Search Documents

By J. Hanna, J. Jung

Researchers at The University of Alabama have recently developed a two-step method for the treatment of phosphorus sludge. The process includes the bulk removal of phosphorus by physical separation techniques followed by the remediation of the residual P4 in the sludge using a novel, wet, air-oxidation technique known as "HSAD." Tests made on electric furnace, phosphorus sludge samples have demonstrated that an essentially complete and fast removal of the contained P4 can be achieved by the HSAD wet oxidation treatment. Further studies were made to determine the applicability of the two-step process to sludges of different origins, pretreatments, storage conditions and P4 contents. The present work discusses the mechanisms and factors controlling the HSAD, wet, air-oxidation remediation approach.

Jan 1, 1993

By Kefton H. Teague

Olivine was first described and named by Warner in 1790. It is an olive green to greenish gray colored magnesium-iron silicate containing a mixture, in solid solution, of fosterite (Mg2SiO4) and fayalite (Fe2SiO4). Ratios between fosterite and fayalite in olivine are somewhat variable, but in general olivine contains at least 85% fosterite. Specific gravity is variable also, depending on the ratios of fosterite to fayalite. As a rule it is in the 3.2 - 3.4 range. All commercial olivine is obtained from the rock dunite, the most basic member of the peridotite group. Dunites, in addition to being composed primarily of olivine, generally contain assessory pyroxenes and spinels (chromite and magnetite). Dunites', when altered by hydrothermal solutions or metamorphism, often contain alteration minerals such as talc, serpentine, chlorite, vermiculite and amphiboles. In the 1930's and 40's considerable research was conducted on olivine for use as a refractory, plant food raw material, magnesium source for metal, and a source for magnesium chemicals. This research met with only limited success.

Jan 1, 1977

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

The main purpose of mine ventilation design is to provide sufficient quantity and quality of air to the workers and to dilute methane and other contaminants. It is generally perceived that the additional air along the longwall face will improve methane dilution on the face and in the tailgate. However, computational fluid dynamics (CFD) modeling efforts at the Colorado School of Mines (CSM) under a National Institute for Occupational Safety and Health (NIOSH) funded research project have found that higher flow velocities along the longwall face are shown to increase the pressure differential between the gob and longwall face allowing more methane to be entrained in the active face and tailgate (TG) area, thereby negating the dilution effect. The increased face ventilation causes an increase in pressure along the headgate side which allows more oxygen to ingress into the gob area, thereby increasing the amount of oxygen available to form explosive methane air mixtures in the gob and to support spontaneous combustion of the coal. Two things are happening at two different locations along the longwall face, increase in pressure as the flow enters the active area cause an increase in pressure which forces more oxygen into the gob, but as the flow is developed along the longwall face, the higher velocities causes greater pressure drop allowing methane to enter the active face further downstream from the headgate (HG) towards the tailgate side. In this paper, a parametric study will be presented to discuss the effect that varying the face air quantity has on methane concentrations in the tailgate and formation of explosive gas zones (EGZs) in the gob. Counter to conventional wisdom, it appears that increased longwall face air quantities may increase the explosion hazard as they result in increased EGZ volumes in the gob, along with increased methane quantities in the tailgate return.

Jan 1, 2015

By K. V. Raj

"Air inversion is a meteorological phenomenon generally occurs during winter times. Release of pollutants below the inversion height in an open-pit mine during periods of weak winds and consequently weak vertical mixing may result in very high concentrations of primary and secondary pollutants, causing serious consequences for health and safety of miners. Mine operations cease if the concentration of NOx or CO exceeds the threshold limit value (TLV) of the pollutants. Artificial ventilation is required to dilute the pollutants to an extent that mine workers can safely resume work. Studies of the turbulence parameters suggest that effective ventilation of the pit and removal of pollutants can be accomplished if a large enough mixing length in the open pit can be created. Turbulent mixing by eddies of different length scales under an inversion layer is product of wind shear, thermal gradient and buoyancy. The main result of turbulence is mixing of the atmospheric profile and transport of momentum. Computational fluid dynamics (CFD) Simulation results of a novel mitigation approach using cloud cover will be presented in this paper. INTRODUCTION In extreme climatic conditions, deep open-pit mines tend to trap pollutants at the pit bottom due to air inversions. Keeping open pits adequately ventilated is a considerable challenge for the mining community. Mine operators in cold regions are very familiar with this problem, the severity of which can be judged from Figures 1 and 2. The top portion of the figures show clear sky and snow covered benches. The brown haze, containing various contaminants accumulated over time in the pit under the air inversion, can be seen in the bottom portion of the figures. Several Arctic or subarctic mines have reported air inversions. Even Rio Tinto’s Bingham Canyon pit in Utah has reported local air inversions from time to time [1].Mitigation of pollutants in deep open-pit mines in the Arctic is a challenging task. Release of pollutants below the inversion height in an open-pit mine during periods of weak winds and consequently weak vertical mixing may result in very high concentrations of primary and secondary pollutants, causing serious consequences for human health. Mine operations cease if the concentration of any one of the pollutants (NOx or CO) exceeds the TLV. Sustained cessation of a mine operation has serious economic consequences. For continued mining operation, the levels of pollutants must be below the TLVs. If no significant synoptic meteorological situation changes during an inversion, a warm air mass sits over the cold air mass within the open pit. Artificial ventilation is required to dilute the pollutants to an extent that mine workers can safely resume work. Some of the early approaches in artificially ventilating open pits were attempted in the USSR. Most of the studies by Soviet researchers suggested the use of turbojets and turbo-propeller engines, airscrews, axial pit fans, and meteotrons [2, 3]. However, the majority of these studies were only theoretical in nature, with no evidence of an approach that really worked in practice."

Jan 1, 2017

By Keith S. Liddell

he selection of mill design parameters to suit the applica­tion requirements can result in quite different operating parame­ters for each generic type of application, even though the basic mechanical layout of the mills may remain similar. The selection of the type and size of grinding media is very important to efficient and cost-effective operation, and to ensuring that the milled product achieves the required properties. Accordingly, the grinding media selection is seen as an integral part of the mill design. Consideration of the requirement for classification is important in order to achieve the optimum mill and circuit performance. This can lead to the circuit feed not being classified for a steady feed with minimal slimes and a low size reduction ratio. Feed containing on-size particles would be deslimed by open circuit classification. Closed circuit classification is performed where the feed fluctuates. The rheological characteris­tics of the circuit feed slurry can have an influence on mill performance, and needs to be allowed for. A common misconception frequently encountered is the belief that "a mill is just a mill". This is not the case with stirred types of mills, since the operating parameters selected for the mill can have a large effect on the product characteristics. For example, horizontal shaft high speed stirred mills have a com­pletely different grinding action to vertical shaft low to medium speed stirred mills, which results in large differences between the surface area produced at a given product size (Liddell, 1986). Hence, it can be misleading to apply test results or design procedures obtained from one type of mill to other types for scale-up. The Metprotech stirred mill, as applied in the mining and minerals industries, is a low to medium speed vertical shaft mill. The basic design has been discussed previously (Liddell, 1989). Currently, the largest mills that have been manufactured have an installed power of 400 kW. The largest chamber volume at this power is 6000 litres, containing IO t of grinding media. It is intended that the installed power will increase up to lMW as applications requiring larger sizes arise.

Jan 1, 1995

By A. S. Azman

In collaboration with Kennametal Inc. and corry rubber corporation, the U.S. National Institute for Occupational Safety and Health (NIOSH) developed a drill bit isolator to address noise overexposures associated with roof bolting machines in underground coal mines. NIOSH laboratory studies confirmed that the drill bit isolator reduces noise during drilling. Field studies were needed to confirm that a noise reduction could be obtained under working conditions and that the device was sufficiently durable. This paper reports results of field tests of the device conducted at five underground coal mines. Noise reduction was assessed by comparing the operator?s noise exposure during drilling with and without the drill bit isolator. Durability was assessed by recording the number of holes and total feet drilled with each bit isolator until either the test period ended or the device failed. The results from these tests showed that the device is an effective noise control in a mine environment. The field-tested drill bit isolators provided a noise reduction of 3-5 db(A). Of nine devices tested for durability, five exceeded 610 m (2,000 ft) drilled and two exceeded 762 m (2,500 ft) drilled before failure. Durability issues found in the field tests led to final production optimizations that have resulted in a commercially available product for drilling with 35-mm- (1.3-in.-) diameter roof bits and hexagonal drill steels.

Jan 1, 2012

By M. Nambiar

Due to the remote locations of mining projects and the need for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short-circuit capacity. To cope with this situation, more and more mining operators are considering the installation of appropriately designed synchronous condensers together with power factor correction and harmonic filter systems (PFC & HFS). The installation of such power quality equipment is viewed as a technological advancement in the mining application. An adequate level of short-circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter-driven gearless mill drive systems (GMDs) used for grinding. This paper explores the impact, technical advantage and reasoning for the selection of this advanced hybrid technology to cope with the power system challenges of future mining projects. It also delves into the potential problems and how to address them.

By Ernest E. Thurlow

Introduction Today, more than 50% of rail-carried commodities are mineral industry related, with coal being the most important single commodity moved by rail. In 1980, coal accounted for more than 5.7 million of the total 22.6 million carloads moved by rail. Metallic ores were third behind grain, with more than 1.4 million carloads. Crushed stone, gravel, sand, and other non-metallic minerals totaled almost 2.3 million carloads. Chemicals and allied products, including fertilizer and coke, added another 1.7 million cars, with petroleum and petroleum products totaling 300,000 carloads. Coal Several things happened in the 1970s that gave rise to increased consumption of coal-particularly western coal-and to its dominant position among rail-carried commodities. First, the Clean Air Act of 1970 required generating plants to make significant reductions in sulfur dioxide emissions. To comply, utilities could either invest in scrubbers or switch to low-sulfur western coal. Many opted for the latter. By 1972, increasing demands by the utility companies halted what had been a 25-year decline in national coal consumption. Second, the Arab Oil Embargo of 1973 put an end to cheap oil and gas, limiting their future as fuels for electric generating purposes and increasing the potential for coal. Third, in 1977, President Carter announced an energy program with coal as its cornerstone, calling for an annual two-thirds increase in national coal production by 1985. He also called for conversion to coal by utilities and large industrial users. Finally, he proposed a 10-year, $10 billion program to encourage domestic coal production and stimulate development of export markets. Coal bounded into world prominence. Foreign demand for steam and metallurgical coal increased tremendously, while US demand for western coal also shot up. This meant greater demands on the transportation sectors that traditionally carried coal to market. Many railroads began programs to serve the coal industry. One example is Burlington Northern's commitment to handle increased western coal tonnages. The company spent more than $1 billion in recent years to develop a system capable of moving more than 91 Mt (100 million st) of coal each year. Other leaders in this renewal were Norfolk and Western, Union Pacific, Santa Fe, and Southern Pacific railways. The importance of the rapid growth of coal traffic to the railroads is shown in the accompanying table, which gives percentages of total tonnages hauled and revenues attributed to coal. With coal providing the railroad industry with a substantial share of its revenues, there is keen competition among the rail companies themselves and among railroads and other transportation sectors for coal haulage. But there is also cooperation when more than one railroad is involved in delivering the coal from mine to market or when a combination of transportation modes is more economical. The latter is represented by Conrail's interest in working with the port authorities of New York and New Jersey to establish a new coal port that would serve not only export markets, but also utilities and industries in the northeast. Iron Ore Next to coal, iron ore (taconite) is the most important single mineral commodity handled by railroads. In Minnesota, where most iron ore is produced, rail transportation is primarily by Burlington Northern and the Duluth, Missabe, & Iron Range Railway Co. (DM&IR). The DM&IR, owned by US Steel, serves several producers on the Mesabi Iron Range. Two of the larger producers, Erie Mining Co. and Reserve Mining Co., also own railroads that operate between the mines and the ports of Silver Bay and Taconite Harbor on Lake Superior. Several iron mines and taconite plants in Michigan are served by the Chicago and Northwestern, and the Soo Line. Total 1981 shipments of taconite and iron ore are estimated at 55.9 Mt (55 million It), compared with about 61 Mt (60 million It) in 1979 the most ever shipped in one year. Still, with annual production capacity of the eight Mesabi Range

Jan 10, 1982

By K. Chandrasekaran

Carbon-in-leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. The CIL process is becoming attractive even in other situations when preg robbing is not a factor. This article discusses the situations in which the CIL circuit can be applied. The results of leach-carbon-in-pulp (CIP) and CIL circuits at Newmont Gold's Mill No. 2, No. 4 and No. 5 are presented for comparison: Mill No. 4 was initially designed for a throughput of 4.1 kt/d (4500 stpd). It is presently operating at an average throughput of 6.6 kt/d (7300 stpd) without significant changes to the original design. The design considerations of the Mill No. 4 CIL circuit are discussed. The design of any processing facility represents a series of decisions. The final design options should ultimately be resolved based on economic as well as technical considerations. Every design decision represents some sort of compromise. From the designer's view point, these decisions are made with the conviction that the final product represents the most prudent long-term expenditure. The design throughput rate is a decision reflecting a maximum return for the capital and operating costs that the plant will incur over the life of the mineral resource. The result is a plant that is not operator proof or maintenance free because it would be too costly to build. At some point, the incremental increase in the level of capital expenditure would not adequately compensate for the lower

Jan 1, 1991

By Karl J. Benecke

Though the first patent on a bucket wheel excavator was granted in 1881 in the U.S. this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with the development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generating, despite the low heating value of German lignite in the order of 8500 kJ/kg (3600 BTU/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is in the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output open pit mines. The largest one, Fortuna Mine in the Cologne district, produced a, total of 45 000 000 t lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95 200 000 bank m3 equal to 200 000 000 t overburden had to be removed to accomplish this lignite output. The largest BWE (Fig. 1) ever built is working in the Fortuna Mine, too. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 t, its wheel diameter 21.6 m, as high as a 7-storey building.

Jan 1, 1977

By Steve Kral

"Gold rush" is usually associated the western United States - California, Nevada, and Colorado. The southeast section of the nation is known more for its rice, textiles, tobacco, indigo, and cotton. This area, though, is where it all began with gold in this country. The United States' first gold rush, in fact, is said to have started with the discovery of a 7.7-kg (17-1b) nugget in the Piedmont section of the Carolinas in 1799, some 50 years before the rush to California. The Carolina gold rush continued intermittently through 1942 when the Federal Government shut down all gold operations. Strong gold prices throughout the early part of this decade and new extractive technologies spurred a small resurgence of gold operations in South Carolina. Mind you, this is not Nevada with its flood of geologists and mining companies. Nor are there any 7.7 kg (17 lb) nuggets being discovered. But Ridgeway Mining Co., a joint venture between Kennecott Corp. and Galactic Resources, has set about mining 51 Mt (56 million st) of low-grade ore containing an estimated 43.5 t (1.4 million oz) of recoverable gold. The open pit, carbon-in-leach operation is located near the town of Ridgeway in South Carolina, about 32 km (20 miles) north of Columbia. Carolina gold North and east of Ridgeway, Piedmont Mining Co. operates the historic Haile gold mine near Kershaw, SC. And Brewer Mining Co. operates the nearby Brewer deposit. Between 1829 and 1942, South Carolina gold mines produced 10 t (318,800 oz) of gold. It all began in 1799 when Conrad Reed, son of a German immigrant farmer, found the 7.7 kg (17 lb) nugget in Little Meadow Creek, NC. His father thought the rock was worthless and used it as a doorstop, so the story goes. It took nearly three years before Conrad's father decided his doorstop was indeed gold. Gold was later discovered in the Greenville district of South Carolina. And, in 1828, Benjamin Haile discovered gold in a stream that ran through his property in Lancaster County, SC. Haile's mine became South Carolina's most famous and most productive gold mine, producing more than 7.8 t (250,000 oz). At first, miners worked the stream beds of Haile's property. Later, lode deposits were discovered on slopes alongside the creeks. They would lease 4.6 ml (50 sq ft) lots and mine as deep as 7.6 m (25 ft). During the Civil War, the Confeder-

Jan 1, 1989

By W. C. Morgan

This paper discusses some of the problems involved in predicting the productivity of a shovel and truck fleet in a new set of operating conditions. More specifically, it concentrates on the problems of predicting the travel times on the haul and return portions of the truck cycle under new profile conditions and the prediction of the interaction effect between the shovel and trucks at the loading point. The ability to calculate the travel times for a new road profile is not new. Additional corrections of these calculated times for expected actual operation can be made. In considering the interaction between the loader and the hauler, there are two approaches that can be taken. Probably the most accurate method of predicting the shovel-truck interaction is a simulation of the step-by-step operation considering the variation in cycle times of the shovel and trucks. This is usually called a stochastic simulation and requires input describing how these cycle times vary. However, by understanding the causes of this shovel-truck interaction it is possible to make sufficiently accurate predictions with much simpler methods. For the purpose of this discussion let us assume that the problem involves trying to predict the productivity of a single shovel-truck fleet at some future time in an existing operation. Let us also assume for simplification that the new operation to be simulated has the same loading and pit conditions and the same dumping conditions as did the existing operation. Therefore, the only difference would be the difference in the hauling profile for the new operation. The problem then becomes one of predicting the change in the travel times on the haul and return portions of the cycle, and in determining the change in interaction between the shovel and trucks with the new truck cycle times.

Jan 1, 1968

By L. M. Gochioco

The Seismic Interactive Interpretation Workstation (IIW) integrates various sets of geophysical and geological data to form a network of information which is stored in a database. Computer models are generated from known drillhole information and later correlated with the processed seismic data. Seismic color processing adds another dimension to the interpretation process. Complex trace attributes provide better definition of subtle features not easily observed from black and white sections. Utilizing the computer workstation, the explorationist gains valuable insight and conducts more intelligent interpretation of seismic data through a more comprehensive network of data analysis.

Jan 1, 1989

By B. Listerud, G. Zhan, M. A. Jones

Barrick Goldstrike Mines Inc. (BGMI) operates the Betze-Post openpit and the Meikle and Rodeo underground mines. Because the majority of the orebody is located below the water table, mining at BGMI requires a significant dewatering program. BGMI has a comprehensive dewatering and water management system that experienced a peak dewatering rate of 4,400 L/s in the mid 1990s. Changes to the hydrologic/hydrogeologic system caused by the mine dewatering have been monitored by an extensive network of groundwater monitoring wells and surface water monitoring stations, which cover about 1,550 km2. In addition to the monitoring program, a new tool, called Interferometric Synthetic Aperture Radar (InSAR), has also been used to enhance the evaluation of changes. Finally, a groundwater flow model has been developed that successfully simulates and predicts aquifer responses in the mine area and region. The well-calibrated flow model has served as a reliable tool to develop dewatering and mining plans, and project post-closure hydrologic conditions in the region. This paper introduces the BGMI dewatering and water management system and the means used by BGMI to evaluate and anticipate hydrologic responses in the region. The water management and analysis system has been and continues to be an integral part of managing ongoing operations, planning and pricing out future activities and evaluating the long-term effects of mine water handling.

Jan 1, 2011

Caterpillar and Fortescue Metals Group have moved forward with the delivery, installation and support of a complete Cat MineStar System at Fortescue?s Solomon iron ore mine in the Pilbara region of Western Australia. The complete technology suite was implemented for the first phase of Solomon, the 20 Mt/a (22 million stpy) Firetail manned mine, in October 2012. As part of an autonomous mining solution for phase two, the 40-Mt/a (44-million stpy) Kings Mine, eight Command for hauling Cat 793F CMD trucks were commissioned and commenced operations in the second quarter of 2013. The mine plan calls for a progressive ramp up to 45 autonomous trucks during the next several years. In addition, other Cat MineStar System capability sets, Fleet, Terrain, Detect and Health, are being used across the mobile equipment fleet, including support equipment and light vehicles. Working closely with Fortescue and its mining contractor, Leighton Contractors, Caterpillar and the Cat dealer in Western Australia, WesTrac, are providing a full solution for managing, operating and supporting Cat MineStar System and Command for hauling. The greenfield Solomon Mine has brought together the skilled team from Caterpillar, Fortescue, Leighton Contractors and WesTrac to deliver an efficient, cost effective autonomous mining solution.

Nov 1, 2013

By Thomas D. Henderson, Wayne R. Hopkins, Arthur Lynch

Brought on stream in 1975, the 10,000-tpd copper oxide processing plant of Anamax Mining Co. at Twin Buttes, Ariz., is now at design capacity. Based on acid agitation leaching, solvent ion exchange, and electrowinning, the Anamax plant bridges an ore to metal gap by producing mine site copper cathodes from lime-bearing oxidized feed. Until recently, such material was considered submarginal because copper recovery was uneconomic using conventional methods. The new Twin Buttes oxide plant, the largest of its kind in North America, is one stage in the expansion of Anamax, a joint venture owned equally by The Anaconda Co. and Amax Inc. Other phases include an accelerated stripping program in the pit, an expansion of the sulfide concentrator from 32,000 to 40,000 tpd, and construction of a 57 MW diesel generating station for the oxide plant. Once the basic oxide flowsheet had been selected, Anamax awarded a contract to a joint venture of Arthur G. McKee and Co.' (Western Knapp Engineering Div.) and Davy Powergas' (a member of the Davy International group). The contract covered process design, engi¬neering, procurement, and construction. The property, identified by Banner Mining Co. in the 1950s and developed by Anaconda, was put into production in 1965 as an open pit mine equipped with a 32,000-tpd sulfide flotation concentrator. The Twin Buttes mine has since become one of the largest earth¬moving operations in the world, excavating some 10 tons of waste per ton of ore. At the original sulfide mill feed rate, the mining fleet moved 375,000 tpd of material (225,000 tpd alluvium and 150,000 tpd of rock). The most significant copper mineral in the ore body is chalcopyrite, which is scattered in pockets of weak mineralization. Cap oxidation has progressed to depths of several hundred feet, principally as chryso¬colla. Present estimates place minable reserves at 347 million tons of sulfide ore grading 0.6% copper and 55 million tons of oxide ore grading 0.9% recoverable copper from 1.25% total copper. The nonre¬coverable fraction is composed of native copper and insoluble copper oxides and sulfides. The oxide ore has been partially stripped, and 25 million tons having a copper content greater than 0.6% have been stockpiled. The stripping of oxide ore to expose sulfides will continue for several years. The copper oxide studies launched by Banner Mining in the 1950s were continued by Anaconda. Process routes investigated included: acid leaching; cyanide leaching; segregation roasting; chlorination, oxidation, and reduction; flotation in combination with leaching; cal¬cite flotation plus leaching; copper oxide flotation; and sulfidization flotation. By late 1968 test work favored a low temperature roast followed by an ammonia-ammonium carbonate leach of the ore. During this period, acid leaching had been discounted because of excessive con¬sumption of expensive acid by the high limestone ore matrix. Restric¬tive SO2 emission controls in 1971 suggested an increase in acid production and availability at a lower cost. Research then switched to acid leaching, resulting in development of the present flowsheet. Mechanically agitated leaching in a cascaded series of tanks was selected in preference to vat leaching after piloting a stirred-tank system. Preliminary testing of vat leaching indicated that inter-vat solution clarification problems could be caused by gas evolution from leaching of high limestone ore. Lack of research time for resolution of this problem, plus success of the pilot agitation system, dictated the final flowsheet selection. In 1973 Anamax decided to proceed with agitation acid leaching to produce liquor for a solvent ion exchange (SIX) and electrowinning (EW) installation. At that time, such systems were proving their eco¬nomic viability, and they allowed direct recovery of high quality cath odes while bypassing the smelting and refining of lower grade cement copper precipitates. The Anamax oxide plant processes a grade of about 1% recovera¬ble copper from stockpiled sources and new mine production. Unit operations include size reduction, agitation leaching, countercurrent decantation washing of residue, pH adjustment of solution, clarifica¬tion, solvent ion exchange, and electrowinning of copper, with a mini¬mum of environmental impact. The feed to the primary crushers is composed of: 1) -10-in. stockpiled oxide ore, which has passed through the mine crusher and has been grade-segregated to allow blending for a consistent feed material. 2) -4-ft ROM oxide ore stockpiled in the early mining operation. 3) -10-in. ore currently being mined. Ore is delivered in 100-ton mine trucks to a dump pocket, where an apron feeder transfers the ore to an inclined 6-in. fixed grizzly. The grizzly oversize passes through a 48 x 60-in. primary jaw crusher, where it is reduced to -6 in. The fixed grizzly undersize and the crusher product are conveyed to a 4-in. vibrating grizzly. Oversize from this grizzly reports to a 7-ft Standard cone crusher, where it is reduced to -1 in. The crusher product and the vibrating grizzly undersize are conveyed to two 8 x 20-ft double-deck vibrating screens that operate in closed circuit with two 7-ft short head cone crushers. Screen undersize (-1/2 in.) is delivered to a covered conical fine ore stockpile with a designed live capacity of 15,000 st. Beneath the stockpile are ten Pioche belt feeders feeding two conveyor belts that supply the milling circuits. Each group of five feeders has two variable speed and three fixed speed drives. Grinding to 95% -48 mesh is done in two parallel lines, each consisting of an 111/1 x 18S -ft rod mill and a 12' x 30-ft ball mill in open circuit. Water is added to maintain a pulp density of 72% solids in the mills. Further water additions are made to the ball mill discharge sumps to create a 60% solids slurry for transfer to the leaching reactors. The nominal grinding rate is 440 tph solids. A splitter box on the product from the mills separates the incoming slurry into two streams, one for the leaching reactors and the other for the pH adjustment reactors. This split is determined by the lime content of the feed material and the pH of solution entering the pH adjustment reactors. Five 30-ft diam by 31-ft high mechanically agitated, rubber-lined leach tanks are arranged in cascade, with gravity transfer from one to another by enclosed launders. Concentrated sulfuric acid (93.2%) from storage is added to the pulp principally at the first leach tank, and the reacted slurry leaving the cascade after a 5-hr residence time at 50% solids is pumped to countercurrent decantation (CCD) wash thickeners.' At this point, most of the soluble copper has been leached from the ore. Up to 250 lb of sulfuric acid is consumed per ton of ore, the acid being supplied in tank cars from a nearby smelter. Leached slurry at 50% solids is washed countercurrently with return raffinate from the SIX plant in a series of four Doff-Oliver center caisson, 400-ft diam thickeners. Solids advance from thickeners No. I through No. 4 to the tailings dam. SIX raffinate advances from thickener No. 4 to thickener No. l, where a pregnant solution overflows to pH adjustment. To optimize solvent extraction, the pH of the pregnant solution from CCD thickener No. I is adjusted from 1.5 to 2.5 by adding unreacted ground slurry (split from the grinding circuit) to the preg¬nant overflow of No. I CCD thickener. The resulting slurry is retained for 45 min in three mechanically agitated leach tanks. CO, generated during leach and pH adjustment is ducted to a demister, where entrained acid droplets are removed. The cleaned CO, and the No. 4 CCD underflow are the only effluents from the plant. The underflow of No. 4 thickener mixes with tailings from the sulfide concentrator and is neutralized. Slurry exits the pH adjustment vessels at about 10% solids and

Jan 1, 1985

By Tan Zhenxiang

INTRODUCTION Koolyanobbing is an open cut iron ore mine, which is located in Yilgarn region of Western Australia. To prevent the operators from suffering silicosis diseases and protect the air from being polluted, a series of dust control measures have been taken. These measures include ventilation and dust control system for sample preparation shed, dust collecting system for drill rig, dust suppression system for ore processing plant, dust control for haul road. The details related to individual dust control measure are dealt as follows. SAMPLE PREPARATION SHED DUST CONTROL The sample preparation is one of the major dust sources at Koolyanobbing. The activity is being carried out at the sample preparation shed. It typically needs to go through the following stages, that is, crushing, splitting, drying and pulverising. The amount of dust generated from crushing and splitting is mainly determined by the moisture content contained in the pre- pared sample. A significant amount of dust is generated at the sample pulverising stage due to cleaning sample bowl with com- pressed air. To protect the sample preparing personnel's health and make the dust level in the air meet the requirement from the health and safety authority, a central ventilation and dust control system has been installed at the sample preparation shed. As shown in Fig. l, the system consists of suction heads, suction lines, dust collector and vacuum fan. The fan creates vacuum environment in the system, therefore the dust is drawn into the dust collector through the suction heads and suction lines. The dust collector is of fabric filter. When the dusty air comes to the filter, the dust in the air is collected and retained on the surface of the filter while the clean air passes through and enters the atmosphere. The retained dust is blowed out by the pressured air pulses and deposits into the dust bin underneath the filter. A time relay device is used to control the cleaning time and the cleaning interval. DRILL RIG DUST CONTROL A hydraulic percussion drill is used to drill blast holes. To carry out the drilling operation properly and efficiently, the cut- tings are being flushed out of the hole by the compressed air. In order to prevent from the fine particles in the cuttings escaping to the air, a dust collector is attached to the drill. The collector mainly consists of suction head, cyclone and bag filter. Refer to Fig. 2. The suction head is installed at the lower end of the feed beams and is movable. The moving range is up to 250 mm. It is not only used to restrict the cuttings, but also used to prevent water from entering the filters when drilling wet hole. A 406 mm diameter primary cyclone is used to separate the heaviest particles in the cuttings. It is also used as blast holes sampling equipment. One part of the dust particles are collected by a sample bag through a splitter attached to the end of the cy- clone. The rest of the particles fall down to the ground through the closing rubber. The bag filter is driven by a hydraulic motor (1). It is used to collect the lighter particles in the cuttings. The filtering area is 16 m2 and the dust separation efficiency is up to 99.9%. The working principle of the filter is demonstrated in Fig. 3. When the rock drill (9) flushing is turned on, the pressurised air from the compressor is directed to the rock drill and to the pres- sure switch (10). The pressured air will open the pressure switch to de-energise and close the solenoid valve (4) The pressure affecting the cut-off cylinder (5) keeps the exhaust port flap open. When the flushing valve (8) is closed, the pressure affecting the cut-off cylinder disappears and the internal intake opening flap is closed by a spring. The pressure also ceases to affect the pressure switch and the spring switches the contact to the point 2. The time relay (11) is now activated and gives a 0.5 second current impulse to the solenoid valve and keeps the current cut off for approx 8 seconds. When the solenoid valve is live, it opens and lets an impulse of pressured air to the filters (2). These impulses will clean the filters.

Jan 1, 1997

By Dennis D. Fischer

The second underground coal gasification experiment conducted by ERDA's Laramie Energy Research Center at a site near Hanna, Wyoming, was completed on July 30, 1976. During the experiment production reached 0.32 Mm 3/d (12 Mft3/d) of 6.9 MJ/m3 gas (175 Btu/ft 3 ). Approximately 6100 tonne (6700 ton) of coal were gasified during the experiment. Energy return ratios of 4.5 to 5.3, cold gas - thermal efficiencies of 76 to 89 percent, and overall process efficiencies of 65 to 74 percent were achieved during the second Hanna experiment. This paper describes the experiment and the results obtained with emphasis given to the determination of the energy recovered relative to energy consumed in conducting the test. Data from this determination are compared with previously published data from the first test conducted at Hanna during 1973-1974.

Jan 1, 1977

By Chester R. McKee, Amar C. Bumb, Kohei Kawakita

Unlike many other heavy metals, gold can be profitably mined in small operations because of the prices. One mining technique that seems ideally suited for small deposits of gold and for certain large, lowgrade oxidized disseminated deposits is solution mining. Solution mining generally requires lower capital investment and operating costs than conventional mining and milling and is safer and less degrading to the environment. Although gold has long been recovered by cyanide leaching following conventional milling, solution mining as discussed here gained momentum only in the past two decades, during which time alternative lixiviants instead of cyanide have been researched. Chamberlain and Pojar (1981) classified solution mining systems used today as three types, namely heap, dump, and in-situ leaching.

Jan 1, 1990

ShouSteel Mining Ltd., a subsidiary of ShouSteel (Group) Co., was founded in 1959 and is located in QianAn City in Hebei Province, China. ShouSteel?s pelletizing plant uses iron ore as a raw material combined with limestone, dolostone, or olivine, with bentonite as a binder. After mixing the raw materials and forming them into small, spherical balls, ShouSteel then fires pellets in kilns for hardening. The company sells the finished pellets as raw materials for blast furnaces used to produce industrial metals such as iron. ShouSteel?s handling capacity is approximately 24.5 Mt/a (27 million stpy) of ore. The company?s production capacity is 3.2 Mt/a (3.5 million stpy) of oxide pellets and 560 Mt (650 million st) of sinters. Until recently, ShouSteel Mining had not replaced its electronic scales in its series of ingredient chambers. Because of the wear and tear on these older scales, the weighing system began to encounter regular problems. The company experienced a high failure rate from the integrator, an unstable signal, weak anti-interference ability and low accuracy. ShouSteel also found that spare parts required during repairs were consistently high in cost and that system calibration was becoming increasingly frequent.

Jan 1, 2012