Search Documents

By S. L. Bessinger

Introduction In the design and specification of a ventilation system for an underground mine, it is necessary to make reasonably accurate estimates of the pressure losses in the various airways of the mine. These estimates can be made with little difficulty for open airways with simple geometric cross-sections, such as those cut by continuous miners or tunnel-boring machines. The situation is much different on a longwall face, where the airway's complex geometric cross section and the presence in the airway of obstructing equipment having a variety of shapes make it difficult, if not impossible, to estimate pressure loss using traditional methods of calculation. Head losses in mine entries are calculated using Atkinson's Equation. [22H= KPLQ (English) H= KP 3Q (SO (1) 5.2AA] where H = pressure loss, in. of H2O (Pa); K = friction factor, lbf•min2/ft4 (kg/m3); P = perimeter, ft (m); L = airway length, ft (m); Q = airflow quantity, ft3/min (m3/sec); and A = flow cross-sectional area, ft2 (m2) In this equation, the friction factor, K, is an empirical constant that describes the aerodynamic roughness of the airway. Typically, the K-factor for a given airway is determined by measuring the factors H, P, L, Q and A in Equation (1) and calculating K. Tables of friction factors calculated in this way are found in textbooks and handbooks that deal with mine ventilation analysis. Unfortunately, very few K-factors have been measured on longwall faces, and the accuracies of those that have been measured are entirely site specific, because of the wide variety of equipment found on longwalls. The development of a technique for prediction without mine-site measurements of the friction factor for any longwall face, regardless of its configuration, will thus be very useful in the design of ventilation systems for mines in which longwall mining is practiced. Calculation of pressure losses using Atkinson's Equation (1) and empirically determined K-factors provides accurate and useful approximations in cases where the airways have relatively simple cross sections. However, a careful analysis using the principles of fluid mechanics shows that such calculations are based on two assumptions that are not strictly correct when there are obstructions in the airway. The first assumption is that the air velocity distribution in the cross section, particularly around the perimeter, is uniform. This assumption results from the fact that the tabulated K-factor values found in the literature are based on field measurements with uniform conditions. Such uniformity does not exist in longwall airflows. The second common assumption is that the K-factor, and corresponding head loss, is independent of the Reynolds Number (NR) for a given flow. In fact, this assumption is not strictly correct, and is particularly erroneous in the case of irregular protuberances into the airflow, such as those found on a longwall face. The errors arising from the assumptions may be avoided by using K-factors calculated by a newly devised method, described below, which takes into account the fundamental principles of aerodynamic drag analysis. This new technique has two advantages: first, it is flexible enough to model any longwall, regardless of equipment configuration; second, it employs terminology and equations familiar to those who perform mine ventilation analysis, using K-factors, for which ventilation engineers have an intuitive understanding, rather than drag coefficients. To provide guidance for development of a longwall drag model, data were taken on two modern longwalls operating in substantially different conditions. Pressure measurements at Mine B were made with 200-foot (61-m) sections of 1/8-in. (3-mm) diameter plastic tubing, attached to a Dwyer Magnehelic gauge. Pressure drops were measured in 200-foot increments down the face, and summed to give the drop for the entire face length. This technique was found to produce small, repeated errors because of the number of segments required to span the longwall. At Mine A this problem was avoided by using a single, continuous, plastic tube for the entire face length. The psychrometric properties of the air were measured for both Mines A and B. A calibrated, standard vane-anemometer was used to measure the airflow on both faces. Finally, numerous dimensions were measured on both faces, and face profile drawings were obtained to allow detailed evaluation of the face equipment geometry. From this information, accurate evaluations of the average wetted perimeter and average area of the longwall face airways were made. Since the airflow is not confined to inside the powered supports at all points along the face, a quadratically weighted average of the airflows measured at various stations along the face was calculated: [n2Qavg =Qi Ii / It(2)i=1] where [Q, avg = average airflow for analytical purposes, ft3/min (m3/sec); Q= airflow at station i, ft3/min (m3/sec); 1= length of segment represented by Q, ft (m); h= length of longwall face, ft (m): and n= number of quantity measurement stations.] The quadratic weighting scheme was chosen because the

Jan 1, 1992

By LeEtta M. Shaffner, John R. Marks

The Homestake Gold Mine in Lead, South Dakota, commenced operations in 1876. As is the case with old, deep, continuously developing mines, a ventilation improvement is periodically required to maintain acceptable underground environmental conditions. Recent historical improvements at Homestake include a 5.2m diameter air shaft driven in the 1960's and a 2.1 MWR (580 ton) chilled water plant installed in 1978. By 1983, it became apparent that yet another ventilation upgrade would be needed to keep pace with accelerated development in the deepest mining sections. A study was therefore undertaken to project ventilation requirements for the next ten years and to select the method(s) most suitable to meet those requirements. The study called for a two-phase approach in which air flow and air conditioning were carefully balanced. Phase I, the installation of a new 2240 kW surface fan and several underground circuit changes, was completed in 1986. This paper describes Phase 11: the planning, design, installation and initial performance of the air-conditioning portion of the upgrade.

Jan 1, 1989

The dissolution behavior of gold and copper from their elemental states and from Au/Cu alloys in cyanide solutions has been investigated using a rotating disc electrode. The anodic and cathodic reactions were studied separately and the resulting polarization curves were combined to examine the overall dissolution reactions. The dissolution rate of pure gold in the aerated cyanide solutions was inhibited by the anodic passivation on the gold surface, while the dissolution rate of pure copper was found to be mass-transfer-controlled. On the other hand, the dissolution of gold and copper from the alloys was partially controlled by electrochemical reaction and largely by mass transfer.

Jan 1, 1994

In the early days of minimal environmental protection awareness and unreasoning economy development pressures, little attention was paid to growing environmental concerns in Fuxin colliery, especially the air pollution problem due to the long term mining activities. In order to determine air quality concentration levels, a new technique for synthetic assessment of ambient air quality by using the extension of matter-element method is proposed in this paper. The air pollutants data such as Sulphur Dioxide (SO2), Carbon Monoxide (CO), Nitrogen Oxides (NOx), Total Suspended Particulates (TSP), Particulate Matter (PM10), and dustfall collected at four different air quality monitoring stations located in four districts of Fuxin colliery is used. The results obtained indicate that TSP, PM10, dustfall and SO2 are the predominant pollutants. Other pollutants such as CO and NOx are also detected in Fuxin colliery. The air pollution comes mainly from industrial emissions, mining activities and the abandoned gangue stockpiles. Compared to those applied to other mathematical assessment methods, it is demonstrated that the extension of matter-element model is quite appropriate for air quality assessment.

Jan 1, 2006

By Donald M. Keagy

How many times have you said or heard someone say, 'What are you doing right now?" And how many times have you heard the reply, "Breathing air!" Probably never, or at most only a few times in a facetious vein. Breathing air is absolutely necessary to sustain human life, and yet most of us take it completely for granted. Beginning ten to fifteen years ago there was growing concern on the part of the general public that pollution of the air is a threat to man's health and welfare. Concurrently much thought and effort was devoted to the task of defining and resolving the problem of air pollution. In the course of this effort it has become quite clear that our National policy in this regard should be founded upon three basic axioms: (1) Action should not be postponed until emergency conditions make it compulsory; (2) The air cannot be purified after it is polluted, and (3) Air pollution control cannot be accomplished without close cooperation among all levels of government, industry, and the public.

Jan 1, 1967

By Esko O. Nermes

Outokumpu flash smelting of copper concentrates was introduced in 1949 and flash smelting of nickel concentrates in 1959, both at Harjavalta in southwest Finland. The first flash smelter outside Finland was started up in 1956 in Ashio, Japan. Between 1956 and the present about 25 flash smelters for copper, and nickel concentrates have been put into operation in different parts of the world. Outokumpu"s research organization has been highly involved in the development of flash smelting. For example, a direct blister flash smelting process was developed in 1975 and introduced in Glogów, Poland, in 1978, and another has been designed for Zaire. This straight metal process is based on low iron content of the concentrate, which reduces the amount of recycling slag copper. Additionally, the concentrates are rather low in impurities.

Jan 1, 1982

By H. Polat

Relatively large amounts of such hydrocarbons as fuel oils are often needed in flotation of low rank coals. The amount of oil can be decreased considerably by using surfactants as promotors. The reagents which are good candidates as surfactants to promote hydrophobicity can also act as emulsifying and wetting agents. Since the physical and chemical variables influence various sub-processes in different ways, their influence on the performance parameters is complex. The results of laboratory tests are presented to show that the dual role of reagents can be judiciously exploited to increase both the recovery and grade of clean coal. The mode and order of reagent addition is critical in enhancing their efficacy as flotation promotors. The results demonstrate the benefits of proper conditioning of the pulp prior to flotation.

Jan 1, 1997

By O. A. Bascur

In recent years, metal-producing companies have increased their investment in automation and technological innovation, embracing new opportunities to enable transformational change. Transformation to a digital plant can fundamentally revolutionize how industrial complexes operate. The abundant and growing quantity of real-time data and events collected in the grinding and flotation circuits in a mineral processing plant can be used to solve operational issues and optimize plant performance. A grade recovery model is used to identify the best operating conditions in real time. A strategy for increasing the value of instrumentation in current plants is reviewed. An optimal Gaudin size distribution model provides augmented information from traditional sensors to find the optimal grind cut size to reduce metal losses in the flotation circuits. Sensors in flotation circuits enable an estimate of the recovery and determination of the optimal froth depth and aeration using an air hold up flotation model. A strategy of classifying data for online generation of insights to using operational intelligence tools is described. The implementation of a recovery/grind strategy with industrial examples in nonferrous mineral processing is presented.

By G. R. Doubek

Dual Tube Reverse Circulation (DTRC) drilling has been extensively used for collecting groundwater information for the dewatering program at Amax Gold Inc. Sleeper Mine. This paper presents a discuss ion of the types of data which can be collected from DTRC drilling, as well as the effect submergence has on the data. A simple low-cost method of injection testing has been developed using DTRC equipment, allowing quantitative data to be obtained from exploration or test holes. Potential yields can be determined for each drill location, allowing siting and design of production wells to be optimized.

Jan 1, 1992

By George W. Land

For the year 1985, the U.S. coal industry produced 881 million tons of bituminous coal and lignite. Domestic consumption amounted to 814 million tons. The electric utilities consumed 689 million tons, almost 85 percent of total consumption, over 78 percent of production. In May, 1986, the NCA forecast that with moderate growth rate averaging 1.9% per year from 1985 through the year 2000, production could reach 1,176 billion tons and domestic consumption 1079 billion. The estimate for electric utilities indicate 924 million tons for the year of 2000, about the same percentage of production and consumption as now experienced. Before we consider the main topic of this paper, the cost of using high sulfur coal, let us examine the coal use patterns of the last 25 years, the changes in those patterns and consider the reasons for those changes. Table I shows those changes.

Jan 1, 1986

By L. Yan, C. Zhou, M. Reyes

"The MINER Act requires the installation of post-accident, two-way communications and electronic tracking systems for all coal mines. One communication system which can satisfy this requirement is an electrode-based, through-the-earth (TTE) communication system, which sends signal directly through the overburden of a mine. The performance of these types of systems relies on several controlling factors such as earth conductivity, overburden depth, operating frequency, TX/RX antenna length, TX/RX offset, TX/RX orientation angle and TX current. In an effort to estimate attenuation through the earth, NIOSH researchers developed an analytic solution for the electrical field distribution of an electrode-based TTE communication system for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source. The analytic model was then validated using test data measured at an operating coal mine. The validated model can be used to optimize the operating frequency, estimate the required transmitting current, choose appropriate TX/RX orientation, and predict the performance of an electrode-based TTE system at a coal mine. INTRODUCTION One of the requirements of the Mine Improvement and New Emergency Response Act (MINER Act) of 2006 is the installation of post-accident, two-way communications and electronic tracking systems for all underground coal mines. As one of the through-the-earth (TTE) wireless communication methods available for the mining industry, the electrode-based, or linear, TTE systems establish communication by inducing a current within the earth medium by use of a pair of current probes. The resultant current is detected as a voltage by a similar set of distant probes. These probes could be an insulated piece of wire tied to two electrodes grounded at distant ends, or the grounded ends could be rails, roof bolts, or grounded electric rods. The analytical solution developed in a homogenous half-space, for this form for various transmitter/receiver (TX/RX) configurations, will be presented in this paper. The communication signals can be sent either from underground to surface (uplink) or from surface to underground (downlink). In order to achieve a successful communication link, it is necessary to understand the electric fields within the earth so that the appropriate size of transmitting antenna, TX/RX relative orientation, and operating frequency can be chosen. Hill and Wait gave the explicit forms of partial magnetic fields and partial electric fields of electrode-based TTE downlink communication with finite cable length [1]. In prior research, the E-fields of electric line transmitter were obtained for a static TX current [2] [3]. In this paper, the general and explicit forms for electrode-based TTE electric fields are developed and presented. The solutions for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source obtained from these forms are presented. Also, factors that affect the E-field strength at RX are discussed."

Jan 1, 2017

By Johan Bosch, Wout Broere, Minh Ngan Vu

"INTRODUCTION Shield tunnelling is often used in constructing underground infrastructure in cities due to the ability to limit settlements and damage to existing buildings. However, in an urban environment with soft overburden and buildings on pile foundations such as the North-South Line project in Amsterdam, there is a tendency to design the tunnel well below the surface and below the pile tip level in order to reduce interaction between tunnelling process and piles. This results in deep tunnels and deep station boxes. When the tunnels are located close to the surface and above the pile tip level, this would reduce the required depth of the station boxes and the construction cost. Moreover, other benefits of shallow tunnels are the low operational cost in the long-term and shorter traveling time from the surface to the platforms. Still, the tunnels should be constructed in such a manner that existing buildings are not structurally damaged, which results in a minimum required distance between tunnelling process and existing buildings. In this paper, the extent of the area that is influenced by tunnelling will be investigated in order to determine the limit distance from tunnelling to existing foundations without inducing too large building deformation. From analysing empirical data of many shield tunnels, Peck (1969) firstly presented the settlement trough on the surface induced by tunnelling in soft soil as a Gaussian distribution. This is also confirmed by other authors (Cording and Hansmire, 1975; Mair et al., 1993; Ahmed and Iskander, 2010). In this study, the Gaussian curve is used to investigate the ground movement when tunnelling in order to find the effects on existing structures. Based on the results from centrifuge test and empirical data, Mair et al. (1993) showed that the subsurface settlement profile distributes as the Gaussian curve also. The width of settlement trough at the depth z depends on the depth of the tunnel z0 and a coefficient K depending on depth. Other studies by Moh et al. (1996), Grant and Taylor (2000) and Jacobsz (2003) based on Mair et al. (1993) proposed a limited change of K in various kinds of soil."

Jan 1, 2016

By Arthur M. Ribe

In my experience, nothing helps me better to get off to a good start in preparing a paper or a talk than a copious consultation with a comprehensive dictionary. I also feel defining the perimeters of a particular subject is helpful to the listener and reader. Sometimes thus precisely defining even the most common of words is helpful. Our general topic this morning as all of you know is "Transportation of Industrial Minerals." The definition of transportation given by the dictionary which I think is appropriate here is: "Systems and modes of conveyance of persons or goods from place to place." Our preceding panelists have outlined for you the state of the art inso¬far as systems and modes of conveyance from place to place are concerned today via rail, water and motor. My assignment is somewhat different as indicated by my topic, "The Traffic Manager in an Industrial Minerals Operation."

Jan 1, 1969

By Peter N. Loncar

Most miners dream of finding a gold mine sometime during their mining careers, but not very often do such dreams come true. On the tenth day of September, 1962, our dream of finding gold came true when the results of the third drill hole were received. This was undoubtedly one of the most exciting days of our lives. Little did we realize then that this was the beginning of a major discovery destined to became one of the largest gold mines in the country. Discovering and mining gold is not entirely new, however, to Eureka. County a old Lynn Mining District in northeastern Nevada. Since 1900 there has been sporadic activity, mostly consisting of small lode mines and placers. These have produced totally about $300,000; and existence of our orebody would probably have remained unknown had it not been for the United States Geological Survey. The USGS extensively mapped the Roberts Mountain Thrust and published a paper indicating that mineral occurred along this fault and in some places was gold bearing. Utilizing this information, our Newmont Exploration geologists located an area in which: drills were brought in to test their theories. By keeping flexible in our thinning and working, we were able to bring a raw prospect to a producing mine with ore reserves of eleven million tons in a short three-year period.

Jan 1, 1965

By John D. Kalasky

Ventilation is necessary in coal mines to supply fresh air to the working faces for the health, safety, and comfort of the miners, and for the circulation of air to the extent that it will dilute, carry off, and render harmless the noxious or dangerous gases generated. Adequate ventilation depends upon good face control, as well as upon a well designed and properly controlled overall ventilation system. Generally, this includes fans, airways, overcasts, air locks, regulators, checks, and canvas or plastic stoppings near the working places to prevent short circuiting of air, and effective bleeders to maintain a continuous flow away from the working places along the pillar lines at all times and to prevent diffusion of methane back to the pillar line in case of temporary interruptions in ventilation. In the development of a new mine, or the virgin area of an old mine, the main headings should properly be considered a construction project, designed with, only the number of permanently supported (roof) headings required to conduct the necessary air volume to and from the major panels in which mining is conducted by room and pillar or longwall methods. Although subject to hazards from methane quite frequently and requiring constant and careful attention at all times, development of headings has some built in safeguards which make it a less difficult problem in control of methane than exists in pillaring.

Jan 1, 1973

By Martin H. Stanczyk

Under the Solid Waste Disposal Act, the Bureau of Mines initiated several accelerated in-house research programs to develop new and improved methods of proper and economic solid waste disposal. The program being conducted at the Bureau&apos; College Park Metallurgy Research Center is concerned with eliminating the current waste of valuable materials in municipal refuse by developing low-cost methods for reclaiming and recycling the metal and mineral values contained in incinerator residues. Each year the United States must collect and dispose of in some manner or other, about 150 to 200 million tons of municipal solid wastes. The monetary output for this service ranks third among public services, exceeded only by the costs for schools and roads based on population growth projections and materials use patterns, the quantity of refuse generated by the early 1980&apos;s may approach 300 million tons annually. Currant estimates indicate that only 10 to 20 percent of the total municipal refuse generated is disposed of by incineration. If all refuse were properly incinerated the residues would contain more than 11 million tons of iron and nearly a million tons of mixed nonferrous metals including aluminum, copper, lend, zinc, and tin.

Jan 1, 1969

By Aurel Goodwin

I chose the title "Let&apos;s Clear the Air" for this afternoon&apos;s presentation because it has two meanings, the literal and the figurative. Most of you know what MSHA is. Most of you know what MSHA does. And, for the most part, most of you know why. What I hope to accomplish today is to "clear the air" around our health standards, to clarify for you how MSHA views its congressional mandate under Title I Section 101(a)(6), (7), and (9) of the Mine Safety and Health Act. Asbestos, silica, radiation, noise, welding fumes, carbon monoxide, lead, hydrogen sulfide, nitrogen dioxide - the list of physical and chemical hazards encountered in the metal and nonmetal mining industry is as diversified as the industry itself, possibly even more so. In addition, miners are often exposed to several of these health hazards simultaneously.

Jan 1, 1980

By D. K. Adjei, G. Ofori-Sarpong, R. K. Amankwah

"Mercury (Hg) is toxic and has long-term effect on the muscle tissues, the brain and the central nervous system functions due to its bioaccumulation and biotransformation effect. Hg pollution around the world is high and this has attracted much global concern such as the Minamata Convention on Mercury, held in 2013. For several years, mercury has been the chemical of choice for Artisanal and Small-Scale Mining (ASM) gold extraction, accounting for about one-third of the global mercury consumption. A greater percentage of this ends up in the environment through open burning of amalgam, spillage and indiscriminate disposal of waste. To break this wall of mercury pollution, it is very important for the mercury used to be recycled through the use of mercury retort units. This brings into the limelight, the Lantern Retort which tries to synergise the high conductivity of steel and the see-through effect of glass, thus, improving the amalgamation process. A research conducted on improving the original Lantern Retort arrived at an appropriate distillation length of 5.08 cm which was used in redesigning a more efficient retort. The improved Lantern Retort recovered about 98% of the mercury used. INTRODUCTION Artisanal and Small-scale mining (ASM) is an informal mining activities which employ quite simple tools such as pickaxes, sluice boxes, shovels, chisels, metal bars, mattocks and water pumps for mining and processing of gold ores. The artisanal and small-scale mining (ASM) sector has served as source of employment for many people in developing countries including Ghana (Aryee, 2001; Hilson and Potter, 2003; Amankwah and Anim-Sackey, 2004; Amankwah et al., 2010) and has provided a substantial amount of foreign exchange through its activities (Hilson, 2001; Styles et al., 2010). Hentschel et al. in 2003 estimated that about thirteen (13) million people are said to be engaged directly in the small-scale mining activities worldwide. However, an estimated 100 million people are said to depend on this sector for their livelihood mainly in developing countries. In China alone, a projected number between 3 and 15 million people are engaged in artisanal and small-scale mining activities (Hentschel et al., 2003), whilst in Ghana, it is estimated that more than 1,000,000 people are employed directly or indirectly in the artisanal and small-scale mining activities, with 10% being women (Amankwah and Anim-Sackey, 2004; Amankwah and Ofori-Sarpong, 2014). In Ghana, ASM gold production has grown from a low of 2.2% in 1989 to a high of 34% in 2014. This figure is estimated to increase with proper documentation. This indicates that the sector has made significant socioeconomic impact on many individuals and communities as a whole. Notwithstanding the above positive contributions, the sector has also contributed to negative impacts on human, aquatic life and the environment in general due to indiscriminate mercury emission. This ‘pollution wall’ needs to be broken, and several interventions have been put in place including the use of retort units like the lantern retort (Adjei et al., 2014; Amankwah and Ofori-Sarpong, 2014)."

Jan 1, 2017

By Bo Arvidson

SALA MAGNETICS, INC. is now operating a 15 tph continuous high gradient magnetic separator, the SALA-HGMS® Mark III Carousel, as part of a complete mineral processing pilot plant installed at Sala&apos;s Cambridge headquarters. The Mark III can generate a maximum magnetic field of 18 kG making it possible to process even weakly magnetic, finely ground ores and ore tailings on a continuous basis at the performance level achieved in Sala&apos;s cyclic high gradient magnetic separators. Test results on iron ores, clay, and decoppering of molybdenum concentrate will be discussed. Bench scale tests have been performed on all of these materials using the SALA-HGMS® Model 10-15-20 Cyclic Magnetic Separator. A direct correlation may be made between cyclic and carousel results. Sala&apos;s Mark III Carousel high gradient magnetic separator is designed to permit scale-up to machines capable of processing two hundred (200) tons of ore per hour and more.

Jan 1, 1976

By I. Pordea

The materials used for the construction of buildings contain natural radionuclides of the U238 and Th232 series and are ? 50% due to land radioactivity. Another component of natural radioactivity is K40, with ? 40%. The presence of these radiopollutants in the final products (i.e. bricks, concrete) due to body irradiation is by two pathways: external irradiation and internal irradiation. External irradiation is due to gamma radiations emitted by Pb214 (RaB) + Bi214 (RaC) from the U238 series, by Ra228 (Mezothoriu I) + Ac228 (Mezothoriu II) + Tl208 (ThC??) from the Th232 series and by the K40 radionuclide. Internal irradiation is due to inhalation of radon (Rn222) and Rn220 (Tn) plus short life descendents (Po, Pb, Bi), radionuclides which are present in concrete. A fraction from radon present in concrete enters into a house leading to internal irradiation by inhalation. In Romania, the maximum concentration of radon allowed for new buildings is 200 Bq/m3.

Jan 1, 2008