Search Documents

By J. Wiebmer

The two most important influencers of cost-per-ton in an underground mining machine are its productivity (tons/hour) and its availability-utilization (hours/year). Operating cost and initial price have far less impact. This paper reviews a cost-per-ton sensitivity analysis for underground mining equipment and discusses benchmarks for measuring its performance. The conclusion is that miner-supplier partnerships and the Information Age are the two most significant trends in cost-per-ton reduction.

Jan 1, 1997

By A. K. Fallaw, G. Wang, L. R. Moore, S. Dobson, Y. Xiong, J. Gu

"As ores degrade, mining techniques and chemistries change to meet market demand and maintain product quality. The balance of recovery and grade is a significant challenge in the Crago Process where an anionic collector is used to float phosphate, followed by acid scrubbing, then an amine float to improve product grade. As the grade is a requirement for DAP and MAP production, recovery is the criteria to suffer. Phosphate losses in the amine float can bring overall recovery down by as much as 18%, creating a growing need to think outside the box to improve recovery. This paper will focus on the theory of amine tail recycling and the best methods to optimize the overall phosphate recovery by recycling the tails from the cleaner flotation step. INTRODUCTION In 2014 the total US phosphate production was down 13% over the prior year, from 31.9 to 27.1 Mt, which accounts for 12.32% of the world’s phosphate rock production. Florida and North Carolina phosphate production accounted for 80% of total US phosphate production, which was down from 85% the previous year. This decline is due in part to the closing of the last phosphate mine in Polk County, FL - which had an operating phosphate mine for over 100 years (Gurr, 2015). Another factor contributing to the reduction in contribution from FL & NC is the increasing challenges in beneficiating the remaining ore deposits. The Central Florida mining district has historically been in the Bone Valley deposit, where raw apatite was abundant with P2O5 values as high as 15%. The Bone Valley ore also had characteristics favorable to beneficiation to 27.5-29.7 %P2O5 while achieving recoveries above 86%. The move southward into the Hawthorne Formation has seen the ore feed grade hit some historic lows, and the matrix characteristics pose more challenges to phosphate producers. The Hawthorne Formation experienced lateritic weathering after the Bone Valley formation which altered the apatite to aluminum phosphate minerals, and alteration of montmorillonite to kaolinite, releasing MgO that caused the dolomitization of the top of the Hawthorne limestone (Cathcart, 1966). Elevated levels of dolomite can yield an increase in slurry viscosities, reduce production rates, and increase energy costs in the wet-acid fertilizer process. The MgO will also act to dilute grade, making it more difficult to achieve a standard 18-46-0 product (McHardy, 1981)."

Jan 1, 2016

By M. Jack Snyder

The problem of effective utilization of fly ash has been given wide attention for a number of years. Although the effort devoted to the problem has led to some applications of demonstrated usefulness, the full utilization of fly ash has been held back by lack of concerted research and development activity, by lack of effective dissemination to potential users of fly ash of the knowledge that is available from laboratory and field studies, and by the obvious variability of the product. Because of the variability in fly ash from one power plant to another and from time-to-time in the same plant, specifications have been set up defining compositional or property limits within which a fly ash must fall to be used in certain applications. This paper discusses the bases for such specifications and examines them in the light of recent research on the characterization of fly ash. Other limitations and restrictions on the use of fly ash and what is being done to overcome them are also discussed.

Jan 1, 1968

By F. Ansheng

Though it becomes increasingly important with the valuable minerals in their deposits tending to be fine and poor, the solid and liquid separation remains difficult especially when the particles are of micrometer size and of low density. Almost of all conventional thickeners result in that fine particles lose into overflows which often costitutes a loss of potentially valuable resources as well as an environmental hazard. The addition of flocculations may improve the settling of solids but may also not work well for the final removal of fine particles from the overflows (Ref.1).

Jan 1, 1990

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy's program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997

By Sara J. Heinlein, George Malkos, James E. Lindell, Tony Pestonatto

The 79th Street Water Tunnel Extension Project was initially designed by the City of Chicago, Department of Public Works, to increase the capacity of the City’s south side water distribution system. MWH preformed a design review, prepared the final design and provided construction management for the City of Chicago Department of Water. Construction commenced in September 1995 and was completed in October 1999. The Project connected two existing water tunnels with a new 5.8 km (19,044 ft.) long, 4.9 m (16.08 ft.) finished diameter concrete lined rock tunnel utilizing TBM, drill-blast and mechanical hoe-ramming methods. In addition, approximately 61 meters(200 feet) of concrete lined variable cross section tunnel, a new gate shaft and a temporary construction shaft were constructed. This paper describes the construction of these features and the geological conditions encountered.

Jan 1, 2003

By M. A. Mahtab

This paper presents the results of a parametric study of the influence of natural features (stress field, rock strength, and strength and orientation of fractures) as well as the influence of induced features (undercut span, boundary slot, and other boundary-weakening measures) on the cavability of an undercut block of ore in mining by the block-caving method. The two-dimensional finite element analysis technique was used for this study. A coarse "mesh," along with linear homogeneous assumptions for rock properties, was used to model the problem of initiation of caving in a block of ore. Interpretation of the test results suggests that weakening the "abutments" of the block as well as certain orientations of natural fractures exercise significant influence on cavability. These findings hold promise for immediate application to known situations in block-caving mines.

Jan 1, 1975

By J. H. Hammarstrom, S. M. Fortier, W. C. Day, S. J. Ryker, R. R. Seal

"The United States’ supply of critical minerals has been a concern and a source of potential strategic vulnerabilities for U.S. economic and national security interests for decades (for example, see Strategic and Critical Minerals Stockpiling Act, 1939). More recently, with the rapid increase in the types of materials being used in advanced technologies (Fortier et al. 2018a), and geopolitical events surrounding the supply of rare earth elements (Ting and Seaman, 2013), among other developments, the critical minerals issue has again achieved a high level of visibility within the U.S. government (Executive Order 13817 (2017)).In this paper, the U.S. Geological Survey (USGS) provides an overview of its ongoing focus on critical minerals through the agency’s core competencies in mineral information, mineral resource assessments, geologic and topographic mapping, geophysical surveys and mineral resource research. Aspects of the multifaceted critical minerals issue addressed here include:• Identifying minerals that meet the definition of “critical” provided in Executive Order 13817.• U.S. net import reliance for critical mineral raw materials.• Current status of domestic critical mineral resource assessments.• Current status of topographic and geologic mapping, and geophysical survey coverage of the United States.• The Earth Mapping Resources Initiative (Earth MRI) to support future critical mineral exploration.• Critical mineral potential of waste streams from extractive industries.Identifying minerals as criticalU.S. government agencies and other organizations use a number of existing definitions and criteria to identify a mineral or mineral material as critical, strategic or otherwise important. The executive order defined a “critical mineral” to be “(i) a nonfuel mineral or mineral material essential to the economic and national security of the United States, (ii) the supply chain of which is vulnerable to disruption, and (iii) that serves an essential function in the manufacturing of a product, the absence of which would have significant consequences for our economy and national security.” This definition is broadly consistent with that defined by the National Research Council (NRC, 2008) and may be summarized as “essential in use” and “subject to disruption of supply.” Virtually all of the dozens of critical minerals studies conducted since the 2008 NRC report have used some variation of this same definition (Hayes and McCullough, 2018)."

May 1, 2019

By B. K. Parekh

Large reserves of coal pond fines are found in the Illinois Basin-over 40 million tons in Western Kentucky, over 65 million tons in Southern Illinois, and over 35 million tons in Southern Indiana. If these fines are used to produce coal-water slurry (CWS), fuel costs, NOx. emissions, and pond closure costs can be reduced. Coal fines from this region that are used to produce CWS for co-fire or re-burn may require processing, however, to attain proper particle size distribution and fuel quality. To evaluate the effectiveness of using coal cleaning technologies to control these CWS quality parameters, a simple flowsheet for recovering and processing coal pond fines was designed and tested. Coal fines processing consisted of using classifying cyclones to size at nominal minus 200 mesh, cleaning the classifying cyclone underflow using spirals, and cleaning the overflow using column froth flotation. Ash content of the dean coal from the spiral was reduced to about 10 percent, which is satisfactory to use for CWS co-firing in a cyclone-fired boiler. The clean coal from column flotation may be used for re-burn in a cyclone-fired boiler or as co-fire fuel in a wall-fired or tangentially-fired boiler. Heating value recovery during laboratory-scale, pilot-scale, and commercial-scale coal cleaning testing was about 80 percent.

Jan 1, 1998

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

By M. D. Scott

Lornex Mining Corporation operates an open pit porphyry copper mine in the Highland Valley southwest of Kamloops with a rated capacity of 43 500 TPD (48,000 TPD). It went into production in April 1972. Its concentrator consists of two grinding and flotation circuits in parallel each composed of a 6 000 KW (8,000 HP) 9,75 m (32 foot) diameter by 4,724 m (15'-6") semi-autogenous primary mill feeding two 3 000 KW (4,000 HP) 5,029 m (16.5 foot) diameter by 7,01 m (23 foot) secondary ball mills each feeding a bank of flotation cells. ,The original tailings system picked up the tailings from the flota¬tion circuits in a concrete collection box in the mill and carried the 36% solids density by weight slurry 488 m (1,600LF) through a 1100 mm (42 inch) diameter wood stave pipeline on a .46 percent slope to three 99,06 m (325 foot) diameter center drive thickeners. From the collection box under the thickeners the tailings line con¬sisted of three sections, carrying 50% solids density slurry. The first section consisted of 1460 m (4,800 LF) of 910 mm (36 inch) asbestos cement pipe for gravity flow from the thickener under flow elevation of 1252,4 m (4,109 feet) to the first pump station at elevation 1207,6 m (3,962 feet). Eight concrete drop boxes were used to limit the maximum slope on the pipeline to 0.5 percent.

Jan 1, 1976

By James E. Palmer

Geologic constraints on mining and recoverability include the following: coal seams too thin or thick for conventional mining methods; coal seams with insufficient stratigraphic separation; unstable roof or floor strata; discontinuous or lenticular seams; coal seams that have high dips or are intensely faulted; water problems due to proximity of aquifers; and coal quality problems such as excessive sulfur, ash, chlorine, sodium, etc. The demonstrated reserve base for western coal of 220 billion tons is considered misleading as it does not adequately incorporate the above parameters in estimating procedures. Current reserve base estimating procedures involve an abstraction of data from generalized resource estimates. The authors believe the reserve base should be determined independently beginning with well-known deposits, with all mining and recoverability constraints fully incorporated.

Jan 1, 1981

By P. T. Luckie

Analysis of classifier performance independently of a closed grinding circuit configuration may result in a poor match-up between the grinding device and the classifying device. This paper examines the relationship between classifier and grinding device in dry grinding circuits by employing a semi-empirical methodology.

Jan 1, 1980

By Nikhil Dhawan, Débora Moreira, Yogendra Pratap, Himanshu Tanvar

A glauconitic siltstone sample with a potash content of 10% is investigated as a potential potash source. The fine grain structure comprises potash bearing phases of glauconite, muscovite, and microcline. The as-received samples showed poor dissolution ~ 5%. Planetary ball milling was attempted for the dissociation of the underlying silicate structure for the potash release, and ~ 60% potash was obtained after 12-h milling. Mechanical activation (8 h, 60% NaOH) prior to heat treatment (600 °C, 30 min) was found successful in recovering more than 95%K values from glauconite. The final residue consists mainly of quartz, indicating a complete breakdown of the silicate matrix. The mechanical activation process followed is simple, adaptable, and less energyintensive compared to existing methods.

May 4, 2020

By L. B. Phelps

Industrial mineral production is basic to life in these United States. Production techniques of these minerals are part and parcel of the training that mining engineering educators must, and do, impart to their students. This paper deals with the basic mining engineering program required by all accredited engineering schools and the specific way the Pennsylvania Scare University presents and builds upon them. The manner in which these concepts provide the student with the necessary tools to function as a mining engineer in me realm of industrial minerals extraction is discussed.

Jan 1, 1981

By R. Bruce Tippin

because of the mineral's high monetary value and the spotty occurrence of free gold in the deposit. Setting up a plant sampling procedure by simply applying the usual statistical sampling theory was questionable. Two sampling concepts were considered in the sampling study: o a sufficient number of assays can be taken such that the average determined from these individual samples represents a known quantity of ore. o a sufficient weight of sample can be taken such that when assayed it represents a known quantity of ore. The test program included evaluation of sampling techniques, sample preparation and analytical methods. The overall sampling program is depicted in Figure 2.

Jan 1, 1985

By S. D. Bearden

China was the world’s leading producer of barite during 1995 with 35%. The United States followed with14%. India produced 9%. Other producers included Morocco, Turkey, Mexico and Germany. Domestic production of barite during 1995 was estimated to be 600 kt (660,000 st). Nevada produced 85% of the total. Georgia was the second leading barite-producing state. The United States is the world’s largest consumer of barite. During 1995, it used 1.6 Mt (1.8 million st). US reliance on imported barite during 1995 was about 63%of total consumption, according to the US Geological Survey.

Jan 1, 1996

By D. D. Eyer

New or improved technology will continue to drive productivity improvements through the next decade. In January 1988, I presented a paper titled, "Large Underground Mines of the 1990s? before the SME. I will follow some of the themes developed in that paper as modified by our experience in the past two years. In order for a coal company to be profitable today, it has had to reduce unit costs experienced in the past. This is because the current average realization, even accounting for a recent strengthening, remains below that of a few years ago. Doing business as was done in the past is not good enough. The coal industry needs to increase productivity in the range of 5-10% annually merely to stay even with rising costs. Underground productivity has been increasing more rapidly than that for surface mining. With the exception of the Powder River basin of Montana and Wyoming, underground productivity has caught up with that for surface mining in many regions of America. There are a number of technological factors which have attributed to increases in underground productivity and which should be factors in the future.

Jan 1, 1990

By Richard M. Crowell

"As thorough sampling is usually expensive, the cost of a complete job is often unwarranted, and a cheaper approximation must be substituted. The engineer should, however, weigh the situation thoroughly before subscribing to an alternative other than an accurate assay basis on which to build his conclusion." Examination and Valuation of Mineral Property. R. Parks, 1949

Jan 1, 1994

By William A. Prosser, Kyle R. Ott, Philip Rice

"INTRODUCTION The existing Baltimore and Potomac (B&P) Tunnel accommodates Amtrak (National Railroad Passenger Corporation) and MARC (Maryland Rail Corporation) service between Baltimore, MD and Washington, DC and occasional local freight service. The Baltimore and Potomac Tunnel Replacement Project proposes new tunnel construction through Baltimore, Maryland along the Northeast Corridor (NEC) that maintains connections to Baltimore Pennsylvania Station. After the Replacement Project is constructed and operational, the disposition of the existing tunnel must be determined. The tunnel could be abandoned; however, considering its location in a congested downtown, alternative uses have been considered to take advantage of this unique piece of infrastructure by repurposing it. Alternative uses for the existing 140-year-old B&P Tunnel may end up being cost effective and should be considered, as the tunnel can be made accessible to construction crews for extended periods of time that will allow for efficient work activities unlike when it is fully operational. Possible alternatives include conversion for non-rail use, rehabilitation, or complete modernization for continued rail traffic. The following paper describes the four potential fates of the conceptual designs for the existing B&P Tunnel. The four concepts include: • No Build – rehabilitate to keep the tunnel operational. • Abandonment – complete or partial sealing of the tunnel. • Adaptive Re-Use –repurpose the tunnel with sustainable building practice. • Full Rehabilitation and Modernization – bring to current fire-life safety aspects. Of the four concepts, only the no build addresses maintaining the tunnel while it is under traffic. The remaining fates address the existing tunnel after the new tunnel is operational and railroad traffic has been diverted to it. Development of these conceptual designs were provided in a concept design study (Parsons Brinckerhoff/Parsons, 2015) that supports the National Environmental Policy Act (NEPA) review process for the Project, which includes evaluation of possible alternative uses of the existing B&P Tunnel."

Jan 1, 2016