Search Documents

By G. Ahuja

Tests were conducted to investigate the effects of cyclone geometry, operating conditions, and particle size on magnetite classification. The effects of these parameters on the partition curve for narrow size fractions were studied using a 25mm diameter cyclone cleaning -150 µ m coal. Additional tests were run to investigate the effects of geometry and operating conditions on the slurry, solid, and water splits. The relationship between the relative density of the underflow stream and the relative density of separation was also investigated. This paper presents the results from this study.

Jan 1, 1994

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling both dust and gas. Redirecting all the air towards the face equally up both sides of the machine increased both the dust and gas concentrations around the machine. When all the air was redirected towards the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all the scrubber exhaust was redirected towards the face either up the off-tubing side or equally up both sides of the mining machine.

Feb 23, 2014

By Van Price

Some technical developments of the National Uranium Resource Evaluation Program which are of general application in geochemical exploration are being studied. Results of stream water and suspended and bottom sediment analyses are compared for an area near Williamsport, Pennsylvania. Variations of uranium content of water samples with time in the North Carolina Piedmont are seen to correlate with rainfall. Ground water samples from coastal and piedmont areas were analyzed for helium. All media sampled provide useful information when properly analyzed and interpreted as part of a total geological analysis of an area.

Jan 1, 1979

Considerable attention has been given to the restoration of low-level radioactive (<1000 pCl/g) sites contaminated during the early years of the atomic energy program. Current clean-up activities which involve the relocation of contaminated soils to licensed disposal sites have been shown to be very costly due to the large volumes of soils which must be excavated, transported and stored. Recent characterization studies conducted at Virginia Tech suggest that the volume of soil requiring disposal can be greatly reduced using mineral processing techniques such as classification, density separation and froth flotation. This article discusses the application of these technologies for soil remediation and describes a conceptual flowsheet for treating soil samples from two contaminated sites.

Jan 1, 1997

By Robin G. Burn

An orebody is a mining company&apos;s greatest asset; without it there can be no mine. Yet, by the very nature of the industry, orebodies are wasting assets whose progressive depletion must be balanced by continued discovery of new ore to enable both the industry to survive and the raw material demands of society to be satisfied. Although mineral exploration may be viewed as any activity which leads to the creation of investment opportunities in the mineral industry, ultimately new ore can only be generated through discovery. The process leading to discovery may involve a long chain of independent and interdependent events. It will almost always be repetitious and require the examination of many prospects or trials before the goal, a commercially successful discovery, is satisfied. Long term survival of a mining company through regular discovery of new ore, requires a continued commitment of funds and effort to mineral exploration.

Jan 1, 1984

By A. D. MacPhail

The Highland Valley Copper partnership was formed in July 1986 and was the logical result of a mine with a large ore reserve but no adequate mill, and a mine with a large, modem mill but dwindling ore reserves. The original partners -Cominco and Lornex -were joined in January 1988 by Highmont Mining Co. which contributed a two-line concentrator. During 1988/1989, the Highmont mill was moved 7.5 km to adjoin the Lornex mill, forming what is now called the Highland mill, with a current nominal capacity of 130 000 tonnes per day. The mine is located 220 km northeast of Vancouver, British Columbia and is close to four communities in which personnel make their home: Logan Lake, Merritt, Ashcroft, and Kamloops. The map in Figure 1 2.2 shows the general area. Kamloops is a major service centre and is serviced by two railways, two major roads and a regional airport.

Jan 1, 1993

By J. Pancher

"Stainless steel castings are used in abundance in the mineral processing industry. In rotary kiln-based processes, these castings are typically exposed to high loads, corrosive elements, mechanical abrasion and cyclical temperature exposure. In the processing of iron ore pellets, it is typical to use a traveling grate preheater or a straight grate furnace to heat the pellets. Both machines have a conveyor that is mainly comprised of high temperature stainless steel castings. It is these castings which are the focus of this study. The expected life of these castings can be quite short, their cost quite high and the effort to replace them very labor intensive. The goal of this study was to gain a better understanding of the failure modes of these castings. With that basic understanding, modifications to the alloy content could be made to achieve a new operational paradigm. That paradigm could be a cheaper casting, a longer lasting casting or a casting tailored to special operating conditions (for example, highly corrosive gases or sudden temperature shocks). Over the past 4 years, Metso Minerals has sought to achieve a better understanding of the failure modes through modeling, laboratory testing and sampling of used castings from various end-users. In addition, we have tested new alloys in a laboratory setting and also in the field to see how they would perform compared to the existing ""standard casting"". Our testing has revealed interesting data concerning the impact toughness, sigma phase content and formation, chloride attack and other performance attributes of various grades of stainless steel when exposed to cyclical temperatures. Interesting results were also obtained concerning the addition of rare earth elements (Niobium, Boron, etc), nitrogen and manganese to a typical ASTM A297 grade of stainless steel. To date, a few hundred test castings have been installed in iron ore pellet plants worldwide. Many of these test castings have already experienced a year or more of operation with good results.INTRODUCTION Cast stainless steels (ASTM A297 and similar) are a main constituent used in the construction of iron ore pelletizing equipment. A typical straight grate pelletizing machine would contain upwards of 160,000lbs of ASTM A297 Grade HH castings. With a typical casting lasting only two to four years, and a casting costing around $35USD, it is easy to see that the castings are a main contributor to the overall cost of producing the pellets. Grade HH and HI (see chemical composition listed below) became the “go to” materials in the 1960’s and very few changes have been made to this day (the exception being plants that switched to flux pellet production in the 1980’s)."

Jan 1, 2015

By G. A. Kordosky

LIX® 34 liquid ion exchange reagent, one of a totally new class of metal extractants, is discussed in terms of its properties. Specifically, these properties include improved selectivity for copper and greater recovery. Some comparisons to the well known General Mills&apos; LIX® 64N have been made. Particular emphasis is given to treating solutions containing very low copper values and high impurity levels.

Jan 1, 1976

By D. J. MacKinnon

Smooth, compact, dendrite-free, 24-h zinc deposits have been electrowon from zinc chloride electrolyte using a diaphragm cell. The cell consisted of sealed anode compartment con- taining DSA anodes which were separated from an open cathode compartment by Dynel cloth membranes. Fresh electrolyte was fed to the cathode compartment where zinc deposition onto an aluminum cathode was aided by air-sparging. The catholyte passed through the diaphragm into the anode compartment from which chlorine gas and spent anolyte were withdram.

Jan 1, 1980

By J. Armstrong, J. Bourgeois, S. Warren

The application of statistical analysis software programs has proven useful for investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the U.S. National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Mar 2, 2022

By Swan. J. D.

Repairing and replacing equipment damaged by corrosion and abrasion is a major cost throughout industry, especially in the coal mining industry. Careful study of corrosion and abrasion, and their causes and effects, often leads to the selection of alternative materials which can provide economies. What, actually, are corrosion and abrasion and how do they contribute to the cost of operating a coal-preparation plant? Furthermore, what can be done to alleviate corrosion and abrasion problems and thereby reduce operating costs? These questions will be answered in the following discussion, which will describe the destructive action of corrosion and abrasion and give several methods for controlling corrosion and abrasion losses, These methods include the substitution of stainless steel for carbon steel, the use of corrosion inhibitors, and the use of design to eliminate corrosion and abrasion. Examples will be given illustrating the benefits that have resulted in plant tests when these methods of controlling corrosion and abrasion were used.

Jan 1, 1970

By M. Guzman, M. Romero, S. Bravo-Thais, M. Flores

The phytoremediation method is proposed to recover valuable metals from polluted soils. In this sense, the objective of this research is to determine if it is possible to use native plants in the recovery of precious metals from abandoned mining liabilities. The tailings samples containing Au and Ag were acquired from the northern region of Peru. Two native plant species, Stipa Ichu and Cortaderia Nitida, were used. Results show that Au was recovery around 19% (1.52 mg/Kg) and 25.43% (1.78 mg/Kg) by using Stipa Ichu and Cortadeira Nitida, respectively. Besides, Ag had a better recovery in the Stipa Ichu reaching a value of 6.83% (0.628 mg/Kg); in contrast, Cortadeira Nitida had an efficiency of 3.6% (0.814 mg/Kg). Bioaccumulation, bioconcentration and translocation factors were calculated by determining the concentration of precious metals in the roots and aerial parts of each plant. Results show that Stipa Ichu had a greater capacity of hyperaccumulated Ag compared to Au; while Cortaderia Nitida tended to have a better performance for Au. In conclusion, both plants are recommended for phytoremediation of mining liabilities.

Feb 1, 2023

By J. D. McKay

Flotation columns have been readily accepted for use in most sulfide flotation plants; however, recently columns are being used in many other areas. Recent improvements in design methodologies have overcome many operating problems and led to improvements in metallurgy. In addition, physical improvements in column design have simplified their operation while leading to better control. The Turbo-Air External Bubble Generator has provided a method for bubble size control and variation in air holdup and carrying capacity. These have enabled commercial operations to improve grades and recoveries by optimizing performance.

Jan 1, 1990

By M. Adnan Goksel

The hydrothermal agglomerating process described (U.S. Pat. 3,235,371, (1966)) is different from the conventional high temperature processes. Green pellets or briquettes made with mixtures of moist iron ore concentrates and burned or hydrated lime fines are hardened in an autoclave at 198°C and under steam pressure for 1/2 to 5 hours, with or without previous drying. Under the neutral conditions, oxidation of magnetite does not occur as in the conventional processes. The resulting agglomerates are hard and resistant to abrasion and weathering, and they do not disintegrate in the Linder test. The equipment required for the process is not complicated, and favorable operating costs are projected because of the low temperature and efficient heat recuperation. A low capital investment makes the process attractive even when the annual pellet production is below a million tons.

Jan 1, 1968

By Hans W. Schreiber, Rudi P. Fronk

IINTRODUCTION Widespread activities in precious metal projects in the western U.S., Australia, Canada and other parts of the world have opened a flood-gate of consul- ting expertise to aid and accelerate the development process. Utilization of outside expertise has taken on many shapes and forms that have in some instances actually "decelerated" or "retarded" project progress. Small mines are especially vulnerable to apparent false-starts and misdirections, be- cause of their generally lower capital commitments, shorter lead times and limited mineral in-house expertise. Mine development for small mines requires fundamental approaches by knowledgeable consultants that are timely and cost-efficient and in line with accelerated development, if they are to be successful. The development process is obviously that process which brings a given deposit into production. Or, put another way, the process comprises all activities, decisions and commitments which take place from the moment an authorizing entity (usually a board of directors) com- mits to development and production (usually on the basis of a final feasibility study) until the first ton of ore is processed to a saleable product. The activities, decisions and commitments over a development period--such a period can range from as short as a year or less to as long as 5 years or more--are many, highly varied, and often interdependent. The development period is also particularly risky, not only because of the varied and interdependent decisions and commitments, but also because of capital demand amounts. Delays in the development process are thus particularly costly - sometimes so costly that small and often undercapitalized mining companies, failing to reach production and a cash flow within a planned period, face, if not bankruptcy, at least severe equity dilution or particularly onerous and restrictive covenants on additional loan financing. It therefor behooves especially small mining companies to examine ways to accelerate development. By doing so, the development process may actually meet planned scheduling. The development process generally comprises environmental impact studies completion, final engineering, permit- ting, financing, equipment and machinery procurement, contractor selection and construction -- such activities largely being overlapping. The paper addresses what the small mines operator or the small mining company can do with consulting firms to accelerate development. By "small mines" is meant open pit operations of 2000 tpd or less and underground operations of 500 tpd or less. By "consulting firms" is meant entities who do not possess an engineering and construction capability, such as Derry Michener Booth & Wahl, Pincock Allen & Holt, Behre Dolbear-Riverside, etc. The paper concentrates on gold projects. PRIORITY CONSIDERATIONS Of the items listed in the previous paragraph which comprise the development process, the two which most consistently appear to cause delays are permitting and financing. The former&apos;s delays can be due to political overtones and thus the delays may not be reasonably foreseeable. The latter&apos;s delays are most often due to inadequate preparation, and thus are avoidable. For the reason stated above, and considering that financing is fundamental to all of the activities which constitute the development process, the paper focuses on financing as the priority item which can most assist in accelerating or retarding the development process.

Jan 1, 1987

By R. K. Mensah-Biney, M. T. Hepworth, K. J. Reid

The loading characteristics of gold-bromide species onto activated carbon were evaluated using a batch system. The overall loading of gold onto activated carbon was rapid for the first few hours, but it continued without cessation as a result of the reduction of gold. Therefore, conventional equilibrium considerations were not applicable. Although loading continued slowly after several days, an abnormally high, loading capacity value of 10-12 meq/g carbon (650-800 kg Au/t) could be attained in 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of (AuBr4)- species to the external surface to be reduced to metallic gold by carbon. Elution of gold from loaded carbon was feasible provided the carbon had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical, and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon for gold-bromo species is discussed.

Jan 1, 1994

By H. T. Mikkelsen

Mineral production implies emissions of particulate matter (dust), noise and vibration that may cause conflicts with neighbors living nearby. In Norway a few conflicts has been brought to court, the latest in 2006. This paper discusses dust emissions and dust depositions (dustfall). The pollution authorities have accepted monitoring of dustfall instead of suspended dust as the first step in conflict cases concerning small and medium sized enterprises. In the case of exceeded limit values, the second step is to require monitoring of suspended dust and next the implementation of control actions to reduce dust emissions. Dustfall monitoring programmes carried out at six mineral production plants in Norway, show that the mineralogical rates of dustfall are rather low a few hundred meters away from the plants or the tailings disposal. They are mostly considerable lower than the limit value of 5 g/m²/30days accepted by the authorities. Seasonal variations between mineralogical and organic dust fractions can be observed in Norway, with higher content of mineral dust during winter time. Other sources to mineralogical dust can be recognized. During winter time wear of road pavement and sand on icy roads can give high emissions of mineralogical dust to the ambient air. Parallel monitoring of suspended dust and rates of dustfall indicate that dustfall can be used to estimate the level of suspended dust. A model for estimating suspended dust based on records of dustfall is presented.

Jan 1, 2007

By James N. Orlich

Meridian Gold Company&apos;s Royal Mt. King mine (RMK), a subsidiary of FMC Gold Company, is located approximately 40 miles east of Stockton, California on the western edge of the historic mother lode belt. Gold ore at RMK is associated with a series of northwest trending fault zones hosted in either meta-volcanic or meta-sedimentary rock types commonly referred to as greenstone sulfide and carbonaceous phyllite. Mineralogy studies show gold in both ore types to occur primarily as electrum in the form of 1 -20 um inclusions in pyrite with varying amounts of free milling gold. In carbonaceous ores, gold was not found to be closely associated with carbon. At the start of the current mining operation, three major ore resources were identified. North Pit and Gold Knoll pits were the major greenstone reserves while Skyrocket Pit contained over 60% of the total reserves as carbonaceous ore. Since North Pit and Gold Knoll were to be the first areas mined, the mill began operation in February 1989 with a flowsheet designed for greenstone ores with a carbonaceous expansion anticipated after depletion of the greenstone reserves.

Jan 1, 1992

By AMIT SHARMA, BIBHUTI BHUSAN MANDAL

This paper describes the vibration transmissibility characteristics of mining vehicle seats under dynamic conditions in an opencast iron ore mine. Magnitude and frequency contents of vibration signals on the seat floor as well as on top of the seats were measured to record the change during transmission. The conventional rigid seats were found to resonate at about 4 Hz, which coincides with the resonance of the human spine. The pneumatic suspension seats also proved to be more efficient in attenuating the overall vibration energy transmitted from the vehicle chassis to the human body.

By Robert Kimutis, Lihong Zhou, Mark Mazzella, Jim Addis

Due to the surge in shale gas production, a substantial number of unconventional shale gas wells have been drilled across U.S. coal reserves. Gas breaches resulting from damaged wells pose a considerable safety risk to miners. This paper investigates how a ventilation system can effectively manage breached gas through a network-based numerical model and laboratory-scaled physical model. Several hypothetical gas breach scenarios in a longwall area are simulated, exploring factors influencing gas mitigation. The study establishes correlations between breached gas inflow and gas concentration at critical locations. The findings in this study provide valuable insights for managing mine ventilation systems and enhancing coal miner safety.

Feb 1, 2025