Search Documents

By Susan T. Bagley, Kenneth L. Rubow, David H. Carlson, Bruce K. Cantrell, Winthrop F. Watts

Permissible exposure limits (PELs) have been established for gaseous pollutants, carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), nitrogen dioxide (NO2), and some gas-phase hydrocarbons emitted in diesel exhaust. There is, as yet, no PEL recommended for diesel exhaust aerosol (DEA), nor is there a standard method for sampling this aerosol. The University of Minnesota and the U.S. Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size-selective inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were made in underground coal mines that use diesel equipment. The mine mean DEA concentrations for the five mines surveyed, determined with the PDEAS in the haulageway, was 0.89 mg/m3 with a standard deviation of 0.44 mg/m3. DEA contributed 52 % of the respirable aerosol at this location. In three of the mines filter samples were collected for DEAassociated polynuclear aromatic hydrocarbons (PAHs) and biological activity determinations. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust. In general, the PAH and biological activity levels were similar for all three mines, and indicate that up to 25 % of the haulageway concentrations may be contributed by outby diesel vehicles. Measured concentrations of CO, C02, NO, NO2, and SO2, were well below regulated levels. INTRODUCTION Diesel exhaust contains pollutant gases, such as carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and gas-phase hydrocarbons, as well as DEA. Much of the health-related concern focuses on DEA and associated organic compounds (Watts, 1992a). A wide variety of these PAHs have been identified and some are known carcinogens and/or mutagens. The U.S. Mine Safety and Health Administration (MSHA) has proposed new PELs for these and other contaminants (MSHA, 1989). MSHA has also published an advance notice of proposed rulemaking to establish a separate PEL for diesel particulate (MSHA, 1992). The U.S. Bureau of Mines has collaborated with the University of Minnesota to develop and field test a PDEAS. The PDEAS is a three stage sampler based on the MSA' personal respirable dust sampler. It utilizes a respirable cyclone preclassifier followed by a 0.8 µm cut point impactor and afterfilter operating at a flow rate of 2 L/min. Respirable aerosol greater than 0.8, µm in size is collected by the impactor while DEA, less than 0.8 µm in size, is collected by the afterfilter. Hence, gravimetric analysis of the afterfilter permits measurement of DEA concentrations. This development and laboratory evaluation of the PDEAS were described previously by Cantrell (1990) and Rubow (1990). During field tests of the sampler, numerous air quality measurements were made in continuous miner sections of five underground coal mines that use diesel haulage equipment. These air quality measurements included levels of selected PAH and biological activity associated with DEA collected in the intake and haulageway areas of three of the five underground mines, and CO, CO2, NO, and NO2 in two of the mines. The objectives of this paper are to present the DEA and associated pollutant concentrations measured in these mines and to assess the impact of diesel face-haulage equipment on underground mine air quality. MINE DESCRIPTIONS The mines used for the PDEAS evaluation were designated J, K, L, N, and 0. Mines K, N, and 0 are located in the Western United States, while mines J and L are located in the East. Each mine produces high volatile, bituminous coal with shift production levels varying from 500 to 2000 tons/section. Seam heights varied from 1.5 to 3.0 m. Mines K and N use continuous mining to develop longwall panels. The others are strictly room-and-pillar operations using continuous miners. The number and types of diesel-powered vehicles used at these mines were described by Watts (1992b). Mines J, K, N, and 0 use diesel power to assist in a wide range of activities in addition to coal haulage. These included road maintenance, personnel and materials transport, lubrication, and welding. Mine L used only three diesel-powered shuttle cars to haul coal. SAMPLING AND ANALYSIS METHODS Aerosol Measurements Aerosol samples were collected in the mine portal area, the clean air intake to the continuous miner section, the haulageway one crosscut inby from the feeder breaker and belt, in the return airway, and on selected personnel. The haulageway sampling site was located near the point where the diesel-powered shuttle cars turn around to dump their loads. Additional respirable and DEA samples were collected and have been reported by Haney (1990).

Jan 1, 1993

By D. H. Garcia

The mining industry responded to public concerns about use of cyanide by developing a voluntary certification to allow companies to demonstrate their commitment. The International Cyanide Code (Code) establishes standards for the manufacture, transportation and use of cyanide. Key concepts in closure planning to comply with the Code are to decommission all facilities related to cyanide operations and to provide a financial assurance mechanism for those activities. Code requirements may differ from state-specific regulations, but requirements are based on closure goals for protection of the human health and the environment. Only issues related to cyanide operations are required to be included in decommissioning demonstrations. For example, the disposal method of cyanide solution holding tanks and the cost must be included in the closure plan, but information regarding closure of roads is not required. Closure costs must be based on a third-party contractor as opposed to internal budgets. Compliance with the closure requirements of the Code allows companies to show their stockholders, lending institutions, and the public that their operations are environmentally responsible.

Jan 1, 2010

By Reynold Q. Shotts

Underground mines, penetrating well below the water table, quickly fill with water when abandoned. Ordinarily, these natural cisterns are not thought of as sources of industrial water. Under special circumstance, if chemically treatable, they might become valuable industrial water reservoirs. An example of a group of about 20 mines in a geological and structural setting insuring water entrapment, rapid recharge and a possible minimum of contamination, are the small, compact Belle Ellen and Piper basins in Alabama's small but second most productive coalfield, the Cahaba. The mines have been abandoned from more than 50 to less than three years. The county now produces about a million tons of coal annually, all from strip mining. Figure 1 shows an idealized cross section of the strata in the Belle Ellen syncline near West Blocton, Bibb County, Alabama. Figure 2, 3 and 4 are maps showing the location of the syncline, other structural features, the outcrop lines of the three principal coalbeds underlying the basin, and the mined-out areas on the three beds (1).

Jan 1, 1973

By Paul Soros

Lord Robens, Chairman of the National Coal Board of England announced recently to the world press plans for construction of the largest bulk terminal in Western Europe. This should result in annual freight savings of 22.4 million dollars and between 150 and 190 million dollars of new export business. These are rather substantial amounts for any mining enterprise. Or to put it another way, opportunities to make substantial savings in the delivered price of a highly competitive commodity such as coal are few and far between. One area where such opportunities still exist is in the economical; movement of bulk materials between producer and consumer.

Jan 1, 1966

By S. Tuylu, D. Adiguzel, A. Bascetin, O. Ozdemir, U. Cinar

"In recent years, use of mineral processing tailings as a paste backfill has been significantly increased due to the environmental problems occurred during the disposal of the tailings in mine area. The paste material used to fill the stopes excavated is generally consisted of tailings (solid ratio: 70–85%) and cement (3-7%w/w). Meanwhile, the strength of the paste material is completely related to ratios of these materials. Cemented Paste Backfill (CPB) system is used as support depending on the roof pressure and also as an underground disposal method. Therefore, temporary strength value of the paste material gains a great importance. For example, the paste backfill material must compensate the minimum 4 MPa strength value in order to procure the permanent fortification, and the mixture cost must be minimal as well. For this reason, in this study, the Pb-Zn tailings were used to prepare for the paste backfill material using cement in order to perform the uniaxial compressive strength (UCS) tests. Additionally, a statistical experimental design and linear programming techniques was used to find the optimum mixture in terms of strength and cost. The pulp solid ratios (PSR) of the tailings and cement (by the solid) were varied as 75-85% and 3-8%, respectively. The results of this study; the optimum mixture is ~79.5%PSR and 6.8% cement ratio (by the solid) for 4 MPa UCS (28 day) and 16-17 cm slump value determined by this method with statistically reviewed experimental data. INTRODUCTION Fine-grained tailing waste materials resulting from mining activities are an important environmental problem. In terms of environmental protection, the use of tailings with paste backfill is a very attractive approach and a desirable solution to tailings management. Paste backfill, which is used to fill underground openings, is made by primarly mine tailings mixed with hydraulic binders and water. Its main benefits are not only disposal of mine tailings in underground, but also providing a certain strength to ensure a safe working environment. Therefore, it is necessary to use hydraulic binders due to durability of the system (Benzaazoua et al., 2004). Paste backfill, formed from the mix of dewatered plant tailings (75-85 wt. % solids), water and binder (3-8 wt. %) (Brackebusch, 1994; Landriault et al., 2005).Water is used to determine the chemical reactions between tailing and binder materials for strength as well as increasing pumpability. Portland cement and ash can be used as binder materials (Douglas and Malhotra, 1987). The factors which affect strength and stability of paste backfill separate into two groups called interior and exterior factors. Interior and exterior factors determine the strength, stability and deformation features of backfill in short and long terms and also affect the transportation of backfill to underground (Benzaazoua et al., 2004; Erçikdi et al., 2006; Yilmaz et al., 2010; Nasir and Fall, 2010). Material properties of tailings as well as site operations to fill the underground openings are the most important steps for the design purposes. Grain size distribution, chemical, and physical properties of tailings, and mechanical properties of paste fill material are used to understand the suitability of tailings as paste fill material (Ozturk et al., 2014). In addition, Fig. 1. is also proposed to apply a typical design for the operational stages of paste fill applications on the site."

Jan 1, 2016

By D. Lauriski

The recent spate of catastrophic events at U.S. mines raises the question as to whether or not the mine safety and health system in the U.S. is broken. The prescriptive regulatory regime in the U.S. is not a cure-all for a broken system. Without totally dismissing the contribution of a prescriptive regulatory approach, this paper argues that safety in the U.S. mining industry would be enhanced if the nation adopted a scheme that provides a balance between specification standards and two alternatives: performance and systems-based standards. This would allow effective and flexible means to continuous health and safety performance improvement. Mine operators, regulators and politicians could then go beyond thinking that compliance alone equals strong safety by creating a proactive system that emphasizes continuous improvement. By adopting performance and systems-based standards, exemplary safety and health performers can be recognized, allowing regulators to focus their efforts on those without sound occupational safety systems and who have substandard safety performance. Mining Engineering, 2011, Vol. 63, No. 7, pp. 77-82. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Sepp A. Kutschera

are gaining increased interest for over­burden removal and ore production at large open cast mines. The application of bucket wheel excavators is still tied to soft un­consolidated rocks and soils, while belt conveyors can cope with all kind of matri­als restricted only by the top grain _ size. Therefore, mode of transport and the re­quirement of down stream ore processing de­fine the materials size distribution. These requirements are usually met by primary crushing or scalping. The paper discusses general applica­ tion criteria of bucket wheel excavator with systems primary for in-pit overburden crusher removal. and It _indeapits scalper units and discusses their technical and operational features. It further com­pares the capital and operating cost struc­ture relative to the syste

Jan 1, 1992

By Matthew T. Mowry

As the mining industry continues to hire young professionals to supplant the growing number of retirees, a well-developed engineering curriculum, coupled with practical, real-world training, can prepare mining engineering graduates to make meaningful contributions in the industry. Successful companies can be measured not only by their reserve base and annual production but also by their retention of mining engineering graduates with zero to five years of operational experience. My personal experience in the industry during the last five years has been varied and rewarding. The knowledge and experience I have gained have taught me valuable lessons that prepared me for my current role.

Nov 1, 2013

By T. P. Weldum, W. Conger

"The objective of the study conducted by the authors is to determine what media size(s) addition will maximize any given plant ball mill’s grinding efficiency (Fig. 1). The functional performance parameters “mill grinding rate through the size of interest,” and “cumulative mill grinding rates” from both plant and smallscale tests are applied to this task. A plant media sizing methodology, and industrial case studies, are provided.BackgroundA previous article (“Ball mill classification system optimization through functional performance modeling,” Nov. 17, McIvor et al., 2017, Mining Engineering) described circuit classification system efficiency (CSE), equal to the percentage of coarse (plus circuit P80 target size) material in the ball mill. It can be measured and then increased through pump and cyclone adjustments. By so transferring the application of ball mill power from fine (minus P80 product size) to coarse material, circuit efficiency is increased and overgrinding is decreased.The other factor that determines overall circuit efficiency is how well the power that is applied to the coarse material grinds it. This is affected by design and operating variables like the media sizing and mill percent solids. From circuit functional performance (McIvor et al., 1990):Circuit production rate of new fine material (t/h) = Power applied to coarse material (kW) x Mill grinding rate of coarse material (t/kWh) (1)The power applied to coarse material is the total mill power multiplied by the CSE. Therefore:Circuit production rate of new fine material (t/h) = Total mill power (kW) x CSE (%) x Mill grinding rate of coarse material (t/kWh) (2) Production rate, mill power and CSE can be measured during a plant circuit survey. The mill grinding rate of coarse material is then calculated. At the circuit target P80 size, this is the mill grinding rate (of coarse material) through the size of interest. The objective is to maximize this rate. The mill grinding efficiency can also be calculated by taking the ratio of the mill grinding rate over the material’s grindability as measured in the lab. Mill percent solids optimization has thusly been achieved (McIvor et al., 2000). For media sizing, maximizing the mill grinding rate on a given ore is equivalent to maximizing the mill grinding efficiency. Ores of different grindability will be part of the discussion."

Jan 11, 2018

By O. J. R. Baena

Mining activity in the Segovia region in NE Colombia is the main source of employment in the local economy. This has created major problems of illegality and informality mining associated with a high social and environmental impact, as inefficient technologies are used and high consumption of toxic substances required in the process of gold recovery by amalgamation and cyanidation. In this work is presented mineralogical characterization of six local mills and studied beneficiation processes developed in them. With the results presented a proposed plant design that eliminates the use of mercury by replacing gravity concentration processes taking advantage of the characteristics of the treated material. Significant results were obtained regarding the recovery of precious metals and present a methodology that can be replicated in other mineral beneficiation plants that use gold amalgamation processes. This implies a significant reduction in mercury use and decreased risk of human contamination associated with this.

Feb 23, 2014

By Yues Bertube

Molybdenite and chalcopyrite are two often-associated minerals. In Quebec, the Gaspe Copper Company, a subsidiary of the Noranda group, currently operates a molybdenite flotation circuit to recover a one percent trace of this mineral in the chalcopyrite concentrate. The low levels of molybdeni 2 preclude the use of flotation to remove molybdenum directly from the ore while scavenging of chalcopyrite concentrate for molybdenite yields a concentrate of the latter of somewhat inadequate quality. Such a situation could possibly best be solved by hydrometallurgical means, if molybdenite could be leached selectively from the chalcopyrite concentrate. Work in the field of extractive metallurgy was initiated about 22 years ago in the laboratory of the department of mining and metallurgy at Laval University, Quebec. Following a literature search, two objectives were selected. The present talk will outline some of the results obtained to-date and it is hoped the ensuing discussion of the paper can raise questions of immediate assistance to us for the future. First, as an immediate objective of-practical use, the oxidation rates for molybdenite and chalcopyrite in alkaline media would be studied under conditions of possible industrial application. Secondly, the kinetics of mass transfer of gases in pressure reactor are to be studied. Solubility data for various gases in aqueous solutions have been gathered by a few investigators, to mention the work of Pray1, Wadsworth2, Pawlek3 and Gerlach. Scattering in experimental results and discrepancies between authors are ominously present. Kinetics of mass transfer have somewhat been more neglected. A systematic investigation by the school of Berlin has greatly helped in the design of impeller most suitable for gas dispersion, without much reference however to the solid dispersing ability of the various designs. Variables affecting rates of gas transfer to the solution have not been studied. Studies on the aqueous oxidation of sulfide minerals are much more numerous. While molybdenite has been relatively less studied, work has been carried in two areas namely in alkaline oxidation of MoS2 , work performed by Dresher2 and Wadsworth, and in the hypochlorite leach of molybdenite by Bhappu4 and co-workers, These two methods showed appreciable rates of leaching for molybdenite. In general, comparisons between rates of oxidation of this sulfide with that for chalcopyrite have not been made.

Jan 1, 1972

By Boris CARO VARGAS, Bernard Theron

"In early 2014, Nicholson Construction Company was awarded, together with its tunneling sister company Bessac, the Norris Cut Miami Tunnel Project. The 2.5-meters diameter segmental lined tunnel, 1600-meters long, is aimed to replace the existing 54” force main connecting the Waste Water Treatment Plant (WTP) on Virginia Key to Fisher Island. To overcome project challenges such as the highly permeable limestone of the Fort Thomson Karstic Formation (one of the most permeable formation in the World), the project team has developed State of the Art solutions: The TBM was launched with pipe-jacking technique for the first 70-meters and then converted to segment erection mode. It allows substantial schedule savings and drastically reduces the size of the circular launching shaft. The TBM, jointly designed and manufactured by Bessac and Herrenknecht, can convert from slurry to EPB mode within a few minutes. The cutters can be replaced by wet divers thanks to an innovative application in the TBM industry. PRESENTATION OF THE PROJECT The aim of this project is to replace the existing 54-inch force main pipeline which transmitted all sewage collected from Miami Beach, Surfside, Bal Harbour, Bay Harbor, North Bay Village and Fisher Island to the Central District Wastewater Treatment Plant (CDWWTP) to Fisher Island. The existing pipeline consisted of pre-stressed concrete cylinder pipe which is in poor condition in a number of locations and could be subject to sudden failure. An adjacent portion of this existing force main under the Government Cut (North Fisher Island) has already been replaced as part of a previous design-build contract and involved the installation of a 60-inch diameter fiberglass-reinforced mortar pipe installed inside a micro-tunneled casing."

Jan 1, 2016

By C. Opoku-Ware, M. Kukay, P. Conrad, F. Inkoom, R. Pal

Researchers at Montana Tech are investigating the potential for developing trees tolerable to degraded un-reclaimed mine site tailings and soils as a solution to re-establishing long-term tree growth on those sites. This project involves growing tree seedlings from seeds planted in the degraded mine tailings and soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in degraded tailings and soils in Butte, Montana with minimal post-planting human intervention. Work conducted on the project to date has shown successful growth of seedlings in degraded tailings and soils. INTRODUCTION In an effort to improve Butte Area One natural resources, this research project is working to help restore tree growth in the Butte Priority Soils Operable Unit Boundary (BPSOU) (Opoku-Ware, et al 2018). Research by Blicker, et al (2003) found that, the BPSOU, which is part of the Silver Bow Creek/Butte Area National Priorities List (Superfund) Site within and near Butte, Montana has multiple historic mining sites situated entirely within the urban setting of Butte. Mine wastes and mill tailings, accumulated from over 100 years of gold, silver, and especially copper mining are dispersed throughout Butte, posing health risks to human and environmental receptors. Stabilization of tailings sites is needed to control fugitive dust, prevent run-off of toxic material resulting in subsequent sediment deposition in streams, reducing the volume of water seepage through acidic and heavy metal contaminated material, and improving land productivity and aesthetic values (Watkin and Watkin, 1982). If successful, the project will help restore water quality and maintain stream flow in Silver Bow Creek where it flows through Butte Area One. Trees native to Butte are being grown to seedlings in a greenhouse located on Montana Tech’s campus which will be planted in degraded soils located within the BPSOU. Growing trees is expected to help restore vegetative ground cover within the watershed contributing to stream flow in Silver Bow Creek. The trees will prevent soil and tailings from eroding and being deposited in Silver Bow Creek where they could degrade water quality and choke stream flow. The project combines research with tree seedling growth to provide a resource for Butte that could produce thousands of tree seedlings each year adapted to the harsh climate, soil, and tailings conditions that exist in the BPSOU where they will grow. It is anticipated that the trees developed by the project will have the capability for long-term survival and growth because they will be germinated and grown into seedlings in the degraded soils and tailings collected from the BPSOU where they will be planted. Soils and tailings collected for the project have been evaluated to determine if they lack nutrients or contain substances potentially toxic to the long-term growth and survival of the trees. Toxic levels of metals, high concentrations of soluble salts, extremes in pH, nutrient deficiencies and imbalances, surface crusting, high bulk density, low infiltration rates, high surface temperatures, low cation exchange capacity, restricted microbial activity, low water retention, harsh climatic conditions and surface particle movement are some of the traits of mine tailings sites that restrict revegetation efforts (Barth, 1986).

Jan 1, 2019

By R. E. Turner

Hamersley Iron Pty. Limited, one of the world's largest iron ore producers, operates a 3.0 million tonne per year pelletizing facility at Dampier in Western Australia. The plant produces pellets for the export market using a blend of natural hematite fines from the Company's two mines at Tom Price and Paraburdoo. Processing includes fluidised-bed drying of the ore feed, open circuit dry grinding, disc balling and pellet induration in a travelling grate furnace of Dravo-Lurgi design.

Jan 1, 1980

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dust escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dusthog- type bit to improve dust extraction during the critical initial phase of drilling. A twistedbody drill bit is also evaluated to determine the quantity of dust liberated in comparison with the dust-hog-type bit. Based on the results of our laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emission can also be substantially reduced. The use of a twistedbody bit has minimal improvement on dust capture compared with the commonly used dust-hog-type bit.

Jan 1, 2014

By G. Reed Marchant

During the past two decades, we have witnessed the computer revolution. Like other revolutions, it has been successful in many ways; however, it has not been without difficulties. One of the areas where these difficulties have been more prevalent has been in the application of computers for the purpose of controlling industrial processes. During the early 1960's, many people naively assumed that bridging the gap between data processing and process control was a simple matter of connecting a few wires, doing a little programming, laying off most of the people and watching the plant make great increases in production as the lights on the computer blinked on and off. Unfortunately, it has not been that simple. Instead, a whole new-set of disciplines has been required to overcome the major obstacles that exist. Nevertheless, current successes are proving that the digital process control computer is here to stay, and that through the application of digital computers an attractive return on investment can be obtained in many applications.. The purpose of this paper is to illustrate some of the requirements for successful implementation of computer control systems, with particular attention to the following four objectives: First: Acquaint the reader with the general control problems so that he may more fully recognize the major requirements for successful implementation. Second: To acquaint the reader with the types of control hardware that can be considered for use in the development of control systems. Third: To discuss some of the major obstacles that must be overcome for successful implementation of computer control systems. Fourth: To discuss the systems approach in the development of control systems and to illustrate it in the implementation of an actual control system.

Jan 1, 1971

By Jerry G. Rose

This paper addresses a process by which both the disposal and utilization of preparation plant coal refuse can be simultaneously accomplished with an attendant benefit of significantly increasing the percentage of extractable coal. A laboratory study is described in which coal refuse was successfully utilized as an aggregate in low cost concrete (coal-crete) mixes under simulated mine environments. Coal-crete specimens with compressive strengths of 14,000 kPa (2,000 psi) were consistently produced. A construction sequence and mining plans are offered for placing the low-cost coal-crete pillars in accessible areas in room-and-pillar mines so that a Substantial portion of the remaining coal pillars could be extracted. The method could be applicable in areas where mining procedures do not permit pillar extraction because of possible surface subsidence, roof problems, or other conditions. Possible structural difficulties with the coal-crete pillar support system are discussed. Using a discounted cash flow analysis, the economic feasibility of mining with the coal-crete pillar system is investigated. The cost of the coal-crete pillar system is compared to the cost of a mining system which would have less coal recovery. The analysis indicates that although at higher coal selling prices the coal-crete mining system may yield an acceptable rate of return, the alternative of leaving the coal pillars is more attractive at the present time.

Jan 1, 1977

By Annan Cook

J.R. Atkinson, office engineer to Kennecott Copper Corp., summarized data on the Mineral Park area [Wallapai (Chloride) Mining District, Mohave County, Arizona, Fig. 1] and submitted it to the New York office in 1950. He recommended an examination. Weston Bourret, a Kennecott geologist, accompanied by B.S. Butler, the well known former US Geological Survey geologist, examined the larger of two hydrothermally altered areas in Mineral Park that same year. Bourret recommended that the property be optioned and mapped. Georges Ordonez, Kennecott's chief geologist, after a field examination, agreed with Bourret's conclusions At the end of the summer of 1951, Annan Cook (another Kennecott geologist) accompanied Ordonez to the property prior to starting a mapping program. At Ithaca Peak, the structure, alteration, and reddish-brown coloring in leached cavities-hematite, jarosite, and goethite with minor copper staining - made an interesting target. The Peak, which has since been mined, was a Laramide quartz monzonite porphyry grading into quartz porphyry, penetrating Precambrian rocks. Turquoise had been mined from several workings on the Peak. Surrounding the central area of alteration, but mainly to the northwest, there were many long-abandoned underground workings mined for zinc, lead, gold, silver, and copper. To the west of Ithaca Peak within the main area of alteration, surface evidence of a chum drill hole suggested interest in the disseminated mineralization probably prior to World War II. A topographic and geologic survey of the altered Ithaca Peak area was initiated by Cook in September 1951. He was assisted by Richard Vosburgh, field engineer, and by four geologists: Charles Goddard, III, Donlon LoBionda, Keith Martin, and A.T. Stone. When Cook returned to New York, Vosburgh was left in charge. Mapping continued and diamond drilling took place during the winter of 1951-1952. Drill sites were selected entirely on the basis of surface geology. Five drill holes, including a flat hole, located around the flanks of Ithaca Peak, averaged about 183 m (600 ft) in length. A sixth hole caved at less than 60 m (200 ft). The best values obtained were in the first hole (-45°): 90 m (300 ft) averaged 0.62% copper and 103 m (337 ft) averaged 0.041% molybdenum. In another hole, 43 m (142 ft) averaged 1.09% copper and 0:023% molybdenum. The values of copper and molybdenum in these two holes were generally higher than in the remaining holes, although molybdenum values were always around 0.024% or better. The New York office decided, however, to abandon the project even though the remaining field crew of three had recommended more drilling.

Jan 1, 1991

By J. W. Motter

Currently, virtually all new electric power generation systems under construction are designed with natural gas as the primary fuel. Factors driving these construction decisions involve sustained low prices for natural gas, environ-mental (and consequent regulatory) risks associated with the use of coal for power generation, and relatively high costs of construction for conventional coal-fired power plants. Despite the unarguable abundance of coal in the US. and worldwide, a fundamental question arises: What will be the role of coal in electric power generation in the 21st century? Congress, recognizing the vital and strategic importance of preserving the coal option for electric power generation, authorized the Clean Coal Technology Program. This pro-gram, with original funding in excess of $2,500 million, is intended to promote the demonstration and commercialization of a new generation of clean, efficient coal-based energy technologies through collaboration and partnering with private industry. The two technologies being demonstrated under this program which are the key to the continued use of this nation's huge coal reserves are coal gasification and the pressurized fluid bed. Either or both of these technologies, coupled with a combined cycle will pro-vide the continuing future coal option, while responding to increasingly more restrictive environmental standards. Recent Congressional budget-cutting efforts, however, could threaten the effectiveness of that model program, and ultimately other subsequent government-industry collaboration.

Jan 1, 1996

A kinetic model for leaching of various metals with different lixiviants in a batch system has been developed. Material balances for reactants and products at the solid/liquid interface were formulated and solutions to these balances were obtained in view of practical conditions. Special emphasis has been given to examine mixed controlled reaction systems where both heterogenous reaction and mass transfer play important role on the overall rate expression. The resulting kinetic expressions for either powder or rotating disc are discussed in light of experimental findings for various metals. Examples of the metal dissolution systems considered in this study include cobalt, nickel, copper and gold in acid, cyanide or ammoniacal solutions.

Jan 1, 1992