Search Documents

By Neal P. Cochran

It is always a pleasure for me to address a group of mining engineers. I am doubly grateful when I am allotted sufficient time to describe the total Office of Coal Research program. My remarks are directed to our total program but I trust you will all understand my emphasis of the utilization aspect of our activities since that is my portion of the program. From its inception, the Office of Coal Research has sought out creative ideas for improving our national use of coal by developing new uses, improved mining procedures, lower costs, and appropriate studies with respect to the resource itself. Quite early in the game, our Economics and Marketing Division contracted for studies with respect to New England export market, Western coal, and similar items. Our Mining and Preparation Division has successfully developed a packaged coal-fired boiler and has partially developed a packaged fluid-bed type boiler as well. Our Mining and Preparation Division is working in such diverse fields as treatment of sewage with coal and the separation of coal into distinct-petrographic constituents so that all fractions of the coal can be put to the best possible use. We would like to be doing more work on improved mining methods, better preparation techniques, and any other mining improvement that will benefit the industry and our program. The synthetic fuel plants I will describe later will operate seven days per week, 24 hours per day. We would like the mine to operate on this same sort of cycle and are prepared to support research that will lead to this.

Jan 1, 1970

By V. Galla

In the present paper, two large diameter columns 2 m tall and 1.3 m diameter filled with crushed (finer) and run off mine (coarser) heap leach materials respectively were used to perform unsaturated flow studies. Instruments measuring moisture content and matric suction were placed in the columns at different depths as water was applied at calibrated flow rates from the top of the columns. The outflows from the columns were recorded using tipping bucket rain gauge placed at the bottom of the columns. Unsaturated hydraulic parameters were also obtained for the heap leach materials, scalped (passing 4.75 mm sieve size) and whole (passing 37.5 mm sieve size) sample. The measurements obtained from the columns were later compared with unsaturated flow modeling results. The comparison indicated sensitivity towards the sample size selection for unsaturated hydraulic parameters, and initial conditions considered in the model.

Jan 1, 2009

Residential and commercial plumbers in the United States were introduced to Viega?s copper press technology in 1999. In short, the technology allows plumbers and installers to join copper pipe securely in four to seven seconds on pipe sizes of 1.2 to 10 cm (0.5 to 4 in.) by pressing the connections with specialized tools and fittings rather than through sodering or welding. The water- and air-tight technology, first introduced in Germany in 1989, includes three different sealing elements, a variety of materials and a selection of configurations. By eliminating the need to thread or solder pipe, connections and repairs can be made quickly and securely. Installations are also much quicker and as secure as traditional methods.

Jan 1, 2012

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed. The work input is given by the following equation: [111W = 1 Owi( FP FF(1)] where W is the The energy input to the mill, (kWh/st); F is the Feed size based on 80% passed, (µm); P is the Product size based on 80% passed, (µm); and W; is the Work Index, (kWh/st) Methods to determine the Bond Work Index Various methods have been proposed by Bond to determine the Work Index. There are some problems with the Standard Bond Grindability Test: •Requiring a special mill. •Requiring a relatively large amount of sample. •Being relatively time consuming and tedious. [ ] During the recent years, numerous attempts have been made to install faster and easier methods to determine the Work Index. A complete description of these methods is presented by Yap et al. (1982). Determining the Bond Work Index by a new size ball mill During the recent years, researchers at the University of Tehran determined the Bond Work Index, using the Anaconda simplified methods by its Denver 305- x 127-mm (12 x 5-in.) laboratory wet ball mill. The equation used to calculate the Work Index for the above mill containing 16.12 kg (35.5 lbs) of steel balls is as follow: [1 _ 1-1W;=0.54x [P [)(2)] In addition, an attempt has been made to determine the Bond Work Index similar to standard Bond ball mill procedure but by a different ball mill, smaller and in consequent portable and less laborious than the Bond ball mill. Method description Just as the standard Bond grindability test, this method is a locked-cycle dry grinding and screening process that is carried out until steady state condition is reached. Test equipment The test is conducted in a special ball mill, called the New Size Ball Mill (NSBM). The mill is scaled down with a coefficient of two-thirds from the standard Bond ball mill. It measures 200 x 200 mm (8- x 8-in.) inside (instead of 300 x 300 mm or 12 x 12 in. in Bond ball mill). Just like the Bond

Jan 1, 1995

By Joaquin Ruiz

Although Mexico is known for its important base-and precious-metal deposits, and lately oil, some industrial minerals play an important role in the Mexican economy. Sulfur, the most important industrial mineral produced, accounts for approximately 7.5 percent of the total value of mineral production. This commodity is followed by fluorspar, which accounts for 6.4 percent. Predominantly, the fluorspar deposits are very high grade (75 percent CaF) and are contained in lower Cretaceous limestone in the states of Coahuila and San Luis Potosi. Base-metal deposits in the area of Parral (notably San Francisco del Oro), however, have become important fluorite producers in their own right. (San Francisco del Oro has 12 percent fluorite gangue.) Salt from the Guerrero Negro solar-evaporation ponds in Baja California account for 6 percent of the total shares; phosphate from Baja California also accounts for 6 percent. Barite from man to deposits in Lower Cretaceous limestone in Coahuila and exhalative deposits in the Paleozoic section of Sonora account for 1.0 percent. In addition, Mexico is an important producer of gypsum, graphite, and celestite. Although graphite and celestite are not large-scale operations and thus do not contribute much to the Mexican economy, the Mexican graphite and celestite deposits are among the most important in the world; Mexico is one of the world's few sources of celestite. The celestite is in the form of large, high-grade mantos in Cretaceous limestones in northern Mexico.

Jan 1, 1987

By Paul W. Patton, Christopher Scott Smith

The use of ceramic-in-rubber pulley lagging on bulk material belt conveyors is increasing. Many of the applications have been on pulleys originally installed with rubber lagging. There is a consensus that the fiction characteristics of the ceramic material are significantly better but the factors quoted vary, possibly because the more complex traction mechanism of the dimpled ceramic elements on the belt is not well understood. In this paper we will report and evaluate field data from a number of field installations to provide a study of actual friction characteristics in successful applications for those who desire reliable data for using ceramic-in-rubber lagging in new conveyor designs.

Jan 1, 2004

By R. C. Jr. Babcock, V. S. Znamensky

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd. in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 km. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fiber in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd., of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This chapter presents the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits are outlined. Subsequent work by other companies is mentioned, but not de- scribed in detail. This subsequent work did not alter Kennecott's conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd. who have been involved in the project. In particular, thanks go to Ramon Farmer, N.G. Corner, and A.W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this chapter are solely that of the author and result from his involvement in the discovery of the deposits and management of the exploration program. REGIONAL SETTING Ultramafic rocks on the South Island of New Zealand are thought to be Permian in age and occur between crystaIline and metamorphic continental rocks of Precambrian through Cretaceous age in the west, are thought to have once been part of the Antarctic subcontinent, and the extensive geosynclinal graywacke deposits of the Mesozoic New Zealand geosyncline in the east. They consist of the Dun Mountain ultramafics, a 130 km long segment of ultramafic rocks located at the north end of the South Island, and the Red Mountain ul- tramafics that occur in a zone 200 km long in the south half of the South Island as shown in Fig. 1. These two belts, once contiguous, have been offset a distance of 560 km by the still active Al- pine fault, which is analogous in character and offset to the San Andreas fault of the United States. The ultramafic rocks occur within a sequence of Permotriassic volcanic and sedimentary rocks that probably formed at the eastern margin of the continental plate. The ultramafics appear to be tectonically emplaced between Permian lithologies in the Dun Mountain belt (Coleman, 1966), and at the base of or between Permian volcanics and sediments in the Red Mountain belt. The Permotriassic ultramafic volcanic sequence of the Red Mountain ultramafic belt appears to be a typical ophiolite sequence. Ultramafic rocks, mixed mafic intrusive rocks and volcanics, volcanic rocks, and volcanoclastic sediments occur in apparent superposition from east to west in the area of Red Mountain. Farther south, ultramafic rocks are associated with basaltic volcanic rocks and some sediments, and still farther south are emplaced entirely in sediments. These structural compIications of the normal ophiolite sequence have resulted from the coincidence of Permian subduction, early Mesozoic extension and sedimentation, and Cretaceous subduction along the same plate margin (Landis and Bishop, 1972). The general geology in the area of the Red

Jan 1, 1986

By Kent G. Homewood

The well-being of any company is directly related to the well-being of its employees and to the effectiveness with which the personnel resource is managed. In an era when personnel management has steadily become more complex, there is an increased awareness of employee information systems at all levels of management due to: (1) regulations enacted by federal, state, and local government agencies; (2) technological advances within the mining industry which have resulted in the requirement for highly skilled personnel; (3) increasing concern for the confidentiality of employee information; and (4) management's need for information for planning purposes to control costs and for early recognition of trends and potential problems. In the past it was sufficient to maintain records manually. Today computers are necessary to provide information on short notice and effectively manipulate large volumes of' data. This discussion will describe the following aspects of employee information systems: (1) collection and maintenance of information, and (2) applications which include employee health, salary administration, management re- sources, and labor negotiations.

Jan 1, 1979

By JIAQI JIN, Chen-Luh Lin, Amanda N. Erskine, Jan D. Miller, Shijie Wang

The liberation and exposure of valuable mineral grains in ore particles are of significant importance in understanding the efficiency of flotation separations. A flotation feed sample from the Kensington concentrator was scanned by micro Xray computed tomography (micro-XCT), to determine the liberation and exposure of auriferous pyrite grains. The analysis results suggest a satisfying extent of liberation for particle sizes smaller than 212 μm. Theoretical flotation recovery of pyrite for selected particle size fractions was predicted from the three-dimensional liberation and exposure analysis. The plant flotation tail was also characterized by micro-XCT to identify liberated and partially liberated pyrite particles that might not be collected into the concentrate. However, liberation analysis of the tail sample revealed that the majority of liberated pyrite was recovered in the plant flotation circuit. Trainable Weka, a machine learning segmentation approach, was compared with the Watershed thresholding segmentation for the 106 × 45 μm particle size fraction scanned at a voxel size of 1.85 μm. Improved segmentation of small particles was found using the machine learning method.

Mar 1, 2024

By Cherie M. Tilley

The Stillwater Mining Company has acquired a Tunnel Boring Machine to expedite the mine development operations at its Stillwater Mine. The machine purchased by Stillwater was previously owned by Melbourne Metropolitan Board of Works, Melbourne, Australia. The machine was manufactured by Robbins Co. of Kent, Washington. The Stillwater Mine has an extensive system of footwall laterals which are required by the mine development scheme. The initial mine plan called for in excess of 30,500 linear meters (100,000 linear feet) of footwall lateral drifts at a cross section of approximately 3.0 meters in width by 3.75 meters in height (10 feet x 12 feet). A Tunnel Boring Machine was selected for this work. The Robbins machine number is 146-193. This machine is approximately 4 meters (13 feet 5 inches) in diameter. The machine was modified extensively prior to commencing operation at the Stillwater Mine.

Jan 1, 1989

By Michael C. Stanley

The set of discoveries for a mining district or camp is a reflection of the exploration history. In the western Abitibi greenstone belt of Ontario, future exploration can be guided by a study of statistical trends of known gold deposits. In this area simple trends indicate a strong decrease in the contained quantity of gold discovered through time. Much of this decrease is attributed not to falling mining grades but to smaller tonnages of ore. A plot of the largest discovery in each ten year time period suggests that deposit discoverability is following a size-biased sampling model. Cumulative ounces of discovered gold indicate that an asymptotic value has been reached where exploration is not expected to add significantly to known reserves. This is substantiated by a downward trend in the exploration success ratio of the number of new deposits discovered versus the number of new mineral prospects. The set of discovered deposits reflects a non-random sampling process where size- biased modeling suggests that the largest deposits will be discovered early in the exploration effort. It is the exceptionally large deposit contributing to the observed size-biased distribution. Although this pattern is observed for the western Abitibi the model is complicated by recent, large reserve additions that are attributed to the original discovery. There is present in this area a subtle learning process in exploration leading up to the largest discovery. For comparison a learning model was estimated using cumulative size of discovery per unit of time. This model yielded results consistent with the statistical trends and is thought to be a superior forecast of future discoveries in this region.

Jan 1, 1992

By Boris J. Kochanowsky

In the mobile crushing unit system trucks are replaced by a conveyor resulting in a "continuous" almost "fully-automated" operation with all its attendant advantages. In consequence, overall operating costs are greatly reduced. Because of the new designs of large mobile crushing units that have been brought on-to the market, the use of these plants has increased significantly during the last three years. This paper describes the designs of new mobile crushing units, and emphasizes the advantages that such plants offer to the rock products and mining industries. It examines operating costs, and indicates the conditions in which the application of these plants is most profitable.

Jan 1, 1968

By Martin Wehrli, Oliver Schneider

"MOTIVATION Tunnel construction companies must keep costs low, finish projects in less time and still meet the high quality and safety standards. Therefore, their main goal is always to optimize the tunnel excavation process. Traditional geodetical methods are used since more than 100 years to ensure an exact breakthrough of a tunnel. Evolving sensors, sensor fusion and increasing computation resources opened new fields of application for geodetic solutions in tunneling. These solutions offer new ways to reduce costs and risks in tunneling. INTRODUCTION Nowadays in tunneling, geodetical measurement methods are not only used for guidance, but also for various other applications. This paper gives an overview about where geodetical measurements are used today and highlights their benefits for safety and costs aspects. Furthermore, advanced solutions are introduced. In progressive projects, they have already become state of the art technology and are in use daily. STANDARD GEODETICAL MEASUREMENT APPLICATIONS In drill & blast tunnel construction processes, there are many standard geodetical applications used in the different construction phases, each having different requirements regarding accuracy. In the excavation construction stage, guidance tasks and setting-out of various positions is done by the foremen. Thanks to simplified measurement tools, the foremen are enabled to carry out these measurement tasks themselves without requiring deep surveying knowledge. In contrast, deformation analysis and network measurement campaigns need sophisticated planning and a profound education in surveying. Therefore, these tasks are carried out by surveyors. Profile control and as-built documentation is required in each construction phase. Depending on the requirements of the project, this task can be carried out either by the foremen or a specialized surveyor. Table 1 provides an overview over typical surveying tasks in an underground project including information about who is doing the job and the according accuracy requirements. The listed tasks are described in more detail below."

Jan 1, 2016

By Anna Marabini

This paper provides a summary of the studies performed over a period of more than fifteen years by the Italian National Research Council's Mineral Processing Institute in Rome to develop applications for the use of chelating reagents in the flotation of metallic minerals. A description is given of the various phases through which the studied progressed, starting with the combined use of commercial chelating reagents and a neutral oil and then moving on to the synthesis of new long-chain chelate collectors for the flotation of sulphide and oxidized Pb, Zn and Cu minerals. After a series of preliminary tests which confirmed the possibility of floating various metallic minerals with commercial reagents containing chelating groups exerting specific action on given cations, the studies were addressed to the development of a theoretical method of choosing chelating groups that exert selective action on one metallic mineral rather than others. The theoretical approach was based on thermodynamic data concerning the chemical equilibria in solution. The validity of the method has been proved in numerous cases by flotation tests on pure minerals. Subsequently the research was directed towards the design and synthesis of reagents with a mixed aliphatic-aromatic structure containing chelating groups for Pb and Zn and an alcoxyl chain of various length, position and configuration. The flotation results obtained on oxidized and mixed Zn-Pb ores provided interesting pointers for designing the nonpolar portion. The structural criteria identified via these studies were interpreted on the basis of chemical and steric considerations. A description is given of a new synthetic chelate collector which is effective in the selective flotation of Cu minerals from complex sulphides. The fact that this reagents is more selective than xanthate is demonstrated by comparative flotation tests on actual ores.

Jan 1, 1994

By David L. Martin

This paper discusses the development of a SLAM II* simulation model with imbedded optimization modules designed M evaluate mineral exploration and exploitation strategies. The model traces through a sequential exploration program, evaluating each deposit site based upon geologic information and potential profitability of the site. At a specified time during the simulation, a new production plan is developed for currently producing deposits which takes into account the planning horizon and deposits which are currently being explored. Potential uses of the model by geologists, engineers, and management decision makers include setting corporate objectives and policies on exploration and production. The model is also useful for testing past decisions to evaluate decision making criteria and evaluating mineral deposit profit potential.

Jan 1, 1983

With commodity prices rising again and market conditions stabilizing, the Metals Economics Group (MEG) found that most mining companies increased their exploration budgets in 2010. In the groups 21st edition of the Corporate Exploration Strategies (CES), MEG found a 44-percent rise in the estimated worldwide exploration total for 2010. MEG found that the estimated total 2010 budget for nonferrous metals exploration reached $12.1 billion, reinstating almost two-thirds of the industry?s $6 billion in cuts to exploration in 2009. Nonferrous exploration refers to expenditures related to precious and base metals, diamonds, uranium and some industrial minerals; it excludes iron ore, aluminum, coal, and oil and gas. In 2008, exploration budgets were at an all-time high of $14.4 billion. This capped a six-year run in which budgets rose. In 2009, nonferrous exploration budgets dropped 42 percent in 2009 as the global economic crisis and declining prices for almost all commodities took their toll on the industry. Metals prices - the primary driver of exploration spending - have improved markedly since bottoming in early 2009, and have traded well above their long-term trends throughout 2010. In response, major, intermediate and junior companies have all increased their aggregate exploration allocations in 2010. In particular, the significant improvement in the availability of equity financings for the juniors over the past 12 to 18 months has allowed this group to account for the largest share of the overall increase in exploration spending this year.

Jan 1, 2011

By N. Dahmen

The Robbins Mobile miner has been in development for more than ten years. Two machines have been trialed in mining environments. While day to day performance to date has fallen short of the levels anticipated, instantaneous performance has been impressive for given rock conditions and continues to encourage further development. The Pasminco mobile miner has been committed for a 1.8km main decline extension at Broken Hill. M.I.M. Holdings, parent company of Mount Isa Mines, owner of the first mobile miner, are considering a new machine for McArthur River. Robbins, Pasminco, and The Centre for Mining Technology and Construction have, joined forces to accelerate development of .mechanical rock cutting techniques in general, and of the Mobile Miner in particular.

Jan 1, 1995

By M. Ge, C. Mborah

"The acoustic emission/microseismic monitoring (AE/MS) technique has widely been used in the mining environment for the monitoring of rock mass stability. A successful implementation of the method is hinged on being able to accurately determine the P- or S-wave arrival which is then used in the determination of the source of an event. Determination of the arrival phase is usually performed visually by a human expert. However, the mining environment is characterized by high noise levels and different noise types of varying intensities. Therefore, performing manual phase picking on time series data acquired from the AE/MS monitoring system can sometimes be tedious and time consuming if not impossible. In this paper, a proposal for improving manual P-wave phase arrival picks is discussed. The method involves the filtering of the AE/MS data using a stationary discrete wavelet transform (SDWT) method. After filtering, appropriate scales/levels of the multi-level decomposition process are then selected for further processing. The first step in the picking process after filtering, requires the computation of the signal power and the root mean square (RMS) using the signal amplitudes at each scale. The preliminary P-phase arrival time is picked using the results of the calculated power and RMS values respectively. The calculated RMS values are then superimposed on the calculated power values to determine the final arrival picks. If the arrival time picks obtained by both methods coincide or are within 5 to 10 sample points, the pick is considered reliable. The accuracy of the method was verified using AE/MS data from two datasets obtained from two separate underground mines. The results of the study showed that the picking method is reliable and robust. Based on the data studied, it can be concluded that the method will help reduce the time usually spent in processing AE/MS data from mines. INTRODUCTION A successful identification and location of the source of acoustic emission/microseismic (AE/MS) events is mainly dependent on the onset time of the P-wave phase. In many seismic networks, initial picks are performed by picking algorithms followed by manual picks by human experts. If the waveform signal-to-noise ratio (SNR) is low, the P-wave onset time picks by the human expert is generally reliable and accurate [1]. However, for waveforms with high SNR, picking of the P-wave onset could be a major challenge. Also, due to the volume of data acquired daily, manual processing could be stressful and time consuming [2]. These challenges continue to provide motivation for alternative means of providing reliable and efficient ways of improving manual phase picking. The AE/MS technique has been an intergral part of safety monitoring in mines [3] due to its capacity to identify zones of instability in a monitoring area. To obtain an accurate source of an AE/MS event however depends on the quality of the data used for P-wave phase picking [4, 5]. AE/MS data from mines are generally contaminated with excessive background noise generated by the different mining operations. The AE/MS signals of interest are mostly buried in background noise which makes it difficult to pick the P-wave phase arrivals [4]. Processing AE/MS data acquired in noisy environment remains a major challenge due to the weak nature of AE/MS signals [6]. As noted by [4] most of the data recorded in the mine environment are mainly due to events not related to AE/MS events of interest. The complexity of data in this type of environment makes the detection and picking of P-wave arrival by human experts a very difficult task."

Jan 1, 2017

By Philani Larrance Ngwenyama, Ronald CW Webber-Youngman

Through-the-Earth (TTE) communication systems were developed to provide post-accident communication in underground mines. Unlike primary tracking systems, they do not require any major infrastructure installations underground. Instead, they use the Earth’s overburden as the medium or channel for the transmission of electromagnetic waves between surface and underground. Under ideal conditions, TTE communication systems should be able to provide full-duplex, two-way voice, text and data communication. However, this will depend on the design and optimization of the different types of TTE communication systems (that is, antenna and electrodes), and understanding of the rock properties and their influence on the transmission of signals. This can help simulate and model the transmission efficiencies and predict the possible range and data rates. Being able to optimize the performances of these systems can enhance rescue missions, improving the chances of saving trapped miners, and ultimately reduce fatality rates across the mining industry.

Feb 1, 2025

By K. R. Weller

In recent years, a variety of new or substantially modified grinding machines have been offered to the mining industry with claims of improved performance relative to standard grinding machines especially rod and ball mills. The incentive for developing such new machines is high, because costs associated with grinding are a very substantial part of the total costs of processing run-of-mine ore, and gold ores are no exception in this regard. The incentive is also high because of the very low conversion of input energy to comminution energy in most tumbling mills. If the most energy-efficient means of mechanical size reduction is slow compression of single particles, then this energy amounts to only about 3% of that used in tumbling mills. It would seem, therefore, that there is a huge potential to do better. This paper examines three types of grinding machine for which claims of higher energy utilisation ( amongst other beneficial claims) have been made, namely the high pressure grinding rolls, the vibrating drum mill and various styles of stirred mill. It presents evidence concerning the claims, examines the range of particle size and particle size reduction over which benefits might reasonably be expected to accrue, discusses the major issues in contention and briefly describes the research the CSIRO Division of Minerals has in progress, both independently and collaboratively, the latter mainly with the Julius Kruttschnitt Mineral Research Centre (JKMRC) via the Cooperative Research Centre for Mining Technology and Equipment (CMTE) and the Australian Mineral Industries Research Association (AMIRA). There are many criteria which may be chosen to assess relative performance of grinding machines. Those used below are:

Jan 1, 1995