Search Documents

By Bret N. Lingwall, Byron Foster

The problem of reliable extreme event modeling of large diameter piles under enormous structural or kinematic loads has gained more attention in recent years. In particular, the soil response around the foundation and impacts to buried adjacent infrastructure has gained interest. One of the principal shortcomings with analysis of large diameter pile foundations under extreme event lateral loading is the reliance on conventional beam on elastic foundation methods, which do not model the soil field response around the pile. These methods are limited for large displacement problems, and for large diameter piles. However, the fundamental interactions between steel and concrete, and structure to soil are difficult to constrain, especially in large strain problems where the structural elements become inelastic. The non-linear interaction of the structural materials and soil is desirable so that assessment of stress changes in the field and effects on adjacent facilities can be modeled. A numerical modeling methodology that addresses these shortcomings has been developed. This method utilizes the interaction of brittle concrete with discrete steel reinforcing and casing in a robust manner capturing inelastic non-linearity in both soil and structure. This paper presents a comparison study of the method, wherein three different validation studies were made to data from full scale laterally loaded pile testing. INTRODUCTION Extreme event lateral loading of deep foundations comes in many forms including earthquakes, landsliding, tsunamis, hurricanes, surface fault rupture, liquefaction induced lateral spreads and many more. These extreme events induce loads on foundations far greater than service or strength loads. Perhaps the most dangerous extreme event loads are those of large soil displacements such as landslides, lateral spreads, and surface fault rupture, wherein the soil surrounding the foundations can move laterally 100 mm to 3 m! In these extreme event loading scenarios, small diameter foundations are pushed past their limits and many engineers prefer large diameter deep foundations for these situations. These deep foundations of diameter 900 mm or greater may be auger cast in place piles, cast in drilled hole piles, cast in steel shell piles, cased or uncased drilled shafts, bored precast piles, etc. For convenience in this paper, large diameter deep foundations will be referred to as Large Diameter Shafts (LDS). In LDS, steel may or may not used as a shell around the perimeter of the concrete and/or as internal tensile reinforcement. The interaction between brittle concrete and ductile steel within and/or along the perimeter of the LDS is critical to understanding the non-linear inelastic behavior of LDS for problems of large lateral displacements from extreme events.

Jan 1, 2018

By Dale Dean, Bill Hancock, Raul Mondragon, Carlos Aguilar, Chris Martin

"In 1942, commercial mining operations began in what is now the Lucky Friday Ag/Pb/Zn mine in Idaho’s Silver Valley. Wholly owned since 1962 by Hecla Mining Company, the mine has produced more than 145 million ounces of silver and has been a mainstay producer in Idaho’s Silver Valley for over 70 years.However, by the early 21st century, the mill had fallen, technologically, seriously behind the rest of the industry. Accordingly, starting in 2005, the current mill management team set to revitalizing the milling operation. This paper will describe how the mill was systematically evaluated and the aging infrastructure replaced with more current technology. Driven by internal mill review studies supported by QEMSCAN mineralogical balancing, the mill has in recent years been through waves of upgrading – from the installation of new mechanical and column flotation equipment to the introduction of on-stream analysis, a technology well-accepted around most of the industry but alien to this technologically conservative mining district.The experience at Lucky Friday is a testament to the need for ongoing structured mill optimisation and technology upgrading in established mining operations. This paper will describe engineering experiences associated with upgrading equipment in an operating mill, contained in a confined building. Experiences in teaching the team new ways of operating a mill, and finally the metallurgical rewards that have been reaped will be described.INTRODUCTIONMining in Idaho’s Silver ValleyIdaho’s Silver Valley is a 64-km long valley flanked by the US Northern Rocky mountains, seldom more the 3-km wide, and stretching across much of Idaho’s northern panhandle, roughly 150 km south of the Canadian border. Mining has been continuously active in the area for more than 140 years, during which time, the Silver Valley has become one of the richest silver producing districts in the world, and as of 1985 had out-produced the 500 years of production from the famed Potosi district in Bolivia. Since 1885, almost 100 deposits have been discovered and worked in the district (Chapman, 2000)."

Jan 1, 2011

By Peter Murphy

This report (arid related appendices) provides a description of the functional design specifications, engineering design specifications, and program of instruction for development of a training system for dragline equipment operators. Based upon a task analysis and training system analysis prepared under Phase I, Phase II efforts expanded upon and refined the functional design specifications. The training hardware components have been developed to a point shy of system fabrication. A detailed outline of the porgram of instruction and content sequence has been prepared. The objective of the training system described in this report is to provide new operators of dragline equipment with the requisite skills and knowledge to assure cost-effective development and an adequate supply of our human resources.

Jan 1, 1976

By Kerry Lahti, Bryan Ulrich

On Feb. 11, 2005, more than 20 mining professionals gathered in Elko, NV for a day-long round-table discussion on heap leaching. Attendees included project managers, operators and environmental professionals. They represented 10 mining organizations. Knight Piésold sponsored the special event. Its seven representatives included three staff members from the company’s Elko Operation, and one each from its Denver, Cajamarca (Peru) and Vancouver offices. The roundtable format was chosen to allow people from the mining industry to share ideas and experiences in an open forum. Rather than presenting prepared talks, spontaneity was encouraged. This resulted in a lively and enjoyable discussion.

Jan 1, 2005

By C. Gherghel

The planning and operation of ventilation network systems for uranium mines require special considerations since ventilation is the primary technique of controlling ambient concentrations of radon progeny. The major environmental challenge facing the ventilation engineer is the requirement to dilute radon progeny to below the Working Level Month per year of worker exposure required by law. The application of large airflow volumes and the utilization of low residence times constitute some of the factors considered by the design engineer. Good mine planning and sequencing are also critical for protecting the health of miners. The mine ventilation must have such characteristics as flexibility, high air distribution efficiency, rapid air transit times, zero recirculation and no short-circuiting. A well established maintenance program for all ventilation appliances must be in place to guarantee control of the distribution system. Real-time monitoring systems permit assurance the adequate quality of air is delivered to working places. A case study for an operating mine is used to demonstrate how the ventilation system is successfully managed and operated using the above concepts.

Jan 1, 2009

By L. Mabiza

Keywords: Pyrometallurgy, circular furnace, PGM, platinum, Peirce-Smith converter, Zimbabwe The Zimplats Smelter, located on the northern part of the Great Dyke, at the Selous Metallurgical Complex, is the only PGM smelter in Zimbabwe. Zimplats? operations currently consist of the Ngezi Platinum Mine, which is a 1.5 Mt/a open-cast and 0.7 Mt/a underground mine, and a Concentrator and Smelter to which ore is transported 80 km by road. The final converter matte product is transported to Impala Refining Services in South Africa for refining and marketing. The Zimplats Smelter operations consist of a concentrate filtration plant, a Drytech flash dryer, a modified Elkem / Hatch 13.5 MVA circular furnace, two 10? x 15? Peirce-Smith converters, and a matte granulation plant. The Zimplats smelter uses a three-field electrostatic precipitator, supplied by ELB-Brandt, for removal of particulates in the gas streams from both the converter and furnace. Construction of the smelter commenced in 1995, under the BHP / Delta Gold of Australia joint venture. The furnace was lined mid-1996, and smelting operations commenced in 1997. Due to design challenges, the Elkem furnace was modified by Hatch in 1998, and the smelter had not reached full capacity when operations were suspended in 1999. Re-commissioning took place in January 2002.

Jan 1, 2006

By Misra V. N

Upgrading of a Koolanooka magnetite iron ore sample provided by Kingstream Steel Ltd was investigated using low intensity magnetic separation (LIMS) and reverse flotation. The ore contained 38.6 per cent iron, 37.8 per cent silica, 6.5 per cent magnesia and 0.54 per cent alumina, with the main minerals in the ore being amphibole (42 per cent), magnetite (39 per cent) and quartz (14 per cent). The concentrate obtained after low intensity magnetic separation contained 66.6 per cent iron and 6.34 per cent silica with an iron recovery of 72 per cent. This concentrate was further treated by reverse flotation to increase the iron content and reduce the silica content to meet the requirements for direct reduction iron (DRI) feed grade.

Jan 1, 1999

By Stan Merjan

Composite piles with precast concrete tapered pile tips (TPT Composite Piles - U.S. and foreign patents) are a new and important addition to the piling types available to the construction industry. TPT Piles were invented by Stanley Merjan, Vice President of Underpinning & Foundation Constructors, Inc.. U. F. C. installs these piles in the Northeast United States and licenses piling contractors in other parts of the country. TPT Piles have been developed for use in sandy subsoils at depths to 70 feet or greater. The TPT system (see Figure 1) is simple. A pile stem of conventional material (shell, pipe, steel, wood, precast concrete) is connected to a socket formed in a precast concrete tapered pile tip (TPT). This composite assembly is then driven as a unit by ordinary pile driving methods until adequate driving resistance (established by formula or load tests) is met in a suitable soil strata. This driving resistance develops from the displacement and densification produced by the TPT. Many combinations of tip shapes and stems are available to suit particular job requirements with respect to subsoil conditions and pile capacities. TPT Piles should be considered for use on a wide variety of jobs. The advantages offered by a TPT installation include: ? High capacity piles in marginal soils ? Minimal lengths required to produce these capacities ? The use of conventional pile driving equipment and procedures ? Pile inspection techniques that are the same as for ordinary pile driving Furthermore, TPT piles are economical due to a combination of a low cost per ton of pile capacity and high productivity, both of which lead to significant savings in foundation costs and time required to complete foundation work.

Jan 1, 1987

By K. J. Gill, P. Chiotti

Thermal, metallographic, and vapor pressure data were obtained to establish the phase diagram for the thorium-zinc system. Four compounds corresponding to the stoichiometric formulas Th2Zn, ThZn2, ThZn4, and Th2Zn17 were observed. The melting points of these compounds under constrained vapor conditions were found to be 1055°, 1105°, 1095°, and 1015°C respectively. Four eutectics exist in this system with the following eutectic temperatures and thorium contents in wt pct: 1040°C, 89 Th; 945°C, 79 Th; 1045°C, 55 Th; and 995°C, 35 Th. The standard free energy, enthalpy, and entropy of formation for the compounds were determined from zinc vapor pressure data. ALTHOUGH the thorium-zinc system has been of technical importance in the commercial production of thorium and more recently of interest to some proposed pyrometallurgical separations processes for reactor fuels or blanket materials no detailed investigation of this system has been made in the past. Some previous work has been reviewed by Hanssen.1 The existence of four compounds, Th2Zn17, ThZn4, ThZn2, and Th2Zn has been established and their crystal structures have been studied by X-ray diffraction techniques.2-4 Smirnov et al.,5 determined the solubility of thorium in zinc and investigated the two-phase region between Th2Zn17 and zinc. They calculated some of the thermodynamic properties for these alloys from emf measurements on the cells Th/ThCl4(fused)/Cl2, C and Th2Zn17(s)+ Zn (l)/ThCl4(fused)/Cl2, C. The possibility of reaction between the anode materials and fused thorium tetrachloride to produce a lower valent thorium salt would have to be resolved in order to evaluate the results obtained. The purpose of the present investigation is to establish the phase diagram for the thorium-zinc system and to determine the standard free energy, enthalpy, and entropy of formation for the compounds formed. MATERIALS AND EXPERIMENTAL PROCEDURES The metals employed in the preparation of alloys were Bunker Hill slab zinc, 99.99 pct pure and Ames Lalboratory thorium. The major impurities in the thorium in parts per million were oxygen—1250, carbon—350, iron—100, nitrogen-75, and silicon—70. The metals in the form of several small massive pieces, total weight about 30 g, were cleaned with acid, washed with water and acetone, and dried just prior to their use for alloy preparation. Tantalum containers were found to be suitable for all the alloys studied and were used throughout this investigation. The metals were sealed inside of small 1-in.-diam tantalum crucibles by welding on preformed tantalum covers. A small thermocouple well made from 1/8-in.-diam tantalum tubing was welded in the bottom of each crucible. These crucibles were enclosed in

Jan 1, 1962

By NA UMC

Abstract Booklet

Dec 1, 2022

By Jørn H. Thomsen

This paper presents the experience gained and the lessons learned over the last decade within the numerous offshore foundation projects undertaken in the offshore waters of Denmark and Belgium by COWI A/S of Denmark. This experience derives from the close collaboration with, and interaction between the owners, contractors, and engineers in the various stages of project development. In turn, the experience draws on COWI's experience within foundation of large bridges world wide over half a century. Focus is on two pioneering gravity base foundation projects: ? Nysted in Denmark, currently the largest offshore windfarm worldwide with 72 Nos Bonus 2.3 MW turbines in water depths up to 10 m in the relatively benign inner Danish waters ? Thornton Bank in Belgium, where the first phase - comprising 6 Nos REpower 5MW-turbines of a total of 60 - are planned to be built in the rough North Sea in water depths exceeding 25 m.

Jan 1, 2013

By Madgwick J. C

A new strain of Thiobacil/us ferrooxidans (SPK I) has been isolated which has a higher copper to iron release ratio (2.04) than the standard T ferrooxidans (CPBI) (1.12). The diminished iron oxidizing ability enables almost quantitative release of copper (93 per cent) from a chalcopyrite-rich concentrate without interference by iron reprecipitation. In a single batch leach, Bougainville copper concentrate yielded 9.3 grams/litre soluble copper from a 4 per cent w/v suspension in 100 days at 32°C.Solvent extraction recovery of soluble copper is recommended as a final step in a leaching process.

Jan 1, 1983

By Qingwei Wang

Heavy metal-containing wastewater from hydrometallurgical processes of lead-zinc was treated by biologics in a 200 m3/h industrial scale experiment. The result shows that Zn concentration declined from 50.28 mg/L~240.81 mg/L to 0.21 mg/L~1.98 mg/L, Pb from 1.00 mg/L~13.47 mg/L to 0.083 mg/L~0.71 mg/L, Cu from 0.24 mg/L~2.38 mg/L to 0.059 mg/L~0.40 mg/L, Cd from 2.12 mg/L~23.47 mg/L to 0.011 mg/L~0.071 mg/L and As from 0.50 mg/L~6.00 mg/L to 0.005 mg/L~0.10 mg/L. The concentrations of the above heavy metals in the treated water were lower than that in Integrated Wastewater Discharge Standard (GB8978~1996) in China. Furthermore, the treated wastewater was recycled and reused in smelter plant. Zinc content in hydrolytic sludge reached up to 34.04%, which indicates that this sludge can be used to recover valuable metals.

Jan 1, 2010

By J. C. Bokros, A. S. Schwartz

The irradiation-induced densification of pyrolytic carbon has been shown to take place by a simple first-order rate process. The values of the densification constant, kd, for isotropic carbons are 1.0 x 10-22, 1.4 X 10-22 and 2.8 X 10-22 (nut)-1 at irradiation temperatures of 520o, 670°, and 1000oC, respectively. The apparent activation energy obtained from the temperature dependence of kd for isotropic carbons is about 0.2 ev. Estimates of the maximum stresses that develop in isotropic carbons owing to shrinkage onto an unyielding support show that stresses in excess of 15,000 psi may be avoided during irradiatian at 600" and 1000°C if the initial coating density is kept above 1.5 and 1.9 g per cu cw, respectively. If a carbon coating on an unyielding support is not completely isotropic, stresses may continue to build up at high neutron exposures after densification is complete because of continued anisotropic distortion. Stresses in excess of 15,000 psi from this source may be avoided during irradiation at 1000°C if' the Bacon anisotropy factor is kept below 1.3. A variety of applications of carbon and graphite in nuclear technology has stimulated numerous studies of the effect of neutron irradiation on these materials One of the most interesting problems associated with the use of carbons and graphites in the high fast neutron fluxes of nuclear reactors arises as a consequence of the neutron-induced dimensional changes that occur during irradiation. Energetic neutrons displace car- bon atoms from their lattice positions; and, depending on the temperature, the interstitials and vacancies produced migrate to form clusters, recombine, or are annihilated at dislocations or crystallite boundaries. The competition of various sinks for the point defects results in structure-sensitive bulk-dimensional changes that vary with temperature in a complicated way. This paper deals with the neutron-induced dimensional changes in turbostratic carbons that are being used as coatings on nuclear fuel particles. Details of the structure of these carbons and the variations of their structure with deposition conditions have been reported.'-3 It has been shown in previous work that the neutron-

Jan 1, 1968

By E. Amini

"While methods exist to allow the simulation and optimization of existing flotation operations, there is a deficit in the ability to predict the performance of a new ore type pre-processing. A laboratory scale batch flotation testing methodology has been developed to assess the flotation potential of ores (known as the JK Floatability Index or JKFI). Previous work conducted by Alexander and Collins (2008) showed that the test could be used to predict full scale results in base metal ores. In this work, JKFI tests were applied to three different types of ore and one blend from a greenfields gold deposit to show the test applicability to flotation of precious metals. The results from the JKFI test on one ore type were then used to predict the response of all ore types (including the blend). To validate the predicted kinetic parameters, a comprehensive survey was performed on a pilot plant where each of ore types was processed in the circuit. An acceptable agreement was found between the experimental recoveries and predicted recoveries which indicate the potential of this method for use in predicting the flotation response of an ore.INTRODUCTIONOver 100 years, flotation has been considered an efficient method to concentrate different types of sulphide and oxide minerals and coal. Thus, numerous research studies have been undertaken to find an appropriate model to predict the behaviour of particles in flotation circuits (Barnwal et. al., 2006; Bascur and Herbst, 1983; Cecile and Villeneuve, 1991; Deng et. al., 1996; Zheng et. al., 2006). Most methods are based on the ore flotation response in an industrial plant which is expensive and time consuming to characterise. It is difficult to reliably predict flotation response for new types of ores in industrial scale plants.The floatability component modelling (FCM) approach, developed within the Australian Minerals Industry Research Association (AMIRA) P9 project, has been used to derive models of operating flotation plants for the purpose of simulation and optimisation (Alexander and Morrison, 1998; Alexander et. al., 2000; Varadi, 2006). This approach has been applied at a large number of operating sites treating a wide variety of ores. The approach requires metallurgical surveys to be undertaken in conjunction with batch flotation tests and cell characterisation. This allows ore and machine parameters to be derived, which are then used in the P9 Flotation Model. The development of a FCM generally requires a large commitment of resources and time. While there has been significant support of this approach in industry, the FCM approach is limited to ores already being processed (Runge, 2004; Wightman, 2006)."

Jan 1, 2009

By A Rantala, K Aberkrom, O Haavisto, P Blanz

More complex ore bodies with lowering grades increase the challenges of maintaining high throughput, energy efficiency and required particle size for optimal downstream processing in grinding circuits. Continuous and often rapidly changing characteristics of the mill feed requires constant focus to operate the circuit at optimal level. Modern process instruments, on-line analyzers, monitoring and process control systems provide attractive and managed options to increase the circuits’ capability to respond to the challenge, often in phases and in rather short time period. Furthermore, well instrumented and performing base level automation in the grinding circuit enables advanced process control (APC) strategies that utilize measurements from the whole circuit to stabilize and optimize production. In this paper alternatives for incorporating process measurements and controls to typical grinding circuits are proposed. The expected benefits to throughput, availability, energy efficiency and particle size stability are described in recent case examples.CITATION:Rantala, A, Blanz, P, Aberkrom, K and Haavisto, O, 2015. Increasing grinding circuit robustness with advanced process control, in Proceedings MetPlant 2015, pp 129–141 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Vaughan J. P

The Pegmont deposit is a stratiform Pb-Zn sulphide body occurring in a thin, iron-rich metasedimentary unit situated near the top of the Kuridala Formation, a part of the Mary Kathleen Group of the Middle Proterozoic"Eastern Geosyncline" succession of the Mount Isa-Cloncurry district. The deposit appears to have developed in a shallow basin or depression on a sea or lake floor.Detailed chemical and mineralogical study of seven diamond drill cores through the ore horizon shows that in addition to galena and sphalerite the orebody contains a large range of iron-rich silicates and aluminosilicates.Further, five drill cores selected to represent a section from basin centre to basin edge exhibit clear and systematic chemical and mineralogical changes in the ore horizon in both a vertical and, most importantly, ill a lateral sense.Reconstruction of the sedimentary environment of the ore horizon as a whole shows this to be a silicate facies of a phosphatic, manganiferous iron formation or, more accurately, of "ironstone" in the sense of James (1966, U.S. Geol. Surv. Prof. Paper 440, chapter W).On the basis of both mineralogy and chemistry this silicate facies may be subdivided into three microfacies according to the dominant iron silicates characteristic of each: a fayalite microfacies, a hornblende-clinopyroxenemicrofacies, and a garnet microfacies. Significant Pb-Zn sulphide concentrations are confined almost entirely to the fayalite microfacies.

Jan 1, 1979

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By H. S. Martin

The Phosphate Recovery Corporation operates three flotation plants, Nos. 1 and 2 concentrators about three miles northeast of Mulberry, Florida, and No. 3 plant at Wales, Tennessee. These plants represent the first commercial phosphate flotation operation and are also believed to be the largest nonmetallic flotation operation in the world at the present time. The details of this paper will be confined to plant No. 2, this being the newest and largest concentrator in Florida, and the flow sheet being practically the same as at plant No. 1. The No. 3 plant has been operated but a short time and has been shut down since December, 1932, on account of the decrease in phosphate rock production. The phosphate washers usually are located centrally on a known deposit so that about two hundred acres of ground can be mined economically to each washer location. The washers are moved to new areas when the distance becomes too great for economical pumping. The flotation plants are built either adjacent to a washer, so that current debris may be utilized, or on the site of a former washer where there is sufficient accumulated debris available for mining, and the flotation plants must also be moved from time to time. Most of the water used in the Florida flotation plants is recovered after passing through a circulating system where most of the fine suspended matter is settled out, but some make-up water is obtained from deep wells near the plant. Power is obtained from the Tampa Electric Co. through the distribution facilities of the International Agricultural Corporation. Flotation concentrate is hauled from the plant by trolley over the International Agricultural Corporation's trolley system, to the drying plant at Prairie, one mile northwest of Mulberry. Ore Treated In the pebble phosphate district of Florida, the phosphate mineral, or collophane, is usually found in horizontal beds of varying thickness

Jan 1, 1935

By C. O’Hara, S. Roy, K. Swedburg, J. Katchen

"New Gold Inc.’s New Afton concentrator commenced operation in June 2012, producing a copper-gold-silver concentrate. During the first two years of operation, various optimization efforts have improved mill throughput, recoveries and concentrate grade. Daily mill throughput has increased 20% above the design rate. This was achieved through more consistent instantaneous feed rate and size distribution from the mine reclaim stockpile, higher pebble crusher reliability, changes to the SAG and ball mill grinding media sizes, larger SAG grate openings, reduced SAG discharge screen-deck aperture size and an increase in the maximum ball mill power draw limit. Metal recoveries at New Afton are primarily limited by liberation in the coarser size fractions; therefore, improving the grind size at a given mill throughput has been the main means of improving recovery. The average rougher flotation feed F80 size was reduced from 175µm in Q1 2013 to 165µm in Q1 2014, while the average operating mill throughput increased by 25%. Other flotation circuit changes focusing on recovery improvement include the addition of froth crowders to the rougher cells and the use of a stronger frother. The average concentrate grade increased from 22% Cu in Q1 2013 to 25% Cu in Q1 2014. This was achieved by redirecting the flash flotation concentrate stream to the regrind circuit and by the addition of lime to the cleaner circuit.This paper describes the above improvements made at the New Afton mill. The paper describes the objectives, timing and end result of each area of improvement.IntroductionThe New Afton Mine is situated approximately 10km west of Kamloops, British Columbia, 340km north-east of Vancouver. The mine has a moderate climate, access to transportation and electrical infrastructure, nearby fresh water supply, and close proximity to industrial and mining service businesses. The population of Kamloops is around 90,000 with most mine employees living in or around the city."

Jan 1, 2015