Search Documents

By W. R. Reed

NIOSH continues to conduct respirable dust control research for surface mine blasthole drilling operations. Research areas have included testing variables (shroud leakage area, drill deck cross-sectional area, shroud height, collector-to-bailing airflow ratio, etc.) that have the most impact on respirable dust control, development of a dust collector inlet hood, development of a dust collector dump point shroud, and testing of a small diameter water separating sub. This paper summarizes the results of the aforementioned research that has been completed. Additionally, past dust control research for drilling operations of both underground and surface mines completed by the U.S. Bureau of Mines, created in 1910 and incorporated into NIOSH in 1997, is reviewed.

Jan 1, 2008

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite (Bayer Process) is known as red mud. Approximately one ton of red mud is produced for every two tons of bauxite mined. The red mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that more than 90% (by weight) alumina can be recovered from red mud by soda ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of more than 94%, resulting in attempts, for magnetic separation. These separations are desirable because there are no waste products generated. Consequently, there is an opportunity for complete utilization of the waste material. Conversely, the preseparated material could be charged through the tuyeres in an iron blast furnace, or it could be smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag would be high enough to justify its recovery by an established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red mud as an alternative to direct-reduced iron (DRI) is also discussed. A critical assessment of the recovery sequence chosen for the products is described based on economics. Key words: Red mud, Waste product utilization, Alumina recovery, Titanium oxide, Iron

Jan 1, 2003

By F. Daviess

A requirement for geological controls during orebody modeling results from the recognition of heterogeneous geological characteristics and/or abrupt variations in orebody geometries. While purely statistical methods are often sufficient for modeling uniform homogeneous deposits, and the only recourse for many that are extremely complex, geological interpretations can be extremely valuable as controls during the modeling process. The advent of relatively inexpensive, sophisticated graphical computer hardware and software has focused considerable attention on the three dimensional visualization capabilities now available to the mining industry. Orebody geometries can be easily imported into many systems as wireframe or solid models, rendered with shading and color, rotated in space, exploded into composite parts, zoomed into and otherwise displayed to awe any audience. The requirements for an initially meaningful, accurate, geological interpretation are sometimes lost when the focus is on an apparently complex, highly resolved end product. Details of the initial data and sensitivities of modeling assumptions are not always sufficiently scrutinized. Software capabilities have extended the geopoetic license into three dimensions. The new tools, while greatly facilitating model construction and rendering, have done little to expedite basic data preparation and analysis. This paper attempts to briefly summarize the purpose and method of the construction of geological controls. The examples selected are from wire­framing and block modeling; application software processes commonly used in the mining industry today.

Jan 1, 1992

By Dae S. Young, Steven F. Hoerger

The geostatistical method of indicator kriging (IK) was extended to analyze two-dimensional distributions of rock joint orientations. The IK method provides a non-parametric approach for spatial analysis of local probability distribu- tions. By taking into account the spatial correlation of rock joint outcomes and the relative geometry between estimation unit and samples, the IK method provides optimum, spatially conditioned estimates. The estimation method was tested by comparing distributions of actual mapped rock joint orientations with their corresponding kriged estimates. The comparisons show the unbiasedness and accuracy of the non-parametric approach for estimating local probability distributions.

Jan 1, 1986

By Edward J. Karkoska

The film you see is a slow motion view of a typical half million ton taconite blast at one of Erie's mines. This blast is made up of 220 drill holes and a total of 325 thousand pounds of blasting agent. The second view of the same shot is taken by a remote control hi speed camera located 1500' directly in front of the blast. Shortly you will see some violent camera movement as the air blast shock wave strikes the camera location. As the blasting sequence progresses the rock fly becomes evident, and if you will look closely amidst the clouds of smoke, rock fragments weighing up to 1/2 ton begin to cascade into view. These missles are the chief concern of blast security. The next camera shot at 4000 frames/second vividly describes the primacord firing lines detonating the blast. Travelling at 22,000 ft./sec., this white snake of fire travels to each hole, detonating the blasting agent. Before we get into the matter of blast security, let me locate our operation for those of you not acquainted with Minnesota's iron ranges and tell you something about our company.

Jan 1, 1969

By Ricardo Gomez, C. T. Ogryzlo, A. A. Dor

This paper reviews the historical background leading to the development of the project. It gives a description of the exploration program and resulting geological and ore reserve information together with plans for mining. A discussion is included of the three processes investigated for the project: 1. Rotary Hearth and Magnetic Concentration 2. Shaft Furnace and Electric Furnace 3. Rotary Kiln and Electric Furnace Results of pilot plant campaigns conducted at Fiskaa, Norway, and Riddle, Oregon, on the process chosen for the production of ferronickel are presented. The paper continues with a review of the considerations involved in selection of commercial plant equipment and concludes with comments on the current status of the project.

Jan 1, 1979

By M. Morrongiello

The Kalgoorlie Consolidated Gold Mines Fimiston Open Pit is mining through a dense network of disused level workings and stopes of varied sizes and orientations. This study investigated the interaction between underground workings and the pit slope stability, in particular for the ultimate pit depth of over 600 metres. Parametric analyses were conducted on the structural and rock mass properties in order to provide realistic input. Several cases in both 2D and pseudo 3D using UDEC were modeled and analyzed to investigate the performance of the rock mass at various mining stages. The concept of equivalent property factor was also introduced to model the 3D behavior using 2D models. Based on the modelling results, the possible failure mechanisms and deformation of the pit walls were assessed. Factors of safety have been derived for the pit slope at different mining stages using the strength reduction technique. The modelling results agree well with pit performance monitoring results to date. The concept and results presented in this paper could be a useful reference for operations with similar circumstances and stress regimes.

Jan 1, 2005

By Brendan Howard

Rio Tinto has a large globally distributed technical workforce and needs to ensure these employees have the requisite skills to not only manage technical risk and enable safe efficient production, but also ensure they are keeping pace with a fast-changing technological landscape. Traditional approaches to learning struggle for scale and an inability to respond to the extreme diversity of capability development needs. In response, Rio Tinto has successfully introduced innovative approaches to learning and employee engagement via leveraging the power of globally distributed networks for peer-to-peer knowledge transfer and providing mechanisms to recognise, reward and retain the individual technical contributors.

Feb 1, 2024

By F. L. Wilke

The prototype of an expert system, designed to assist layout planning of face operations, is presented. By specific combination of knowledge-based and conventional EDP techniques it has been possible to extend the known Kepner-Tregoe method up to the determination of mature layout solutions in difficult planning cases. It has been proven that the presented strategy - which can be applied to any kind of problem with similar structure - is apt to provide efficient EDP support for handling complex mining problems. Such support goes far beyond the purely numeric evaluation of envisaged alternatives.

Jan 1, 1989

By B. M. Kunar, C. S. N. Murthy, B. Rao K

Rock particle size has a very important significance in the mining industry, starting from blasting till the mineral processing. The present study was carried out to understand the particle size distribution in various sieves after conducting the ball milling process. The time of the grinding process was varied at different intervals. It was observed that 80% of the particles of both granite and marble rock samples passed through the 4800 μm sieve when subjected to grinding time of 40 minutes. Also, it was observed the number of particles that were retained in the smallest sieve of <75 μm was higher in the case of granite sample when compared to a marble sample. INTRODUCTION India is a major exporter of granite and marble stones. The major use of marbles and granites are constructing walls and floors. There are several machining processes that are applied before it is used as floors and walls. During this process, wastes are produced these wastes are used in various ways. These include use of powders for clay products (Segadães, Carvalho, & Acchar, 2005), as an additive in cement production (Aruntaş, Gürü, Dayi, & Tekin, 2010), to enhance the properties of brick ceramics (Saboya, Xavier, & Alexandre, 2007), in constructing bricks (Bilgin et al., 2012) and as an additive in concretes (Aliabdo, Abd Elmoaty, & Auda, 2014). Usually, the powder form of marble and granites are used as an additive in the above-mentioned applications. Powders of marble and granite are obtained through the grinding process. One such process of grinding is the ball milling process. In the ball milling process, a quantity of samples along with the charge quantity consisting of steel ball is subjected to a grinding process within a closed chamber as shown in Fig. 1. An even particle size can be obtained through sieving the material after subjecting it to grinding. The present study is planned to understand the particle size distribution in various sieves due to varying time and charge quantity in the experiment. Only time was varied to understand the amount of particle distribution in the case of granite and marble rock samples and a comparison is drawn. A statistical model was developed for marble rock specimen considering the data obtained by varying time and charge quantity in the ball mill experiment.

Jan 1, 2019

By F. Milton Lewis

In this paper an attempt has been made to review the cost trends in producing copper by conventional milling. smelting and hydro-metallurgical means during the last five years. The primary objectives of this cost analysis are to provide a base for future projections as well as to indicate which cost items are more volatile in their influence on overall cost of producing copper.

Jan 1, 1977

By I. Melik-Gaykazov, N. N. Melnikov, V. A. Fokin, S. P. Reshetnyak

Kola Mining Institute has been carrying out investigations of the possibility to steepen the walls of the Kovdor open pit with the design depth of 600 m. Steeping (up to 60°) wall angles is done by double height (24 and 30 m) benches with vertical slopes. One of the safety factors of mining with such walls is choosing the width of the safety berms preventing against rock falling from the slopes into the pit working area. The test on rock falling from 24 m benches has shown that vertical slopes are not more dangerous compared to the inclined(60-75°) ones.

Jan 1, 2003

By CLAIRE STREBINGER, ADITYA JUGANDA, JURGEN F. BRUNE, GREGORY E. BOGIN JR.

Methane gas explosions are a major risk in underground coal mining operations. The severity of such explosions can range from local area damage to massive loss of miners’ lives along with significant damage to mine infrastructure and ventilation controls that may lead to mine closure and loss of the entire operation. This study demonstrates the viability of integrating a computational fluid dynamics (CFD) combustion model into a longwall mine ventilation model to simulate methane gas explosions in the longwall face area. The resulting 3D methane gas explosion simulation can provide better understanding of the fundamental physics and the potential impact of an explosion in an underground longwall coal mine.

Aug 1, 2022

By L. Alagha, F. Schott, M. B. Haya, Z. Xiao, K. C. Monyake

"Froth flotation is a process in which valuable minerals are separated from gangue minerals on the basis of surface wettabilities. It is a universally accepted process for the beneficiation of coal. The large amount of coal fines that have been generated from both mining and beneficiation processes has been reported as a chronic problem to both fine coal preparation and utilization as these fines contain a high amount of ash forming minerals. The current study investigated the potential application of Synthetic Bio-compatible Polymers as slime depressants in fine coal flotation for the possibility to enhance the combustible recovery and ash rejection. Raw coal samples containing 21% of ash-forming minerals were crushed, grinded and floated in the presence of Chitosan polymer. Flotation tests were carried out in D-12 Denver flotation cell with 1-Liter capacity. Flotation outcomes were studied as a function of polymer concentration. Box-Behnken factorial method was used for experimental design. Second order response functions were produced for ash% and combustible recovery. The results obtained from this study demonstrated positive influence of chitosan polymer on ash% and combustible recovery. Ash % was decreased by 3.32 % while an increase of 48.15 % in combustible recovery was observed when chitosan was introduced in the flotation process. INTRODUCTION Froth flotation is a widely used method of separating minerals by utilizing the difference between surface wettabilities [1], [2].Modern mechanized mining and ore handling operations produce large amounts of coal fines which in the past were not processed but discarded as waste[3]. Even though flotation is the best method of beneficiation for coal, it can be challenging in case of fine coals. In fine coals, slime coatings of colloidal mineral matter exist on the coal surface. These coatings render the coal hydrophilic, hence reducing flotation efficiency and recovery. Of late, different researches have been using biodegradable polymers to determine their feasibility in enhancing fine coal flotation efficiency[4].Naturally occurring and synthetic polymers, for example, polyacrylamide-based polymers, have been widely used in flotation as multifunctional reagents[5],[6],[7]. Hybrid polyacrylamide polymer has been successfully used as a depressant for ash forming minerals in fine coal flotation[3]. Recently, chitosan has been successfully used in flocculating quartz particles to produce faster settling rates of fine tailings [4]."

Jan 1, 2018

For all the attention given to mining activities in Central and South America, Mexico, Indonesia and Papua New Guinea, it is sometimes easy to forget the activities taking place in one of North America&apos;s most important and largely untapped regions -Alaska. The Alaskan minerals industry employed about 3,406 people during 1995. That is a 23% increase from - - 1994. It also contributed about $719.8 million to the state&apos;s economy during 1995, a 10% increase. During the past few years, Alaska has seen significant increases in exploration and mining activity. Fairbanks Mining, an arm of Cyprus Amax, began producing gold during 1996 at its Fort Knox Mine, as did Nevada Goldfields&apos; Nixon Fork gold mine. Kennecott&apos;s Greens Creek lead-silver-gold mine also reopened and USMX began operations at its Illinois Creek gold mine. In addition, several impressive exploration projects were under way in Alaska. Placer Dome reported good results at Donlin Creek project in southwest Alaska. Likewise, Newmont Exploration is getting serious about its True North gold project. And Nerox is nearing production at its Jonesville coal project in Alaska&apos;s interior. In November, about 400 miners gathered in Anchor- age for the Alaska Miners Convention. Throughout the conference and exhibition, attendees listened to updates on these precious- and base-metal and coal exploration and mining operations. They also learned that the state wants more miners to head north and help develop its natural resources. Alaska is ripe for a smelter The mining industry -Alaska&apos;s miners in particular - has a powerful ally in Sen. Frank Murkowski (R-AK). He is the chairman of the Senate Energy and Natural Resources Committee. During his luncheon address, Murkowski said it appears that it is economically feasible to extend the Alaska Railroad to northwest Alaska, taking advantage of the large coal and hard-rock mineral tracts in the Ambler mining district. He also renewed his push for building a major smelter in Alaska to process ore that would come from the Ambler mining district. Murkowski believes that Alaska&apos;s economy can be expanded by extending the railroad from Nenana to the Point Lay coal fields to open coal development. Along the way, the railroad would pass through the Ambler district, helping to develop the hard-rock deposits. An outgrowth of this additional mineral development, Murkowski said, could be a new smelter in Alaska. It could use power from the Tyee hydroelectric facility near Wrangell or from the Makushin geothermal project near Unalaska. Either site, he added, offers access to plentiful, relatively low-cost power, at tidewater to facilitate ore deliveries to the Pacific Rim. The Congressional Research Service has determined that there are enough mineral deposits and coal beds to make it possible to finance the extended railroad, he said. The 1,200-km (744- mile) rail extension would cost about $4.2 billion. The North Slope of Alaska contains up to 3.6 Tt (4 trillion st) of coal, Murkowski said, that contains less than 0.25% of sulfur and less than 4% moisture. It aver- ages 12,300 Btu in heat content. "That is a tremendous resource," he said. The Ambler mining district, meanwhile, has at least eight identifiable hard-rock deposits, Murkowski continued. These contain zinc, lead, copper, nickel, chromium, tin, barite, gold and silver. "All eight of these can generate ore concentrates at rates similar to Red Dog&apos;s cur- rent 725 ktla (800,000 stpy)" of zinc, he said.

Jan 1, 1997

By E. R. DeMen

In late 1965 General Mills announced the availability of a new liquid ion exchange reagent, LIX®-64, for the recovery of copper from various solutions, such as dump leach liquors. Acceptance of this material by the copper industry has been gratifying. A number of pilot plants have been operated, and at this writing there are four commercial plants either in operation or under construction. The properties and operating characteristics of this reagent have been described in previous papers.1,2 LIX-64 is quite effective and selective for copper extractions although partially limited in pH ranges, losing extraction efficiency as the acidity of the feed solution increases to below pH 1.0. Also, the LIX-64 content in the kerosine carrier was limited to about 10 volume percent (except for special cases) because of rapidly decreasing phase disengagement rates above this content. This in turn led to large plant capital costs, as the organic flow rates had to be in- creased (rather than LIX-64 content) to extract the copper from high content liquors. This was true in all circuits where the feed copper content ran above 2.0 g/l copper. A reagent was needed which would extract copper from more acidic liquors (or higher copper content liquors) and which exhibited improved phase disengagement characteristics with reagent contents up to 30 volume percent. General Mills is pleased to announce the availability in commercial quantities of a new and improved reagent, L+-64~. This reagent broadens the pH range in which copper can be extracted, and exhibits superior phase disengagement characteristics. The improvement in the reagent has been noted in laboratory circuits, as well as pilot plant runs and commercial operations.

Jan 1, 1970

By K. A. Natarajan

The utility of yeast, Saccharomyces cerevisiae, in the separation of quartz from hematite is demonstrated. Yeast cells, as well as their metabolites, functioned as flotation collectors, depressants or flocculants and dispersants for hematite and quartz. Interaction between yeast and the above minerals resulted in significant surface chemical changes, rendering quartz surfaces hydrophobic and hematite hydrophilic. Mineral-specific extracellular proteins and exopolysaccharides were secreted by yeast cells when grown in the presence of quartz and hematite, respectively. Quartz could be efficiently separated from hematite through microbially induced flotation and selective flocculation.

May 1, 2012

By E. B. Fitch, D. A. Dahlstrom

Liquid-solids separation is common to practically all mineral and coal processing as the bulk of beneficiation plants employ water as the major processing vehicle. The growing usage of hydrometallurgy has increased the importance of liquid-solid separation as acidic and basic solutions result in greater amounts of colloidal solids, with their consequent greater difficulty of separation, the economic need for chemical recovery to minimize this operating cost, and the usual necessity of employing more costly construction materials. The three processing steps covered in this section have significant capital costs. Drying, particularly, has an important operating cost because of the obvious need for energy to evaporate the water or solvent. Several common factors influence all three liquid-solid separation steps. Particle Size and Size Distribution. In general, finer particles have slower settling and filtration rates. The specific surface area is increased, which means a lower solids concentration in the thickener underflow and discharged filter cake as well as a grater moisture content to be evaporated in the drying step. Therefore, overgrinding or excessive attrition should be avoided. Consideration should be given to optimum particle size consistent with entire plant operation performance and recovery. Solids Concentration. Increased feed solids concentration will generally minimize required equipment size and costs in all three liquid-solid separation steps. Most thickeners are designed on the basis of unit area required, expressed as square feet per short ton of dry solids per day (square meters per metric ton per day) which will usually decrease with increased feed solids concentration. Filtration rates also increase as the required flow through the capillaries of the filter cake decreases. Dryer capacity increases and less energy per ton of final product is required to evaporate the associated moisture. Particle Shape and Surface Characteristics. Generally, optimum shape is a spherical particle of zero porosity. As either of these factors degrade away from the desired state, difficulty increases. This is particularly true in drying, where porosity can decrease drying rate significantly if the moisture must first reach the particle surface by diffusion

Jan 1, 1985

By M. A. Trevits

The explosion hazard presented by methane gas in coal is confronted daily in the mining industry. Research has developed several viable methods for gas control in addition to conventional dilution by ventilation. Such methods include the drilling of horizontal or cross-measure boreholes from a mine opening and vertical boreholes hydraulically stimulated in advance of mining or for gob gas drainage. The long-term production history of five gas drainage installations was studied. Three installations were completed in the Pittsburgh Coalbed: two in West Virginia and one in Pennsylvania. The remaining installations were completed in the Mary Lee Coalbed in Alabama and the Sunnyside Coalbed in Utah. The types of drainage methods utilized included horizontal and vertical boreholes. The length of production studied ranged from 860 days to 36 years. The cumulative production from the five sites was in excess of 155 Mm3, representing a significant volume of gas.

Jan 1, 1985

By Raymond L. Zahradnik

Marco Polo reported that the Chinese used "black rocks" for fuel, and recent studies indicate that the Chinese may have used coal in small amounts for two or three millennia previously. The use of coal as a major source of energy however, did not begin until about the twelfth century, when the inhabitants of the northeast coast of England discovered that certain black rocks found along the seashore--and thereafter known as "sea soles" would burn. Since this initial discovery, coal has been mined continuously, first in England and shortly thereafter in present Belgium, France, and Western Germany, and finally in all coal-bearing areas of the world, in ever increasing amounts. The production of coal in the United States began about 1820, when 14 tons were reportedly mined. Since that time the production of coal increased steadily until about 1907, after which the rate has fluctuated between the extremes of about 400 and 700 million tons per year. Bituminous coal and lignite production was 590 million tons in 1974. Value of production was $8. 9 billion. Anthracite production was b.3 million tons with a value of $157.5 million.

Jan 1, 1975