Search Documents

By A. Masutomi

Although great strides have been made during the past two decades in the reduction of the severity of accidents and injuries in underground coal mining, the number of accidents resulting in disabling injuries and lost time has continued to increase. Looking ahead to the 1990s, the reduction of accidents and incidents typically found in these latter categories should be emphasized in safety training for underground coal mining. Loss control is an approach which shows promise for applications in mine safety training since loss-control strategies focus on the pre-contact stages of an incident rather than on the incident, itself. Applied to safety training, the heightened awareness of personnel to workplace hazards at the pre-contact stages should result in a reduction of accidents and injuries. This paper explains the concept of loss control and shows how it can be applied in the development of the needs assessment for miner training programs. An example, based on research conducted at the continuous-miner worksite, is provided.

Jan 1, 1991

By Jiang Su, Michal Uhrin

"The use of composite linings, consisting of permanent sprayed primary and secondary linings with a sandwiched spray applied waterproofing membrane is expected to improve efficiency and reduce lining thickness, but it also brings complex primary-secondary lining interaction. This issue is further complicated by the uncertainty regarding the long-term behavior and parameters of the sprayed concrete–sprayed membrane interface.This paper aims to address this issue by presentation of a series of numerical analyses of a typical shallow SCL tunnel in soft ground with a range of design assumptions on the interface behavior: (1) compression only; (2) compression and tension; and (3) compression, tension, and shear.The results demonstrate that the assumed interface behavior has a significant impact on the primary-secondary lining interactions. A design approach of ignoring the tension and shear bond at the interface may not be conservative particularly for serviceability. This paper explains the rationale behind these conclusions and discusses the implications for design.INTRODUCTIONSprayed Concrete Tunnel Lining SystemsSprayed concrete linings (SCL) have been used in conventional tunneling for decades. However, details of SCL systems may differ to a large extent depending on ground conditions and specific tunneling methodologies.In hard rock conditions, for example, drill and blast excavation is typically supported by rock bolts and sprayed concrete (NGI 2014). Such tunnels are usually designed fully drained and the above-mentioned support elements considered permanent without the need for a further inner liner. Therefore, there is no structural interaction between separate lining shells to consider.In conventional tunneling in the European Alps, a double shell lining is typically utilized, consisting of an outer (primary) sprayed concrete lining and an inner (secondary) cast-in-place concrete lining, separated by a waterproofing system. The primary lining normally includes rock bolts and may include other support elements. The waterproofing system is usually based on a plastic membrane and a geotextile fleece. The tunnel may be designed fully or partially drained or fully undrained. Although there are two structural lining shells interacting, investigation of such interaction is generally irrelevant to designers because the primary lining is considered only temporary (fully sacrificial in the long term). An overview of reasons for this assumption is given, for example, by Lemke (2014). The secondary lining is designed to resist all foreseeable loads on the tunnel. The primary lining may, in reality, interact structurally with the secondary lining during the life span of the tunnel. However, since the secondary lining design must cover all possible (extreme) scenarios, investigation of such interaction does not bring any value to the design."

Jan 1, 2016

By K. Baba

Liberation of valuable minerals from a gangue matrix during size reduction of multiphase mineral particles is an important objective in mineral separation processes. A methodology for the prediction of volumetric grade distribution from one dimensional, linear intercept image analysis is being developed using a transformation function to describe the relations hi p between the linear and volumetric grade distributions. As part of this research effort it has been found that a transformation function, derived from Monte Carlo simulations of irregularly shaped particles, mainly depends on the volumetric grade and the dispersion density, i.e., the number of nuclei (or grains) per particle. A possible mathematical form for the transformation function is described in detail.

Jan 1, 1985

By Scott G. Britton

In this chapter, I shall discuss railroad con¬struction for modern underground coal mines. Because men, materials, and supplies are being moved more often and farther by rail, the ef¬ficient and safe construction of the system takes on new importance. Most large coal mines are opting to use track haulage over other support transportation systems because of cost, ease of installation, reliability, and other factors. En¬gineers tackling the problem of designing such a transportation network must be aware of all the steps required for an effective transportation system design. This chapter discusses all aspects of efficient trackwork construction. The areas covered in¬clude design factors, laying the track, installing turnouts and switches, and installing trolley wire. Each area includes a description of the steps needed to complete the work.

Jan 1, 1983

By C. Milne, T. M. Dyhr, T. E. Wilson

As time progresses, new concerns regarding long-term post-mining effects are identified, increasing mine closure costs. Regulators responding to public interest must take a “worst case” view and require post-closure monitoring or remediation processes. Although closure costs depend on the size and type of operation, general cost categories are defined, and median values (per acre, or per unit of production) are identified. Closure cost categories, as well as amounts, have increased with time. Except for increased efficiency in earth-moving and water management (surface or subsurface), there are no apparent offsets to a steady rise in closure costs. When the historical trend of closure costs is considered, it is probable that additional cost categories will come into being. For mine operators, the challenge will be to anticipate them and devise cost-effective remedies.

Jan 1, 2003

By Kirk Carlton

This paper deals with a group of subjects so familiar to all of us that we might question the need for discussion. Even so, nearly every day's business turns up expensive examples of differences in understanding, misdirected assumptions and incomplete technical purchase documents. As our international activities increase, so do these problem areas. Their expense in both money and embarrassment gives rise to this attempt to focus a little extra attention on technical criteria and specifications. The two terms ?criteria? and "specifications" are, we believe, worth separating with respect to meaning. They should not be used interchangeably, although they often are. Criteria are by definition "standards for judging", whereas specifications are "enumerations of particulars". In relation to plant or project engineering, the criteria are the general rules and data which apply to the whole project and the specifications are the further listing of detailed requirements for specific contractual items or pieces of equipment. We'll look a little more closely at specifications after we give another minute or two to this "criteria" subject,

Jan 1, 1973

By D. Kaja

The Symons Cone Crusher was invented by Edgar B. Symons in 1923. It was quickly accepted as a superior secondary and tertiary crusher. Nordberg manufactured crushers for the Symons Brothers Co. and in 1928 acquired the Symons Cone business. Since then, the Symons cone has become the standard of the Mining Industry. This is due to the basic rugged design and Nordberg's continued efforts to modernize and upgrade the crusher design over the years. In 1930, the Heavy Duty model was introduced with a 225 kW (300 HP) rating. Then in 1931 the Short Head version was developed to handle finer crushing applications. In 1950, the 7 Ft. XHD design was produced which provided higher crushing force capabilities for harder ores and for smaller product size requirements. Finally, in 1978, the 7 Ft Super Heavy Duty design was created to expand the power rating to 500 HP and to further increase the crushing force limits. The first 7 Ft. Super Heavy Duty crushers were delivered to Bougainville Copper Ltd. in 1978 for the production of primary ball mill feed in a three stage crushing plant with the third stage in closed circuit. The product size was 80% minus 6.35 mm (1/4 in).

Jan 1, 1998

By Kenneth J. Reid, Marian S. Stachowicz

A preliminary evaluation of a new in-stream particle size analyzer has been carried out using materials obtained from a taconite plant in Northern Minnesota. Results are reported for bench scale, pilot scale and full scale tests, the latter being carried out in a taconite plant concentrator. The unit employs a novel scanning laser microscopy principle and details of the equipment configuration and operating principles are presented and discussed. Data acquisition is via an eight channel digital electronic system and particle counts are collected on the basis of reflected light pulse time intervals which are a direct measure of particle size. Output is available as an eight point individual or cumulative size distribution or as computed averages. The practical aspects of sample point location and flow requirements for reproducible results are outlined and discussed.

Jan 1, 1990

By E. A. Laurila

During last years many different types of X-ray fluorescence analysers have appeared in the market most of these instruments being designed for laboratory use. The instruments applied ins continuous processes are usually modifications of these laboratory types. The application of these instruments to the analysis of heavier elements seems to be quite satisfactory. By lighter elements difficulties are caused by the strong absorption of the characteristic fluorescence radiation, which sometimes makes the use of vacuum or helium chambers necessary. In the following an instrument of another type will be described. It has been developed exclusively for the analysis of titanium in ilmenite concentrate, where the content of Ti02 varies between 43 - 46%. Preliminary measurements have shown that in this interval absolute change of 1% in the Ti02 concentration causes a relative change of about 2% in the intensity. Because: the accuracy of 0.5 % Ti02 is sufficient, 1% relative accuracy should be, attained in intensity measurement. The problem is not very easy to solve due to the fact that Ti K radiation is rather soft and the requirement's for accuracy are rather high. Being applied to the analysis during a continuous process may statistically fluctuating variables in connection of sampling and disturbances of many kind set special requirements for the instrument design.

Jan 1, 1960

By David M. Spatz

Team, as defined by Katzenbach and Smith (1993), is a small number of people with complementary skills who are committed to a common purpose, performance goals and approach for which they hold themselves mutually accountable. As the mining industry searches for new ore discoveries increasingly under post-mineral cover, the process of mineral exploration has taken us from prospector to geologist to multidisciplined explorer to multi-disciplinary team. Multidisciplinary exploration techniques have improved in terms of sensitivities and penetration and more than ever before each technique requires specialists with appropriate training and skills to process data and interpret results. To produce a quality product, specialists must collaborate openly and honestly in an atmosphere where the collective result takes into account the knowledge and expertise of each individual and the relationships between all pertinent data sets.

Jan 1, 1998

By D. N. Madge

A survey is given of production scheduling systems currently in use or contemplated for future use in Cominco operations. Emphasis in this presentation is made on the chain of decisions that are made with the help of mathematical programming models. Some attention is devoted to the structural properties of the models.

Jan 1, 1966

By Anibal Gajardo

Clays for building bricks and roofing tiles in Chile are classified as common clays and ball clays, with deposits of sedimentary and residual origin, both Cenozoic in age. Deposits are known from north to south, through 11 of the 13 Chilean Administrative Regions, 18° to 39° South latitude, and from west to east, through three of Chile's main geomorphic features, namely the Coastal Plains, Coastal Range, and Intermediate Depression. Alluvial and lacustrine sedimentary common clay deposits are located in the northern and southern Intermediate Depression. The average chemical composition of clay deposits in I and I1 Regions, is 58 percent Si02, 16 percent A1203, and 4 percent Fe203 by weight; the primary minerals are sericite, quartz, feldspar, and albite. The average chemical composition of clays in Metropolitan, VI, and VIII Regions, is 52 percent Si02, 16 percent A1203, and 6 percent Fe203 by weight; the primary minerals are montmorillonite, quartz, and plagioclase. Residual common clay deposits occur in the Intermediate Depression and in the Coastal Range internal basins, VII, VLII, and IX Regions, and they represent surficial alteration of pumice beds and crystalline rocks. The average chemical composition of clay deposits derived from crystalline rocks is 58 percent SO2, 17 percent A1203, and 9 percent Fe203 by weight; the primary minerals are sericite, quartz, and clinochlore. Clay deposits formed from pumice beds contain 47 percent Si02, 24 percent A1203, and 10 percent Fe203 by weight; the primary minerals are kaolinite, feldspar, and cristobalite. Sedimentary ball clay deposits are located in the Coastal Plains and Coastal Range, VI, VII, VIII, and IX Regions, between 34" and 39" South latitude. The average chemical composition of the ball clay deposits is 51 percent ,902, 28 percent A1203, 5 percent Fe203 by weight; the primary minerals are kaolinite, quartz, and sericite (illite?). These clay deposits supply the Chilean building sector with over one million metric tons (mt) (1.1 million short tons [st]) of material per year. The average growth rate of clay consumption during the period 1993 through 1997 was 10 percent annually. The clays are used by both mechanized plants and handcraft facilities.

Jan 1, 2001

By Sandeep Upadhya, Marc Morgan, Baljinder Bassi, James Fletcher, Mike Deevy, Nishant Nayan

"In order to protect public safety in the event of a deliberate fire attack, underground rail authorities are increasingly considering the need to design for arson-initiated fire scenarios. Where typical design fires for modern rolling stock mean a peak fire size is reached after 12 minutes, an arson-initiated fire reaches its peak within 2-3 minutes. We present the innovations required to successfully incorporate this requirement on a recent design-build project. In stations 3D modelling is used to optimise smoke reservoir designs, smoke chimneys, station boxes and tunnel geometry to allow coordination with structural requirements. In tunnels, novel coupling of one dimensional network modelling and 3D Computational Fluid Dynamics (CFD) is used to improve assessment of complex fire scenarios. Finally, the impact on tunnel structures is assessed through comparison with standard time-temperature curves and risk of explosive spalling. INTRODUCTION An increasing regulatory environment and the appreciable influence that terrorist incidents have had on public safety policy have motivated the need to protect against large arson fires, especially in civil structures and public transport systems. With a greater reliance of a growing urban population on underground subway systems, design of such infrastructure is continually being reassessed and developed worldwide. Underground rail authorities are paying increased consideration to the design of fires - with properties beyond the upper regions of growth and intensity - amongst arson fire studies. Use of fire hardened materials on modern rolling stock means fires caused accidentally can be expected to develop relative slowly. However, recent experiments involving large initiating fires (as would result from an arson attack) have shown rapid fire growth rates and flashover leading to greater maximum heat release rates, Hadjisophocleous (2012), White (2010), and Lönnermark, et al. (2015). This paper describes the challenges and innovations required to complete a detailed design to control smoke from such aggressive super-fast growing fires. Computational modelling is used to demonstrate the required smoke control design by configuring the mechanical exhaust system combined with careful coordination with the architectural and structural design. The design objectives are to provide tenable egress paths in accordance with NFPA 130 (2014) and fire-fighting access. Finally, analysis of the design fire is used to inform the tunnel lining design, reducing the risk of explosive spalling, protecting the asset in the event of a severe fire."

Jan 1, 2016

By Vincent C. Grimshaw

High pressure fluid energy grinding, or jet milling, is a versatile method of continuously fracturing solids into fine particles to gain substantial increases in exposed surface area. Applications in the minerals industries include calcium carbonate, talc, barytes, mica, diatamaceous earth, bauxite, rutile, coal, kaolin, sepiolite, diamonds, etc. The basic principles can be extended to provide continuous drying and delivery of discrete particles from a wet process slurry. The main design and operational features of jet mills and dryers are described, relating energy consumption for both air and steam milling and hot air drying techniques. Mean particle sizes in the order of 1 micron are achieveable from pre-milled feeds, or maintained from similar slurries in the drying mode. Aspects of feed preparation and multi-stage processing are discussed.

Jan 1, 1983

By F. L. Pierson

Since the discovery of 'potash in the Carlsbad area in 1926 and the start of mining operations in 1931, "first mining," operations have been carried on. This is a room and pillar system in which approximately 62% of the total ore is removed. Or the basis of ore reserves and rates of extraction, the life of the mine in the early; days was estimated to be well over 50 years, however, even with an increase by additional ore reserves, it became increasingly apparent that the life of the mine was being shortened considerably by increased production. Further cause for the shortening of mine life was due to the exceptionally weak back over the northeast quadrant of the main orebody which had .caved in on first mining up to a height of 8 feet. Thus, in 1953 the decision was' made to begin pillar pulling, also called, second mining or final mining, and in December of 1953 this program was started after much discussion.

Jan 1, 1965

By M. Woodie

INTRODUCTION Information such as application review to choose the proper style of vibrating screen, parameters that determine the proper size of vibrating screen, engineering design information that governors proper screen design, review of topics that govern proper isolation from structural steel and other topics that dictate proper screen selection for applications will be presented in this paper. Topics like process and application information review to choose the style of screen and how material size and type influences proper type of screen selection (multi-slope, incline, horizontal, linear incline or dewatering) will also be discussed. Parameters will be reviewed that help size the screen for the application. The total amount of surface area to size a screen is critical to the overall success of a screen installation. Once proper style of screen is determined there is an engineering process that is required to design the screen to operate correctly in the environment it will be used. Finite Element Analysis, Dynamic Modeling, Field Vibration Analysis and other engineering tools will be reviewed to best implement a successful vibrating screen installation. TYPES OF SCREENS Multi-Slope Multi-Slope vibrating screens are used where sizing large amounts of tonnage on surface areas that would be smaller than conventional screening where roughly 6” (150mm) minus material is required to be sized. Occasionally larger particle sizes can be screened on the Multi-Slope machine but the effectiveness of the machine can be diminished with larger particle sizes and larger than 4” (100mm) screen opening. The most common and effective size range of screening with these machines is 2” (50mm) minus material. The Multi-Slope screen is used where particle size is not extremely important. Mineral processing, hard rock mining and industries where exact material size is not critical are best suited for this equipment. Because the aggregates industry requires very specific material sizes, the Multi-Slope screen is not suited for most aggregate screen applications. The key to the success of a Multi-Slope screen is proper material presentation at the feed end of the screen. This allows for the material to stratify quickly and disperse the fines through the screen quickly with a relatively thin bed depth at the feed end which allows the undersize material through the screen quickly.

Jan 1, 2019

By Gerald P. Kelton

Over the past quarter of a century, the success of the hydrocyclone as a classifier in closed circuit grinding installations has permitted the introduction of the cyclone into virtually all fields of wet industrial processing. Research and experience gained in these applications have established the optimum cyclone sizes and designs necessary to provide the required performance. Although cyclones are used in widely diverse liquid-solid applications, their use for ultrafine separation clearly demonstrates the importance of a familiarity with previous case studies. Krebs Engineers is firmly dedicated to serving the process industry and has acquired the unsurpassed knowledge and experience to handle all types of separations and classification problems. Cyclones have been used for a number of applications to make what might be considered fine separations. A typical example is in an iron ore grinding circuit where a 381 mm diameter cyclone will classify an overflow product to 85% -44 micron. There is no question that this is a fine separation, but still finer separations are possible, and these are known as ultrafine separations.

Jan 1, 1983

By Stephen Leslie

A multimedia tutorial illustrating the geology and mineral resources of Gulf Coast salt domes has been developed as a pilot project for a course on Texas geology and resources at the University of Texas at Austin. The principal objective of the tutorial is to educate students with limited background in geological sciences about a major local geologic feature and its geologic and economic significance. The content of the tutorial represents materials generally covered in 4 hours of lecture and laboratory instruction. These materials are presented using a flattened hierarchy of topics, each accessible from a central menu, including salt-dome history, salt tectonics, anhydrite and calcite cap rocks, mineral resources, and geophysical character. Information concerning salt-dome geology is communicated using interactive software; sound and animation are used throughout to reinforce key concepts. Visual aspects include field views, hand specimens, and photomicrographs that were digitized from slides. Illustrations were created using a graphics program or scanned from available archives. Each visual element has an accompanying explanation, which in many cases is linked to other parts of the tutorial. Navigation is accomplished using hyper-links or a set of unobtrusive buttons. The program includes a glossary of the major minerals associated with salt domes available as a pull-down menu and digitized video footage of the Gulf of Mexico sea floor to illustrate the active environment of the formation of the salt-dome cap rock. In addition, a group of interactive questions is presented to assess the level of mastery. Technical aspects were accomplished using a Power Macintosh ? 7100AV and a variety of commercial software. Actual linking of information was done with Authorware? 3.0 Educational, an icon-based, multimedia authoring program. Graphic illustration was done with Adobe Illustrator ?; image processing was accomplished using Adobe Photoshop?; video was cap¬tured, edited, and compressed using Adobe Premiere ?. The interactive nature of the project was designed with regard to future means of dissemination, especially on the World Wide Web. This tutorial serves as a template to build additional modules covering the entire course. A modular approach to the coding of the project and extensive self-documentation should ensure the viabil¬ity of the project by allowing other workers with moder¬ate computer skills to complete other lessons within the curriculum framework.

Jan 1, 1999

By P. T. Perdue, F. F. Haywood

INTRODUCTION Monitoring devices used for detecting and measuring airborne radon in mines are limited due to the rugged environment in which they must operate. Personnel monitors now available are either passive or require filters and an air pump. Area air monitors usually have bulky batteries or require electric power service to the instrument. Thus, there are few instruments presently in use in mines capable of discriminating between the various radon isotopes and their daughters. Occasionally it is desirable to determine which radon daughters are the principal dose contributors in mine air. In some areas, such as the Elliot Lake mine in Canada, there exist sizable quantities of 220Rn in the mine air due to 232Th in the ore (Cote and Townsend, 1981). Since there has been recent interest in radon daughters in homes and factories, as well as caves and mines, methods and instrumentation are being developed to address these cases. Some of these methods can be employed in uranium mines. Although there have been very few determinations of the three radon isotopes (222Rn, 220Rn, and 219Rn) and their daughters made in uranium mines, these isotopes have been measured in process buildings and in private homes under circumstances that suggest these isotopes could also be present in uranium mine air (Perdue, Leggett, and Haywood, 1980; Yarborough, 1980) METHODS Cryogenic air sampling was developed about 15 years ago (Rasmussen, 1972) to concentrate various airborne chemicals for later fractional distillation and measurement of various organics using gas chromatography. A version of this technique has been developed to measure tritium, krypton, and other radioactive gases in nuclear power station buildings (Anon, 1980). In this method, fractional distillation is used in conjunction with various detectors to identify the radionuclides present. The cryogenic method to be discussed here was developed at Oak Ridge National Laboratory (ORNL). It uses the liquid air accumulated in a sampling device for a direct analysis of all gamma-ray emitters present. The air sampler (Fig. 1) could be employed in a mine to liquefy air, using the difference between the point of liquefaction of air (~80 deg. Kelvin) and the boiling point of liquid nitrogen (77 deg. Kelvin) to liquefy an air sample. By using a proper orifice at the entry to the sampling vessel, air of any dust concentration and relative humidity [ ] may be sampled. The energy for sampling is provided by the slow evaporation of the liquid nitrogen; no other power source is required. This type of sampler could be used to augment the usual filter and pump, or passive system presently employed to estimate personnel dose from radon daughters. It would also allow measurement of any combination of daughters from the three radon isotopes. Upon completion of sampling, the sampler is closed and removed from the mine. This sampler, with its liquid air contents maintained by the slow evaporation of liquid nitrogen, is taken to the place of measurement. There, the sampler is opened, the accumulation of water and ice in the neck is chiseled down into the liquid air, and the sample is transferred quickly to a precooled counting dewar (Fig. 2). This counting dewar is then placed upon a gamma radiation detector; we recommend a high purity germanium detector. A determination of all the radon daughters can be made in 1 to 4 hours after the sample is taken.

Jan 1, 1981

By P. R. McOllough

The Colorado Department of Highways awarded a contract to construct the Second Bore of the Eisenhower Tunnel in August, 1975. The contract was completed June 29, 1979, nine days ahead of schedule, with¬out major claims or delays. The tunneling involved complex construction through difficult ground conditions. The contract, plans and specifications were specifically planned to more equitably share the risks involved and to minimize adversary relationships. The Department produced a detailed tunnel design and maintained responsibility for the design. The contract employed some new provisions; e.g., a review board for settlement of claims and disputes; escrow documents (contractor's bid documents) to determine the contractor's basis of bid when determining adjustments. The tunnel contract, plans and administrative efforts employed by the owner and contractor were very successful in this project.

Jan 1, 1981