Search Documents

By T. S. Piwonka

Modeling the solidification of shaped castings has progressed beyond the initial problem of determining the correct heat and fluid flow relationships which describe the solidifying castings. Today the challenge is to describe second order effects which determine the ultimate quality of the casting. The challenges to the modeling community posed by the needs of today's foundries for models that work are discussed, with some examples of current modeling problems.

Jan 1, 1992

By E. C. L. Cardoso

Hydrocarbon polymers, as PP, made from cheap petrochemical feedstock are important in many branches of industry. However, they have an undesirable influence on the environment and cause problems due to waste deposition and utilization. Polymeric materials composites account for an estimated from 20 to 30% of total volume of solid waste disposed. Thus, there is a tendency to substitute such polymers by those ones that undergo biodegradable processes. Polypropylene (PP) is a commodity, with high melting point, high chemical resistance, low density, with a balance between physical and mechanical properties and easy processing at low cost. Nevertheless, PP shows limitations for some special applications in automotive industry and civil construction. In order to minimize this deficiency, related to rheological behavior of polymer melt, especially referring to viscosity in processing temperature, a 50% mixture with HMSPP (High melt Strength Polypropylene) was used. PP/HMSPP was blended with 10, 15, 30 and 50% of natural (sugarcane bagasse) and synthetic polymers (PHB and PLA) aiming to partially biodegradable materials. The admixtures were subjected to gamma-irradiation at 50, 100, 150 and 200 kGy and then further assessed by mechanical tests in order to evaluate their degradability.

Jan 1, 2015

By Shaik Jeelani, Esperidiana A. B. Moura, Vijaya K. Rangari, Roberta A. Lima, Rene R. Oliveira

This work present the preparation and characterization of biodegradable nanocomposites based on aliphatic-aromatic copolyester (PBAT)/polylatic acid (PLA) blend reinforced by TiO2 nanoparticle. The biodegradable polymeric nanocomposites were prepared by melting extrusion process using a twin-screw extruder machine. The influence of the TiO2 nanoparticle addition on mechanical and thermal properties of PBAT/PLA blend was investigated by tensile and impact tests, SEM, DSC and XRD analysis and the correlation between properties was discussed.

Jan 1, 2015

By Richard D. Hagni

Ore microscopy is a useful technique to detect and study the ore minerals that are associated with sediment-hosted and volcanic-hosted deposits of finely disseminated gold and silver. Ore microscopy can be used to determine the: 1) precious metal-bearing minerals in some ores, 2) associated ore minerals that may form geochemical exploration halos, 3) character of iron sulfide grains, 4) extent of sulfide oxidation, 5) character of oxidized iron minerals, 6) character of original sulfide grains from a study of the hypogene and supergene oxidized ores, 7) relative time of oxidation, 8) character of organic matter, 9) minerals that may consume excessive amounts of cyanide solution, 10) extent of silicification and silica encapsulation, and 11) possibility of salting.

Jan 1, 1987

By Blas Melissari, Stavros A. Argyropoulos

"In this paper a computational approach was employed to estimate the melting of solid spheres immersed in different liquid metals and under different convective conditions. The spheres are made from the same material as the liquid metal. The SIMPLER algorithm was implemented using a three-dimensional system in Cartesian co-ordinates. Experimental validation of the dimensionless correlation was carried out in two fluids with vastly different Prandtl numbers. The dimensionless heat transfer coefficient (Nusselt number) is obtained as a function. of the Reynolds and Prandtl number.IntroductionThere is a paucity of dimensionless convective heat transfer correlations applicable to fluids like liquid metals. The existing correlations cover single Prandtl number metals [l] or at most two different Prandtl number metals [2]. A knowledge of heat transfer rates from particles at high flux levels has become increasingly important to the design of energy transfer systems. Melting of solid particles has been studied extensively as it relates to many engineering and environmental applications, such as materials processing, space applications, water resource and energy conversion. When objects are immersed in a fluid with a temperature higher than their melting point, they melt and produce molten material that then mixes with the surrounding fluid. These objects experience not only size variation but also changes in their shape. This observation is more pronounced when the melting occurs in a forced convective flow.Yuge performed pioneering experimental work on the heat transfer from a sphere to air under mixed convection [3]. He suggested procedures for predicting the Nusselt number. Hieber et al [4] studied the spherical system analytically, but their study was limited to flow with small Reynolds numbers. Many researchers studied the melting dynamics of ice spheres in water at different convective regimes. Aziz et al [5] and Hao et al [6] performed measurements of the heat transfer coefficient in the water system by measuring the melting time of ice spheres in forced convection. Hao et al [7] performed visualization studies of ice spheres melting in water under mixed convection regime. All of this groundbreaking work, however, did not involve the use of liquid metals"

Jan 1, 2004

By S. Ellor

The development of models of INCO's Copper Cliff operations using a computer spreadsheet program is discussed. Empirically developed metallurgical relationships were utilised. The paper concentrates on models of the pyrometallurgical processes but discusses applications such as optimisation of operating parameters, evaluation of feed changes and custom or recycle materials processing. The models were initially developed using a spreadsheet program on a personal computer. The requirements of plant engineers and process operators for significant increases in operating speed led to the transformation of some of the modules. The paper is presented in two parts: 1. The development of the modules using a spreadsheet. 2. The transformation of a module into a high speed tool for process control. The application of the technique to other pyrometallurgical processes is discussed.

Jan 1, 1992

By V. V. Khristenko, V. I. Dubodelov, V. A. Seredenko, B. A. Kyryyevsky, H. V. Seredenko

"During the last decades investigators of many countries shows an increased interest to alloys which are characterized by miscibility gap in a liquid state. It is connected with essential possibilities of control of structurization in such alloys because of the melt at certain temperature parameters is · emulsion with disperse phase inclusions. These ensure essential influence ·on structurizations.The certain inclusions can play a role of lubrication ensuring ""wearless"" process. The sizes of inclusions of this phase can be rather large proportional to sizes of strengthening phase (up to 1000 nm). Other inclusions ensure process of strengthening of a main material. In this case requests to a dispersibility character of distribution and structure of such inclusions are much higher.The multicomponent alloys of system of copper - (Fe - Cr - C)- alloy concern to the number of advanced compositions. The copper alloys with structure of a type of a ""frozen emulsion"" in which strengthening phase· is a chromium pig-iron are characterized by high thermal stability in the extreme operating conditions. The mechanism of inclusions forming is emulsifying of a melt in miscibility gap at temperatures close to temperature of binodal under superimposition of external effects.The main complexity of producing of ware from such alloys is .a providing in their structure of necessary dispersible inclusions uniformly distributed all over the volume. Thanks to a selective action of electromagnetic fields on liquid phases with various electroconductivity relative velocity of phases is created and is regulated the ratio of their ""apparent"" specific gravity is changed. Excitation of pulsing force effects with the certain frequency on interphase surface allow actively to influence on process of a dispersion of a liquid metal medium."

Jan 1, 2000

By W. F. Whittaker

Systematic control of process parameters during electrorefined copper cathode production and final product inspection ensures high quality of produced "ORC brand copper. Since 1986, substantial increases in tankhouse productivity have been achieved by a number of technological and process control changes. This paper reviews the changes implemented to achieve higher productivity and cathode quality.

Jan 1, 1992

By Bingliang Gao, Junli Xu, Michal Korenko, Jinzhao Guan, Liangxing Li, Zhongning Shi, Zhaowen Wang, Aimin Liu

Al-Si alloy, a precursor of solar grade silicon, was prepared by direct electrolysis in cryolite molten salt at 950 oC using high purity silica as material, liquid aluminum as the cathode and high purity graphite as the anode. The electrochemical behavior of Si(IV) ion was investigated using cyclic voltammetry method. The electrolysis products were characterized by XRD, SEM/EDS and ICP. The results indicate that the reduction process of Si(IV) on tungsten electrode is a two-step process and there is about 0.6 V gap between the two steps. The contents of boron and phosphorus in the aluminum-silicon alloy are 3 ppmw and 8 ppmw, which will make the directional solidification purification effectively and reduce the cost of preparation solar grade silicon from metallurgical grade silicon.

Jan 1, 2015

By Rafael Padilla

The recovery of copper from chalcopyrite concentrates by leaching is difficult due to the slow dissolution kinetics of this mineral in most leaching media. However, recovery of copper from sulfidized chalcopyrite (a mixture of CuS and FeS2) by leaching is faster and could be selective depending on the leaching media. In this paper, the result of an investigation on the H2SO4-O2 pressure leaching of sulfidized chalcopyrite is presented. The variables considered in the study were stirring speed, concentration of sulfuric acid, temperature, and partial pressure of oxygen. The experimental data indicated that stirring speed over 500 rpm and sulfuric acid concentration over 0.1 M had very little effect on the leaching rate. An increase in temperature from 90 to 100 ºC increased both copper and iron dissolution; however, further increase to 120 ºC affected negatively the copper dissolution. Oxygen partial pressure was found to be the main variable that controls the copper/iron selectivity of the leaching. An increase in oxygen partial pressure increased significantly the rate of copper dissolution but deteriorated the copper/iron selectivity. The analysis for sulfur of the leaching solid residues indicated that most of the copper sulfide sulfur in the sulfidized concentrate oxidized to elemental sulfur.

Jan 1, 2006

By V. Ramachandran

In view of the increasing environmental regulations that have been promulgated in the last 30 years, non-ferrous smelters and refineries have learnt to handle effectively the process waste streams that need to be bled from the system for impurities' control The cations of concern are copper, lead, zinc, cadmium, mercury, thallium, nickel, silver, sodium and potassium. Anionic species of arsenic and selenium also need to be addressed, Sulfates and chlorides-not a major concern at present-have come under scrutiny in the recent past. The current paper reviews several treatment options with reference to a) types of waste streams processed b )process chemistry c)discharge options and recovery of treated water and d) sludge disposal The long term goal of any smelter and/lor refinery should be to achieve zero liquid discharge from the plant. Methods to obtain zero discharge are discussed.

Jan 1, 2003

By Patrick R. Taylor

A novel method for Chemical Vapor Infiltration (CVI) using plasma technology is proposed, Plasma Enhanced CVI (PE-CVI). Due to the low rates at which CVI is currently performed, the use of plasma as a source of heat may be considered to be a faster and less expensive production method. Precursors fed in the hot region of the plasma gas are completely vaporized and forced by the same flow through a porous preform where it condenses as a new material. In this research, silica and methane where used as precursors to form SiC/on a / graphite felt (preform). To enhance the infiltration process, vacuum was used to increase the flow through the preform. Characterization of infiltrated graphite was perfontied using Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD). A uniform distribution of Sic was observed along the felt with only twenty minutes of infiltration process, yielding a 178% increment in weight.

Jan 1, 1997

By Peter A. Spencer

The metallurgical parameters necessary for the design of a carmercial scale bio-oxidation plant have been determined for the treatment of a refractory arsenopyrite concentrate using a moderately thermophilic bacterial culture. The parameters considered were bio-oxidation rate, culture growth rate, nutrients, solids density, level of bio-oxidation, particle size distribution and oxygen uptake rate. The approach for obtaining the optimum values for these parameters is discussed and values based on results fran batch and continuous testing are given. Estimates of the capital and operating costs for a plant treating the carmercial arsenopyrite concentrate have been calculated fran the test data.

Jan 1, 1990

By E. J. Peuraniemi

Recently commissioned Kennecott-Outokumpu flash converting was developed to replace the approved but environmentally outdated Peirce-Smith -converting to satisfy the globally tightening emission regulations. In the present study, dust formation and reaction mechanisms of two copper mattes with different experimental parameters were studied in lean suspension conditions. Both mattes had very high copper content of approximately 75 wt% and low iron content of 4.5 wt% and 1.2 wt% Fe. A laboratory scale, vertical laminar-flow furnace with a low feeding rate was used to simulate the phenomena taking place in the reaction shaft of a flash converter. Experimental conditions included temperature of 1300 °C with reaction gas oxygen contents of 20 vol%, 50 vol%, and 75 vol%. In the experiments, sieved particle fractions were fed to the furnace and sampled after short reaction time intervals by quenching them into a water film. Collected particles were analysed chemically for their main elements to define their removal rates. Also, optical and scanning electron microscopy with EDS-analyser were applied to determine phenomena occurring during reactions. Kinetics of oxidation as well as ignition of particles are discussed. Changes in particle morphology, size, and composition are reviewed to describe dust formation and reaction mechanisms.

Jan 1, 1999

By David J. Howard, Christine Broadbridge, David C. Paine

"High pressure vapor/solid reactions offer an opportunity for novel synthesis and processing of thin film materials and structures for electronic, optical, and magnetic applications. In this paper we review the use of two high pressure techniques that operate from 25 to 1000 atm (2.5 to 100 MPa) to fabricate thin film oxide structures from Si1-xGex deposited on Si wafers. High pressure synthesis enables temperature-independent control of reaction rates in the oxidation of this multicomponent semiconductor system and hence offers the opportunity to form thennodynamically metastable Si1-xGex<h from the alloy. The thermodynamics of the Si-Ge-0 system are reviewed and a method is described that utilizes selective chemical reduction (via H2 gas) of Si1-xGcx<h to form Ge precipitates in an SiO2 matrix. IntroductionAlloys of Si1-xGex grown epitaxially on Si substrates by chemical vapor deposition (CYD) and molecular beam epitaxy (MBE) have been used to create high performance microelectronic devices1. These devices show improved performance over conventional Si technology because they exploit the Si/Si 1-xGex band-gap discontinuity and take advantage of higher hole mobilities in the Ge containing alloys. While a range of devices based on heteroepitaxial systems have been demonstrated, the Si1_xGex alloys are of particular interest because they are most closely compatable with standard Si device processing. One disadvantage of Si-based materials systems is that they are not typically useful emitters of light. This is important since the use of light (rather than electrons) for transmitting and processing signals into, out of, and within Si-based microelectronics would represent a major technological advance in microelectronics-based communication and computer technologies. Nevertheless, through the use of innovative processing techniques it may be possible to use the Si1_xGex/Si heteroepitaxial system in integrated microelectronic/light-wave technologies."

Jan 1, 1994

By K. B. McTaggart, G. Owusu, P. J. Merrin

"This study was conducted at Hudson Bay Mining and Smelting's zinc electrowinning tankhouse to determine the effects of varying levels of antimony and continuous gelatin addition on current efficiency. The levels of antimony and gelatin were varied from 0.012 to 0.030 mg/l and 0 to 10 mg/ll2 • 31 respectively, based on neutral ZnS04 electrolyte. A non-linear mathematical model relating current efficiency with antimony and gelatin was produced. The optimum operating point for gelatin was 6.5 mg/l. On the other hand the current efficiency increased with decreasing antimony levels. An interaction term between gelatin and antimony is present but is not significant enough to improve the ability of the tankhouse to handle purification upsets in antimony. Individually, the current efficiency was linear (decreasing) with antimony, and parabolic with gelatin concentration. However, at low antimony concentrations stripping of the cathode sheet was difficult. IntroductionThe zinc electrowinning tankhouse at Hudson Bay Mining and Smelting was designed in the 1930's and consists of 120 rows with each row containing ten cells. This system cascades acid from cell to cell In a row, with neutral zinc sulphate solution added to each cell through manually controlled spigots. Animal glue additions are made manually three times per day by operations personnel. The problem with this type of cell design and operation is that feed solution flows and composition can vary from cell to cell and from row to row due to the large number of manual control points. A new system which reduces the number of manual control points was designed and tested to determine if improvement in control of cell conditions would affect current efficiency. This system mixes spent acid, neutral ZnS04 electrolyte and reagents (gelatin, antimony and strontium carbonate) in a separate mix tank, ensuring that all cells receive a uniform feed solution. Gelatin was used in the test system instead of animal glue (which is presently used) because of the poor solubility and supply of industrial animal glue. The study reported here is the first in a series of experiments designed to justify the need to modify the present cascading cell feed system (Figure 1) to the proposed feed system (figure 2)."

Jan 1, 1997

By V. Montenegro

Smelting of copper concentrates in Teniente Converter produces highly oxidized slag, containing from 4 to 10 % Cu and from 15 to 25 % of Fe304. Copper recovery requires magnetite reduction at a level of 5%, determining the degree of cuprous oxide co-reduction and the liberation of copper matte inclusions. The rate of slag reduction is controlled by the mass transfer to the reaction interface. Slag stirring affects the rate of reduction and enhances coalescence of mechanically entrained copper matte inclusions. Slag reduction and sedimentation in the AC electric furnace is a commonly used method of slag cleaning. Utilization of DC electric furnace creates beneficial conditions introducing slag electrolysis additionally to chemical reductions with carbon of coke and electrodes. Application of external magnetic field, interacting with a direct current in an electric furnace, induces magnetohydrodynamic phenomena, such as intensive stirring and electromagnetic buoyancy force acting on inclusions. Laboratory scale research in simulated DC electric furnace with a superimposed magnetic field showed a significant acceleration of the rate of slag reduction and copper removal. Continuous measurement of gas flow and composition allowed for determination of the reduction rate along the time. Application of external magnetic field in the reduction of the industrial slag in a crucible simulated DC electric furnace results such as the increase of the reduction rate from 2 to 3 times, compared with the identical conditions in the AC electric furnace. Interaction of non-homogeneous electric field with crossed permanent magnetic field induces vigorous slag stirring, enhance mass transfer and accelerate the rate of the slag reduction. Additional participations of the slag electrolysis in the magnetite and cuprous oxide reduction as well as the acceleration of the settling of the inclusions by the electromagnetic buoyancy force affect the slag cleaning intensification.

Jan 1, 2003

By Amanda C. Lima, Luiz Augusto H. Terrones, Sergio N. Monteiro

"Fabric from weaved yarns made of jute fibers have been considered as reinforcement for polymeric composites. In particular, these fabrics obtained from discarded sackcloth are presently being investigated as environmentally friendly composites with recycled polyethylene matrix. The objective of the present work was to compare the practical properties and economical aspects of these composites with those of conventional materials such as wooden board and gypsum panels for building application. The comparison showed that, depending on the amount of post-used jute fabric, a cost/benefit analysis favors these composites over the conventional materials.IntroductionThe increasing amount of wastes generated by human activities is becoming a worldwide problem of pollution with growing consequences to the environment. The question on how to dispose these wastes is, therefore, a major global issue. Among the possibilities of it gating the problem, the use of materials with characteristics of being renewable, biodegradable and recyclable is considered an environmentally correct solution. Examples of this type of materials are left over lignocellulosic fiber from coconut husks and sugarcane bagasse [1] that, after the primary extraction of edible pulp and juices, can be recover for industrial application. Nowadays, the main use of these fibers is to reinforce polymeric composites applied as components for building construction and automobile parts [2,3]. In addition to these applications, composites reinforced with residual lignocellulosic fibers may replace conventional furniture and panels made of wood and thus help to reduce deforestation [4].Environmental protection is not the only motivation for recycling natural fiber wastes. In developing regions activities associate with collecting and processing residual fibers provide job opportunities for low-income people. Moreover, if the lignocellulosic fiber is collected as a recyclable waste, it hes the economic advantage of a comparatively cost, which constitutes in a relevant difference as a choice for commercial utilization."

Jan 1, 2008

By Masayuki Kudoh, Kiyotaka Matsuura

"Molten aluminum and nickel cast onto a steel block exothermically react and produce molten nickel monoaluminide, NiAI, which is simultaneously joined to the steel. The heat of the exothermic reaction is transferred to the steel block, and steel near the surface of the block is melted. The depth of the melted steel increases with both the initial temperature of the steel block and the thickness of the produced NiAI. Iron from the melted steel dissolves in the molten NiAI, and an intermetallic compound of NiAI-Fe pseudo-binary system is produced. During solidification of the intermetallic compound, it is strongly joined to the steel. The Ni.Al-Fe intermetallic compound has an excellent resistance to oxidation and corrosion.IntroductionAn intermetallic compound of nickel monoaluminide, NiAl, offers many advantages over conventional superalloys, such as higher melting temperature, lower density, greater specific modulus and higher thermal conductivity [1]. NiAl also exhibits excellent high-temperature oxidation resistance when doped with zirconium or hafnium, and excellent high-temperature corrosion resistance when doped with chromium or yttrium, that are superior to existing high temperature alloys or coating materials [1-4]. On the other hand, NiAI is significantly brittle at temperatures below 600 K [5-7], which is the most sigriificant disadvantage of NiAI. A possible way to overcome the disadvantage and to utilize NiAl as an environmental-resisting high-temperature structural material may be joining of NiAl to a ductile material."

Jan 1, 2000

By V. B. Chernyavsky, Ladokhin S. V.

Equipment and continuous casting technology for the production of small diameter copper rods and tubes are described. Industrial copper wastes, such as scrap and shavings, were used as the charge. An electron-beam installation for rod and tube production includes a crucible with an electromagnetic stirring system and a pouring hole in its bottom, a bottomless mold, .and a special cooling system, which includes an oil and water cooling devices. For the first time in the electron-beam technology, rods of 8 mm and 14 mm diameter mm tubes of 14 mm external diameter and 7 mm internal diameter were produced through continuous casting by pulling them out of the vacuum chamder into the atmosphere with depressurizing the vacuum chamber. The production capacity of a single strand continuous casting machine was 200 mm/tnin for rod casting and 150 mm/min for tube casting.

Jan 1, 2000