Search Documents

By T. W. Peterson

There are two approaches to developing a minicomputer based application for an industrial grinding circuit. Usually, the control program is coded and compilation-debugged on a large-scale scientific computing system or the minicomputer itself if the machine is available. Final debugging and testing must wait for installation and checkout of the entire minicomputer system. Two immediate disadvantages of this approach are the need to obtain, install and check out the hardware before the final debugging stages of program development can begin, and interference with normal mill operation during such final testing. This work reports on an alternative to the usual procedure. Here both compilation and execution bugs are eliminated from the application program before hardware installation by testing the control program against a reasonable dynamic simulation of the entire process. Thus, software development can be completed before the target mini is installed. Such off-line development requires a reasonably accurate mathematical model for the entire process system as well as a suitable simulation package for communication between the simulated environment and the minicomputer application program. Specific data describing the design configurations and dimensions of the mills, cyclones, sumps, pump characteristics and analog controller configuration were supplied by ANAMAX for a grinding division consisting of a rod mill followed by two ball mills in parallel. This information was used to set up a plausible model structure. Steady state ANAMAX data on particle size analysis at various points in the circuit and corresponding values of flow rates, pump speeds, sump heights and slurry densities were used for model parameterization. The preferred operating control strategy - "best grind at operator-set rod mill feed rate" - was set by ANAMAX. An inferential particle size analysis technique using the cyclone cluster as an on-line particle size sensor was used in a novel control strategy_ to achieve the stated objective. Two disturbances common in the ANAMAX circuits - rod mill scoop pluggage and shut down/start up of one of the ball mills - were studied in detail. This report out- lines the steps in system development and testing and the results obtained.

Jan 1, 1974

By E Marambio, R Brändle, G Fischer, G von Rickenbach, M Fuentealba, L Burgos, R Luis Fonseca

In underground excavations, under high stress conditions, ground support systems must provide safe and effective response to dynamic events. These systems must be capable to resist dynamic impacts and yielding during the loading process. In this context dynamic testing of the reinforcement and retaining elements that compose the ground support system are required to study and improve the behaviour of these elements under dynamic load events. During the last years, Geobrugg has been working on the improvement of retaining products by testing them in a large-scale impact test facility located at Walenstadt, Switzerland. The test facility is composed of a double level platform with a square-shaped pyramidal trunk geometry, in the upper level housing a loading mass that drop from a height up to 5m. The loading mass is guided by one central steel pipe, and the impact occurs in the sample to be tested located at the lower level in a slab with an area of 3.6m × 3.6m where the ground support system is installed. During the last years, this innovative facility has been used to test several configurations of ground support systems. The results of these tests have enabled to improve the understating of the behaviour of ground support systems under dynamic loads. In this manuscript, the back analysis through numerical methods (central difference and Newmark’s method) of a ground support system tested with a double dynamic impact in 2019 is presented.

Apr 26, 2022

By C. L. Lin

A PC image-based, on-line instrument for the measurement of coarse particle size on a conveyor belt is under development. Both the hardware and software required to implement such a system are discussed, including the interface for the special image acquisition hardware. The system concept is given with examples to illustrate the step-by-step procedure for the implementation of image-processing algorithms.

Jan 1, 1992

By V. Nasri, P. Jarast, M. Bakhshi

The Montreal metro Blue Line Extension toward the northeast consists of the construction of five new underground stations. The project includes 6 kilometers of the tunnel which will be constructed using a Tunnel Boring Machine (TBM). In line with the commitment to integrating sustainability best practices, Envision verification is pursued this project. The Envision reference framework was developed to cover all the sustainable development aspects of an infrastructure project and each phase of its life cycle (planning, design, construction, operations and maintenance, and end-of-life). As a part of this endeavor, low-carbon concrete and shotcrete mixtures are proposed for the linings of TBM and SEM tunnels as well as stations and auxiliary structures. The CO2 emission of the low-carbon concrete and shotcrete mixtures were compared with their typical mixtures and the total CO2 emissions reduction related to the tunnel lining is determined. The study is of strategic significance for achieving emission reduction in the tunnel industry.

Jun 13, 2023

By Robert W. Carn

This paper presents the concepts which are presently being utilized in the design of coal export terminals. Criteria for selecting a viable site and establishing the terminal plan are presented. Factors affecting the design of the terminal as well as the present techniques and procedures in use today to determine the optimum use of equipment will be discussed along with the current trends in export terminal control systems. Finally capital and operating costs for a typical export terminal are reviewed.

Jan 1, 1982

By J. R. Koehler

Mining practices at the Sunnyside Mines, Sunnyside Coal Company, Sunnyside, UT, have been documented by U.S. Bureau of Mines researchers to preserve the extensive history of yield pillar-based longwall gateroad system evolution on the property. An overview of the historical mining conditions, practices, and innovations that resulted in the evolution of the two-entry yield pillar gateroad system currently employed at Sunnyside was developed from interviews of 30 long-time Sunnyside employees. Employing yielding chain pillars at Sunnyside virtually eliminates tailgate pillar bumps and contributes to reducing face bumps. Limiting the overall width of the gateroad system benefits bump control and especially, roof and floor stability.

Jan 1, 1994

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives (RAs) require an air source to supply breathable air to the occupants. This requires pressure relief valves (PRVs) to prevent unsafe pressures from building up within the RA. The Mine Safety and Health Administration (MSHA) mandates that PRVs prevent pressure from exceeding 1.25 kPa (0.18 psi or 5 in H2O), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. Research to date by the National Institute for Occupational Safety and Health (NIOSH) suggests that the design and implementation of PRVs used in RAs has not yet had sufficient performance analysis or technical development. In response to this need, NIOSH tested a variety of PRVs using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork, and various sensors to determine if subject PRVs meet the MSHA requirement. Relief pressures and flow characteristics including opening pressure and flow rate were measured for five different PRVs under a variety of conditions. Subject PRVs included two off-the-shelf modified check valves, two check valves used in MSHA-approved built-in-place (BIP) RAs, and a commercially available valve that was designed for a steel RA and is currently being used in some BIP RAs. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.8 to 6.1 in H2O) and flow rates up to 19.3 m3/min (683 SCFM). INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement [1]. Section 13 of the MINER Act specifically directed NIOSH to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines. This mandate culminated in the 2009 adoption of changes to 30 CFR mining health and safety regulations, requiring underground coal mines to provide mine emergency RAs and associated components, to provide a life-sustaining environment for persons trapped underground. Such RAs can be either self-contained mobile units or built-in-place (BIP) facilities. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One specific criterion for maintaining a safe RA atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi or 5.0 in. H2O), or at a pressure above mine atmospheric pressure in the RA as specified by the manufacturer when the breathable air is supplied by a fan or compressor [2]."

Jan 1, 2017

By Wladyslaw John Cieslewicz

Geologically, this region is occupied by Mesozoids, a folded belt of Triassic and Jurassic sediments and volcanics. Gold mineralization is of Upper Jurassic age. Most of the stream placers formed during the Quaternary. Placer gold was first discovered in 1916. Between 1930 and 1957, mining was carried out by the "Dal'stroi," a Russian death- camp organization. At the mines, "Dal 'stroi" exterminated 5-7 million captives taken from Russia's different colonies, each prisoner extracting 1-2 kg of gold before he died. Since 1966 the mines have been worked mechanically. About 10 mining districts are now active, producing altogether 110-135 tons of gold annually.

Jan 1, 1987

By Robert A. Jankowski, Jonathan Kelly, Edward F. Divers

Results for the first underground test of the ventilated drum in a U.S. coal mine are presented. Tests were conducted by the Bureau of Mines through a contract research program with Foster-Miller, Inc., to evaluate dust control effectiveness in a western mine and for gas control in a full scale laboratory facility. The ventilated drum is designed to reduce the amount of dust from cutting by drawing dust-laden air from the cutting zone through twelve water- powered "dust capture" tubes built into the shell of the shearer drum. High pressure water up to 1 12.48 kg per cm2 (1,600 psig), released from sprays, induces maximum airflow of 1.89 m3/sec (4,000 cfm) from the face side of the drum and provides cleaning for respirable dust and improved methane dispersion. At the gob side of the drum a deflector plate, attached to the cowl arm, turns the water spray and a proportion of the cleaned air back into the cutting zone. More than 50 ventilated drums have been installed to date in England, and their tests carried out on fixed height and single-ended ranging drum shearers have shown reductions in respirable dust of 60-80 pct, as compared with conventional wet cutting. The U.S. test on a double drum shearer showed slightly lower reduction.

Jan 1, 1987

By Michael Forbes, Rick Jeuken

The challenge of managing geological uncertainty in mine planning is central to optimizing resource extraction while minimizing risks and costs. This paper introduces a novel approach to coal mine planning by integrating chance-constrained programming to address the uncertainty inherent in mining operations. The main takeaway from this work is the demonstration that focusing on reducing the variance of high-quality coal blocks, rather than low-quality ones, can lead to better blending outcomes, higher profitability and more efficient resource utilization. The study presents a case study of a coal mining operation, using chance-constrained programming to manage the uncertainty surrounding coal property predictions, specifically the predicted coke strength after reaction (CSR).

Jan 1, 2025

By Paul J. Henkels

Synthetic gypsum is the calcium sulfate co-product of a number of industrial processes. Synthetic gypsum utilization as an alternative to the naturally occurring mineral continues to grow in the gypsum industry. In particular, flue gas desulfurization (FGD) gypsum produced by the electrical utility industry has had a significant impact and a far-reaching effect on the gypsum wallboard manufacturing industry. This paper will discuss the various synthetic gypsum sources verses natural gypsum and highlight issues of use in gypsum wallboard and related products.

Jan 1, 1999

By D. A. Knight

The property is located in the Porgera Valley 600 Km North West of Port Moresby. The remote location is 2500 m above sea level. The mine area has 3,600 mm of annual rainfall and a temperate climate with temperatures ranging from 10" C to 22° C throughout the year. Alluvial gold was reported in the Porgera area in 1938 and has been an important source of revenue for the area for many years. Intermittent exploration was carried out until the 1960's when Placer (PNG) Pty. Ltd. with Mt. Isa Mines commenced an extensive exploration program. The property was brought to production in 1990 by the Porgera Joint Venture group consisting of Mount Isa Mines Ltd, Rennison Goldfield Consolidated Ltd. and Placer Dome Inc, each with a 30% ownership and the Government of Papua New Guinea with a 10% share. Placer Dome Inc. is the manager of the property with construction under the direction of the Placer Dome Technical Services group.

Jan 1, 1992

By H. Bradley Johnson

A number of Federal laws affecting safety and health in the mining industry has been enacted and revised over a period of many years. We have tended to classify these laws and their applicability into three categories: 1) coal mines, 2) metal and nonmetallic mines, and 3) mines with Federal supply contracts. With the growing attention which is being given to mine safety by the Federal government, the entire mining industry should keep aware of all developments in the administration of each of these laws.

Jan 1, 1970

By Feng Dingwu, Chen Jin, Sun Zhongyuan, Peng Shiying

The recent development of rare-earth permanent magnets has impacted the field of magnetic separation. The permanent magnets technology led to the advent of various magnetic separators particularly designed for application in mineral processing. In this paper, a new type of rare-earth PHGMS possessing a higher magnetic field strength in the working zone was developed using finite element analysis techniques. The NdFeB permanent magnets used had properties of 38 MGOe stored energy, and magnetic material flux levels exceed 1.2 T, The combination of scientific and engineering design and suitable matrices can offer an effective separation of industrial minerals, such as kaolin, feldspar, etc. Compared with conventional high intensity electromagnetic separators, the equipment can reduce electrical energy over 80% with lower operation and maintenance costs, and less installation space.

Jan 1, 1995

By G. Sanders

The studies reported on in this paper were initiated to draw attention to the severe contamination problem in the Section 30 drilling program at Chimney Creek. The lithologic-subset sampling study reached a different conclusion from that presented in your paper, and I wish to comment on your subsequent analysis of the data and your conclusions. Request for more complete data In the section on subsampling, you mention that the subordinate lithologies were separated and sampled, yet only the dominant-lithology gold value is plotted in Fig. 4. In a contamination study, the reader is interested in the assay values for the individual subsets. Please include a table of the subsample assay data in your reply. Also, please indicate which analytical methods were used to arrive at the gold values in the subsampling study. Turning barren rock into low-grade ore Figure 5 is very revealing and typical of all of the cross sections in Section 30. Note the long strings of low-grade mineralization spread out for hundreds of feet below the ore zones. There were some very high gold values found in certain contaminated fractions during the subset sampling. The conclusion, here, was that the distinctive, strongly-mineralized dolomite layer was probably loose and crumbly and continued to disintegrate during drilling. This caused salting of the unmineralized rock samples below.

Jan 1, 1993

By C. D. Keith

Erie Mining Company, a pioneer in the iron ore pelletizing industry, has continued to develop methods and equipment to improve cost and quality. Under the management of Pickands Mather & Co., this property, owned by Bethlehem Steel Corporation, Youngstown Sheet and Tube Company, Steel Company of Canada, Ltd., and Interlake, Inc., has initiated a number of operating improvements for the taconite industry. One of the most noteworthy of these, which is applicable to the entire mineral industry, is the principle of fine screening with rappers (FSR). Erie's original efforts in the field of fine screening, which date back to 1961, were described in the April 1967 issue of the MINING ENGINEERING magazine. In that same month, Erie placed into operation a full scale PSR and regrind plant addition, capable of processing 10.3 million long tons of iron ore concentrates, produced by conventional taconite grinding, classification, and magnetic separation methods. Since this first successful commercial operation of the PSR principle et Erie, it has been applied in eight other iron ore beneficiation plants end is being tested by other U.S. and foreign companies. In addition to the use of PSR units at Erie Mining Company, Pickands Mather has applied PSR to other of its managed properties end to projects under development. This paper covers these applications as well as a now application at Erie Mining Company.

Jan 1, 1971

By J. M. Dean, R. L. Grayson, N. P. Reddy, Y. J. Wang

This 1988 survey provided a cross section of computer software use by the US coal industry. From 1250 mailed questionnaires, 171 responses were received, representing a 4.9% sampling of the 3496 US coal mines. Since the distribution of responses by regional stratum matched well with the distribution of mines by stratum, the survey was given statistical validity. A statistical description details the computer use by region, mining type, organizational size, the level of application within the organization, the type of software application used, the variety of computers on which the software was used and the percent of users within engineering, management and general applications categories. Overall, 63.5% of the respondents use computers at some level in their organizations. All of the mines producing more than 454 kt/a (500,000 stpy) used computers. However, for those producing more than 9 kt/a (10,000 stpy) but less than 91 kt/a (100,000stpy), only 44% used computers. Generally, the software applications were still data-processing oriented. The application sophistication grew with increasing mine size. Computer system models and configurations for different sized organizations are recommended based on the configurations used in the industry at the time of the survey.

Jan 1, 1994

By E. Harrison

The Greens Creek Ore Bodies are located approximately 18 miles southwest of Juneau, Alaska in an area on Admiralty Island classified as a non-wilderness national monument. An area-wide stream sediment geochemistry program targeted the deposit in October of 1973. Today, after 37,000 meters of combined surface and underground diamond drilling, three ore zones are known to exist with total reserves approaching 4.1 million tonnes. Lying within moderately folded metasediments of an undetermined age, these orebodies are thought to be of seafloor exhalite orgin and contain unusual and impressive amounts of gold, silver, lead, zinc and copper.

Jan 1, 1986

By P. Todd, K. Dever, P. S. Mills, A. A. Campoli

Resin bolt performance is dependent on the size of the resin annulus, i.e., the difference between the hole and bolt radii. The majority of the millions of resin roof bolts installed each year in the United States employ an annulus of 3.175 or 4.775 mm (0.125 or 0.188 in.). Short encapsulation pull tests with resin annuli of 3.175 and 2.413 mm (0.125 and 0.095 in.) resisted an average of 0.08 t/grouted mm (2.25 st/grouted in.) with no significant variation. Resin loses to simulated fractures increased as annulus size decreased.

Jan 1, 2003

By John R. Marks

The first 0.7 m3 (1 cu yd) diesel load- haul-dump vehicle (LHD) arrived at the Homestake Gold Mine in Lead, SD in I969 to muck a ventilation drift. Others soon followed. Mechanization has subsequently changed stoping methods, manpower requirements, ventilation practice, the definition of minable reserves, and it has impacted safety and health. These have all had a direct bearing on the economics of producing gold ore from deep underground. Mechanized mining Before mechanization, production quotas at Homestake were met by several open cut-and-fill (OCF) mining methods. OCF mining relied on jackleg and wagon drilling, electric and compressed air slushing and cribbed raises brought up through the fill. Even square- set stoping was used until about eight years ago. The mine became 100% mechanized in 1988. The two current stoping methods are mechanized cut-and-fill (MCF) and vertical crater retreat (VCR). In 1992, MCF accounted for 54’S, VCR for 44% and development/uphole for 2% of the 1.4 Mt (1.55 million st) of underground ore produced. These methods are typically ramp- based and use diesel-powered LHDs, trucks, pneumatic drill jumbos and utility vehicles. Electric LHDs and rubber-tired compressed air muckers have also been used in VCR scrams. Pfarr (1991) and Mitchell (1980) provide good overviews of current production methods.

Jan 1, 1993