Search Documents

By Yang Hong-ying, Yu Juan

Electrochemical behavior of natural chalcopyrite in electrolyte solution at pH value of 6.97 was studied by cyclic voltammetry, X-ray photoelectron spectroscopy and electrochemical impedance spectroscopy. The results showed that the electrochemical processes occurred on electrode surface were controlled mainly by the growth of sulfur species at lower applied potentials (<0.35Vvs.SHE), and the oxidative dissolution of sulfur species and the hydroxylation of iron at higher applied potential (>0.45V). The EIS spectra of oxide product layers could be illustrated by the equivalent circuit of Re(QdlRct(QfRf)), and the degree of hydrophilicity for chalcopyrite was higher when the value of charge transfer resistance Rct. was greater. The optimum potential range for the floatation of chalcopyrite in collectorless solution at pH value of 6.97 was between OCP (0.165V) and 0.35V.`

Jan 1, 2015

By Yongxiang Yang, Yanping Xiao, Robert G. Harskamp

"Stricter environmental regulations demand for safer treatment and disposal of incineratior fly ashes. So far no sound technology and processes are available for a sustainable and ecological treatment of the waste incineration ashes, and only partial treatment is practised for temporary and short-term solutions. New processes and technology need to be developed for comprehensive utilization and detoxification of the MSW (Municipal Solid Waste) incinerator residues. The objective of the current research is to better understand the behaviour of the environmental harmful elements during low or high temperature treatment, and to find an optimum route for an efficient processing of the incineration fly ash. In the present study, the fly ashes including boiler ash and ESP (Electrostatic Precipitator) ash sampled from a MSW incinerator were washed with warm water, and the residues were dried and sintered or vitrified at high temperatures. The solutions from ash washing were analysed, and will be treated for salt extraction and purification. The ash residues before and after thermal treatment were also analysed. The results of vitrification and thermal behaviour were compared with those from the ashes without pre-washing. It was found that water pre-washing is an efficient way to remove certain water-dissolvable volatile salts such as chlorides, and thus the secondary emissions during vitrification could be reduced. INTRODUCTION The air pollution control residues from MSW incineration are classified as harzardous waste, including boiler ash, ESP ash and filter cake. The boiler ash is the firstly settled flue dust in the dust-collecting equipment under the boiler, the ESP ash is collected by an electrostatic precipitator in the second step, finally the flue-gas is further cleaned by the wet-scrubbers and residues are accumulated in the filter cake. Both the boiler ash and ESP ash are classified as hazardous materials, harmful to the environment due to the high concentrations of environmental hazardous elements. However, due to the different locations of the ash collection, the boiler ash has different compositions compared to the ESP ash, and is considered less toxic. Fly ash is generally toxic and with low bulk density, and has to be treated before final disposal. The current industrial practice is normally the landfilling after partial detoxification such as cement solidification."

Jan 1, 2008

By Bogidar Mihaylov

A laboratory study was conducted on continuous precipitation of copper, cadmium, mercury and arsenic using thiourea, thioacetamide, sodium sulfide and ammonium sulfide as precipitating agents. Depending on the experimental conditions the metals precipitate with the sulfide donors at different orders and rates. These differences were employed as a basis of several techniques for continuous separation of copper and arsenic, cadmium and arsenic, mercury and copper, and copper, mercury and arsenic. The separation of the metals from industrial waste solutions was also studied. The precipitates obtained were inspected using x-ray diffraction, scanning electron microscope, atomic absorption spectrometer and plasma particle counter.

Jan 1, 1992

By P. Meyers, F. DeSilva, L. Gottlieb

A number of tests looking at lead removal using ion exchange resins of various types from various aqueous streams have been undertaken. The tests focused on strong acid cation (SAC) and weak acid cation 0N AC) resins. It was found that the mechanism of lead removal is partly by lead filtration rather than solely by ion exchange in a large portion of the applications studied. This is not surprising since lead carbonate is essentially insoluble and almost all water supplies contain at least some carbonate alkalinity. Regeneration of lead from exhausted resins containing significant amounts of lead may not be practical in some cases because of the large chemical and waste volumes involved. Since lead, .·along with many other very insoluble metals, is often present as a suspended solid rather than in ionic form, ion exchange is probably not always the best technology for bulk lead removal.

Jan 1, 2000

By Dong-dong Liu, Jian-ping Niu, Qi Liu, Shu-sen Cheng

A numerical model was developed to simulate the three-dimensional heat transfer in the belly and lower shaft region of the blast furnace wall consisting of copper steel composite stave, packing and shell. The temperature distribution of copper steel composite stave without the slag layer or refractory lining was investigated and then compared with the copper stave. The results showed that copper steel composite stave can satisfy the requirement of overheatingfree and had an analogous heat transfer behavior as copper stave but more stable cooling intensity. This model had been validated by the good agreement between the computed and measured temperature in the thermal test.

Jan 1, 2015

By A. P. Paiva

Although the advantages of Solvent Extraction for separation/purification of relatively concentrated solutions are well known in Extractive Metallurgy, its use for the recovery of elements present in low levels only recently has been discussed, with particular attention devoted to precious metals. In this work, the extraction behaviour of Cyanex 471X towards silver, from an acidic chloride medium is reported, the extraction and stripping isotherms and related kinetic features analysed. Results on the selectivity of silver extraction against high contents of iron, copper and lead are discussed. Phosphine sulphide extractants are generally associated with solvation mechanisms: analysis of the extraction pathways along with the possibility of reaching a suitable loading in the organic phase are also presented.

Jan 1, 1993

By Isabela Leao Amaral da Silva, Alice Barreto Bevitori, Frederico Muylaert Margem, Victor Bastos da Silva, Sergio Neves Monteiro, Artur Camposo Pereira

"The jute fiber is one of the most rigid natural lignocellulosic fibers, which has since the last decade been investigated as possible reinforcement for polymeric composites. In the present work, the tensile properties of DGEBA/TETA epoxy composites reinforced with jute fibers with different diameters were investigated. Composites with volume fractions up to 30% of continuous and aligned jute fibers were tensile tested at room temperature to evaluate the ultimate strength, elastic modulus and total strain. For each volume fraction, separated fibers with smaller larger diameters were tested. The results indicated that the tensile properties tend to improve with increasing volume fraction of the thinnest jute fibers. The role played by the fiber/matrix interaction was analyzed by scanning electron microscopy.IntroductionThe interest of this research is to develop composites with epoxy resin matrix reinforced with continuous and aligned jute fibers, for applications in various industries, including construction and automotive industry. Conflicts related to the use of non-renewable forms of energy are increasing the interest to enter the market to replace natural materials, synthetic materials synthetics have a higher power consumption in its manufacture [ 1-4].Therefore, applications of natural lignocellulosic fibers obtained from cellulose-based plants are receiving increased attention as an alternative to replace more environmentally correct nonrecyclable materials, energy intensive and glass fiber composites in [5-6]. The use of composites reinforced with natural fibers is a reflection of the concerns with environmental issues such as pollution caused by waste that is not biodegradable or cannot be incinerated and climate change due to C02 emissions associated with the processes of intensive energy and also motivates this work to develop self-sustaining, since natural fibers generate a source of income, especially in developing countries, where most originate, encouraging the cultivation of non-food agriculture [7-9]. Additionally, it is worth also remembering that these fibers come from renewable sources, in addition to being abundant, inexpensive and have a relevant set of mechanical properties [10]."

Jan 1, 2013

By Hee Dong Jang, Hong Yong Sohn, Miguel Olivas-Martinez

"Tetramethylorthosilicate (TMOS), a precursor of silica nanoparticles, is prepared from the waste silicon sludge, followed by the synthesis of silica nanoparticles from the TMOS by flame spray pyrolysis. A two-dimensional multiphase computational fluid dynamics (CFD) model for the flame spray pyrolysis process (FSP) for the synthesis of silica nanoparticles has been developed. The model incorporates the governing turbulent equations of overall continuity, momentum, energy and species mass transport to represent the gas phase and the population balance model (PBM) to account for the silica nanoparticles. The model has been validated with experimental data in terms of gas temperature and average particle size. Introduction Silica (SiO2) nanoparticles are used in various industrial applications, such as catalyst, pigments, thin film substrates, electronic and thermal insulators, and humidity sensors [1]. They are also used as additives in plastics and rubbers to improve the mechanical properties of elastomers, and in liquid systems to improve their suspension behavior. These applications rely on the particle morphology, average particle size, particle size distribution, and phase composition [2]. Silica nanoparticles can be synthesized by wet chemical processes such as sol-gel methods and high-temperature processes such as flame spray pyrolysis (FSP). The FSP process provides a unique control of particle size and crystalline structure and it can also produce high-purity, thermally stable particles continuously with minimal further treatments. The sizes of the flame- made particles range from a few to several hundred nanometers, depending on the operating conditions [1]. The synthesis of silica nanoparticles from organic compounds that contain silicon by the FSP process is of interest because it generates no harmful by-products [1, 3]. Several compounds such as tetraethylorthosilicate (TEOS) and tetramethylorthosilicate (TMOS) can be used to synthesize silica nanoparticles, but most such compounds are expensive. Thus, it is desirable to prepare the precursor compounds from waste materials. In the present study, TEOS and TMOS synthesized from silicon sludge were used as precursors of silica nanoparticles [4]."

Jan 1, 2008

By F. Michael Hosking

Modeling of a furnace brazing process is described. The computational tools predict the thermal response of loaded hardware in a hydrogen brazing furnace to programmed furnace profiles. Experiments were conducted to validate the model and resolve computational uncertainties. The results from selected furnace simulations and measured thermal events were compared. Critical boundary conditions that affect materials and processing response to the furnace environment were determined. "Global" and local issues (i.e., at the furnace/hardware and joint levels, respectively) are discussed. The ability to accurately simulate and control furnace conditions is examined.

Jan 1, 1998

"Hematite pellets were electro-deoxidized to iron in molten sodium hydroxide to produce iron containing about 10-wt % oxygen. The anodic reaction was the evolution of oxygen on an inert nickel anode. Before the electrochemical reaction, there is a reaction between sodium hydroxide and ferric oxide to form sodium ferrite and, in order to compensate for the reduction in sodium oxide content, 1 wt % sodium oxide is added to the melt. In a laboratory cell, the cell voltage was 1.7 V with a current density of 5000 A m-2, a current efficiency of 90% and an energy consumption of 2.8 kWh kg-1.Introduction The iron and steel industry contributes about 2.3 bn tonnes/annum of the carbon dioxide to the atmosphere, which is about 10% of the total, and some believe that, in order to prevent a catastrophic rise in the earth’s temperature, carbon dioxide emissions must be reduced by 50% come 2050. However, by 2050, it is likely that the iron and steel industry would have grown significantly so that the production may have risen to 2 or 3 bn tonnes/year so in order to meet the 50 % reduction on today’s figure, the carbon dioxide may have to be reduced to 25% or less, which is a very demanding requirement. There are probably three ways of reducing the carbon dioxide output:1. By capture and sequestration, but this may be technically very demanding.2. Reduction using hydrogen in place of carbon."

Jan 1, 2009

By P. Wieser, D. Feke

"Priming of filters with small pores is influenced by the surface tension of the liquid metal and may be complicated by freezing • Freezing followed by melting has been observed experimentally. This process has been modeled on the basis of one dimensional heat flow by radiation to the filter and by conduction in the metal. Also considered are super-heat of the metal and the initial filter temperature. The results of the model provide useful guidelines for the application of filters. IntroductionFiltration has been recognized as a valuable method of refining by removing suspended phases from liquid metals or alloys. Woven fiberglass type fabrics and wire screens were used initially in the aluminum industry. With the introduction of the ceramic filters that exhibit improved inertness and refractoryness, filtration has been introduced to higher melting alloys including cast irons, superalloys, stainless steels, as well as low and medium carbon low alloy steels. A considerable literature is delveloping rapidly on the progress in applications and the advances in understanding the mechanisms and effectiveness of filtration processes (1-8).With the use of filtration for different alloy systems for the production of cast to shape parts a bewildering variety of gating system modifications has been developed (Figure 1) to accommodate the installation of filters in the mold. The modifications have two principal purposes: 1) the runner expansion is intended to compensate for the resistance to flow due to the filter and that of the captured inclusions, and 2) the metal reservoir upstream of the filter, provides a temporary by-pass which permits metal to flow across the filter and heat it until priming can be accomplished. priming of.filters by low and medium carbon steel is readily accomplished but, compared to such alloys as cast iron or 19 Cr-9Ni stainless steel, requires greater precautions to avoid failure to prime by excessive freezing on or inside the filter pores. This problem is further examined below:"

Jan 1, 1986

By M. S. Lee

A cold model study on the effects of various operating conditions on the dispersed-phase holdup in a liquid-liquid emulsion generated by bottom gas injection has been performed using water and kerosene. Dimensional analysis was used to correlate the holdup with the operating conditions and the sampling locations. The holdup increased with gas velocity, and decreased with axial and radial distances. The radial distribution of holdup follows a Gaussian function. The holdup increased with increasing ratio of the heavy phase to light phase volumes and decreased with the total height of the heavy phase. The combined effects of various operating conditions can be represented by the Froude number. The variation of the holdup within the plume was correlated by a single equation involving a set of dimensionless numbers.

Jan 1, 1995

By Adegbenjo Adewale Oladapo, Ibitoye Simeon Ademola, Ladiipo Olufemi Akinbiyi, Adegbola Adekunle Amos, Adeboje Taiwo Bode, Raji Fatai Olasunkanmi

The combined effects of the addition of Silicon (Si) as alloying element and low temperature annealing on the tensile properties of 70/30 brass with Nickel (Ni) and Iron (Fe) contaminants is investigated in this paper. Melts of cartridge brass were made to which 0, 0.5, 1, 2, 3 and 4 wt % of Si was added. These were sand cast into rods of 600 mm by 10 mm diameter and were thereafter machined into standard tensile test samples. Some of these samples were annealed in a muffle furnace at temperatures of 250, 300, 350, 400 and 450 oC respectively and the others were used as control. Subsequently, all the heat treated and non heat treated samples were subjected to tensile tests on a Hounsfield Extensometer and the load – extension plots retrieved were analyzed. Microstructural characterizations of the samples were carried out using Accu-Scope Optical Microscope. The results showed that cartridge brasses subjected to alloying and annealing treatments had improved tensile and yield strengths. However, the tensile properties were increased and maintained within acceptable limits at stress relieve annealing temperatures.

Jan 1, 2015

By Yong Zhao, Yan-hui Sun

Behaviors and evolutions of MgO·Al2O3 in non-oriented silicon steel during calcium treatment were investigated by thermodynamic calculations and high-temperature experiments. MgO·Al2O3 inclusions were the main type of inclusions before calcium treatment, which is also confirmed by the stability diagram of MgO/MgO·Al2O3/Al2O3 from thermodynamic calculations. After calcium treatment, the majority of original MgO·Al2O3 inclusions were mainly modified to CaO-MgO-Al2O3 system inclusions, this would be beneficial to improve castability and product quality of silicon steel. But there was no modification happening to some MgO·Al2O3 spinels which were directly surrounded by CaS inclusions. The content of Al2O3 occasionally existed a sudden increase besides a common decrease in the product layer of CaO·MgO·Al2O3. Then the evolution mechanisms of MgO·Al2O3 inclusions were proposed in present work. Thus, Al/Mg atom ratio had a significant influence on the modification of MgO·Al2O3 spinel.

Jan 1, 2016

By Cleusa Cristina Bueno Martha de Souza

Hydrometallurgical techniques for processing metals are becoming an efficient method for recovering metals. Although batteries&apos; manufacturers have got rid of mercury content, some efforts have been made for recovering other metals enclosed in the battery formula. This paper discusses the bench scale experiments in the purification process of leached solutions from alkaline spent batteries. After leaching process using sulfuric acid as leachant, the solutions containing Fe, Cd, Pb, MIl, Zn and K were neutralized to precipitate iron hydroxide. In a second step, the purification experiments were carried out with excess of zinc dust to try to remove Cd while Mn and Zn still remain in the solution to be recovered in an electrolysis stage. The purification experiments procedures were conducted at different temperatures and times to find out properly conditions from the viewpoint of metals removal After filtration the solutions were submitted to chemical analysis to certify the metals content extracted.

Jan 1, 2001

By P. Louis

Gécamines is the world largest cobalt producer with about 60 % of the Western World production. During the last ten years, its annual production varied from 5,400 to 14,600 t/year. The actual cobalt production capacity of Gécarnines is 18,000 t/year and could be increased in the near future if necessary. Cobalt is presently produced at the Shituru plant by an old in-pulp electrolysis process and in Luilu, by electrolysis of a clear weakly acidic solution. The Shituru Cobalt quality is lower than the Luilu one. For that reason, part of the Shituru Cobalt is fire refined and cast into granules. Large efforts have been succesfully accomplished to improve the cobalt quality. This has been made possible by a better knowledge of the purification processes and of the electrolysis parameters.

Jan 1, 1988

By Mark Jolly

"Over the last ten years or so many man hours have been dedicated to developing methods for simulating shape casting processes. The majority of the methods developed have been devised by a combination of computer, mathematics and materials specialists often with limited knowledge of foundries and foundrymen. As a result of this it would appear that although there are many software packages for the foundryman to use there still exist fundamental misunderstandings as to their usefulness and suitability within the foundry.The paper aims to identify how well current software packages perform. The relationships between physical phenomena, practical defects and software capabilities are presented. Some discussion of the use of criteria functions is also presented. Finally issues arising from the postprocessing of results are discussed as the presentation of the results to the lay-person in simulation techniques is possibly one of the most important aspects in influencing the adoption of this type of software in the foundry community."

Jan 1, 1999

By T. W. Gonzales

The BHP San Manuel Smelter operates an Outokumpu Oy flash furnace, conventional Peirce-Smith converters, anode casting facilities, and two double contact sulfuric acid plants. The flash furnace was commissioned in July 1988 and since then, the smelting capacity has been continuously increased to 30% above design. The converter operation was challenged to process larger amounts of matte with existing capacity. Utilization of industrial technological improvements and people technology transformed the Converter Department from a constraint to easily accommodate the new demonstrated flash furnace capacity. This technology also increased secondary consumption, converter campaign life, and reduced operating costs. This paper will describe the important Converter Department achievements in the past five years.

Jan 1, 1999

By C. Lupi

Zinc impure solutions as spent electrolytes, leach liquors coming from aqueous treatment of both minerals and solid waste, need to be purified before undergoing the treatment to obtain the final product. Solvent extraction is one of the most selective operations particularly when many metallic ions are present in solution. Zinc pure solutions are frequently obtained using DZEHPA as extractant. In this work an investigation on zinc extraction effectiveness of naftenic acid was carried out. After determining the best diluent and the optimal extractant concentration, the partition coefficient was determined as a function of temperature, equilibrium pH and zinc concentration. Finally same batch tests to determine the equilibrium curves at room temperature on exhausted electrolyte coming from zinc cell were carried out by using naftenic acid, D2EHPA and TBP. The pH giving, for each extractant, the best extraction yield was selected in order to compare the equilibrium curves. Experimental results show that all the examined extractants are very effective in zinc extraction if the process conditions are appropriately selected. In order to avoid an impure solution pre- treatment and to obtain the maximum ertraction yield the appropriate solvent can be chosen.

Jan 1, 1998

By P. C. A. Maia, J Alexandre, F. A. J. Saboya, A. R. G. Azevedo, G. C. Xavier

"This work shows the characterization of clay and the granite waste by-product from the sawing process of the granitic blocks, used as raw material for brick ceramic. Besides, shows the degradation of the ceramic material obtained with different by-product contents in the waste after lab test degradation, is investigated. The clay is obtained from mine use areas of ceramic industry in Campos-RI and the waste is originating from of the area of Cachoeiro-ES, an important center of decorative stone in Brazil. The mixes were made by the addition of 0% up to 10% of the waste in the raw material. After drying and firing up to 900°C, obtained prismatic pieces were considered intact. Physico-mechanical properties were obtained from wet and drying tests in laboratory considering 50 and 150 cycles. The results showed that the use of powder byproduct has a considerably influence on the weathering and strength of the material.IntroductionThe ornamental rocks and coating defines the most promising areas of business in the mineral sector [l]. In this context, the Espirito Santo appears as the main Brazilian state in production and export of ornamental rocks, representing 47% of national production [2] which in tum is one of the economic sectors most representative of this State, due of its transport logistics and port vocation that facilitates the export of such products.It is estimated that the state of Espirito Santo there are approximately 1,200 companies dedicated to the activities of ornamental rock by providing 20,000 direct jobs [ 1]. These mobilize support activities, such as companies that provide machinery, equipment and supplies for industries, including service providers for maintenance.However, the production of rocks produces about 15,000 tons of granite waste/month [3] only in the municipality of Cachoeiro ltapemirim-ES. This is justified by the presence of more than 500 extraction industries, cutting and processing of stone, with about 900 looms, waste generators.According to [4], there is great potential for the use of granite waste in red ceramics introduced for the manufacture of bricks, blocks structural ceramics. and other ceramic products, especially when evaluated on exposure to weathering."

Jan 1, 2014