Search Documents

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007

By Michael Quadagno

Hudson River Pier 86, home of the historic USS Intrepid Aircraft Carrier and the Intrepid Sea-Air-Space Museum, is currently undergoing a $30M reconstruction. This project involves the demolition of the old timber pile supported pier and construction of a new 150 ft wide by 782 ft long concrete pier, built over the footprint of the old piles. The new pier consists of steel pipe piles, precast concrete pile caps, and a composite deck, made up of precast, prestressed concrete planks and cast-in-place concrete topping. This paper focuses on both the structural design and construction of the new pier, with emphasis on the pile foundation. Pier 86 is unique in that it is required to resist the extremely high lateral loads imposed on it by the permanently moored 898 ft long aircraft carrier during severe storms. A total of 360 steel pipe piles support the new pier. These piles, which are 24 in. in diameter and range in length from 58 ft to 175 ft, were driven down to bedrock. The piles, each having 200 ton allowable capacities, work together to resist the significantly large lateral loads exerted on the pier by the ship. The installation of the piles was unique in that all the piles, including the ?super-longs?, were fabricated to-length offsite, delivered to the site via truck and barge, and installed in one piece, eliminating the need for field splicing. The Pier 86 reconstruction will be completed within an extremely aggressive 18 month schedule, from January 2007 through June 2008. The refurbished aircraft carrier Intrepid will return home in September 2008, and the grand re-opening of the pier will be on Veteran?s Day 2008. This paper provides a case history for owners, government agencies, engineers, and construction professionals that will be faced with the challenges of designing and building new piers.

Jan 1, 2008

The purpose of this paper is to outline some aspects of the experimental worlr that has been carried out in the mineral dressing laboratory at M'ount. Morgan during recent years.The subject matter has been dealt with under the following headings:1. Comminution of various mill products.2. The application of sulphur dioxide as a flotation reagent.3. Heavy-media separation.4. Bulk flotation of sulphide ores.COMMINUTION OF VARIOUS MILL PRODUCTSThe following data were cbtained by processing fractions of reserve grade ore.Granular TailingIn Table 1 are shown the results of tests on material representative of average grade tailing. In the first test (H1 ) the granular tailing was floated as received and in the second test (Ha) the tailing was ground prior to flotation.

Jan 1, 1952

By Drew Floyd

Five full-scale pile load tests were performed on pairs of PZ-22 sheet piles installed with a vibratory pile driving hammer. The sheet piling was installed in several locations in soil generally consisting of miscellaneous granular fills overlying soft organic silts, inorganic silt interbedded with sands and gravels, very dense glacial till and shale bedrock. The test program also included the use of tip tell tales to determine what capacity could be attributed to tip resistance and skin friction. During the design phase of the project, it was assumed that the capacity of the sheet piles driven with the vibratory hammer could be correlated with the rate of penetration. The correlation between vertical capacity and rate of penetration would be used as a basis for determination of a driving criteria from driving the production sheet piling. The sheet piling load tests demonstrated that it was not possible to correlate the capacity of sheet piling driven with a vibratory hammer and the rate of penetration. It was also demonstrated that the capacity of the sheet piles was directly related to the density of the soil at or just below the tip. The results also tend to agree with empirical equations provided by Meyerhof (1976).

Jan 1, 1989

The sulphide ores of the principal lodes of the Boulder Mines are mainly composed of a schistose guess with a varying proportion of silica and lime, containing tellurides of gold, silver and mercury, associated with iron pyrites. It is a great difficultyto obtain pure and homogeneous samples of the tellurides for analysis, and from a number of tests made with excellent specimens it was found hardly possible to procure two to agree in analysis, the precious metals being found to be combinedwith tellurium in most varying proportions indeed, a close inspection of a partially crushed specimen will reveal, even to the naked eye, the various shades of colour characteristic...

Jan 1, 1901

By T A. J Hopper, B J. Birt, K K. Trofimczyk

Nuclear magnetic resonance (NMR) has been utilised in the oil and gas industry for over 60 years. The technology was recently identified as having potential value in iron ore, where latent bound moisture may affect ore handling even after dewatering and extraction. The first step in introducing this technology to iron ore involved laboratory tests on drill core samples. These results established the parameters for a downhole borehole magnetic resonance (BMR) tool for iron-rich environments, which was subsequently developed. A major challenge involved shrinking what is a very large tool in the oil industry to a slimhole, lightweight, 1-man deployable mining tool.Of primary concern was the ability to measure the very fast transverse relaxation times (T2s) seen in the lab results on iron ore samples. Iron creates local field gradients that significantly decrease the T2 times. As a result, the BMR tool had to be able to measure T2s in the range of hundreds of microseconds, a level not required in clastic sedimentary formations. The choice of T2 cut-offs in iron ore is critical to successfully separating the free and bound fluids. The industry has typically focused on T2 cut-offs in clastics and carbonates, but not in systems with high iron content. Using core analysis results (poro-perm and NMR) we were able to verify the BMR response. The T2 cut-offs were determined from NMR core analysis and then applied to the logs so as to provide a continuous, calibrated permeability log.Field results that highlight the challenge involved in logging in iron-rich environments are presented, as well as some minimum requirements for a successful BMR log. Examples from boreholes in an active iron ore mine in the Pilbara iron ore province in Western Australia are presented, as well as explanations for how NMR data can be combined with bulk density logs to provide a continuous dry weight density log based on the original density-porosity equation from Alger et al (1963).CITATION:Hopper, T A J, Trofimczyk, K K and Birt, B J, 2017. Development of a slimhole downhole nuclear magnetic resonance tool for iron ore – some applications and limitations, in Proceedings Iron Ore 2017, pp 473–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By H. Maleki

As mining continues toward deeper reserves in thick western US coal fields, the control of mining induced-seismicity has become a priority in many operations in Utah, Colorado, and Wyoming. Gradual floor heave, common in many coal mines, has historically not been a safety issue. However recent occurrences of sudden floor heave accompanied with seismicity in a few deep mines have fueled this investigation. The focus is to identify and study the mechanisms resulting in sudden heaving of the mine floor in western U.S. deep coal mines through analytical calculations and back analyses of an actual event in a cooperative mine. Based on review of available data in three mines, underground observations and back analyses of an actual event, the authors have identified the following contributing factors (1) presence of stiff stratigraphic units and thick seams mined at depths exceeding 1000-ft (2) presence of geological discontinuities reducing the in-situ strength of the coal with calculated factor of safety near 1 for the mine floor (3) mining approaching areas of higher than normal stress gradient associated with previous mining or structural anomalies or surface topographic highs and (4) an additional source of energy triggering sudden failure such as periodic caving or slip along geological discontinuities. Preliminary examination of seismic data for the actual event in the cooperative mine and underground observations excluded fault slip at the mining horizon as the triggering mechanism but highlighted the significance of weak, anisotropic strata conditions near the intersection of two faults.

Jan 1, 2009

By M. D. Max, A. H. Johnson

INTRODUCTION Gas hydrates have considerable potential to be a major energy resource owing to their apparent abundance in Arctic regions and along continental margins throughout the world (Kvenvolden, 1988). Yet, the oil and gas industry has been slow to pursue this opportunity. The primary reasons for this are the large conventional reserve base for natural gas worldwide and the perception that gas hydrate will not be a viable resource for another twenty or thirty years. Gas hydrates are thus viewed as a potential resource for the distant future, but not a valid investment for the near term. This paper addresses both global gas markets and gas hydrate technology, and shows that the commercial development of gas hydrate could proceed rapidly enough to constitute a near-term energy resource. GLOBAL GAS MARKETS The proven worldwide reserves of conventional natural gas are truly enormous, totaling over 6,000 TCF according to BP (2004). Moreover, those reserves have nearly doubled during the past two decades and now represent 67 years of consumption at the current production rates of 80 TCF per year (Fig. 1). This reserve increase has occurred even as global production of natural gas has increased by 67% during the same two decades (Fig. 2). While declining conventional gas reserves are a concern in North America, especially in regions where established infrastructure exists to bring gas to consumers, large new discoveries continue to be made elsewhere in the world. Indeed, in many parts of the world (such as the Middle East and parts of West Africa), natural gas has been regarded as an essentially worthless byproduct of oil production or exists in stranded gas fields. Given this situation, pursuing unconventional gas resources that are inherently riskier exploration targets and more expensive to produce would appear to have little rationale from a business standpoint.

Jan 1, 2006

Using a cylindrical hydrocyclone with a long vortex finder as the separator, a batch sizer was developed for the fast comparative sizing of the coarse solids normally encountered in mineral pulps.Operating times as short as 2 or 3 min gave separations ranging from 16 mesh down to the subsieve sizes.Reproducibility was good and sensitivity was adequate for most applications.

Jan 1, 1968

By J. Z. Cui

In this paper a statistical multi-scale method for the mechanics parameter prediction of the rock mass with random distribution of multi-scale cracks/joints is presented. First the micro-structure of the rock mass with random distribution of multi-scale cracks/joints is represented. Then the statistical second-order two-scale method for the mechanics performance predictions of the rock mass structure with random cracks/joints distribution is presented, including the statistical second-order two-scale expression on the vector-valued displacement, strain tensor and stress tensor, and the algorithm procedure of statistical multi-sale computation for the mechanics parameters. Finally some numerical results for mechanical parameters for the rock mass with random distributions of multi-scale joints/cracks by statistical multi-scale method are shown.

May 1, 2009

By D FitzGerald, S Jakica, R Paterson, J Silic

A new 2.5D airborne electromagnetic (AEM) algorithm has been developed by Intrepid Geophysics and Jovan Silic & Associates. The advantage of 2.5D (2D geology, 3D source) AEM inversion in 3D geological mapping applications and identification of conductive drilling targets, compared to the more commonly used conductivity-depth imaging (CDI) transforms or 1D inversions, are demonstrated using examples from banded iron formations (BIFs) and other geological settings. We show emerging AEM systems are capable of providing estimates of economic rock unit thicknesses, dips and fault definition at an accuracy that mitigates the need for pattern drilling.The 2.5D inversion application used in this work and described in Silic et al (2015) is a substantially changed version of ArjunAir (Wilson, Raiche and Sugeng, 2006), a product of CSIRO/AMIRA project P223F. The changes include a new forward model algorithm and a new inversion solver. The application enables the accurate simulation of 3D source excitation for full domain models inclusive of topography, non-conforming boundaries and very high resistivity contrasts. Solution is accurate for a geoelectrical cross-section, which is relatively constant along a strike length that exceeds the AEM system footprint.The major innovation includes a new inversion solver with adaptive regularisation, which allows the incorporation of a misfit to the reference model and the model smoothness function.Memory usage has been dramatically reduced and is estimated prior to execution. For speed the software has been parallelised using Intel message passing interface (MPI) and can be used on standard computing hardware or computing clusters. Data from survey lines with lengths exceeding 100 km can be inverted on high end laptop computers.We allow flexibility in the selection of components and in the estimation of noise.AEM inversion examples are shown for surveys from BIFs, base metals (volcanogenic massive sulfides) and geological mapping projects and the results are compared with known geology and drilling. We demonstrate the much improved mapping and target definition delivered by this inversion method when compared with the other more common transforms or inversion methods used on these projects.CITATION:Paterson, R, Silic, J, FitzGerald, D and Jakica, S, 2017. High accuracy .D airborne electromagnetic inversion method for banded iron formation and other geological settings, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By H Kurth

Geoscan is used for multi-elemental analysis of conveyed bulk materials in real time. It has been used for coal analysis since the 1990s, in the cement industry, and since 2003 for measuring mineral ore quality. Geoscan-M has proven performance and demonstrated paybacks of weeks or months, in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering and dust levels. Increments of two minutes (typically one to five minutes) are accurately measured and provide the plant operators with tonnage weighted results of each element within seconds.A Geoscan installed after crushing is able to measure quality shortly after mining. The analysis results can be used to divert the increments based on composition, such as diverting waste for disposal and diverting marginal material to a stockpile for processing at a later date. The bulk sorting process allows different qualities to be placed into relevant stockpiles for subsequent blending. Material meeting product DSO (Direct Shipping Ore) quality can bypass a beneficiation circuit to prevent unnecessary treatment costs. An analyser in a blending application enables proportioning of different quality feed materials from multiple stockpiles to achieve a desired compositional consistency for process feed. The parameter used for decisions may be; a) primary metal content, e.g. Cu, Fe, P, etc. b) deleterious component content, e.g. Mg as an indicator of talc content, c) process parameter content, or a combination of these. Process parameter content may be the elemental ratio between critical components, e.g. Cu:S ratio, Fe:Si ratio, basicity, Lime Saturation Factor, etc. or the content of an “indicator” element, e.g. Si as an indicator of material hardness or grindability.Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Compositional variability can be critical in the process and advance warning enables appropriate reactions prior to processing. This may include modifying the feed rate, changing the feed blend (through additives), or modifying reagent dosing in anticipation of a change in feed quality. Benefits include, but are not limited to; reducing waste processing, improved feed grade stability, reducing energy, water and grinding media consumption, producing less tailings, increasing process efficiency, higher metal recovery, better plant utilisation, reducing plant downtime, better utilising mined material, all achieved using the same process plant throughput capacity.CITATION:Kurth, H, 2015. Optimising plant feed quality and process performance using Geoscan elemental analysis, in Proceedings MetPlant 2015, pp 373–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By M. Tangstad, B. Monsen, H. Midtgaard, R. Ishak, M. Syvertsen, I. Solheim

Charcoal is an interesting reducing agent because it is produced from growing wood which is renewable and does not contribute to global warming, provided that there is a balance between the felling of timber and growth of trees. In the biocarbon project the possibilities for using charcoal is investigated as well as other biological based and renewable reductants for ferroalloy production. The background for the project is that the Norwegian ferroalloy producers wish to contribute to reduction of CO2- emissions. This paper focuses on the use of charcoal instead of coke for the production of manganese alloys, and the consequences of doing so. Results from practical SiMn smelting experiments on a pilot scale have previously been reported, where only 12-14 % Si in the metal was obtained when charcoal was used. Recently we have attained satisfactory 18 %Si also for charcoal, but good results are indeed dependant on good furnace performance. There is no tradition for using charcoal for manganese production in Norway. A change from using mainly coke to the use of some charcoal will demand new routines for furnace operation, raw material and off-gas handling. Hence, characteristic properties of charcoal, which may cause change of furnace operation, have been measured and are compared to coke. The following results are presented: ?Thermal abrasion strength together with CO2- reactivity; important parameters for the performance of the upper part of the furnace. ?Coke-bed resistance; it will increase with the use of charcoal (a review of new results). ?Slag reactivity; a relevant method for testing slag reactivity of industrial reductants is of interest. The suggested method can serve for comparing slag reactivities towards graphite.

Jan 1, 2007

By John J. Murray, Michael T. McRae, Michael A. Krulc, Kathy L. Schuler

The San Vicente Pipeline Tunnel Project involves the construction of an 8.5-foot-diameter water pipeline in an 11 mile tunnel in San Diego, California. The tunnel is located in extremely variable geologic conditions of strong granitic and volcanic rocks, weak sedimentary rocks, abrasive conglomerates, and mixed face conditions. One reach of the tunnel is a 5,200-foot mixed face reach that includes Friars Formation Conglomerate overlying granitic rock. Due to the variable ground conditions in this reach, the use of a TBM was deemed too risky and the contract documents required drill-and-blast and hand mining methods. Although it was not required, the contractor elected to construct this reach using NATM methods. This paper describes the geology of the 5,200-foot mixed-face reach, the design evaluation, and the construction challenges faced on this project.

Jan 1, 2007

By C. Sarkar

Increased competition in today’s global economy has put mineral industry under excessive pressure to effectively manage production assets to generate business wealth. Capital intensive industry (CII) organizations are seeking ways to manage skill resources, internal processes, and organizational networks with a view to reduce the cost of ownership of assets and increase efficiency of operations and service. The emerging concept of Enterprise Asset Management(EAM) is a collection of business processes that allow CII with right focus on return on investment on assets, to make right decisions on planning, acquisition, maintenance, operation, rehabilitation, and disposal of assets. Information technology (IT) can drive significant returns if the infrastructure covers seamlessly all business processes and all systems, like geographic information system, maintenance management, investment management, laboratory information management, and supervisory control and data acquisition system. The simple approach to IT in the past with disconnected silos of technology, information, and business processes cannot deliver the expected benefits under the modern business environment. Identification of business and application component is a prerequisite for the development of an asset management system that links effectively disciplined processes having characteristics of agility, speed, and integration. This paper discusses various issues and outlines the steps for developing an asset management roadmap in an organizsation. It also presents major business and application components of the system. Keywords: Enterprise asset management, Business architecture, Business component, Application component, Asset ownership, Asset operations, Information technology, Capital Intensive industry

Jan 1, 2003

By John E. Lens

How much trouble can narrow vertical fissures in bedrock cause on a shallow bedrock site? Enough trouble so end-bearing H-piles range between 8 and 100 feet long in a single pile cap and tiebacks range from 40 to over 100 feet long within a 10 foot wall span. Sloped bedrock surfaces also complicated the tieback installation as the drill casing followed the sloped rock surface while drilling and caused unanticipated bending (and sometimes breaking) of the drill string. Warned via pre-construction rock probes and cores reaching over 80 feet deep at the Winooski, Vermont project site, the design and construction team expected anomalies in pile driving and tieback drilling due to fissures in the bedrock filled with soil and weathered-rock. The degree of abruptness in the variability in the rock surface, and its impact on pile driving and tieback drilling were less predictable. Close monitoring of pile and tieback installation, redesign of pile caps, and lengthened tiebacks overcame these anomalous fissures. This paper shares the lessons learned for overcoming these geologic challenges to benefit designers, contractors bidding the work, and ultimately, the owner, with lower contingencies.

Jan 1, 2006

By Woodcock J. T, Jackson N

Wattle Gully Gold Mines N.L. of Chewton, Victoria, has decided to replace its present battery plant by a new mill to treat a free milling gold ore, after fine grinding, by concentrating coarse gold in a jig concentrate for amalgamation, and fine free gold and auriferous sulphides in a flotation concentrate for cyanidation. This paper outlines the economic justification and advantages of this step. In a review of the present position at the mine, a history of the company is followed by a description of the ore and its occurrence.Present treatment practice in two separate battery plants is described. Treatment tailings assay 1 dwt/ton gold and a substantial part of this gold is finer than 200 mesh.Experimental work showing how recovery may be improved is discussed and alternative methods of concentrating coarse gold mentioned. It is decided that the most suitable method for recovering gold from the ore is by jig concentration plus flotation.The merits of various flowsheets incorporating these techniques in the existing plant and in a new plant are assessed. It is concluded that there is no advantage in extending or converting the existing two battery plants, and it would be more economical and satisfactory to build a new plant.An economic study shows that for a capital expenditure of £120,000 a new plant could be erected to treat 70,000 tons p.a., working a 5-day week, and return an additional 14.2/- per ton, or £50,000 p.a., in revenue over the existing plant. It is estimated the plant cost can therefore be recouped out of savings inside three years. Probable ore reserves are sufficient to cover this period and additional ore will certainly be developed.INTRODUCTIQNSince 1934, Wattle Gully Gold Mines N.L. has been mining a lode gold ore at Chewton, near Castleniaine, and treating it by stamp milling and plate amalgamation, plus table concentration of auriferous sulphides. In 1954, following two years of unprofitable operation, a rehabilitation programme of all sections of the mine and plant was commenced. In the treatment section, two, major prospects for improvement...

Jan 1, 1959

By Ronald L. Bruening

IBC has developed a cost effective MRT process for the selective extraction and recovery of gold, copper, and a mixture of other base metals from mine leach cyanide solutions. This is a two-stage system in which the gold is first recovered selectively as a high purity salt. The copper is then recovered separately as a sulfate salt. The other base metals are then collected as a cyano anion concentrate. Three different SuperLig® materials are used. The first stage can be used alone on gold leach solutions where copper and other base metals are not a problem. The two or three stage system is used when the base metals build up in the leach solution, resulting in increased costs. The cyanide or cyanide/cyano anion concentrate can be recycled back to the leach solution until the build-up of other salts, etc. becomes too high, or this too can be controlled with a percentage bleed stream.

Oct 1, 2003

The Broken Hill orebody ,occurs in the Willyama Complex, a block of Precambrian rocks which have been strongly folded and metamorphosed at moderate to high grade. Although -the origin of the silver-lead-zinc mineralization remains obscure, recent investigations have substantiated the view that the orebody has undergone concomitant high grade metamorphism with the enclosing wallrocks. The mesoscopic structures produced by this metamorphism are described, and the possible processes Telating to their formation are disoussed.In the high grade ore, metamorphic structures which can be recognized are foliation and lineation, wallrock fragments, layering, flow folds, ore breccias, and sulphide bearing veins. These structures can be related to processes involving plastic flow and fluid phase transport of the mineral assemblage. 'In areas of low grade mineralization adjacent to high grade ore, the structures more closely resemble those produced in -the wallrocks-foliatlon, lineation, layering, folds, and sulphide injections. Within areas of high grade ore, lenses and pods of manganese silicates Probably represent original inhomogeneities in the ore, i.e., portions of manganese-rich and sulphide deficient rock which have been metamorphosed to manganese silicates.From the structures displayed, a sequence of events has been established for the plastic flow of ore during deformation.

Jan 1, 1975

By Charles Knilans, Tassos Grammatikopoulos, Nicole Hoffmann

"Twin Metals Minnesota LLC, (TMM) has recently completed a prefeasibility study evaluating the development and operation of an underground copper (Cu), nickel (Ni), platinum (Pt), palladium (Pd), and gold (Au) mining project on the Maturi deposit in northeastern Minnesota.The Maturi deposit is a magmatic Cu-Ni-sulphide deposit occurring along the basal contact of the South Kawishiwi intrusion, comprised of heterogeneous troctolites to gabbros forming a tabular body designated the BMZ (basal mineralized zone). These rocks provide the major gangue mineralogy (plagioclase, olivine, and clinopyroxene) with local, minor rock-forming orthopyroxene, biotite, magnetite, and ilmenite. Altered silicates exist within local fracture and/or alteration zones, which are commonly associated with minor faults in the regional area. The Maturi deposit is comprised of four main mineralized zones within the BMZ, referred to as Stage 1, Stage 2 (S2), Stage 3 (S3), and Upper Heterogeneous. Chalcopyrite, cubanite, pentlandite, and pyrrhotite are mainly hosted within the S2 and S3 units, with talnakhite frequently occurring within the S3 unit.A cross-discipline approach combining geology, geochemistry, metallurgy, QEMSCAN™ mineralogy, and mine planning has been implemented to develop a preliminary geometallurgical model and life of mine metallurgical performance forecast. This paper provides an overview of the methods that were used to develop the model and forecast, and discusses the advantages of such a model in project development and evaluation.INTRODUCTIONThe TMM Project proposes mining a copper-nickel-palladium-platinum-gold-silver (Cu-Ni-PGM) magmatic sulphide deposit situated in the Duluth Complex of northeastern Minnesota, USA. The prefeasibility study proposes a 45,000 million tonnes per day mine and concentrator facility to produce two saleable concentrates. The mine will access two separate deposits, Maturi and Maturi Southwest. Saleable concentrates are the final products of the sequential flotation plant where a high grade Cu concentrate is produced followed by a Ni concentrate."

Jan 1, 2015