Search Documents

By N. Moelans

A method using an ex-situ electrochemical measurement device was developed to determine the oxygen potential of non-ferrous metallurgical slags. The electrochemical cell consists of the molten slag sample, an inert Ir electrode, a stabilized Zr02 solid electrolyte and a NiINiO reference electrode. Different slags from non-ferrous pyrometallurgical processes were analysed at 1100 and 1200°C and pO2 values between 10-3 and 10.12 bar were obtained. The measurements were evaluated with? thermodynamic calculations and using processing considerations. It was found that the reproducibility and stability of the measurement was significantly improved by shielding the molten slag from the atmosphere by a thin layer of carbon, especially for slags with a low oxygen potential.

Jan 1, 2003

By Takeshi Yoshikawa, Kazuki Morita, Yuichi Kato

"A composite composed of carbon fiber and a Cu-Si alloy is a promising candidate for next generation brake disc materials used in high-speed trains. The composite can be prepared by vacuum infiltration of the Cu-Si alloy into the fibrous carbon matrix. The activity of Si in the alloy plays an important role in controlling the formation of SiC; this formation is attributed to the reaction between the Si in the alloy and the carbon fiber during the infiltration process. Because Fe has strong affinity with Si, the addition of Fe is expected to decrease the activity of Si in the alloy. In the present work, the variation in the activity of Si in the alloy with the addition of Fe has been investigated by equilibrating a Cu-Fe-Si alloy with solid SiO2 and graphite under controlled CO partial pressure. The first-order and second-order interaction parameter of Fe on Si in molten Cu was determined to be -16 and 160, respectively. The negative value of the first-order interaction parameter clarified the addition of Fe to the Cu-Si alloy is effective in decreasing the activity of Si in the alloy.IntroductionIron-based materials have been commonly used for brake discs in high-speed trains. It becomes critical for brake disc materials to withstand high thermal loads with an increase in the maximum speed of high-speed trains. The fabrication of high heat-resistant, light-weight brake disc materials is then crucial for their use in next-generation high-speed trains. Carbon fiber is known to be a light-weight, high-strength material, and is considered to be a promising matrix material for use in brake discs. The Cu-Si alloy exhibits high thermal conductivity. The composite in which the Cu-Si alloy is added to the carbon fiber matrix is expected to be a high performance material for brake discs. The composite can be prepared by the infiltration of the Cu-Si alloy into the carbon fiber matrix at a temperature higher than 1700 K."

Jan 1, 2012

By José Sancho, Julia Ayala, Purificación García, Begoña Fernández

"Electrofilter dust, a residue generated in the last stage of the Bayer process in the hydroxide aluminum calcination, was characterized to evaluate the alumina that was potentially extractable with sulfuric acid. The process studied aims to produce aluminum sulfate for water coagulant uses, taking advantage of the residues that accumulate in large quantities in the proximity of plants with difficult recycling for storage. Acid leaching is carried out at different concentrations of sulfuric acid, at different temperatures, pulp densities, and times, to dissolve gibbsite and transition aluminas. The result is an aluminum sulfate solution without iron and with commercial specifications.IntroductionElectrofilter dust is a residue generated in the last stage of the Bayer Process [1] in the hydroxide aluminium calcination. The residue is a mixture of alumina and hydrates which have not completed their calcination process.Electrofilter dust, composed by alpha alumina, gibbsite and transition aluminas [2] can be leached in an acid medium by putting most of the aluminium in solution; the remaining residue should be mainly andisolved alpha alumina. In many hydrometallurgical processes, sulphuric acid has been selected as the cheapest and the most effective leachant [3,4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15]The aim of this study is to determine the effect of temperature, acid concentration and pulp density on the sulphuric acid leaching of electrofilter fines for aluminium dissolution, in order to produce aluminium sulphate for water coagulant uses. This will provide a commercial product and at the same time eliminate the environmental problem created as a result of the storage of large quantities of electrofilter fines in the vicinity of the Bayer plant."

Jan 1, 2008

By Paykan Safe

Computational Fluid Dynamic (CFD) modeling provides a powerful tool to assist with the design of ventilation and fume control systems in smelters and other high temperature metallurgical facilities. For this paper, this tool has been used to analyze the off-gas flow patterns exiting the mouth of a Peirce-Smith converter into a water-cooled hood and drop out box. The effects of various process and physical plant design parameters on process gas and fume capture and potential build up on the converter hoods was examined, and the optimum design and operating parameters were determined.

Jan 1, 2000

By E. A. Trillo, L. E. Murr, R. D. Flores, J. C. McClure, B. M. Nowak

Complex vortex and swirl-like solid-state flow phenomena have been observed in the residual microstructures characterizing the friction-stir welding (FSW) of copper to 6061 aluminum; 2024 aluminum to 6061aluminum,2024 aluminum to 1100 aluminum, 2024 aluminum to 7039 aluminum and 2024 aluminum to 2195 aluminum. These flow phenomena are characterized by intercalation lamellae composed of dynamically recrystallized grain structures of the dissimilar metals which provide a super-plastic-like mechanism for the FSW flow in the solid state; there is no melting and temperatures at the weld center do not exceed about 0.8 TM (where TM is the absolute melting temperature (K)). In experiments to be described and illustrated, optical or light metallography (LM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques are utilized in examining residual FSW microstructures corresponding to tool rotation (stirring) speeds ranging from 400 to 1200 rpm, and traverse (or actual welding) speeds of 1 to 2 mrn/s.

Jan 1, 1999

By Roderick 1. L. Guthrie, Mei Li

"A mathematical model was developed to study the role of orifice shape in the detection of inclusions in LiMCA (Liquid Metal .cleanliness Analyzer) system. The fluid flow field within the ESZ was obtained by solving the Navier-Stokes equations. The trajectories of entrained particles were calculated using the equations for motion of particles. A numerical study of the effect of orifice shape on signal shape generated by inclusions passing through orifice showed that the signals in a parabolic orifice are gaussian in shape, while those in a cylindrical orifice are trapezoidal in shape. This signal shape difference needs to be taken into account when performing particle discrimination. Orifice shape influences also pass-through fraction of inclusions. Finally, a study of the orifice shape on critical conditioning currents suggested that as the polynominal coefficient of the parabolic orifice increases, the critical conditioning current, which is also the maximum operating current, decreases dramatically. These critical conditioning currents also increase as the fluid flow velocity within the ESZ increases. IntroductionThe presence of non-metallic inclusions in metals often leads to impaired mechanical properties such as a reduction in fatigue strength, and to processing problems such as tear-offs in deep drawing and increased breakage rates in wire drawing operations. Similarly, inclusions cause a variety of surface defects in rolled or extruded products.Prior to the development of the LiMCA system (1) at McGill University in the early 1980's, it was not possible to measure inclusions, in situ, in liquid metals. Compared with other techniques, such as sedimentation, filtration and metallography, which require considerable amounts of labor and time, the LiMCA method has the advantage of providing not only information on the volume concentration of inclusions, but also on the size distribution of inclusions immediately and quantitatively."

Jan 1, 2001

By Gökhan Demirci, Ishak Karakaya

"Energy consumption in electrolytic magnesium cells is well above the theoretical values. However, the mechanism of the back reaction, the main cause of the current losses, has not been fully understood yet. Magnesium dissolution into the melt is generally regarded as the limiting step for the back reaction. Accordingly, present cell designs are made with priority given to fast magnesium removal from the cell. However, experimental data and modeling results in this study indicate that the limiting step for the back reaction between magnesium and chlorine is the chlorine dissolution into the electrolyte when physical contact between electrolysis products was eliminated. Effects of chlorine bubbles on the current efficiency and the cell potential were investigated. Results show that the extent of back reaction is proportional to the chlorine surface area in contact with the electrolyte per unit time, and the cell potential increases with the amount of chlorine bubbles inside the electrolyte.1. IntroductionMagnesium is less dense than the electrolyte in electrolytic magnesium production. Therefore, both electrode products, magnesium and the chlorine gas, move upwards inside the molten salt electrolyte during electrolysis. The upward motion of electrode products promotes the most important current loss mechanism, the ""back reaction"". Separation of the highly reactive species; liquid magnesium and the chlorine gas in the cell, to prevent their recombination is one of the main concerns in cell designs. The employment of large inter-electrode distance or a separation wall in early cell designs; decreased the extent of recombination, but increased the cell voltage and energy consumption. Recent cell designs, on the other hand, make use of lifting action of chlorine gas [1,2] by utilizing smaller inter electrode distances to separate the magnesium and chlorine gas faster. Although energy consumption was reduced, but more physical interactions between electrode products make electrolytic magnesium cells still highly inefficient when energy consumptions are compared with the theoretical values. Today, the most efficient industrial cells utilizing high purity feed operate at 10.5-11.5 kWh kg-1 Mg [3-5] and it is considerably higher than the theoretically attainable value of about 6.0 kWh kg-1 [6]. This large gap demonstrates the necessity of more research on physics and chemistry of magnesium cell electrolysis."

Jan 1, 2011

By Debbie Marshall

Process water is an important consideration in the development of a nickel laterite project. Depending on the location of the ore body, sufficient fresh water may not be available and it may be necessary to use seawater (or saline groundwater) for ore preparation. This introduces various species, which have major effects on materials of construction and leaching chemistry. This paper summarizes batch testwork completed at the Falconbridge Technology Center. The leaching behaviour of eleven different laterite ore samples were compared using seawater and fresh water. For brevity, six of the eleven samples are reported here-the other five samples showed similar results. Each ore type was leached under identical conditions in both freshwater and seawater and the leaching chemistry compared. The batch test results were confirmed in a continuous pilot plant, and leach kinetics for the two systems were compared. Keywords: high pressure acid leaching, laterites

Jan 1, 2004

By Catherine Cai

A granular sorbent, prepared by gel-coating polyethyleneimine (PEI) on high surface area silica followed by crosslinking with a low-molecular weight diepoxide, has significantly higher uranium capacity, greater salt tolerance, and faster kinetics than the commercial resin Dowex 21K. Though having lower U(VI)/Fe(III) selectivity than Dowex 21K, the gel-coated PEI affords much higher sorptions of both U(VI) and Fe(III) and also their separation by selective stripping with acid.

Jan 1, 1999

By H. Kamarudin

The behaviour of cassiterite-sulphosuccinamate flotation system was examined in the light of zeta potentials measured by micro-electrophoresis method. It was observed that sulphosuccinamate substantially affects the zeta potentials of cassiterite, lowering its i.e.p. to pH 2.5 and indicating a specific adsorption and/or chemical interaction. The optimum concentration for flotation, as seen in micro-flotation tests, was found to be associated with the most effective lowering of the zeta potentials, the optimum pH being 3.0. The effect of cations in the pulp was examined for the presence of ferrous, ferric, aluminium and lead ions. The ions ferric and aluminium were observed to create an intense effect of increasing the potentials to positive side, possibly due to adsorption of cation hydroxy complexes, as indicated by their respective species distribution diagrams.

Jan 1, 1994

By Halvor Dalaker, Pål Tetlie

The decomposition of methane has been studied experimentally in contact with various oxides at elevated temperatures. For each oxide, the temperature at which the cracking starts has been determined. No correlation was found to exist between the temperature for the onset of cracking for a given oxide and the affinity for carbon of the oxide's metallic component. In terms of potential for using methane as a reducing agent, calculations are presented that indicate that the suitability of an oxide for such reduction depends on the desired methane+oxide reaction being more energetically favourable than the methane+methane=ethylene/acetylene reactions.

Jan 1, 2014

By D. Georgiou

Direct sulphuric acid leaching of nickeliferous limonites is the process of choice to recover nickel and cobalt from equatorially located lateritic ores. These ores are rich-in-iron (-45 wt%) existing in the form of goethite enriched with nickel. The merit of this process is due to its high nickel selectivity because of simultaneous iron separation and acid regeneration. Under acid leaching conditions (-250 to 270°C) iron follows an acid dissolution-hydrolytic precipitation path yielding a very low concentration level depending on temperature and acidity of the final leach liquor. The primary precipitation product of iron is hematite which also forms as a scale on reactor internals along with co-existing aluminum. In this paper, an overview of the behaviour of iron solid products under process conditions is made. The evolution of goethite to hematite transformation, as well as the role of iron in reactor scale production, are studied using SEM/EDX characterization techniques.

Jan 1, 1995

By P. Cowx

The carbothermic reduction of zinc oxide rich Electric Arc Furnace baghouse dust in the Tetronics transferred arc plasma furnace to produce a non-toxic slag and a metallic zinc product is described. In particular, the operation of the zinc splash condenser coupled to the plasma furnace is examined and the effect of process variables on zinc recovery is discussed.

Jan 1, 1990

By A. N. Aposhian

The electronics industry generates tin/lead bearing by-products that can be recycled for their metal value. This paper will cover the processes used to recycle these tin/lead bearing byproducts from the plating, circuit-board fabrication and assembly industries. Though these processes are well known to the companies who do the recycling, few outside the industry including the generators of the by-products, understand the processes or needs of the industry. This paper will give a broad overview of these processes, and describe the services provided by this industry. The paper will also touch upon the future of the recycling industry, including the legislative and environmental push for the elimination of lead from electronics.

Jan 1, 2000

By C. Lupi

Electric arc furnace dust generated during the production of steels is regarded as hazardous waste because of the presence of leachable elements such as Cr, Pb, Cd .... Different processes are available according to the management policy chosen by the steelmaker: disposal. recycle and/or recovery. The feasibility of an hydrometallurgical Zn recovery process on fumes generated during the pyrometallurgical treatment of EAF dust has been investigated. The recovery of metallic iron, chromium and nickel as molten metal provides fumes very rich in zinc oxide ( 63.1% ) and poor in zinc ferrite. This secondary dust is still an hazardous waste and represents the raw material for the recovery of Zn and Pb. The waste material is first leached in 1.5 M sulphuric acid at 30°C to provide a Zn, Fe and Mn rich aqueous solution and a Pb and Ca sulphate rich sludge. The iron is eliminated by precipitation because is harmful to the following electrowinning process. The ftltered and purified leached solution is acidified in order to obtain good electrowinning conditions. A pure cathodic deposit of zinc is then produced in an electrolytic cell at laboratory scale.

Jan 1, 1996

By Michael D. Odekirk

The U.S. Bureau of Mines investigated solvent extraction methods for recovering scandium from water leach filtrates of sulfated tantalum tailings. These complex solutions typically contained 20 or more metals in significant quantities. Two commercially available organics, DEHPA and PC-88A, were identified as effective scandium extractants. The two organics were tested in continuous solvent extraction circuits to compare loading and stripping kinetics, recyclability, and general processibility. Results showed that 95 pct of the scandium, greater than 80 pct of the zirconium, and only small amounts of other solubilized metals were extracted. Scandium was stripped directly as a 3.6 pct Sc precipitate when a 3n NaOH liquor was used as the stripping agent. This precipitate was subsequently upgraded to 94 pct ScE3 via a selective HE leach.

Jan 1, 1993

By C. H. Tsau

The intermetallic compounds of Ni-25Al-xFe, x is 20-40 at.%, were prepared by arc melting and drop casting into ingots, and were rapidly solidified into ribbons by melt spinning. The microstructure evolution of these alloys with varied Fe content were examined by the x-ray diffraction, optical microscope, scanning electron microscopy and transmission electron microscopy. The results reveal that two phases, {y'} and {B} phases, are existing in the alloys with low Fe content, and the microstructure changes from the mixture of y' and {B} phases to a single 0' phase when the Fe-content reaches to 40 at.%. Also, the formation of y' phase will be suppressed by rapidly solidified process. For annealing both of the melt-spun and the cast specimens, a disorder 0 phase was revealed in both of the ribbon and the cast ingot of Ni-Al-Fe alloys with higher Fe content. In addition, increasing the increment of iron which substituting nickel in this alloys results in increasing the lattice parameter of both {y'} and{B} phases.

Jan 1, 1992

By J. B. Cocanour

Pioneering work at the U.S. Bureau of Mines (USBM) has produced a personal computer (PC)-based, software-driven video photometric color sensor for real time process control of metallurgical streams. The video photometer is an inexpensive optical sensor which operates in the visual area of the electromagnetic spectrum and collects color information through plastic optical fiber. The red, green, and blue (R/G/B) voltage components of the color video signal are digitized and characterized through software and then presented as the control variable for software-based proportional-integral-differential (PID) control. This sensor has been successfully employed in the control of a laboratory copper electrolytic circuit. With this sensor, copper solutions were analyzed on-line without the need for sample removal, dilution, mixing or reagent addition, thereby allowing for the real time control of the circuit.

Jan 1, 1994

By M. J. Adam

As part of its research programs, the Bureau of Mines is investigating the partitioning of complex sulfide minerals to simpler sulfide phases by sulfidation reactions. Partitioning in this manner can afford opportunity to improve selective extraction of mineral constituents of value. This report describes research involving the sulfidation partitioning of the mineral pentlandite, which is an important source of Ni in primary production. For the laboratory studies, the pentlandite was synthesized in nominally equiatomic proportions of Ni and Fe. Elemental Ni, Fe, and S powders were blended, compacted, and sealed under reduced He pressure in vitreous silica tubes. The tubes were heated under controlled conditions at SOD? C for 24 h. The product was verified by X-ray diffraction and chemical analysis to consist essentially of (Ni,Fe)9S8. Small samples of the (Ni,Fe) S were encapsulated with sulfur in silica tubes at reduced He pressures and heated for 1 to 24 h at specific temperatures between 400? and 600? C, both below and above the boiling point of sulfur (_445° Cl. Reaction rate increased with temperature. Within this temperature range, partitioning to individual Ni and Fe disu1fides proceeded to essential completion according to the reaction

Jan 1, 1988

By Leandro Voisin

A new pyrometallurgical treatment alternative is proposed for cleaning complex copper matte with high content of impurities in the copper smelting process, thus, in a suitable furnace, a given amount of pig iron will be added to the liquid complex matte with a matte grade between 65 and 75 % Cu under reducing condition and will produce three liquid phases of matte, copper-rich alloy and iron-rich alloy. Hence, in this study, firstly, a mass balance calculation was made on the basis of the reported data for the distribution ratios of the components among the three phases to define the optimum condition where most of the arsenic can be fixed in the less valuable liquid iron-rich alloy. By taking advantage of the high concentration of arsenic in the iron-rich alloy, the small volume alloy may be disposed in a yard, while the precious elements may be recovered effectively in the liquid copper-rich alloy and/or in the liquid matte. Secondly, laboratory-scale experiments were conducted to apply the proposed process to the matte produced from the slag-cleaning electrical furnace and the Teniente Converter of the Codelco-Norte smelter. The obtained results indicate that the proposed process for cleaning complex matte is promising.

Jan 1, 2006