the surface settlements during the excavation and hyperbaric maintenance operations will also be described in the paper.

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

Fire suppression systems are now recognised by both NFPA 502 and PIARC as legitimate tools for both life protection and asset protection. The effectiveness of these tools for life protection demands extremely rapid and accurate incident detection coupled with rapid response. This rapid response must be integrated with other emergency systems such as emergency ventilation. The March 2007 fatal Burnley Tunnel incident in Australia graphically illustrates the potential of effectively integrated fixed suppression systems to protect people from harm and save infrastructure from damage. Despite the raft of technology available in that instance to the operator it was the human operatorÆs ability to effectively control the emergency equipment and not the equipment itself which so positively influenced the threat to life and property.

Jan 1, 2008

By George G. Goble

The use of augercast piles has been limited by the engineer's concern for the structural quality of the installed pile. The nature of the pile is such that its final structural continuity is very dependent on the skill of the personnel that do the installation. Thus, NDT methods have been used to verify integrity and when problems are indicated the available solutions are usually quite costly. If information were available during the pile installation so that immediate steps could be taken to correct perceived problems, the concerns of the engineer could be addressed and the system would gain increased reliability. Pile Dynamics, Inc. has developed a quality control system, the Pile Installation Recorder for Augered Cast-in-Place piles (PIR CFA). This system consists of the following devices as shown in Figure 1. 1) The Control Unit powers the sensors, conditions the signals from the sensors, records all measurements, takes input information from the operator, displays the results, and stores the recorded data on a flash card for later permanent storage and processing. During the use of the system all of the results obtained during a test are seen during recording and can be reviewed on the screen again after completion of the installation. The ability to review the measured information makes it unnecessary to print a copy in the field. Since printers often give difficulty in the construction site environment the ability to review the results quickly after completion of the installation is an important capability.

Jan 1, 1997

By Nobuaki Sato

For the recovery of uranium from spent nuclear fuel, sulfide reprocessing process, which consists of voloxidation, selective sulfurization, and magnetic separation or selective dissolution steps, are proposed. In this paper selective sulfurization of rare-earth oxides in the presence of uranium oxides was studied by thermogravimetry and X-ray diffractometry. In case of the mixture with UO2, the rare earth oxides R2O3 (R=Nd, Eu, etc.) were preferentially sulfurized by CS2 formingoxysulfides and sulfides, while UO2 remained at temperatures lower than 500 °C. When R2O3was mixed with U3O8, first, the reduction of U3O8 to UO2 occurred at low temperatures followed by the sulfurization of R2O3. The separation of rare earth elements from UO2 in suspensionsolution by the use of permanent magnet was examined. The advantage of the proposed process was also discussed by compared with current process.

Jan 1, 2006

Geochemical projects in progress or recently completed in the Bureau of Mineral Resources, Geology, and Geophysics (BMR) cover a wide range of topics and include research projects, regional studies, and prospecting programmes. However, in these notes emphasis is given to projects which are directly relevant to mineral exploration.FIELD INVESTIGATIONSStream sediment sampling, rock and soil sampling, and geobotanical surveys have been used by the BMR in a number of areas, partly in attempts to locate specific zones of mineralization, and partly to investigate the effectiveness of the various methods under different conditions of climate and topopraphy and in different geological settings.Stream sediment sampling has been most successful in the Territory of Papua and New Guinea. For example, in the South Sepik area, zones of disseminated su1phide mineralisation were found to give rise to anomalies with peak values of up to 1,000 p.p.m. copper, compared with background values of about 40 p.p.m. (Dow et al., 1968). By contrast, the results of rather limited work in the Northern Territory and in the Kimberley district of Westen Australia were inconclusive.Rock and soil sampling, on the other hand, was successfully used in a number of areas in Northern Australia, particularly at Rum Jungle and Tennant Creek.Rum Jungle area In the Rum Jungle area, where uranium and base metal mineralization is mainly associated with a Lower Proterozoic black slate sequence, samples, of c-horizon soil or weathered 'rock are generally collectedfrom the bottom of drill holes, usually 15 to 20 ft deep, bored with a power-operated auger.Surface sampling indicates that such a technique would probably have shown up all the major geochemical anomalies delineated by deep sampling, but the latter gives slightly more consistent and slightly

Jan 1, 1970

By Lewis Stansfield

A rotary displacement method was used to install permanent steel casings for bored piles through an asbestos tip. This method was chosen in preference to alternative driven systems because it was quieter and more versatile if obstructions were encountered. New equipment was designed and made specifically for the project, and stringent health and safety regulations had to be observed.

Jan 1, 2000

By Holger Witthaus

Various seam conditions had been examined during longwall production at RAG German hard coal mines. Based on the field data a prediction method was developed considering separation planes as influencing factors for roof falls at the face. The characteristics, orientation, and density of separation are important factors on the occurrence of roof falls. In addition to geological influences, the performance parameters and geometry of support must be considered and optimized for the prediction and prevention of roof falls in a longwall face. Based on detailed macro- and microscopic investigations of e coal seams considering various ranks of carbonization, the origin and characteristics of separation planes are determined and a strata-specific influence on roof fall is interpreted. It was assessed that the coal face fracturing and displacement caused by the stress depend on the floor and roof strata conditions due to activation of the existing separation planes. Field studies are shown giving an idea of influences by advance rates of the longwall face, support delay and hydraulic pressure to the roof control in longwall faces in depth of more than 3000 ft. The analysis includes the application of specific software developed for longwall roof fall prediction as a result of a European research project. The software allows a laminar graphic display of roof fall probability, which is used for recognition of risk areas and risk management.

Jan 1, 2009

By N. R. Allen, J. D. Steenkamp

Oxidative roasting is applied on an industrial scale to beneficiate ilmenite concentrates from South African East Coast heavy minerals deposits - the aim is to increase the magnetic susceptibility of ilmenite to allow magnetic separation from chromite. The intention of this paper is to give researchers new to the field an overview of the beneficiation of ilmenite through roasting and magnetic separation, touching on the relevant fundamental aspects of magnetism.

Jan 1, 2005

Laboratory flotation tests on sized fractions of a certain number of selected minerals with homologous fatty acid derivatives (i.e. sodium salts and amine acetates) confirm that the higher homologues are more efficient collectors than the lower. Tests were carried out on sized material and finer size fractions floated at lower collector concentrations.It is suggested that selective flotation is best achieved with the reagent which most readily floats the most friable mineral in the ore, and that grade of product will be improved with the lowest usable homologue.INTRODUCTIONFlotation of non-sulphide minerals with fatty acids as collectors is usually less selective than the flotation of sulphide minerals with xanthate collectors. It is common to use the gradation in collecting power of homologous series of xanthates, as well as the more specific effects of activators and depressants, to achieve the separation of sulphides.The original aim of the work was to ascertain whether sodium salts of fatty acids (anionic) and fatty amine aceta:tes (cationic) could be selected from a homologous series to achieve better selectivity in separation of nonsulphide minerals by flotation. Subsequently the importance of friability of minerals in selective flotation was observed and the aim was expanded to develop a more practical approach to the testing of ore.MATERIALS USEDMineralsA series of massive mineral specimens, as pure as could be obtained, was procured. The specimens were cleaned by removing extraneous material, and then crushed and dry...

Jan 1, 1965

By K. S. Mortensen

The softwall mining system is a novel, new method of mining mineral deposits in soft, shallow, nonrock ground conditions. This method can mine the ore layer without substantially disturbing the existing overburden. The softwall mining system consists of machinery that is hydraulically controlled and powered, that can be buried (or used on the surface) to extract the ore or mineral from a layered deposit. The method is essentially an application of the longwall mining concept, modified for loose overburden and ore conditions, combined with hydraulic mining.

Jan 1, 2003

By Peter Hatherly

As a discipline, geophysics covers an enormous range of scales and applications - from planetary geophysics through to the monitoring of acoustic emissions of rock samples. Although it is not a core discipline within the mining industry, geophysics has a useful role in providing information on the nature of the rock mass and the way it is responding to the mining process. For coal mining purposes, geophysical studies mainly seek to - delineate boundaries between the coal and the various layers within the surrounding strata - determine the physical properties of the rocks in-si tu, and - monitor the response of the rocks to the mining process Some of these applications may be associated primarily with mine planning, but once a mine is underway, most geophysical results can be used for the purposes of ground control. For example, insights into the nature of a geological fault mapped by a 3D seismic reflection survey will be relevant to determining support requirements while mining through it. In some instances there are parallels in the use of geophysics by the petroleum industry. Seismic reflection and wireline logging techniques have mainly been developed for petroleum exploration where their on-going development continues to provide spin-offs for the coal industry. The 3D seismic survey techniques that we now routinely employ were in their infancy 25 years ago and, almost certainly, the high quality borehole scanning tools that are now available would not have been developed without the need for petroleum well evaluation. Mining has also led to the development of specific techniques. An example is microseismic monitoring for the management of roof conditions during longwalling, and also the prediction of rock and coal bursts. The use and success of this technique have grown greatly over recent years. Another example lies with the use of geophysical wireline logs to predict rock strength and in rock mass classification. Coal seams also provide an unusual geophysical situation in that they form seismic and electromagnetic waveguides. The in-seam seismic and radio imaging methods have been developed to exploit these geological properties. In this paper I address the development and application of geophysical methods such as these with a particular emphasis on their role in ground control. We will see that there have been many developments over the past 25 years but we should also think about the future and how geophysics needs to be developed. From a miner?s perspective, one obvious area of need is in the detection of voids in the vicinity of current mine workings, be they old workings or karsts within nearby carbonate beds.

Jan 1, 2006

By Michael B. Gilbert

The Woodbury L-73 Tunnel involved the design and construction of a 96-inch tunnel driven through 8,080 lf of very difficult ground conditions. Anticipated ground and groundwater conditions consisted of potentially flowing silty sand with cobbles and boulders, mixed face of sand and sandstone and full face of the St. Peter Sandstone. Actual conditions were similar, although the quantities did change from bid quantities. This paper presents the approach used for development of the GBR regarding risk management. The means of arriving at a fair compensation for variances from the baseline values to address the actual encountered tunneling behavior of the soil, boulder count and its effect on production rates are presented.

Jan 1, 2008