Search Documents

By W. G. Davenport

This chapter examines three minor influences on flash smelting's industrial oxygen and oil requirements, i.e.: (a) recycle of molten converter slag to the flash furnace (b) gangue oxides and carbonates (e,g, Ah03, CaC03) in the flash furnace feed (c) minor sulfides (e.g. NiS} in the flash furnace feed. It then examines the. sensitivity of our flash furnace calculations to previously ignored aspects of smelting chemistry -Cu, S and Fe304 in slag and 0 in matte.

Jan 1, 2001

By John L. H. Patterson

Handheld XRF has become the favorite way of measuring the content and identity of alloys in the field. This is because of the very portable nature of the instrumentation and its simple operation. However, these analyzers have been unable to determine the concentration of the light elements like Mg and Si due to the very low energy of the x-rays produced by these elements. In the past accessories such as vacuum and He flush have given some analyzers the ability to determine these light elements with modest detection limits. The introduction of the Silicon Drift Detector (SDD) into this class of instrumentation has added a new level of analysis capability to portable XRF instrumentation. X-ray fluorescence is achieved by exciting a sample with a beam of x-rays, which in recent portable equipment are generated by a small tube. This results in the emission of characteristic x-rays from the sample under test. By measuring the energy of each x-ray it is possible to determine what element generated it. By counting the number of x-rays at each energy it is possible to determine the concentration of each element. The detection limit for each element is dependent upon the number of x-rays which reach the detector. As the number of x-rays increases the detection limit will improve. One of the major factors in an x-ray reaching the detector is the energy of the x-ray. As the energy of an x-ray increases the probability of that x-ray reaching the detector increases. The energy of an x-ray is inversely proportional to the atomic number (AN) of the element generating the x-ray. For example, an iron x-ray (AN=26) is 6.40 keV while an aluminum x-ray (AN=13) is 1.49 keV. As the energy decreases, the detection of the x-ray becomes less and less probable because the x-ray may be absorbed by the windows which are part of the instrument and detector or the air in the path between the sample and detector. In SiPIN based portable XRF analyzers, the lowest element which is detected with acceptable detection limits is normally considered to be Ti (AN=22). The detection limits for 60 second measurements on typical SiPIN XRF analyzer are given in Table I. Thus, portable analyzers have not been useful for measurement of aluminum and titanium alloys as major components of these alloys are Mg (AN=12), Al (AN=13) and Si (AN=14).

Jan 1, 2009

By Fuqiang Guo

Scorodite (FeAsO4, 2H2O) is suitable mineral carrier for immobilization of arsenic-rich wastes. Its stability is, however, highly pH dependent (typically at 4 ≤ pH ≤ 7) and satisfactory only under oxic disposal conditions. In thiswork an encapsulation process using mineralized gels of aluminum hydroxy-oxides is developed to enhance the stability of scorodite under wider pH and redox potential range conditions. The encapsulation involves blending and ageing of synthetic scorodite produced by McGill’s atmospheric scorodite process with aluminum hydroxyl gels derived from controlled hydrolysis of aluminum salts. The amorphous hydrolyzed Al-gel encapsulates the scorodite particles,which upon short-term aging transforms into crystalline Al (OH)3/AlOOH mineral phases providing a robust protection microscopic barrier. Long-termstability testing demonstrates the encapsulation systemto be highly effective in suppressing arsenic release under either oxic or anoxic (100 mV < Eh < 600 mV) potential and neutral-alkaline pH (7 ≤ pH ≤ 9) ranges.

By Shu-cai Zhou

"To understand the solidification behavior of austenitic heat-resistant stainless steel (TP34 7) in rotary electromagnetic-field, the influence of electromagnetic stirring in mold (M-EMS) on solidification structure of TP34 7 heat resistant steel in a round billet continuous casting was investigated based on industrial experiments. The results indicate that the excellent billet solidification structure of TP34 7 heat resistant steel can be obtained with appropriate electromagnetic stirring parameters. The solidification structure of TP34 7 heat resistant steel can be remarkably refmed, central porosity and shrinkage cavity can be remarkably decreased and equiaxed grains zone widens was enlarged. The industrial trials verify that the stirring intensity of TP34 7 heat resistant austenitic stainless steel should be higher comparing with plain carbon steel. Due to a higher viscosity, rotating speed of molten stainless steel was 20-30% lower than that of molten carbon steel in the same magnetic flux density.IntroductionIn recent years, the development of ultra super critical (USC) plants is accelerated by the demands of environment protection and energy saving, and USC plants with steam temperature and pressure conditions in excess of 593°C and 24.lMPa respectively were constructed. To achieve the goal, it is important to develop new materials with excellent high temperature strength, superior resistance to oxidation and corrosion at high temperature. Besides, their cost must be low enough to meet the requirement of plants [ 1]. TP34 7H steel is promising austenitic heat-resistant steel, which is used as superheater/reheater tube material and is extensively used for high temperature components and fossil-fired power plants, and suitable to be used in USC boilers plant. This kind steel contains with about 0. 7%Nb and it keeps higher allowable stress and creep rupture strength than TP304 and TP321H [1-2]. TP347H has conventionally been produced by ingot casting followed by forging and rolling. Recently, in order to decrease the production cost, challenging trials to produce these types of alloys by a continuous casting (CC) process have been attempted. However, the solidification structure of austenitic stainless steel is one of the key issues that attract more attention. Due to the low thermal conductivity of TP347H heat resistant stainless steel (much smaller than that of plain carbon steel), pronounced defects during continuous casting of austenitic heat-resistant steel such as coarse columnar, center porosity and coarse bridging, greatly influence mechanical properties of fmished products.A widely used technique in metallurgy is the inductive drive of molten metals using rotational or traveling magnetic fields. Recently, rotary electromagnetic stirring (EMS) has been applied to reducing various defects and improving increase the solidification structure of the metals in the continuous casting of steel, Al-based alloys and Mg-based alloys [3-8]. Electromagnetic stirring of plain carbon and low alloy steel in the continuous casting bloom and slab is well established for improving the quality of cast products [9-11] and is widely used in industry. However, very few literatures on electromagnetic casting of heat resistant stainless steel have reported. In this work, an industrial plant trial was performed to clarify the effect ofM-EMS on the macroscopic quality ofTP347heat resistant steel billet, in which the regularity and mechanism of the influence of EMS on solidification casting billet were discussed."

Jan 1, 2014

By Feng Liu

A thermal upgrading process by which nickel value can be concentrated in a ferronickel alloy is a possible alternative to treat Sudbury pyrrhotite (Po) tailings with nickel content of 0.5–1.5 wt%. The basis of this process is precipitation of Ni from Po at high temperature once Fe/S ratio in the iron-deficient Po is shifted towards stoichiometric or near stoichiometric FeS (troilite) either by the addition of iron and/or the removal of sulfur. For the iron addition route, the reaction between elemental iron and nickeliferous pyrrhotite to produce ferronickel alloy and Ni-depleted iron sulfide phase plays a critical rule. In this paper, the formation mechanism of ferronickel alloy was investigated using the diffusion couple technique to better understand the nickel diffusion behavior in the iron and sulfide phases.

By T. Sakaguehi

Some attempts were made to recover and remove of uranium that may be present in refining effluents, mine waste Water, and other waste sources by using microbial biomass. To establish which microorganisms accumulate the most uranium, 135 species of microorganisms (42 bacteria, 26 yeasts, 34 fungi and 33 actinomycetes) were screened. Of these 135 species of microorganisms tested, extremely high uranium absorbing ability was found in Pseudomonas stuzeri, Neurospora sitophila, Streptomyces albus and Streptomvces viridochromogenes. In addition to the research on uranium uptake, thorium recovery by using microorganisms was investigated. High abilities were found in Streptomyces levoris and Bacillus subtilis. The selective accumulation of heavy metal ions by various microorganisms has also been examined. Uranyl, mercury and lead ions were readily accumulated by almost all of the species of microorganisms tested. Actinomycetes and fungi differ from many bacteria and most yeasts in their selective accumulation of uranium, and mercury. The basic features of uranium uptake by Streptomyces viridochromogenes, a microorganisms with high uranium-uptake ability, were investigated systematically. Synthesizing these results, we suggested that the accumulation of uranium into these microbial cells is not directly mediated by any metabolic process:, but almost completely dependent upon physicochemical adsorption on the cell components. In addition to this fundamental research, uranium recovery was investigated in immobilized Streptomyces viridochromogenes. These immobilized cells adsorbed, uranium readily and selectively. The immobilized cells recovered uranium almost quantitatively and almost all uranium adsorbed was desorbed with 0.1 N Na2CO3, These results showed that microbial cells are more stable after Immobilization and can be used repeatedly for the process of uranium adsorption-desorption. These results suggested that these microbial cells can be used for the recovery and removal of nuclear fuel elements, such as uranium and thorium, from refining effluents and mine waste water.

Jan 1, 1991

By Jose M. Gomez-Vega, Osamu Takai, Atsushi Hozumi, Hiroyuki Sugimura

"Ongoing research is reported aimed at improving the properties of mesoporous silica-based coatings on various substrates for optoelectronic or medical applications. Tetraethylorthosilicate (TEOS) was selected as the silica precursor, and amphiphilic triblock copolymers poly( ethylene oxide)- poly(propylene oxide)poly( ethylene oxide) as the surfactant micellar template or structure-directing agents. Cetyltrimethylammonium chloride (CTAC) was also used as a control agent. The effect of the templating agent and type of substrate (glass, Si, and Ti) on the mesoporosity, particularly on the alignment of the mesochannels, has been investigated. Three · different treatments (thermocalcination, photocalcination, and solvent extraction) have been also studied to remove the organic templates.IntroductionThe fabrication of mesoporous silicate-based materials through the utilization of a sol-gel process, where cooperative organization of organic and inorganic species takes place, provides a versatile approach to nanoscaled structures with potential applications in fields such as catalysts, optoelectronics, biomaterials, etc. Compared to conventional low molecular weight surfactants, self assembly of amphiphilic·block copolymers can result in mesostructured materials with larger pore sizes (up to 30 nm).1 Most of the synthetic strategies use silicon alkoxides as the silica precursor, although non-silicate metal alkoxides, e.g; Ti, Zr, Al, and B, have been also used to obtain different mesoporous materials, or even mixed metallic oxide systems. 2 Recently, Yang et al. 3 • 4 were able to synthesii:e a great variety of mesoporous metal oxides ID nonaqueous media using inorganic precursors (metal chlorides) and block copolymers as structure-directing agents."

Jan 1, 2000

By Saeid Pournaderi, Ahmet Geveci, Ender Keskinkilic, Yavuz A. Topkaya

"This study investigated calcination behavior of one of the Turkish laterite deposits, which was recently found in Sivrihisar region. Representative limonitic laterite samples (1.26% Ni) taken from Yunusemre Karasivritepe and Kucuksivritepe location were first subjected to drying. Removal of chemically bound water and other volatiles were then studied, in detail. In the calcination experiments, temperature and time were the main experimental variables. Thermal treatment was conducted at the specific temperatures in 250 °C - 800 °C range. The weight losses due to elimination of chemically bound water and other volatiles were reported to be approximately 10 per cent of the weight of the ore. For the particle size used in the current work, 700 °C and 40 minutes were determined to be the optimum calcination temperature and time, respectively.IntroductionThe nickel ores that are economically valuable can be grouped into two categories: sulphide type nickel ores and oxide type nickel ores, namely laterites. Over all reserves in the world, 40% are sulphide nickel ores and the remaining 60% are laterites [1]. Pyrometallurgical nickel extraction from sulphide type nickel ores is conducted via matte smelting. More recently, laterite ore bodies have been subjected to nickel extraction. Depending mainly on the chemical composition of the laterite and the process economics, various extraction techniques have been implemented: pyrometallurgical route involves ferronickel smelting. High pressure acid leaching (HPAL) is the commercial method for hydrometallurgical nickel extraction, while ammonia leaching (CARON Process) is a combination of pyrometallurgical and hydrometallurgical processes [2]. With the improvements in these processes, it is predicted that laterite’s share in the world nickel production will rise to 50% in 2012, while it was reported to be 42% in 1,200,000 tons of annual production in 2003 [3]."

Jan 1, 2011

By Darrin Wikoff

"The data, compiled by the Department of Energy (DOE), indicates that the average industrial plant could reduce its total energy cost by 14.8% by implementing effective Life Cycle Asset Management processes. The actual savings varies by industrial classification, but in all cases the potential is substantial and could have a marked impact on the operating profit of the company.Improvements geared towards improving equipment reliability have distinctive linkages to environmental performance, such as reducing the amount of product and raw material waste through routine monitoring of system parameters through predictive technologies, and preventing interruptions to production cycles with a focus on Overall Equipment Effectiveness (OEE).Alcoa successfully reduced solvent disposal costs by more than 40% and GE reduced greenhouse gas emissions by more than 250,000 metric tons. This presentation will show you how companies have successfully reduced energy and disposal costs through a focused effort on manufacturing process reliability.IntroductionSmelter in the ParkThe quaint town of Portland, Victoria protrudes outward towards Antarctica from Australia’s southeastern coastline. Portland is a quiet rural community surrounded by agriculture that draws tourists by the thousands to the southernmost edge of Victoria by way of breathtaking cliff top views of the majestic Southern Ocean, the intrigue of shipwreck coves along the Great Ocean Road, and what most will call the eighth wonder of the modern world, the “Smelter in the Park”. Integrated within Portland’s beautiful landscape is a 356,000 ton/year aluminum smelter that stands as a symbol of collaboration between nature and industry. Nestled atop a ridge which faces “Sail Rock”, a popular destination of local and visiting fisherman, the smelter is engulfed in a mix of brush and wetland preserves that are home to many of Australia’s feathered and fourlegged natives. Also within its interior you’ll find parks and natural landscapes abundant where man and machines coexist with the native inhabitants."

Jan 1, 2009

By Jilai Xue, Jun Zhu, Yongqiang Liu

"Up-grading silicon feedstock by removing B and metal impurities can improve process efficiency and lower production cost in metallurgical processing for solar cells production. Hydrometallurgical study has been carried out in laboratory through alternative treatments of the metallurgical grade (MG) silicon (-200 mesh) by using hydrogen peroxide, hydrofluoric acid (4 mol/L) and NH4Cl-NH4 F (30:5) solution. The experiments were usually performed under mechanical agitation at 70 ? for 5 h. ICP-AES analysis showed that B content in MG silicon after the hydrometallurgical treatment has reduced by 92.4 %, and Fe, Al, and Ca contents by 98.8 %, 98.0 % and 81 %, respectively. Kinetics of these processes was also studied for better understanding of the effects of silicon powder size, acid concentration, leaching and oxidizing time on the processing chemistry.IntroductionAs one of the most clean and promising new energy, solar energy is used more and more in many countries all over the world, especially in United States, Japan and European Union. Most of industrialized states have made their national photovoltaic plans, which have stimulated further increase in use of solar energy. Photovoltaic Industry is at a high growth rate about 30 % [1-2]. For silicon solar cells to remain the mainstay for the photovoltaic industry it is necessary to develop a low-cost solar grade silicon feedstock [3]. At the same time, the availability of the currently M-G silicon from the semiconductor industries becomes limited [4]. With the advantages of low cost and low energy consumption, metallurgical routes to product solar–grade silicon get more attention [5]. These routes mainly include pickling, slagging, vacuum processing and directional solidification, etc [6]. Among them the most important processing step is the directional solidification, but it still can not satisfy the industrial demand for removing B. Removing B from Si remains as one of the most difficult and important processes in making M-G silicon [7]."

Jan 1, 2012

Halide media are considered as suitable alternatives to cyanide for extracting gold and have received much attention lately. The extraction of gold by iodide-iodine mixture has been patented and briefly studied without much attention given to the fundamental aspects of this process. This paper reports recent studies on the kinetics of gold extraction in iodide media, using hypochlorite, iodine and hydrogen peroxide oxidants. The kinetics of dissolution was found to be dependent on the solution pH, reagent concentration and most importantly the iodide- oxidant molar ratio. Without proper control, the gold surface can be passivated due to the formation of solid products. Thermodynamic modelling was carried out to determine the equilibria governing the dissolution process. The formation of AuI solid was also identified as a possible product during the dissolution.

Jan 1, 1992

By N. Pradhan, B. K. Mishra, B. D. Nayak, B. K. Mohapatra, R. K. Mohapatra

"Present study is about use of a group of Iron[Fe(III)] Reducing Bacteria (IRB) to convert the goethite (a-FeOOH) present in the original lateritic Nickel ore to magnetite under an anaerobic condition and subsequently release the bound Co(III) and Ni(II) through leaching. The lateritic Nickel ore contains 0.8% Ni, 0.049% Co, 1.92% Cr, 0.32% Mn and 50.2% Fe. An anaerobic dissimilatory Fe(III) reducing bacterial consortium capable of using acetate as carbon source (electron donor) and lateritic ore as terminal electron acceptor, changes the initial light brown color of the ore to dark brown. The change in color is due to the conversion of goethite to magnetite, which was confirmed by XRD. When the IRB treated sample was subjected to both bioleaching and acid leaching, it shows a greater recovery of Nickel and Cobalt values as compared to untreated original lateritic Ni ore. Further a magnetic separation method was used to separate the magnetic part of the treated lateritic ore and subjected to acid- and bio-leaching for better recovery of Nickel and Cobalt.IntroductionIt has been known that micro-organisms have the potential to reduce metals but more recent observations have shown that a diversity of specialist bacteria and archaea can use such activities to conserve energy for growth under anaerobic conditions [12]. Natural Fe(III) oxides are high in surface area and are reactive [1]. Fe (III) oxides adsorb a wide range of metal cations and anions by complexation to surface hydroxyl groups [17], and function as the primary redox buffering solid phase in many sediments and subsurface materials [5].Recently a number of bacteria have been isolated based on their ability to use metal ions, including Fe(III), as electron acceptor under anaerobic conditions. These are capable of producing energy by coupling the oxidation of organic compounds to reduction of Fe(III). Iron[Fe(III)]-Reducing Bacteria (IRB) have been isolated and identified from a wide variety of environments including freshwater and marine aquatic sediments and submerged soil [8]. The biogeochemical cycle of iron is linked to those of the trace metals, as many trace metals coassociate with Fe(III) oxides or reduced iron phases (e.g., magnetite, siderite, or iron sulfide). IRB can utilize Fe(III) oxides as terminal electron acceptors for respiration [18]; thereby reducing all or a fraction of the solid. The reductive portion of the iron biogeochemical cycle in non-phototropic environments (e.g., sediments and subsurface materials) is driven by the direct enzymatic reduction of Fe(III) oxides to Fe(II) by dissimilatory iron reducing bacteria [13,14]."

Jan 1, 2009

By Kazue Moriya

At the 1980 TMS-AIME world symposium, Dr. Davey mentioned that the traditional lead blast furnace is now being challenged by direct smelting processes. In the copper smelting field both the blast furnace and reverberatory furnace are also disappearing in favour of direct smelting processes such as Outokumpu flash smelting, Mitsubishi continuous smelting, Noranda furnace, Inco furnace and so on. Those new processes all have the following in common: (1) High degree of mechanization (2) Metallurgical reactions carried out in closed vessels (3) Application of oxygen and/or oxygen enriched air (4) Minimization of handling materials and gaseous volume (5) Minimum energy requirements (6) Removal of workers from near the furnace (7) Reduction of emissions of harmful gas to meet environmental regulations. (8) Improvement to the work place environment to avoid occupational hygiene hazards. Direct and continuous smelting of powdered concentrate in one vessel was a romance of the metallurgist since early times. However as mentioned above, in the copper field this objective is being achieved in practice. The industry however can&apos;t deny that the serious and severe regulation of environmental pollution in every country was the prime motive for the modernization of smelters. In early days, to meet regulations, it was anticipated that many economic difficulties such as higher capital and energy costs and extravagant use of resources and waste disposal would be the result. "Turn a misfortune into a blessing" is an old saying which reveals the current thinking and reacent developments in the nonferrous industries. In the last ten years in the lead smelting field, about two decades later than copper, commercial scale smelting using new furnance technology has started. The KIVCET process and QSL process, which is flash smelting and bath smelting respectively, are becoming major competitors. They will be sure to upgrade their processes to remain economically and environmentally viable in the comming decade.

Jan 1, 1990

By H. D. Freeman

The occurrence of gold in refractory gold ores varies widely and affects the recovery process. The determination of gold and the composition of the associated minerals are important in selecting an appropriate processing scheme. However, locating the gold in an ore sample is a difficult task which requires perseverance, luck, and experience. Our experience has led to the development of a relatively fast and reliable means of deter-mining the mineralogy of ore samples through analysis combining an energy-dispersive x-ray analyser coupled to a scanning electron microscope (SEM). In some cases, a wave length dispersive spectrometer or microprobe is used to further quantify the various mineral compositions. The SEM/microprobe analysis identifies the source of problems that may arise during the recovery of gold from refractory gold ores.

Jan 1, 1981

By M. J. Adam

The Bureau of Mines is investigating the feasibility of partitioning complex sulfide minerals to simpler sulfide phases by sulfidation reactions. Such partitioning can afford opportunity to improve selective extraction of mineral constituents of value. This report describes research involving sulfidation partitioning of byproduct chalcopyrite concentrates from Missouri lead ore processing, and a Utah chalcopyrite concentrate from Cu ore processing. Small chalcopyrite samples were sulfidized with elemental S in glass capsules sealed after evacuating and backfilling with He, by heating for 1 to 24 h at specific temperatures in the range of 250? to 500? C, extending from below to above the boiling point of S (-4450 C).

Jan 1, 1987

By M. T. Thomas

Sufficient development of the X-Ray Photoelectron Spectroscopy (XPS), the Auger Electron Spectroscopy (AES), and the Secondary Ion Mass pectroscopy (SIMS) has made these instruments ideal for solving problems related to mineral processing -particularly gold ore processing. XPS can determine both the surface composition and chemistry of ores and tailings, and the various phases within either of them. AES can also determine surface composition with the further advantage of having greater spatial resolution so the surface chemistry associated with specific minerals in the ore can be identified. This identification helps to clarify why some minerals pass through a chemical process unaffected, while others can be successfully treated. SIMS has an elemental sensitivity from one to four orders of magnitude greater than XPS or AES which makes it useful for detecting the presence of some elements in very low concentration (parts per million).

Jan 1, 1981

By P. Kerr

Iron segregation is pre-dated by copper and nickel segregation processes for which the experimental methodology and reaction chemistry were established. The accepted reaction sequence for segregation involves the generation of hydrogen chloride, the chloridization and volatilization of the metal chloride, and precipitation of the metal from the metal chloride in the vicinity of carbon. Iron segregation roasting offers a potential extraction solution for processing oxide deposits with complex mineralogy or waste streams such as Minette-type iron deposits, nickel laterites, ilmenite, red mud, electric arc furnace (EAF) dust, mill scale and slag. After subsequent magnetic separation, one is left with a high grade metallic iron powder which can be marketed for powder metallurgy or briquetted to serve as a direct reduced iron (DRI) product. The non-magnetic product is typically concentrated oxides including rutile, alumina, or oxides of V, P, and rare earths, etc. that may be economically recoverable with subsequent processing. While operating conditions vary for different metals, they share the requirements of an elevated operating temperature and a mixture of oxide ore, carbonaceous additive and a chloride additive in varying amounts all in a closed reactor to allow for reducing conditions and contain the volatile chlorides. This process is then followed by some form of physical separation. Testwork performed by the authors shows promising results that may aid in future development of the process. Segregation roasting of iron will likely never displace traditional beneficiation and ironmaking technologies; however, it has great potential in niche markets where traditional technologies have failed or current technologies generate substantial waste.

By Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"In this paper, we describe the current status and research progress on the utilization of typical industrial solid wastes in China. We propose a creative method called “eco-utilizing wastes” with an aim of both integration and increment but without second-time waste and pollution, in terms of the characteristics of typical industrial solid wastes, such as titanium-bearing blast furnace slag, high-silicon iron tailing and boron-enriched slag as well as oil shale.Situation of Typical Industrial Solid Wastes in ChinaThough mineral resources in China are abundant, most of these are low grade ores. Moreover, the distribution of mineral resources is asymmetric, which causes the increase of cost and decrease of the economic benefit. Over-exploitation of mineral resources results in a large number of solid wastes. The accumulation of solid wastes not only means the waste of valuable resources, but also causes environment deterioration. There exist some problems in the current practice of the disposal of industrial solid waste, such as only emphasizing the final results and causing new pollution and waste [1]. So the research and development of a high value-added method has a high practical relevance to our nation. Based on the present status and research progress of industrial solid wastes in China, a creative new idea and method for eco-utilization of solid wastes is proposed in this paper."

Jan 1, 2012

By Miguel Barron

Recently, a new lance design for BOF steelmaking has been proposed in the literature. This lance, in addition to six peripheral inclined supersonic nozzles, contains a vertical centered nozzle whose oxygen flow is independent from the main oxygen supply. The above authors affirm that their lance maximizes the droplet generation without causing spitting. In this work, the performance of a lance with four peripheral nozzles and one vertical centered nozzle is numerically modeled by means of Computational Fluid Dynamics software. Transient two dimensional computer simulations were carried out considering two phases, namely molten steel and gaseous oxygen. Numerical results confirm that bath agitation and droplet generation are enhanced as a result of the vertical centered nozzle, however a proper performance of this lance, related to a conventional one, strongly depends on the Mach number of the oxygen jets and the lance height.

Jan 1, 2008

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro

"Jute fibers have in the past decades being investigated as possible reinforcement of polymer composites. However, information is still needed on the fiber interaction with a polymeric matrix for a complete evaluation of the capacity of load transference inside the composite. The present work investigated the interaction of jute fibers with polyester matrix by means of the critical length assessment through pullout tests. Tensile tests of polyester sockets embedded with different fiber lengths allowed the critical length to be determined and then the interface shear stress to be calculated. A relatively low interfacial strength was found, which indicates a weak adhesion between the ramie fiber and the polyester matrix. The SEM analysis of pulled out fibers corroborates this result.Introduction Natural fiber, mainly those lignocellulosic extracted from plants, have, in the past few decades, attracted the attention not only of scientists but also of industrial technologists of our society interested in their engineering applications. As it is well known, uses of natural fiber in clothes carpets, baskets, ropes and low cost construction roofing has existed from the beginning of our civilization. Today environmental and energy saving issues are motivating research works on new uses of lignocellulosic fibers in polymer composites [1-6]. Moreover, industrial application of lignocellulosic fiber composites are already in technological sectors such the automobile industry, packing and civil construction [7-9].In addition to environmental, economical and social benefits, some lignocellulosic fibers present specific properties that are comparable to those of other synthetic fiber used for polymer composite reinforcement. For instance, the specific strength (GPa.cm3/g) of curaua (1.31), sisal (0.92) and ramie (0.93) fibers, from results obtained with very thin diameters [10] are relatively closer to that of glass fiber E (1.33). Therefore, in principle, it would be technically justified to replace glass fiber, which is more expensive, toxic and represents a problem to the environment [ll], by a strong lignocellulosic fiber. However, serious drawbacks such non-uniform dimensions and heterogeneous properties [6] as well as the tendency to form aggregates during processing and incompatibility with a hydrophobic polymer matrix, reduce the potential of lignocellulosic fiber to be used as composite reinforcement [1-6]. In particular, a low interfacial strength causes a weak adhesion between the hydrophilic fiber and the polymer matrix."

Jan 1, 2011