Search Documents

By A. T. Robles, L. Buckingham

"When certain gold ores containing pyrite, graphite, humates and fumates or other organic compounds which are possibly adsorbed on clay minerals are treated with aqueous solution of alkali metal cyanide, the aurocyanide complex which forms is adsorbed by these ""pregrobbing"" species in the ore. Dissolution of gold proceeds until chemical equilibrium is attained between the cyanide complex adsorbed by the ore and in solution.Sodium lauryl sulfate (SLS) may be used to decrease the adsorptive activity of the prerobbing species in the ore. It has successfully improved recovery at Holt-McDermott Mine and is highly biodegradable.INTRODUCTION Precious metal-bearing ores containing preg-robbing species are poorly amenable to standard cyanidation techniques. The ""preg-robbing"" impurities with which they are associated tend to adsorb the gold cyanide complexes and carry them through the circuit to the tailings. Also, gold may be associated with these impurities in the ore and not be leached by the cyanide complexing agents used in conventional cyanidation techniques.Methods for dealing with the problem of preg-robbinq impurities in gold ores are:Carbon-in-Leach (CIL), in which granular activated carbon is added to compete with preg-robbing species for the gold cyanide complexes. This process can improve gold recovery in mildly preg-robbing ores especially when fine carbons with very high activities are used. However, with severely graphitic ore, the carbon associated with the rock may outperform the granular activated charcoal.Chemical Oxidation, in which the ore is subjected to preliminary chemical oxidation techniques to oxidize carbonaceous materials using such diverse reagents including ozone, sodium hypochlorite, calcium hypochlorite, chlorine gas, permanganates, perchlorates, chlorates and oxygen prior to subjecting the oxidized ore to standard cyanidation treatment to extract gold. This is generally a costly method and will not prove economical on a low-grade ore."

Jan 1, 1992

By Mike Boissonneault

It was three years ago when the “storm of the century” had taken a firm grip over the Pacific West Coast and inland areas. At the Big Sky ski resort in Montana on Christmas morning two ski patrollers set out to perform an explosives “hand charge” avalanche control mission that would see only one return. It has been difficult to determine exactly what happened. Investigators do know that there were three separate and consecutive attempts to light a safety fuse, when it had apparently been burning since the first attempt. Time ran out after the third attempt. Although this accident has had a profound impact on North American avalanche control programs, I am sure it pales in contrast to the shock and grief experienced by family members who lost a loved one.

Jan 1, 2001

By Sam Kangwa, Thomson Sinkala

Th e re are three basic types of hole deviations in long hole d ri l l i n g , n a m e l y collar i n g , alignment and tr a j e c t o r y dev i a t i o n s . In mining, the accur a cy in drilling has a significant effect on the effi c a c y and economy of mining oper a t i o n s . This ar t i cl e d e s c ribes the types, s o u r ces and effects of hole deviations in mining oper a t i o n s . The art i cle further demonstrates the economic consequences due to hole dev i a t i o n s .

Jan 1, 2004

By Marc Legault

The Duparquet mining camp situated along the Quebec segment of the Porcupine-Destor Fault was the site of gold exploitation from 1933 to 1956 and 1988 to 1991. Numerous gold showings and deposits straddle the fault. An ongoing regional metallogenic study by the Quebec Geological Survey has identified five main types of gold mineralization, each showing a distinct style, alteration, control, metal content, and timing. In order to maximise the impact of this study, a 3D regional common-earth-model was constructed along a critical segment of the Porcupine-Destor Fault with the gOcad® technology. The realisation of this model required the maximum use of the public SIGEOM numerical database, as well as the recovery of significant private data from exploration company partners. The 3D model is also a powerful new dynamic exploration tool, which can be queried using geological criteria characteristic of the different gold deposit types. This 3D model can be modified and improved continuously by adding data from new drilling, mapping or geophysical surveys. The case of the Porcupine-Destor Fault illustrates the importance of 3D common-earth-modelling in delivering refined technological geological syntheses likely to attract significant investments from the mining exploration industry, especially for deep exploration programs within mature mining camps.

May 1, 2004

By David Flores, Benjamin Cebrian

Gold mining require high levels of dilution control due the high value of ore. These types of operations employ short benches, which are suitable for ore control, lower displacement and more representative block models. However, shorter benches makes fragmentation by blasting difficult because blast designs tend to be stiff in regards to burden/bench height ratio. This is especially relevant in hard, massive ore bodies where usual drilling diameters lead to poor energy distribution. In regards to control ore loss and dilution, there are different techniques to minimize both, which include: panel blasting, buffer blasting to muck piles and differential loading of areas of the blast bench. All of them should be sequenced with appropriate displacement along the ore/waste contacts. This paper describes extensive engineering approaches to achieve both dilution control while not hurting fragmentation in the very hard, massive ore sections of a mine case study. Ore Tracker microchips are used to correlate performance of these designs at the SAG mill (bottleneck of this specific operation). Another gold mine uses the same technology to detect when and where operational dilution is happening. The system tells where flagging of the different ore bodies has been followed in order to detect which operators pass the excavation limits beyond ore control flagging.

Ore samples generally require preparation before analysis. Serious problems can occur with contamination degradation and particle size effects. Both grinding element contammation and sample cross contamination havebeen bound to be related to sample hardness and operator technique. For best results with minerals relevant to the steel industry, the use of Siebtechnik-type mills required a combination of careful planning, short grinding periods and intermediate sieving of the sample. The results may be extended to most mineral, rock, and refractory sample preparabons.

Jan 1, 1978

By Jason Rrno

The emergence of Impact and Benefit Agreements (IBAs) in the Canadian mining sector has been read by many as a positive governance innovation. Negotiated directly between mineral resource developers and Aboriginal communities with limited government interference, IBAs serve to manage impacts associated with a mining project and deliver tangible benefits to local communities. Notwithstanding their increasing use and significance, limited systematic analysis has been undertaken to determine whether they are, in fact, working. This paper reports on the effectiveness of a number of IBAs negotiated in support of three northern Canadian diamond mines, drawing on evidence from time-series data, key informant interviews, and focus group meetings in Yellowknife and Dettah, NWT, and Kugluktuk, NU. While some deficiencies were apparent and perceptions of effectiveness varied somewhat by Aboriginal community, the IBAs were generally found to be meeting their objectives, especially with respect to the delivery of benefits. For Aboriginal communities affected by mineral development in the Canadian North, this represents a significant change to typical outcomes of the past. Moving forward, research on IBA effectiveness needs to adopt a longer timeframe and begin to gauge the degree to which IBAs are able to address long-standing concerns associated with hinterland resource extraction beyond their agreement-specific objectives.

May 1, 2010

By Jörg Fischer-Bühner

Conventional 22ct Au jewellery alloys are comparably soft in the as-cast and soft-annealed state and hardening by cold-working is the only way of giving strength to the jewellery. The paper first focuses on hardening of 22ct jewellery alloys by conventional means, i.e. solid solution hardening with base metals (aiming particularly at an increased as-cast hardness) as well as precipitation hardening by alloying with base metals beyond the solubility limits and subsequent age-hardening heat treatment. Co-additions of ~2% turned out to result in most pronounced solid solution hardening up to ~100 HV1 in an investment cast & quenched state. Subsequent heat treatments, consisting of solution annealing at 850°C for 1h followed by water quenching and ageing at 300°C ? 400°C for ~ 1h lead to pronounced age-hardening with a peak hardness of ~ 260 HV1. In contrast, 22ct Au alloyed with Ni, Fe or Sb display no age-hardening effect within the same range of heat treatment parameters. The 2nd part of the paper reports on some preliminary trials to enhance the hardening effect of the base metals by additions of suitable elements, which possess a strong tendency to phase formation with the added base metal during ageing treatments. It is shown, that the age-hardening behavior of 22ct and 990/995 Au alloyed with Co or Ni can be remarkably influenced by additions of Sb. A total of only 10wt%0 of CoSb or NiSb-additions lead to a peak hardness of ~ 150 HV1 for a 22ct Au and ~ 100-120 HV1 for 990 Au , which is obtained already after very short ageing times (20-40min) at 300-400°C after solution annealing at 700°C / 1h / water quenching. It is suggested that the age-hardening mechanism in these alloys consists in precipitation of intermetallic CoSb- and NiSb-phases.

Oct 1, 2003

By B. Arjang

ABSTRACT: Ground stresses are one of the significant factors in the context of rockbursts and underground instability at some hard rock mines in Canada. Overcoring strain relief measurements using triaxiaI strain eel is were performed at depths between 60 to 1890 m at several mine sites to provide stress data for stability analysis and optimum mine design. Pre-mining ground stress determinations from 64 stress tensor analyses resulted in the following average stress gradients: Maximum horizontal stress. -Hmax - 8.18 - 0.0122 MPa/m depth Minimum horizontal stress. _-,,min - 3.64 - 0.0276 MPa/m depth Average horizontal stress. -11, 5.91 - 0.03-19 MPs m depth Vertical stress. '-, - 0.0266 - 0.008 MPa/m depth The maximum and minimum horizontal compressive stresses. with an average ratio of 1.75 ,0..45. prevail in east--west and northerly directions. respectively. Horizontal compressive stresses in excess of vertical overburden load were determined. indicating large variations in ratios to a depth of about 1000 m with decreasing trend towards depth. From present data. a particular regional zoning for the magnitude and direction of horizontal stress fields cannot be outlined. A common feature at mines with near vertical orebodies is that the maximum horizontal compressive stress acts perpendicular to strike while the minimum horizontal compressive stress is aligned on-strike. The vertical stress components approach the gravitational overburden load.

Jan 1, 1989

For the past four years, the Department of Mining Engineering at the University of Kentucky has conducted a validation study of the CFD Fluent code, by comparing its results against mining-related benchmark experimental data provided by NIOSH?s Pittsburgh Research Laboratory. This particular study is dedicated to the effect of machine-mounted dust scrubbers on the performance of face ventilation systems using extended-cut mining with a blowing curtain.

Jan 1, 2009

By F. Dahl, P. Raleigh, J. Holzhauser, B. Nilsen

Tunnel excavation using tunnel boring machines (TBMs), has become increasingly common in recent years, despite the fact that precise evaluation of certain risks have not kept pace with the use of these machines. One of the risks easily overlooked by Engineer and Contractor alike are the effects of abrasive ground on the costs and schedule of a given project. The impacts of worn and damaged TBM cutter heads have been observed on hundreds of tunnel projects around the world. It would appear that a reliable prognosis of the abrasiveness of soils on a project would be of great importance for designers, clients and contractors alike. Several well acknowledged test and prognosis methods already exist for rock, however there is only very limited knowledge available to describe the abrasiveness of soil and its impact on soft ground TBMs. This paper will examine approaches to this problem and suggest a new approach based on a current project undergoing design.

Jan 1, 2007

By Jochen Belz, Allan Henneker, Nod Clarke-Hackston

For the construction of tunnels and other underground structures, extraction of the exact amount of material is of paramount importance both economically and for engineering purposes. In the Sequential Support Method (NATM) immediate (sequential)and smooth support by means of shotcrete, steel arches, lattice girders and rockbolts, either singly or in combination are used; cutting of the precise (albeit sometimes of complex geometry) profile is an integral part of the method. In order to save unnecessary excavation and provide better information to the machine operator, VMT GmbH has developed a system to support precise excavation of the tunnel profile when using road headers or other partial face cutting machines. This paper outlines the principles of this system with examples from Australia, Ger-many, Sweden and Spain and will cite examples of typical savings achieved.

Jan 1, 2007

By Woodcock J. T

A sulphide ion selective electrode (ISE) is suitable for control of sodium sulphide additions in flotation because it has a rapid response to changeS in S2- concentrations, can indicate -low concentrations at differentpH values, suffers from few interferences, and is robust enou'gh to use in a pulp. Three sulphidization techniques were studied using the lSE electrode for measurement and/or control of S2- levels. Metallurgy was assessedfrom concentrate grades and copper recovery.With slug additions of sodium sulphide, sulphidizing conditions were poorly defined and reproducibility tended to be poor. Although acceptable metallurgy could be achieved by multiple additions, sodium sulphide consumption was high.Controlled potential sulphidization readily gave good metallurgy. The optimum potential of the lSE for sulphidizing was about -500 mV versus SCE, but depended on sulphidization and flotation times; suitable times were3 and 5 min respectively for three to five stages. Application of this technique to previously untested ores gave good metallurgy in a first test in spite of variation by a factor of three in the sodium sulphide requirements ofthe ores.Simultaneous sulphidization and flotation was satisfactory when conducted at an lSE potential of -450 mV versus SCE. Mixed cha!copyrite-oxide copper ores responded satisfactorily.Besides optimizing sulphidization conditions it is also necessary to optimize xanthate additions (e.g. by measuring xanthate residuals).

Jan 1, 1978

By R. F. Favreau, Patrice Favreau

"A blast with explosives creates vibration waves in the zone around the blast.The prediction of the intensity of vibrations is important because people in the cinity demand that the vibrations do not disturb them, and society imposes limits on the vibrations. The U. S. Bureau of Mines (USBM) showed that the easurement of the particle velocity U predicts the risk of damage from vibrations. A currentapproach of blasters to monitor vibrations is to measure them with a seismograph at several distances S, and create a graph of U vs. S and the explosive charge “W” according to the equation U = K / (S / W)N where K and N are constants that depend on the blast method and the nature of the ground over the distance S. Though useful, this equation is empirical, and the results predicted from it are very variable, as shown by figure 1 which indicates that a prediction of U can deviate significantly from the actual value. Moreover, a minimum of two seismograph measurements at two values of S are required to establish the curve. However, here now exists another very convenient method to predict U; it is with the simulator Vibmas, which is based on the fundamental principles of how a blast reates vibrations. This simulator takes into account not only W but rather all the blast parameters, the type of explosive and the properties of the rock. Moreover, to establish the calculation of U as a function of S, only one seismograph measurement is required rather than two as for the USBM method. This last difference is important because it makes it easy to predict U not only as a function of S, but also as a function of the orientation of S. On the site this allows much safer control of the vibrations, and the use of larger explosive charges which reduce excavation costs. The article presents results from a field case at a hydroelectric project in Canada, where the deviation was very moderate. Use of this vibration simulator on the Web is very easy."

Jan 1, 2015

By R. C. Burtan

Long before recorded history, man began to dig into the earth's crust in a never ending search for useful materials. It is well known that more than half of the earth's crust is composed of silicon dioxide (SiO2), also known as silica. Silica and silica-containing material have a great many uses in modern society. This material, however, is potentially an extreme health hazard. Silicosis: Not a New Disease Centuries before the Christian Era, Hippocrates wrote of a lung disease common to those who mined in hard rock. He was obviously describing silicosis. It is also apparent from ancient writings that the Egyptians were aware of this malady. Dioscorides also wrote on this subject in the fifth century B.C. It is undoubtedly the oldest and best studied of the occupational lung diseases. Silicosis was certainly described by Agricola in his De Re Metallica published in 1556. Here he described lung disease among hard-rock miners. The original document was written in Latin and then translated in 1912 by Hoover and Hoover. One of these translators was Herbert L. Hoover, a former US president who once made his living as a mining engineer. More recently, there are numerous references in medical literature in the 19th and 20th centuries relating silica exposure to silicosis. There are specific references to mining in hard rock, as well as to sandblasting and a host of other industrial exposures. In 1919, Winslow described standards for measuring the efficiency of exhaust systems in polishing shops using sandblasting. These standards were equally applicable in the mining industry. As early as 1920, Winslow explored the efficiency of certain devices used to protect sand-blasters against the dust hazard. These devices were equally applicable in the hard-rock mining industry. The medical community recognized the silica health hazard in the early 1900s. Middleton described the illness in the British Medical Journal in 1929. He noted the danger to health at that time. D. Hunter mentions in his book, The Diseases of Occupations (1969), the monumental work of Merryweather in 1936, in which he surveyed the silicosis risk in Great Britain. He showed statistically that the average employment length of sandblasters who ultimately died of silicosis was 10.3 years, compared to 40.1 years for all fatal cases, irrespective of occupation. Sandblasting and hard-rock mining and drilling, obviously, are very hazardous occupations. Weil and Zisking of Tulane University wrote in 1975 that "it was known as early as 1935 that the course of silicosis is much more rapid in sandblasters than in miners or foundry workers. This can be explained by the fact that sandblasters are exposed to an almost pure siliceous dust containing high concentrations of respirable particles within the range of 1 to 3 micron size." Protecting the Worker The medical community recognized in the early 1900s the need for proper protective equipment for all of those who worked with siliceous materials. Middleton, writing in 1929, said: "The worker is then protected by a close fitting helmet with an air feed, much as in the case of an underwater diver. In spite of these precautions, cases of silicosis among sandblasters are being met with today. It is a matter for serious consideration whether a substitute, such as steel or iron grit, could not be used to replace the siliceous grit as the abrading material." C. E. A. Winslow, a professor of public health at Yale School of Medicine, and others wrote of the need to protect sandblasters by

Jan 7, 1984

ALTHOUGH the development of the various flotation processes during the last 8 years has been so revolutionary, this development has been, until recently, entirely confined to the separation of the gangue from the mixed metalliferous sulphides.The desirability of finding some method of separating the independent sulphides from such a miXture, by means of flotation, has long been recognized. ThIS need was emphasized when the slimes resulting from the grinding of Broken Hill sulphide ores were for the first time successfully dealt with by the Mineral Separation Company's process on the Central mine. This process proved the practicability of separating the sulphides of lead and zinc as a mixed concentrate from the gangue present in slime. Although this was a very notable achievement, the process has not been generally used, owing to the mixed lead and zinc concentrates resulting from the treatment being acceptable neither to the zinc nor the lead smelters.Although the introduction of eucalyptus oil in minute quantities as an emulsifying agent has simplified the work of the subsequent tabling of mixed sulphide concentrates, rendering unnecessary the burning off or removal of the oil, there will always be a considerable quantity of slimy product too fine to settle on the moving surface of the concentrating machines, and therefore requiring other means for its division into lead and zinc concentrates.

Jan 1, 1912

By H. Sis, D. Dahlin, S. Chander, C. Summers

Bench-scale selective-flocculation tests were conducted on samples of Florida and Western phosphate process tailings. Physical, mineralogical, and surface characteristics were determined for both types of samples. The flocculation tests investigated dispersant and flocculant types and doses, pH, and slurry percent solids, while other parameters were held constant. Where selectivity was achieved, phosphate minerals remained dispersed, whereas silicate minerals flocculated and settled. In single-stage tests, flocculants having low to medium anionic character effectively upgraded products at moderately elevated pH. Multiple-stage tests, and tests in which flocculants of lower molecular weight were used as site-blockers, gave improved results.

Jan 1, 2002

By Michael G. Rulff, Tracy M. Holmes

"Vast amounts of time and money are spent fighting flow problems in plants that involve the handling or processing of industrial minerals. Because these types of projects tend to be capitalintensive, the right decisions, made at the design stage, can have a substantial positive effect on the economics of the project.Some of the problems related to solids flow in mineral processing plants include:•,Flow stoppages•,Uncontrolled flow•,Segregation of blended materials•,Build-up and dead material resulting in loss of live capacityUnfortunately few Universities in North America provide courses in the design or selection of bulk solids handling equipment, let alone the theory of bulk solids flow, with the result that engineers do not fully appreciate the effects of bulk solids handling on their process. The usual method of selecting “standard” equipment, all too often, leaves plant operators hammering on hoppers to promote flow, a technique that is not only usually ineffective but also unsafe and often causes damage to equipment. In short, too little consideration is given, at the design stage of projects, to the particular material and operating environment involved and how these will affect handling between process steps.This paper seeks to give a general understanding of bulk solids flow theory including flow patterns and flow property tests, and presents functional design guidelines to ensure reliable flow. As well, a case history will be presented. Our message is clear: To ensure uniform, reliable flow, a plant design must take into account the specific flow characteristics of the bulk solid to be handled or processed."

Jan 1, 2008

By Andreas Brandner

"At the beginning of 2007 the Austrian contractor PORR was awarded with remediation works for a 48-km long part of the railway line from Campina to Predeal – part of the Trans European main Corridors TEN-T priority line 22 Bucurest – Brasov, connecting the southeast European countries with the heart of Europe.Due to partly new realignment and change of regular sections as well as protection against rockfall and slope slide a huge bunch of slope stabilization works became necessary, which were awarded to the contractor PORR and their designer IB-Brandner.Following the studies of the tender documents for the planned protection measures responsible managers of PORR decided to propose an alternative protection design by IB- Brandner. Changing the original design a more flexible and environmentally compatible solution consisting of high performance net, soil nailing and rockfall protection systems (fences) was elaborated and adapted to local needs. During design process, several critical areas were identified and additionally taken into account.In the paper examples of the design and erection process show how difficulties in implementation starting with the presentation of the idea continuing to the realization on site were managed and a technically more sophisticated and commercially competitive solution could be delivered to the customer Romanian Railway – case study.The European Commission awarded – following an election process in which all citizens of the EU could join - the remediation project Railway line Campina – Predeal in Romania as the environmentally best EU co-financed infrastructure project. GENERAL PROJECT EVALUATIONDue to original design slope stabilization should be done by concrete slabs fixed with prestressed anchors and shotcrete cover.The area to be secured was limited to a 12-meter strip left and right from the railway track without reference to nature and local needs. Discussions with the client and his designer and rising awareness for the hazards to address took several months. Site visits in Austria to provide insight in the problems of dealing with natural hazards helped to convince the client of the needs and our alternative design."

Jan 1, 2017

By George W. Toth

Uranium in situ leach mining has recently emerged as a viable alternative to conventional miring techniques. The cost implications of in situ mining are therefore of increasing interest to mining paracticioners as well as public officials. This report presents the results of an assessment of uranium in situ leach mining costs through the application of process engineering and discounted cash flow analysis procedures. A computerized wasting technique, termed a cost model, was developed through this effort to facilitate rapid cost analyses. Application of this cost model will generate mine life capital and operating costs as well as solve for economic production cost/lb. U308. Conversely rate of return may be determined subject to a known selling price. The data bases of the cost made! have been designed to reflect variations in Texas vs. Wyoming site applications. The results If applying the model under numerous ore deposit, operating, wellfield and extraction plant conditions for Texas and Wyoming are summarized in the report. Sensitivity analysis of changes in key project parameters have also been tested and reported.

Jan 1, 1981