Search Documents

By Dennis Dolinar

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

Jan 1, 2007

By Wenbing Guo

Strip pillar mining method is one of the most important techniques for mining subsidence control in China. Mining depth is one of the most important factors that affect subsidence in strip pillar mining method. Six numerical simulation models were set up in this paper to simulate surface subsidence of strip pillar mining at different mining depths. The mining depth in these models ranged from 300 to 800 m. The simulated results were compared and analyzed. The results showed that the subsidence factor of strip pillar mining is related to mining depth. While other things being equal, the subsidence factor of strip pillar mining increases logarithmically with increase in mining depth. Their quantitative relationship was established based on the simulated results.

Jan 1, 2007

By Srinivasulu Tadisetty

The productivity and safety of Indian longwall operations are insignificant because of complex geomechanical conditions. Therefore, the continuous monitoring and forecasting of abnormalities is imperative. Authors developed an innovative real time system and implemented in one of the Indian longwall mines. The real time system was successfully acquired data from underground chock shields and classified the behaviour in real time as per the standard norms. Furthermore, it forecasted the abnormal behaviour of chock shields promptly. The management was implemented appropriate precautionary measures based on real time forecast. Subsequently, the longwall operations were successfully completed with enhanced productivity and safety. This paper discuss the impact of the innovative system on productivity of experimental longwall mine.

Jan 1, 2006

By Hakan Gurgenli

Many coal seams have weak shale immediate roofs that cause ground control problems. Therefore, it is important to know the properties of these shales so that preventive measures can be developed in advance. However, it is sometimes hard to understand this rock type due to its unpredictable behavior. A good example of this situation is found in two shale coal mine roofs located in the Illinois coal basin (Herrin No. 6 seam). Although, these mines are located very close to each other, one of them has many roof falls, whereas the other has no measurable ground control problems. The aim of this paper is to explain why and how one shale roof behaves worse than the other. Laboratory tests, including point load strength index, slake durability index, moisture activity index, weatherability index, water content determination, swelling strain and x-ray diffraction tests were performed to analyze the shale properties. According to these analyses, some useful correlations were found between the engineering properties, moisture-sensitivity indices, and weathering properties. Finally, mine and support design considerations based on the test results were discussed and recommendations to prevent ground control problems were given.

Jan 1, 2006

By John E. Feddock

Retreat mining plays an important role in the coal production within Kentucky and the Appalachian Coal Basin. In Kentucky, the majority of retreat mining is performed in the Eastern coal field. However, since September 2004, Kentucky has suffered four mining fatalities during retreat mining operations, and the coal industry has focused attention on the safety concerns associated with retreat mining practices. The Kentucky Department of Natural Resources (KYDNR) engaged Marshall Miller & Associates, Inc. (MM&A) to conduct a study to ensure that retreat mining is utilizing the best technology currently available and that the current available employee training programs afford maximum safety to miners. MM&A studied 34 coal mines that were conducting active retreat mining operations and represent about one third of all the mines with approved retreat mining plans in Kentucky. This paper summarizes the major research work conducted (Feddock and Ma, 2006) and recommends the practical methods for improving safety during retreat mining operations.

Jan 1, 2006

By John Latilla

Exxaro Mining?s Matla Coal situated in Mpumalanga, South Africa operates two shortwall faces on the No 4 and No 2 seam while the No 5 seam has also been longwalled in the past. Severe strata loading events have lead to a number of serious roof falls on the wall face (facebreaks) resulting in safety threats as well as considerable production losses. In 2002 the No 4 seam shortwall suffered a facebreak restricted mainly to the tailgate side of the mining panel due to a thick, near surface dolerite sill not breaking properly. This was partly due to the premature suspension of longwalling in the overlying No 5 seam. The resultant overloading lead to severe pillar damage and subsequent bord collapse. Surface pre-split blasting was successfully used to relieve the pressure as well as to pre-condition the dolerite above the following two panels. The shortwall on the No 2 seam has experienced mid-face loading due to No 4 seam chain pillars lying over this area and creating a secondary cantilever effect. Pre-split blasting of the solid rock above the No 4 seam pillars has resulted in a significant reduction in the number of facebreaks. The panel layout of the No 2 seam was subsequently changed so that the chain pillars on both the No 4 and No 2 seam are superimposed whereas previously they were offset.

Jan 1, 2007

By Khaled Morsy

The tragic incidents at Sago and Darby coal mines in 2006 pointed out the need for stronger seals to resist the blast effects of violent gob explosions. Mine Safety and Health Administration (MSHA) has published the final rule on Sealing of Abandoned Areas in April 2008. According to the final rule, the mine seals for unmonitored gob areas should withstand an instantaneous pressure of 120 psi. Reinforced concrete (RC) seal is one of the feasible options that can be used to meet the final rule. Concrete is a heterogeneous, cohesive-frictional material and exhibits complex non-linear inelastic behavior under multi-axial state of stress. The increased use of concrete as primary structural material requires the development of sophisticated material models to have an accurate prediction of the material response to a variety of loading situations. The constitutive modeling of concrete has advanced considerably in the past three decades. Choosing a reasonable concrete material model is important in order to obtain an accurate mine seal design. This paper attempts to address the effect of different concrete material models on the response of RC seal subjected to dynamic loads from methane explosion. Three concrete models, from ABAQUS library, were selected to address the effect of non-linear behavior of concrete and damages due to tensile and compressive stresses. In addition, a typical and verified concrete material model was used for conducting 3D finite element models simulating the RC seal by ABAQUS, EXPLICIT ver. 6.6.

Jan 1, 2008

By Hideki Shimando

Periodic weighting and windblast which are caused by the dynamic effects of overburden in a longwall panel significantly affect longwall mining This study describes past experience with wind blast at Miike Colliery, proposes a new loosening system using hydraulic fracturing and moistening, and also discusses strength deterioration in hard-to-collapse roof rocks due to water in order to solve the problems caused by the effects of dynamic roof rocks behavior in a longwall face

Jan 1, 1998

By Dao Hong Quang

This paper describes the numerical analysis of some geotechnical factors influencing the application of Longwall Top Coal Caving (LTCC) method. The study was aimed at comparing the differences in stress distribution in the chain pillars of the face ends and caving mechanism of the top coal in LTCC method between the flat and inclined thick coal seams. The outcomes from this analysis will benefit mine planners in designing the location of roadway development in the next longwall panel. In addition, results from the study will extend the understanding of caving mechanism in top coal section when applying the LTCC method (with the direction of the longwall face is down dip, retreating along strike) in inclined coal seams. The results demonstrate a clear effect of dipping factor on cavability of the top coal and on the stress distribution in the chain pillar of the face ends.

Jan 1, 2008

By Murali Gadde

The immediate floor bed in the Illinois Basin coal mines is often comprised of weak plastic underclay material. Operational and stability problems were encountered in the past due to the low strength characteristics of the underclay floor. Among several indicators of the nature of the floor, Atterberg limits are the most important ones that describe the plasticity behavior of these clayey materials. While several useful and interesting studies were conducted in the past on the Illinois Basin weak floor material, within the knowledge of the authors, a comprehensive database describing the plasticity characteristics of the floor material has never been published. In this paper, a large database comprising over 700 sets of Atterberg limits was put together from 39 inactive and active mines from all the three states covering the Basin. Analysis of this data shows several interesting trends related to the engineering behavior of the floor material. The paper also describes the practical implications of the trends shown by the Atterberg limits.

Jan 1, 2008

By Murali M. Gadde

Welded wire mesh is the most commonly used skin control technique in the United States underground coal mines. Currently, selection of the mesh is based on trial and error rather than any rigorous design methodology. Several factors affect a wire mesh?s performance including the amount of rock material to be supported and how the load is distributed, wire gauge, aperture size, grade of steel, weld strength, bolting pattern and sheet size. Although the best way to choose the mesh is to conduct full-scale physical load tests, because of the limitations on the number of variables that can be considered in such tests and the requirement of an elaborate test set-up, it may not always be possible to use this option. An alternative would be to use numerical modeling to study the load-deformation behavior of a wire mesh. In addition to providing a very detailed stress, strain distribution in the entire mesh, the advantage of this approach is the ease with which parametric studies can be conducted. In this paper it is shown that the load-deformation curves generated by nonlinear numerical models match closely with laboratory derived ones. Then, based on parametric studies, design guidelines are developed to choose the mesh appropriate for different loading conditions. The modeling studies also bring forth the limitations of the current lab studies. For example, under some conditions it was noticed that the small sheet size considered in lab tests would produce higher mesh deformations than a full-size one used in actual practice.

Jan 1, 2006

By P. Gaskell

The paper examines the development of rock movement between a longwall extraction horizon and the surface for a fully caved mining situation. Physical modelling has been used to examine the mechanics of ground movement and the propagation of fractures around the longwall working. The paper discusses dimensional analysis, model construction and measurement technique and data processing of the results into effective graphical forms for further study.

Jan 1, 1988

By Kourosh Shahriar

The occurrence of rock falls in underground coal mines entails detrimental effects as fatal or non-fatal injuries on workers, stoppages in mining operations and breakdown of equipment. In this paper, a risk assessment approach on the basis of a decision analysis trend is employed in order to assess the possibility of and manage roof falls. Risk is then assessed by determination of likelihood of occurrence and the cost of consequences (outcomes). In this regard, collected real roof fall data from Tabas and Kerman coal regions comprising of several underground coal mines are used. It is concluded that the annual accidents due to the roof falls occurrence in the all investigated mines are so high that it is economically feasible to improve the support systems and to implement a suitable educational program as well as an accurate supervision and other elements of safety management.

Jan 1, 2009

By Luis Giraldo

The installation procedure of fully grouted rebar bolts requires that the bolt be pushed through the resin grout until it is fully inserted in the borehole. Resin grout is a highly viscous fluid that is forced to flow through the annulus between the bolt and the borehole as the bolt advances. Variables such as bolt insertion speed, bolt vs. borehole diameter and grout viscosity determine the magnitude of the pressure generated ahead of the bolt tip. Under weak rock conditions, the magnitude of the pressure of bolt insertion is often sufficient to initiate hydraulic fracturing along joints or bedding planes that allow injection of grout into the strata leading to significant loss of bolt encapsulation. The grout pressure front has also been linked to gloving, a bolt installation problem that reduces bolt effectiveness. A series of tests were conducted to characterize the pressure of bolt insertion during bolt installation under various conditions. Analysis of the data shows three distinct stages of pressure build up during bolt installation. Understanding of the mechanisms involved may allow development of strategies for controlling the pressure buildup and its negative impact during roof bolting under weak rock conditions.

Jan 1, 2006

By Anthony Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990?s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine?s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Jan 1, 2007

By Matt Leeming

Several of the underground mines in the UK require a significant number of cable bolts to be installed, remedially, to control worsening roadway conditions. Often the access is limited and the only power source is compressed air. Machines for this duty are generally designed to perform with 100 psi but regularly only half of this is available. This paper seeks to outline the difficulties this situation causes the Rock Bolting Engineer, highlight the technical requirements for a machine of this type to succeed and detail a solution offered by our engineers.

Jan 1, 2007

By S. Paul Singh

Rock burst is one of the most serious mining hazards, adversely affecting the safety, economy and productivity of mines. It is a sudden manifestation of the release of strain energy stored in the rock mass. At present, there is no universally accepted method for predicting the timing of the rock burst. However, if the seismically hazardous regions in mines can be identified before they are exposed to mining then precautionary measures can be planned before the work begins. A study was conducted in Sudbury Nickel Belt and an approach has been proposed to identify rock burst prone workings on the basis of (a) Rock properties and bursting indices (b) In-situ approaches (c) Geological features (d) Mining conditions (e) Observations during mining operations (f) Comparison and analogy with previous case histories of bursting. This approach will facilitate the judicious application of the burst control techniques to seismically hazardous areas.

Jan 1, 2008

By Kot F. v. Unrug

The present combination of coal market prices and reserves, situated in the Central Appalachian Coal Field, is such that mining of smaller coal reserve blocks has become economically attractive. In above drainage deposits, and particularly under mountain ridges, overburden depth can be changing within a wide range. Mines operating in these deposits are usually developing mains along the center of the ridge, with panels projecting from the mains towards the outcrop. Due to changing topography, proximity of the outcrop, and related cover depth, the panels have various lengths. In this reported case study, a mine in Pike County, Kentucky, along the Kentucky ?West Virginia border, difficult ground conditions were encountered, during the development of the mains, under shallow cover, along a narrow mountain ridge. An area having unusual density of vertical joints was encountered. Mining operations were suspended because of roof stability concerns. The ground conditions were studied, analyzed, and control measures proposed to ensure safe passage through the difficult roof area of the mine. The advancement of the mains, through this area of challenging ground conditions, was successfully completed. In this paper, ground conditions are described, with an explanation of the geologic process contributing to their formation. It is interesting to note that similar locations were predicted by the authors, to be encountered in the same mine, based upon the experience gathered from studying conditions of the case described within this paper. When approaching the predicted locations, stability problems appeared to be even more challenging than those encountered previously. Due to changes in the coal market, mine management chose to move the affected mining section to another area of the mine having better coal quality. The advancement of the mains, through the difficult ground conditions, was temporarily postponed. Based upon the analysis of a probable kinematical mechanism of blocks in the mine roof, ground control measures were proposed. The actual application of these principles proved to be appropriate, ensuring safe passage through the difficult ground conditions encountered in the mine.

Jan 1, 2006

By Gang Chen

This paper explores the possibility of using short-term time-dependent plate loading tests to estimate the elastic and viscoelastic parameters of the weak floor strata typically associated with coal seams in Illinois. Plate loading tests with incremental loads, similar to incremental creep experiments, were conducted until the floor failure occurred. For each increment, the load was held constant for a period ranging from 1-4 hours until a constant deformation rate was achieved. The deformation-time data were analyzed for viscoelastic parameters of weak floor strata assuming its behavior to be adequately represented by the standard Burgers model. The analysis required development of mathematical equations for the time-dependent deformation of the standard Burgers material under a three- dimensional state of stress. Time-dependent pillar settlement data at one mine were also analyzed for elastic and viscoelastic parameters of the weak floor strata using the developed equations. These parameters were compared with similar parameters estimated from plate loading tests.

Jan 1, 1990

By David Hill

The Australian underground coal mining industry is increasingly operating in an environment that challenges traditional concepts of coal pillar design, against a background of heightened expectations and demands from other stakeholders with regard to the protection of both natural surface features and burgeoning civil infrastructure. The result is greater possibility of conflict between mine operators, developers and regulatory bodies, with potential for unnecessary sterilisation of Australia?s coal resources and/or escalating surface development / infrastructure protection costs. On the positive side some significant advances have occurred in the general level of understanding of pillar behaviour and stability, both in Australia and overseas. This paper examines some current issues in coal pillar design, focussing particularly on the application and limitations of analytical models of pillar loading. Established methodologies are reviewed and alternative approaches explored, including examples of key geometrical, geological and probabilistic concepts. Practical experiences from the Southern Coalfield of New South Wales (NSW) are examined for the purpose of highlighting critical variables. Finally, some suggestions are made with regard to the direction and opportunities for future research, with particular regard to coal pillar loading, in the interests of all stakeholders.

Jan 1, 2008