Search Documents

By C. C. White

Although many notable scientific investigations relating to roof control have been made, roof control still must be considered one of the more baffling problems confronting the miner. Each year contributions are made to our understanding and techniques in dealing with various single phases of the overall problem, however, an equation considering all the variables involved in roof control, if formulated, would indeed be hopelessly complex. Among the factors to be considered is first, gravity which is always acting but which is sometimes less of a problem than lateral forces. There are lateral forces due to expansion, resulting from the weight of overlying rock; to these must be added lateral stresses of orogenic or tectonic orgin, which may be enormous. Stresses due to plastic flow of beds, water pressure, gas pressure, expansion due to absorption of water, faults, joints, fractures, pot heads, and the like may complicate the solution. Therefore, we must base decisions on roof control, and roof bolting in particular, largely on experience, and far too often on few "knowns" and many "unknowns", The development of "in situ" roof trusses may prove of benefit because, they unlike roof bolting, promise positive calculable roof support. These trusses require installation of steel tensioned rods in the roof, which rods are arranged to produce a stress pattern similar to a bridge truss, the roof rock acting to transmit the compression forces. The simplest form of truss (see figure 1) consists merely of two steel rods anchored at the back of holes drilled at an angle of approximately 45° over the pillars, collared near the the middle of the room, the lower ends of the rods being connected together by tierods and turnbuckles. Used in this way, a 3/4" diameter rod can offer greater support than a 10" x 5-3/4" wide flange steel beam. By tightening the turnbuckle, uplist on the roof can be produced,, the downward reaction being transmitted to the pillars by the rods. This simplest form of truss has been used in rooms up to 24' in width. Trusses of four panels, that is, consisting of a truss within a truss, as shown in figure 2, have been used successfully in rooms 30' wide. (figs 2 & 3) It appears a 6 panel truss could be used in a 40, wide room.

Jan 1, 1968

By Paul D. Tavares, John Forbes, Eric R. Drooff

As the existing major U.S. - Canada rail tunnel was too small to accommodate double-stack container cars, Canadian National Railways is constructing a new parallel tunnel with a 50% greater diameter. Starting in Sarnia, Ontario, the new shallow-cover bored tunnel runs under a large research building and several other structures in an oil refinery before travelling under the St. Clair River. Maximum predicted settlements to be caused by the 9.2 meter diameter earth pressure balance TBM in the soft St. Clair till were in excess of 100 millimeters. As such, these settlements had the potential to cause severe damage and disruption to the existing refinery. In order to reinforce the soft clays below the refinery research building and other structures, and to compensate for settlement caused by the tunnelling, the ground improvement method of Soil Fracture grouting was successfully applied for the first time in North America. This paper will describe the details of both the soil fracture grouting application and the elaborate electrolevel remote monitoring system used.

Jan 1, 1995

By Silas Li, Michael Harris-Gifford, Jason Choi, William H. Hansmire

Twin-bore tunnels with a single track in each tunnel are currently the most common subway tunnel configuration. However, a large diameter single-bore tunnel with two tracks separated by a center wall could replace twin-bore tunnels and introduce potential benefits but require necessary modifications to the subway system. In particular, a nominal 40-foot-diameter single-bore tunnel can be considered in lieu of nominal 20-foot-diameter twin-bore tunnels. This paper discusses the benefits and modifications introduced by replacing twin-bore tunnels with a single-bore tunnel, with respect to various elements of the subway related to the tunnel, stations, track, and tunnel systems.

Dec 1, 2022

By G. W. R. Kuzyk

The Underground Research Laboratory (URL) , a major geotechnical research facility, is currently being developed by Atomic Energy of Canada Limited (AECL) , 120 km northeast of Winnipeg, Manitoba. The URL is part of the Canadian Nuclear Fuel Waste Management Program, which is assessing the concept of nuclear fuel waste disposal in a vault deep in stable plutonic rock of the Canadian Shield (Simmons, 1986). Comprehensive geotechnical research and development activities are being carried out in conjunction with excavation? and construction of the underground facilities.

Jan 1, 1989

By William Lodding

Unlike most ore minerals, the raw materials for lightweight-aggregate, such as clays and shales are abundant everywhere. In view of this ample choice, what are the reasons for many plant failures attributed to the raw material? How can we arrive at a proper choice of the raw material, the proper processing method for the chosen material, predict its behaviour in a plant and the properties of the final product? Determine the uniformity of the raw material and possible harmful impurities? One basic choice is sintered versus kiln-fired aggregate. It will be based on market preferences and availability of the raw material. Almost in every case a good raw material for one process is poison for the other.

Jan 1, 1964

By L. M. English

A basic model was developed to help assess methane control needs for the longwall mining of coal in gassy areas. Rather than depending on reservoir and rock mechanical theories, it uses an empirically determined gas emission rate as an input, and it operates on the assumption that, within a specific region and zone, gas emissions will be relatively equivalent for uniform incremental volumes of gob created by mining. The computer program divides longwall panels into segments, keeps track of the face advance and generates emission rates and volumes for both the entire panel and for individual zones within the panel by summing values for all undermined segments. This model can aid in the determina¬tion of the number, size and location of vertical wells or other methane-control applications that are needed for gob gas control.

Jan 1, 2000

By I. K. Kapageridis

Environmental management and planning requires the integration of large volumes of disparate information from many sources and the analysis of this information with efficient tools for assessment and evaluation. Effective methods of communication that allow interactive participation in the planning, assessment and decision-making processes are also very important. The VULCAN software package from Maptek (Pty) Ltd comprises a large number of 3D graphical tools within an interactive 3D interface called ENVISAGE. These tools are designed and developed to help engineers and scientists to identify and solve environmental problems. The combination of VULCAN 3D Software and the I-SiTE 3D Laser Imaging system leads to powerful solutions for environmental management. This paper presents the capabilities of this integrated system and its applications for environmental management.

Jan 1, 2002

By D. Dimitriadis, T. Polglase, M. M. Botz, W. Phillips, R. Jenny

Cyanidation processes for the extraction of gold or silver frequently involve the processing of sulfurcontaining solids that react with cyanide to form thiocyanate. The formation of thiocyanate is an undesired side reaction, and in many cases thiocyanate formation results in a prohibitively high cyanide consumption. With the increasing number of gold and silver mining projects that involve the processing of sulfide ores or concentrates or that utilize a biological sulfur oxidation process, more attention is being focused on minimizing thiocyanate formation and in treating solutions to eliminate toxicity associated with thiocyanate. Though not yet commercially applied, there are several processes available to recover cyanide from thiocyanate to reduce tailings toxicity and to allow the reuse of cyanide otherwise lost to thiocyanate formation. This paper presents an overview of processes available for recovering cyanide from thiocyanate along with estimated operating costs for the processes. Pilot testing data suggests that in some cases cyanide can be recovered from thiocyanate for approximately the same cost as newly purchased cyanide.

Jan 1, 2002

By N. P. Reddy, Y. J. Wang

This paper describes an experimental setup for multiple fan ventilation systems at the ventilation laboratory of the West Virginia University Department of Mining Engineering. Housed in a 30-ft x 70 -ft room, the experimental setup consists of three 18-in., variable-speed, axial flow fans; an 18-in. -diam, fiberglass tubing; associated fittings for arranging networks; and a picot-tube measuring and data-acquisition system. The fiberglass tubing and fans can be organized into non-planar networks of two or three fans. The setup is mainly designed for studying the characteristic curves, operating points and fan stall for multiple fan ventilation systems.

Jan 1, 1993

By Angela Binder, Oliver Langefeld

"The future of mining will be characterized not only by the application of modern technology, but also by the harmonization of economic, environmental and social issues. These areas set major future challenges which are complex and demand extensive knowledge. As an example, mining of highly complex orebodies for the supply of often critical raw materials, needs to consider technically demanding and cost-intensive extraction issues. The amount of tailings, which need to be stored, increases with the amount of ore mined. Therefore, the negative impact on environment and society increases. Hence mining becomes expensive with regard to all three aspects: economy, environment and society. In view of a sustainable mining practice this challenge should be used as an opportunity. The positive impact should be maximized for present and future generations. The objective is to create and use the mining openings in an optimum way related to sustainability. The approach of Blue Mining, which focuses on energy and ergonomics in the field of Sustainable Development, enhances the closure planning by recommending subsequent usage of such openings for energy storage. The approach fosters among others the implementation of the 7th Goal for Sustainable Development defined by the United Nations with the assurance of access to affordable, reliable, sustainable and modern energy for all. The usage of underground storage increases the stability of solar and water power usage, which are otherwise unreliable. Blue Mining embeds these issues in the main planning effort long before groundbreaking. This approach involves experience from past and current projects. This paper introduces the concept of Blue Mining with respect to post-mining utilization of a mine for energy storage. Methods and perspectives are presented with examples covering best-practices and lessons-learned."

Jan 1, 2017

? The U.S. depends on minerals for economic growth and development, and for national security and defense. ? Public lands are an important, long-term source of essential minerals. ? Access to public lands for mineral exploration and development has become more difficult as large tracts of land have been designated for other uses. ? Mineral-bearing areas on public lands are routinely withdrawn or restricted from development before comprehensive resource inventories and economic assessments have been made.

Jan 1, 2011

By R. Schmidt

The computational fluid dynamics (CFD) technique was used to analyze and optimize the design of the dynamic air classifier integral to Raymond® Bowl Mills. Flow patterns and particle behaviors were modeled in the RB Bowl Mill equipped with various classifier designs. These CFD simulations resulted in the development of a hybrid turbine classifier that has now been field-tested, yielding significant improvements to both mill throughput and product size distribution. This paper demonstrates the viability of CFD as a tool for air classifier design and as a technique that can be extrapolated for use with other pulverizer and classifier arrangements.

Jan 1, 2004

By Khosrow Bakhtar, Robert E. Cameron, Arfon H. Jones

The use of rock simulators in rock mechanics research greatly expands the scope of the problems that can be investigated with physical models. However, the exact reproduction of full scale conditions, or absolute simulitude, is not obtainable on a small scale model. For this to be possible, the scales of length, time, and pressure (or mass) must be changed without altering the theoretical equations that describe the behavior of materials concerned. In using rock simulants for physical modeling of structures designed in rock, the geometry of full scale structure is reduced to a size suitable for the available testing machine. This will require the strength related properties to be scaled down. Simulation should be representative of the in situ conditions. Complete simulation will require that friction parameters and the stress ratios be matched exactly between prototype and model. The procedure involved in application of physical modeling for rock mechanics research is discussed in the following pages. Background, theoretical approach, and anticipated benefits to the research community are also elaborated.

Jan 1, 1986

By Ricardo Presnell, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Douglas N. Halbe

Large (> 100,000 oz.) sediment hosted disseminated gold (SHDG) deposits are often spatially associated with anticlines. Many SHDG deposits are within or closely associated with windows. Windows are erosional manifestations of fold culminations (4-way closed anticlines). Hydrocarbons are often trapped in fold culminations in the Canadian Rockies, and may account for degraded hydrocarbons in many SHDG deposits. In the Eastern Basin and Range Province, Mesozoic anticlines may have been large scale conduits fm gold bearing Mesozoic and Cenozoic hydrothermal fluids which became trapped and/or concentrated at the fold culminations.

Jan 1, 1990

By B. Dabrowski, J. D. Miller, D. Halbe, J. Hupka

An air-sparged hydrocyclone (ASH) mobile system was evaluated for continuous stripping and recovery of cyanide (the AVR process) from process water at a gold plant site. The ASH unit performed exceptionally well as an absorber. HCN was removed from the gas phase in a single one second pass with an efficiency exceeding 99%. HCN concentration in the discharged gas phase was lower than 10 ppm, which provided for a safe working environment. The stripping efficiency, controlled by the Henry’s Law constant, exceeded 40% in one pass.

Jan 1, 2004

By Randal J. Barnes

In, any open pit mine the ability to make accurate production estimations for the shovel-truck system is an important asset. This is true in an operating mine wishing to estimate production under a set of system modifications (i.e. more trucks, fewer loaders, change in roads, etc.), as well as in the pre- mining planning stages of a property. Many different methods have been proposed for solving this problem; some of the methods rely heavily on "rules of thumb" while others are highly mathematical and require access to a high speed digital computer. Analysis of shovel-truck systems with the use of simulation models is a widely accepted technique within the industry. Through the use of such models it is possible to account for much of the inherent variability of the system and thus produce meaningful results. However, simulation studies are expensive. Formulation and setup of the actual simulation model requires a significant commitment of time and energy. In addition, the cost of the necessary computer runs is often of considerable magnitude.

Jan 1, 1979

By John T. MacWaters, George H. Milly

INTRODUCTION This paper describes operational procedures and instrumentation which were developed to implement a patented method of detecting and locating uranium ore bodies. All equipment was designed for accurate and reliable use under difficult field conditions. Data resulting from these developments, some of which are incorporated in a companion paper for this conference*, have contributed to our understanding, of the nature and significance of naturally-occurring radon exposures. Further applications of these techniques may prove useful in studying anthropogenic radon in evaluating the significance of variability in radon flux, or in taking proper account of the contribution of natural radon to ambient radon concentrations, particularly in mineralized regions. OPERATIONAL PROCEDURES The uranium search technique employed by GEOMET begins with a [reconnaissance mode], which utilizes a series of ambient air filter samples taken from a moving or standing vehicle to detect anamalous concentrations of radon. These samples are normally taken at night under stable (temperature inversion) or neutral atmospheric conditions, to avoid the rapid dispersion of the radon clouds typical of daytime turbulent conditions. Radon daughters formed by the decay of radon quickly attach to ambient aerosol particles and are captured on the surface of a membrane filter during a five-minute sampling period. The filter is placed in a portable alpha scintillation counter, and a five-minute count is started at a preset time after the completion of the sampling period. This count is followed immediately by a second five-minute count to enable determination of the cloud age, based on consideration of the relative half-lives of the initial radon daughters. With the use of tables computed from the mathematics of the uranium decay process, and with the measured radon background accounted for, the first and second counts are used to estimate the time which has elapsed since the pure radon initially emanated from the earth's surface. This cloud age, combined with wind speed and direction measurements made at the beginning and end of each sample, as well as with an understanding of the effects of local terrain features on wind trajectory, provides an estimate of the Probable location of the source. In practice the reconnaissance mode involves one vehicle with a single operator to take the five-minute samples, moving or standing, along any available roads or trails in the area to be covered. Under the usual nighttime stable conditions the cool air flows downslope and downvalley, and the operator will pay special attention to locations along the axes and confluences of the natural downflow patterns. These facilitate sampling of large air drainage areas. Successful detection of sources of radon based on high concentrations of radon daughters, and substantiated by evidence of "fresh" clouds, are frequently made on the basis of a relatively few samples taken judiciously by an experienced operator during a reconnaissance. At this point he has a choice: he can continue to cover the designated reconnaissance area, leaving the localization of any anomalous radon detections to await the ranking of detections by priority, or he can continue with localization of the detected source, either alone or by radioing for another vehicle to assist in triangulation operations. Localization of a source involves skillful and experienced use of the continuously collected data on concentration, age, and wind speed and direction, together with knowledge of the terrain from observation and contour maps, and exploitation of the available roads. Since age ratios are dependent solely on proximity of the source and wind speed, decreasing [cloud ages] based on statistically significant increasing age ratios represent the most useful. information in localization. The [magnitude of the concentration] of radon daughter products is also useful; however, it may vary widely for a variety of reasons during sampling for a localization, thus making this a secondary parameter for localization. Large values of concentration are of course useful; typical results for successful detection of a strong anomaly would yield alpha counts ranging from 10 to 25 times background values. These counts are convertible to ambient radon concentrations by appropriate consideration of the decay process. Successful localizations of radon sources using this procedure with ambient atmospheric measurements normally will narrow a source location to within an area ranging in size from less than a quarter of a square mile to at most a square mile, and frequently give information on the probable shape of the source (in plan view) on the earth's surface. Judicious use of this procedure could undoubtedly provide finer localization, but the coarser results just described are adequate for this Phase of GEOMET's uranium exploration procedures.

Jan 1, 1981

By R. Hogg, A. C. Maffei, D. T. Ray

Based on standard population balance models for agglomeration and size reduction processes, a simplified model has been developed to describe simultaneous growth and breakage in the flocculation of agitated suspensions. The results of semi-batch flocculation tests have been used for estimation of the model parameters and empirical relationships have been obtained to describe the effects of process variables and to establish scale-up criteria. Application of the model to the design, operation and control of continuous flocculation processes is discussed.

Jan 1, 1990

By S. D. Thompson, G. T. Lineberry, A. J. Basu

Conveyor belt haulage has become the preferred mainline transport method in underground coal mining, especially for multi-unit mines. Proper designs for belts (width and speed) and surge bins (placement, capacity, and discharge rate) are necessary to achieve efficient mine haul- age. Two computer simulation models, CMBCS and BELTSIM, available for designing these parameters were compared. These comparisons included modeling, input data requirements, statistical flexibility, accuracy of simulated loading, and execution time.

Jan 1, 1991

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high-expansion foam generator. Thus allows fire fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600 ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

Jan 1, 1996