Search Documents

By K. L. Woodruff

Shredding is the usual first step in processing municipal solid waste (MSW) for resource recovery. This unit process requires high capital cost and, usually, considerable maintenance cost. In addition, some shredders at times will render certain components of the MSW in a form difficult to recover. This is particularly true in the way metal cans are distorted and the way glass is pulverized. A trommel screen was proposed (1) to pre-process packer truck refuse prior to shredding. Part of the logic for this step is that the portion of raw refuse already within the specified shredder output particle size range would bypass the primary shredder and proceed directly to further processing, such as to an air classifier or secondary shredder. This would reduce the throughput of the primary shredder and allow certain recoverable materials, such as glass, to remain in larger piece sizes, important for recovery. In this way, operating costs for the shredder would be reduced and the recoverability of materials, and hence the revenue, increased.

Jan 1, 1975

By C. Perea, O. Restrepo, C. Ihle, H. Estay

In this study, research on the use of monosodium glutamate for copper leaching, with emphasis on the thermodynamics and oxidant characteristics, is presented. Copper dissolution was conducted following a hydrometallurgical route, using monosodium glutamate in alkaline solutions. The effect of oxidizing agents such as hydrogen peroxide (H2O2) and potassium permanganate (KMnO4), and the efficiency of copper leaching with glutamate compared with glycine have been studied. Results, obtained at room temperature, showed 92% recovery of copper using 0.03 M hydrogen peroxide, 0.5 M monosodium glutamate at a pH of 9.44.

Mar 2, 2022

By John W. Stevenson

At the No. 4 Mine of Jim Walter Resources in Tuscaloosa County in the North Central part of the State of Alabama, the Mary Lee and Blue Creek coal beds lay 2000 feet below the surface. The quantity of methane gas stored within the coal bed reservoir at this depth and released during development mining necessitates that each coal producing section be ventilated using large air quantities approaching 100,000 cfm. In order to meet coal contractural commitments in the early stages of mine development by installing the necessary number of continuous mining machine units and to develop the mine to projected air shaft sites, high pressure, large volume mine ventilating fans were required. This presentation discusses the installation start-up and changeover procedures when two size GAF 31.5-28-1 TLT-Babcock 3500 Horsepower fans with adjustable pitch in flight blades were put on line while phasing out two Jeffrey Mining Machine Company 8HUA 117 Fans. A graph will be presented to depict the most economic diameter shaft size under 2000 feet of cover with different air quantity requirements.

Jan 1, 1982

By James P. Connell

The American Concrete Institute defines "shotcrete" as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity unto a surface." This definition thus includes what is traditionally known as "gunite," which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this paper. In 1914, following the invention of the mortar gun in 1907, the then Chief Engineer of the U.S. Bureau of Mines, George Rice, developed the guntie process for underground test work at the bureau facility at Bruceton, Pennsylvania. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto Tunnel in California. The greatest development was In Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Intially, shotcrete was used to reduce manpower requirements for forming; and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately niter the opening had been made. The incorporation of wire mesh into the shotcrete led to the New Austrian Tunnel Method, or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the U.S. reliance on wood or steel supports in main line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to the new and seemingly unrealistic lighter shotcrete support.

Jan 1, 1977

By Neil D. Policow

Dewatering of the fine clean coal fraction, - 28 mesh (595 microns) represents one of the most difficult and costly separations in typical plant circuits. Since 1969, the Screen Bowl Centrifuge has offered an economical alternative to filtration/thermal dryer combinations. The performance of Screen Bowl Centrifuges has been continuously modified and improved to dewater not only coarser coals, but also today's variety of ultrafine material. Actual test comparisons with alternative methods show the Screen Bowl Centrifuge to be most cost effective and efficient when all factors are considered.

Jan 1, 1982

By G. R. Erdman

The industrial mineral filler plant of the Gouverneur Tale Company is equipped with a good dust collection system installed long before the recent popularization of environmental pollution. Credit for this fact is due to the foresight of Mr. R. S. McClellan, Project Manager and subsequent Vice President and General Manager of Gouverneur Talc, who recently retired as Vice President Engineering of the parent organization, the R. T. Vanderbilt Company. Also instrumental in the early stages of plant operation and the solution of start-up problems was J. A. Gustin who is now an engineering consultant located in Martinsville, Va. Credit is most certainly due to the late R. T. Vanderbilt, the company's founder, who favored and approved the investment in the necessary facilities that were far ahead of all competitors in the industry at that time.

Jan 1, 1972

By Jason Clarke, Glen Trainor

As the mining industry faces increased challenges with declining ore grades and harder to access deposits, operating mine sites in an environmentally responsible and economically viable manner will require innovations that improve efficiency in energy logistics, and automation. Technological advancements in mining have been successful primarily because of the willingness and capability of these solutions to share information with one another, for example OEM payload systems sending information to Fleet Management Systems, and in turn Fleet Management Systems interfacing to ERP systems. To promote and facilitate the sharing of data, there has been a push towards open standards with initiatives led by organizations like ISO, ISA, EMESRT, and GMG. These efforts are aimed at creating a more collaborative and interoperable environment within the sector. However, when it comes to implementing autonomous solutions, a different trend dominates— closed-stack solutions. These closed stack solutions not only prohibit a mine site from selecting best-of-breed solutions, by blocking the competition from entering the market, they also risk slowing innovation that could help overcome the challenges the mining industry faces. Open Autonomy, an internationally published standard that allows any FMS to work with any Autonomous solution, breaks this closed-stack approach and invites competition from other industries. This competition comprises of autonomous suppliers from other industries and manufacturers of smaller, civil-sized haul trucks. The availability and capabilities of these smaller-sized autonomous haul trucks will help tackle the challenges of responsibly and economically mining lower quality ore grades and mining harder to access deposits.

Feb 1, 2024

By R. Miller

Lowering our globe’s emissions is a major effort as we move toward a future net-zero carbon environment requiring significant investment in a new, low-carbon infrastructure, along with key market incentives to change. Industry will play a key part in this transformation, requiring expertise in both energy and emissions. Key elements of the de-carbonization strategy are: energy data, emissions reporting method, governance, de-carbonization project generation and drivers, the MACC, electrification, and the de-carbonization checklist. For a zero carbon future, it will be key for business leaders to understand decarbonization, anticipate technological changes, and implement new business me

Mar 2, 2022

By R. W. Sayers

The Duval Corporation porphyry copper deposits at Copper Canyon and Copper Basin, though widely separated, form an economic unit requiring integrated exploitation. Contrasts in mineralization, host rocks, and mode of occurrence present unique mining and milling problems. Mixed oxide-sulfide ore is treated in extensive dump leaching facilities in both areas. Complex copper-gold-silver ore is treated in a 4,000 tpd mill at Copper Canyon. In both areas, hypogene metallization occurs within large aureoles of metamorphism and hydrothermal alteration related to quartz monzonite intrusions of mid-Tertiary age. Supergene processes further altered the rocks and enriched the hypogene protore. At Copper Canyon, hypogene copper and iron sulfides with gold and silver occur in fractures, as partial replacement of favorable beds, and as disseminations in Paleozoic sedimentary rocks. The lower part of the Pennsylvanian Battle Formation was a particularly favorable host. Metallization occurs to a lesser extent in quartz monzonite. Metal zoning is well developed. The deposits at Copper Basin consist principally of supergene copper minerals in arenites of the Cambrian Harmony Formation. Oxidation of hypogene copper and iron sulfides in tactite zones has formed at least two commercial deposits; intersections of fractures with favorable beds exerted important ore controls.

Jan 1, 1968

By Gordon B. French

The Occidental Oil Shale mining and retorting system for the production of shale oil has many advantages over the conventional underground mine and surface retort systems. For example only a portion of the oil shale is mined and transported to the outside, where it blends with the existing shale talus found on most of the slopes in the immediate area. The retorted spent shale is retained underground so that it does not become a surface disposal problem. The process consumes only minor amounts of water which is produced in adequate amounts in the retorting to fulfill all mining operations needs without outside supplies. Noise and dust levels are kept to a minimum with most of the facilities located underground. The exception being the generating stations and facilities as required to monitor air and water qualities, and last but not least, more than four times as much oil is pro¬duced from a given acre than from conventional surface processing. With the increased thicknesses as available on the government monopoly area this number could be increased by a substantial amount.

Jan 1, 1975

By R. A. Seitz

This paper presents a framework for analyzing the theory and industrial practice of coal flotation and gives some examples of its use for understanding flotation phenomena and optimizing/controlling flotation circuit performance. It is based on extensive laboratory and in plant test work conducted over the past several years by researchers at MTU as well as an analysis of the literature. Previous researchers have usually considered either the surface chemistry or the kinetics of coal flotation behavior, only rarely have these factors been considered together. However, these factors must be considered together in order to gain a clear understanding of the theory underlying coal flotation such that its practical application can be optimized. Fortunately, this complex objective can be achieved by considering the recovery and rate of recovery of the different types of particles present in the feed to coal flotation circuits and the fundamental mechanisms responsible for these recovery phenomena. The influence of three major groups of variables must be considered: control variables (reagent additions, aeration rate, etc.); disturbance variables (feed pH, percent solids, etc.); and circuit design variables (number of cells, circuit arrangement, etc.). Each of these groups of variables affects process kinetics in a clearly understandable manner, which, once determined, is extremely useful in circuit design and optimization. This paper includes a discussion of the use of the proposed framework to explain the effects of some coal characteristics on flotation performance. In addition, an example of using this analysis to optimize the performance of a coal flotation circuit using frother and collector addition levels is included.

Jan 1, 1985

By Dennis S. Kostick

Soda ash is produced in over 39 countries by the Solvay ammonia-soda process or by mining natural sodium carbonate deposits. The total production of soda ash in 1980 is estimated at slightly over 29 million metric tons. Synthetic production accounted for over 75% of this amount with the balance of production originating from natural sources (either trona or sodium carbonate-rich brines) found primarily in the United States, Mexico, Kenya, and Chad.

Jan 1, 1981

By K. W. Grubaugh

The recently enacted federal surface mine law (P.L. 95-87) will increase further the complexity of securing a reclamation permit. This law intensifies the need to present the required reclamation plan in a thorough and comprehensive manner. One plan format, that used in construction performance contracts, offers promise of filling this need. Reasons for using the format of expressed, bilateral, negotiated contracts common to the contruction industry, and the salient aspects of an application which uses this format are reviewed. Advantages of this procedure are seen to be improved mine planning, awareness of the total design job, potential for improved speed of permit acceptance and improved cost control.

Jan 1, 1978

By Robert W. Bartlett

Both hydrometallurgical and vapometallurgical processes often involve ores that have been previously ground and size classified. When the valuable mineral is substantially liberated, the chemical reaction is likely to occur on the particle surface and the particle core will shrink as the reaction proceeds. If the chemical reaction products are solid materials then a solid shell, usually porous, will form around the shrinking core. This is known as the core/shell or topochemical reaction model. Using a spherical approximation for the particles, equations have been developed to express the extent of chemical conversion of the particle, depending on which one of the following process or mass transport steps is rate controlling:1 (1) chemical reaction at the particle surface, (2) diffusion through the thickening reaction product shell or (3) mass transport through a boundary layer surrounding the particle. In a previous paper2 these equations were coupled with the Gates -Gaudin-Schuhmann equation 3 4 describing the distribution of particle sizes resulting from comminution of rocks and other brittle solids to develop reaction yield curves expressing the weight fraction of metal or other valuable component of the feed that was chemically converted as a function of residence time. This was done for (a) batch, (b) continuous plug flow and (c) continuous back-mix flow (continuous stirred tank) reactors or process vessels. To make the curves of general rather than special utility, the residence time (average residence time for back-mix reactors) was normalized to a dimensionless time by dividing by the time required to completely chemically convert the largest particle in the feed to reac-

Jan 1, 1972

By David J. Hatem

Public-private partnerships (PPP) are gaining in popularity at the federal, state and local levels as the public sector seeks private capital to finance infrastructure and other projects that traditionally have been funded with public funds. In general, a PPP involves a development agreement between a public owner and a private sector concessionaire. Under the development agreement, the concessionaire is responsible for financing, designing, constructing and typically operating and maintaining the completed project for a concession period (often multi-decades in duration). The concessionaire typically enters into an agreement ? the design-build agreement ? with a design-builder to design and construct the project. The concessionaire may secure financing from banks, investors or from a combination of these and other sources (collectively the financier). While the PPP experience in the United States has been modest to date, an increasing number of projects involving tunneling or other significant subsurface work are already being delivered in the PPP mode. Public owners have significant options to address risk allocation for subsurface conditions on PPP projects. The same sound and fundamental principles of fairness in risk allocation that apply in other major subsurface projects should be applied and adopted in the PPP context

Mar 1, 2014

By P. G. Irwin

Natural resins, those derived from coal and those mined in the Uintah basin, face challenges from synthetic resins that are derived from petroleum sources and rosin or wood sources. In the past, fossil resins from coal were produced by various companies, the last one being Hercules, Inc., which sold BLACKHAWK resin until a fire destroyed the plant in the mid 1970's. Approximately four to fjve million pounds of BLACKHAWK were produced and sold mostly to the printing ink industry. Uintaite, more commonly known as Gilsonite® resin, was widely used by various industries, notably in printing inks, coatings, stains, adhesives, foundry, asphalt paving, and oil well drilling muds. Gilsonite has lost market share over the last thirty years to various synthetic resins particularly hydrocarbon resins that are derived from petroleum sources.

Jan 1, 1990

By M. T. Atwood

For more than sixty years the rich oil shale formations of Colorado, Utah and Wyoming have been evaluated as a future source of petroleum. After many false starts the commercial production of shale oil is near. Union Oil and Colony (Exxon and Tosco) have begun construction of commercial plants. Occidental and Rio Blanco (Gulf and Standard of Indiana) are well along in the development of modified in situ (underground) processes. A number of other companies and groups are in advanced stages of development. This paper will review some of the major elements involved in the production of shale oil with emphasis on means available to express the efficiency of production of pyrolysis liquids and gases from oil shale rock.

Jan 1, 1982

By F. X. Ferney

The centrifuge which will be reviewed in this dis¬cussion is the continuous solid bowl typo. As there are presently approximately 2000 of these units operating in our country, and about 200 of these in use in the coal industry, I expect that most of you are acquainted with its operating principle. How¬ever, for those who are not familiar with the machine a brief introduction is in order. The continuous solid bowl centrifuge was first successfully marketed, worldwide by the Bird machine Company in 1934. The successful development of this unit was based primarily on the invention of a drive mechanism to properly control the differential speed between the two rotating elements. This centrifuge was introduced into the coal industry immediately following the second World War. Today there are five or six additional firms' selling this machine in our country, and approximately twenty others in Europe, England and Japan.

Jan 1, 1965

By Donald R. Simon

Money... not many subjects are as personal or as emotional. Hessiod said it well in 700 B.C. "Money is life to us wretched mortals". Are you getting paid enough? Does your company reward its top people? Does coal or copper pay more? Production or engineering? How is the synfuels industry going to influence mining salaries? Do high salaries attract and retain the best people? Do modern compensation systems ensure fairness or destroy entrepreneurial spirit? With our tax system and high standard of living why are we so salary conscious? Salary is not only important for what it can purchase but it is also a yardstick, measuring how well we are doing. We all need money to pay the bills and maintain our standard-of-living, but once we reach a certain point the psychological ramifications become more important than the purely practical side. Even necessary payments like the mortgage and the car are a function of our egos. Are our choices of cars and homes based on simple transportation and shelter?

Jan 1, 1980

By Randall D. Peterson

Strip mining with draglines and other surface equipment has traditionally been the method of choice for mining shallow deposits. This is particularly true for soft deposits that require little or no blasting. High rates of productivity and low operating costs have set this standard. However, these methods can be improved. Strip mining methods are batch processes and difficult to accommodate in processing. Moreover, they are encumbered with overburden removal, reclamation expense, and human inefficiencies. This paper describes the invention of a novel shallow earth mining technique called the Softwall Mining Method. Softwall Mining is an adaptation of longwall mining for loose earth conditions. The method was specifically invented for recovering phosphatic clay ore from beds in North Central Florida, but is likely to be suitable for a number of other minerals as well. Potential deposits for which the method may be well suited include placers, disseminated deposits in soft host rocks, bauxite, soft coals and lignite deposits, and other deposits where overburden will subside readily and where the ore can be hydraulically broken and slurried. Unit operating cost advantages are expected over the current dragline systems used. The Softwall mining advantages are its high rates of productivity, control and automation of the mining process, reduction of dilution and waste, and elimination of the majority of stripping and reclamation.

Jan 1, 1998