Search Documents

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The U.S. Bureau of Mines and AMAX Coal Company have studied surface coal mine overburden blasting near four steel and one PVC pipe-line of 15 to 5l-cm diameter, monitoring vibration, strain, and pressure. Unlike tests simulating construction blasting, these were up to 1000 kg per delay in 3l-cm blastholes. Worst case comparisons showed that 12.7 cm/s blasting vibrations produced strains about 1/4 that of pressurization and 10-18 pct of the ultimate tensile strength. No failures occurred from blasting as close as 15 m which produced vibrations over 60 cm/s.

Jan 1, 1994

By J. A. Bradbury

N. A. Degerstrom, Inc. has constructed and operated a processing plant approximately five miles north of Soda Springs, Idaho for processing a byproduct phosphate treater dust from Monsanto's elemental phosphorus plant, also located in Soda Springs. The plant is designed to produce agricultural-grade phosphoric acid, gallium, and silver. The design capacity of the plant is 54.4t (60 st) of treater dust per day, which can produce 16,326t (18,000 st) of phosphoric acid, 6,600 kg of gallium, and 6,033 kg (194,000 oz.) of silver per year.

Jan 1, 1993

By E. L. Gillenwater

Coal mine planning has three distinct decision levels: (1) decisions made at the upper level of management that determine production requirements for specific mines, (2) decisions made at the middle management level, the mine level, that determine how the mine satisfies its production requirements, and (3) decisions made at the operating level of management, the sectional level, that determine the sequencing of machine movements at the face. In this paper, the underground production scheduling problem is formulated in multi-stages using the Hierarchical Production Planning (HPP) approach. Two linear programming HPP models for accomplishing decisions at the first two levels are developed. Both models address the aggregate production planning process. The Mine Production Scheduling (MPS) model permits determination of monthly production and inventory levels. The Section Production Scheduling (SPS) model incorporates a quality blending requirement into the determination of weekly sectional production and inventory levels.

Jan 1, 1995

By D. W. Hutchinson

One of the most important problems facing the coal industry today is the disposal of refuse from the coal preparation plants in a safe, economical, and efficient manner while complying with all legal requirements. The most commonly used refuse disposal method has been landfill/impoundment. In this method, the coarser refuse fractions are disposed of by layering and compaction into a landfill. The fine coal slurry refuse fraction is impounded in a dam constructed of a portion or all of the coarser refuse fractions. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the preparation, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically unfeasible or technically impossible. At the time of the promulgation of the new Federal regulations, United States Steel Corporation was in the process of designing the Cumberland preparation plant. As a result of the new regulations

Jan 1, 1977

By Ihor Kunasz

The high lithium demand forecasted for some high tech applications and batteries for electric and hybrid-electric vehicles, in particular, has sparked increased exploration for lithium, particularly for lithium- and potassium-bearing brine deposits. The latter have generally followed the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) NI 43-101 guidelines on resource reporting, formulated for hard rock deposits (metals and industrial minerals). While a number of the requirements can be appropriately applied to brines, brines are fluids and require a specific analysis leading to a distinct set of reporting requirements. Brines cannot be considered industrial minerals because the various elements occur as ions in a dynamic fluid, rather than being chemically bonded in a solid. Although chemicals are produced from brines, brines have no relation to industrial mineral deposits. This article analyzes the recently released (Nov. 1, 2012) document CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines, in light of the practical knowledge available from existing brine operations. It recommends modifications to the guidelines, which, if applied in their present format, will result in overstating resources and reserves and mislead potential investors. The CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines document is generally descriptive and does not fully address the methodology for brine resource or reserve definition. Lithium and other elements (potassium, magnesium) are contained in a fluid, the hydrologic characterization of which should be the principal focus of a brine exploration program. The fundamental requirement in defining lithium brine resources and reserves in a salar is the identification and definition of those formations ? the aquifers ? that will yield brine in a usable quantity to a well, because brines can only be extracted by pumping wells. Fine-grained sediments will never, as required in the summary Table 1, have ?reasonable prospects of economic extraction,? cannot be considered and, therefore, need not be tested. However, the guidelines recommend the collection of solid samples and a high-core recovery for laboratory testing of various sediments instead of focusing on the brine.

Oct 1, 2013

By C. West

Structured or embossed HDPE and LLDPE geomembranes have been available to mine owners and designers for over ten (10) years. As many owners and designers discover and demand the consistent high quality characteristics of this type of geomembrane due to the unique manufacturing process, the use of these materials in new mines, mine expansions and final closure designs has steadily increased. Structured liner materials are available for double lined and final cover systems and are revolutionizing the way ponds, pads and final closures are constructed. This paper will discuss the structured or embossed geomembrane concept and manufacturing process. Additionally, the paper will present comparative testing illustrating the major advantages of using this type of product in these types of applications. Both technical and economic advantages are illustrated. The cost savings include lower installation costs, less material used, and third party inspection times not to mention better performance. These new systems will be presented.

Jan 1, 2011

By W. A. Crosby

All mine operators using explosives want to maximize explosive performance while minimizing blasting costs. Use of bulk explosive products such as AN/FO, heavy AN/FO, slurries and emulsions has greatly improved blasting efficiency over the years. Many operators have improved energy output from these products by adding aluminum. A major problem facing them is the fluctuation in aluminum price. The question therefore becomes, when is it economically advantageous to use aluminum in bulk products? This paper answers this question by first reviewing the energy output from the main types of aluminized and non aluminized bulk mixed explosives and then by showing the relationship between the different products on a cost and energy basis. The paper finally presents examples of charts and tables which will aid mine operators to conveniently select the most economically correct bulk explosive, including the level of aluminum addition.

Jan 1, 1991

By Jorgen Elbrond

Shovels, trucks and repair bays for the trucks each play their role in the capacity of an open pit operation. It is therefore convenient to have a procedure for the capacity calculation which takes all 3 factors into consideration in a comprehensive manner. This can be done by means of a cycle model, earlier developed for the shovel-dumper circuits, when the repair facility with its number of repair bays is added as a superimposed service system, which the trucks visit at certain specified intervals. The calculation model transforms the mechanical availability of the trucks into their operational availability. The system's capacity in truckloads per shift and the trucks' operational availability of certain combinations of shovels, trucks and repair bays are shown.

Jan 1, 1981

By R. Kent Comann

The sixth survey on the mining industry by Comann Associates provided data for entry-level and midlevel engineers as well as executive officers. Average 1989 compensation - base salary and anticipated bonus - for chief mining executive officers or chief mining operating officers: $237,943. This is an increase of 20% over the results of the last survey, on 1985 compensation. The latest survey also showed that bonuses for chief mining executive officers averaged 33% of base salary. Average 1989 compensation for chief executive or chief operating officers at mining operations with under $50 million in gross sales, $148,638; at mining operation with more than $50 million in gross sales, $275,141. The survey showed that these officers averaged 14 years employment with their present company, had five years in their present position, and had an average age of 54.

Jan 1, 1990

By K. H. Lee

The rate of beryllium dissolution from a low-grade ore was studied in sulfuric acid solutions. The effect of stirring speed, sulfuric acid concentration, particle size and temperature on the rate of dissolution of beryllium was established. The results of the study showed that the dissolution rate is independent of stirring speed within the range of 250-1000 rpm but depends on 1/2 power of the sulfuric acid concentration. The dissolution rate increases exponentially with decrease in particle size and the maximum attainable rate of extraction with respect to particle size is 6.6 x 10 mol dm min. The apparent activation energy (^E) for the dissolution reaction is 54.4 kJ/mol (13.0 kcal/mol). Based on this magnitude of the activation energy, it is concluded that a surface chemical reaction is the rate limiting step for the temperature range (70° -100°C) investigated.

Jan 1, 1988

By M. E. Volin

Reagent control for optimum concentrate yield was studied by laboratory batch flotation tests simulating the Groveland plant flotation circuit in which a rougher concentrate is cleaned twice. The reagents were a fatty acid collector, a sulphonate collector and sulphuric acid. The study included two types of flotation feed representative of the reground and deslimed tailing from the spiral concentration circuit, one when the ore mineral is predominantly specularite and the other when it is magnetite. The factorial design included three levels of fatty acid, five levels of sulphonate and five levels of H2S04, with the two types of ore in nested blocks, making up a total of 75 tests. Similarity of results and reproducibility were established in preliminary tests. The final tests were performed in random order under closely controlled conditions following the established procedure.

Jan 1, 1965

By A. H. Kaksonen

Numerous reactor designs for biological sulfate reduction have been reported. Fluidized-bed bioreactors (FBR) can efficiently retain biomass and allow high mass transfer and reaction rates. This work reviews the development of various sulfate-reducing FBR processes for treating acidic metal- and sulfate-containing waters and recovering metals from bioleaching liquors. The FBR process performance was evaluated with continuous flow experiments under various operational conditions: fluidization rates, influent pH values, metal, sulfate and salt concentrations, hydraulic retention times, electron and carbon sources, and temperatures. Substrate utilization and sulfide inhibition kinetics were determined with batch FBR-kinetic experiments. An artificial neural network (ANN) model was used to predict the performance of the FBR. Sulfate-reducing bacteria (SRB) were characterized in FBRs with molecular and culture-based approaches with the aim to gain a better understating of the bioprocesses. Based on the studies, FBRs are well suited for the combined removal of metals, acidity and sulfate from water.

Jan 1, 2010

By J. A. Meech

An analysis of screen design options on the operating efficiency of secondary crushing plants has been conducted using a dynamic computer model. The model allows for the simulation of a wide variety of crushing circuits and can be run on either a microcomputer (IBM PC/XT) or a large time-sharing mainframe computer. Size reduction and separation characteristics of crushers and screens are based on standard manufacturer design and performance data. Input/output routines are available in tabular, alarm or strip chart recorder modes to facilitate operation of the program. A number of alternate circuit designs are compared to show the influence of surge capacity, screen size and area, screen deck location, and closed side crusher settings on the operation of a 10,000 ton per day plant. The program is currently in use at Queen's University to teach plant operations and control. It has potential to be a valuable tool for operator training.

Jan 1, 1985

By M. L. Harris

Explosions in underground mines and surface facilities such as processing plants are caused by confined accumulations of combustible dust and/or flammable gas mixed with air in the presence of an ignition source. Underground explosions can be prevented by minimizing methane concentrations through methane drainage and ventilation, by adding sufficient rock dust to inert the coal dust, and by eliminating ignition sources. The effectiveness of rock dust in arresting explosion propagation was proven by experiment and practice (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11). The precise mechanism by which rock dust (generally pulverized limestone dust) quenches flame has not been fully explained, but is believed to be absorption of thermal energy from the heated gases and absorption of radiant energy, which reduces the preheating of unburned coal particles ahead of the flame front. One measurable aspect of explosibility is incombustible content. In order to determine whether enough rock dust is applied, 30 CFR1 § 75.403, Maintenance of Incombustible Content of Rock Dust, requires at least 80% incombustible content on the roof, ribs, and floor of underground coal mines. 30 CFR § 75.403-1 further defines the incombustible content as follows: ?Moisture contained in the combined coal dust, rock dust and other dusts shall be considered as a part of the incombustible content of such mixture.? In order to determine the incombustible content of the mine dust, samples of deposited dust from specified areas in a mine must be collected, analyzed, and then compared with the minimum standard of 80%. The traditional low temperature ashing (LTA) approach to determine if a coal and rock dust mixture is compliant with the inerting requirement consumes the coal dust and considers the remaining material to be inert. Compliance with the law is then determined by comparing the measured percentage of inert material of the representative band sample with the pre-established requirement of 80%. The incombustible content of the sample includes rock dust, the amount of moisture as received at the lab, and the inherent ash in the coal. The LTA method is not itself a direct measure of explosibility but is a surrogate that calculates a single parameter associated with large-scale Bruceton Experimental Mine (BEM) explosion test results conducted with dry rock dust. This method assumes a homogenous mixture with no layering of rock dust and coal dust. Float coal dust is a serious explosion hazard if it accumulates on top of the rock dust and is not mixed with the rock dust (12). Mitchell and Nagy (13) studied the effectiveness of water as an inerting agent for the coal dust explosion hazard. The study emphasized that surface water evaporates readily from dusts. Thus, in a passageway where the dust is wet, changes in weather or the ventilation system could dry the dust and make it unsafe in a relatively short period of time. Where adequate rock dust has been applied, this drying effect is not a factor. However, if the mine depends upon the moisture content as part of the incombustible content, fluctuations in the dust surface moisture within a mine can render moisture content an ineffective and inconsistent measure of safety. Additionally, if sufficient moisture is absorbed and subsequently relinquished by rock dust, a cake can form and render the rock dust ineffectual. The trend has long been recognized that mine explosions occur primarily during the winter season when the humidity is low for long periods of time (14, 15, 16). In light of this trend and due to the potential variability of the moisture content of the dust, it may not be prudent to include variable surface moisture in the total incombustible content of the sample. Instead, surface moisture should be viewed as an additional safety measure as long as the rock dust is dispersible. However, moisture limits the ability of the rock dust to disperse and can significantly reduce its capacity to effectively inert propagating explosions (2, 13, 17, 18, 19, 20, 21, 22). Given the methods by which the as-received moisture and incombustible content are determined, dust samples from the 2010 MSHA database were assessed to determine the variability of the moisture content throughout a year and how often the measured as-received moisture might have affected the dust explosibility determination if removed. The findings were then verified by observation in laboratory studies and within the NIOSH OMSHR Safety Research Coal Mine (SRCM).

Feb 23, 2014

By III Sadler

Processing bauxite and clay ores to reduce Iron content to levels low enough for the ores to be suitable raw materials for such products as refractories and abrasives has long been regarded as a diffi9ult problem. Standard magnetic separation processing of the untreated ore has been attempted by previous investigators with only limited success due to the finely divided state and weak magnetic susceptibility of the iron minerals (hematite, geothite, etc.) present in these ores. The new process described in this paper consists of calcining the finely crushed ore at 500 to 800 C and then reducing (with hydrogen, carbon monoxide, etc.) the iron oxides present to magnetite or elemental Iron. The magnetic susceptibility of iron in these forms is enhanced 40-to 100-fold over that of hematitie and is readily removed by simple magnetic separation. Starting with a 2.7% Fe20s Alabama bauxite ore, a 1.5% Fe20s product was produced in one pass through a Davis tube magnetic separator with 95 + % recovery of the iron-free bauxite fraction and a 20% Fe20a magnetic product. These findings suggest that with the addition of light calcination, reduction and magnetic separation steps to the conventional refractory grain production process, the large U.S. reserves of high-iron bauxites could be used.

Jan 1, 1990

By Jean-Marie Deschamps

In an approach to the complicated study of bauxite from Les Baux de Provence it is necessary to consider the paleogeographical context of all the bauxites in southern France. These bauxites are of Karstic type, belonging to a metallogenic area extending from the Pyrenees Mountains to the Alpine Massif. Within this area each deposit does not always correspond to the same geological period. There are differing opinions regarding the origin of Karstic-type bauxite and a discussion of these various theories is beyond the scope of this paper. Bauxite of Les Baux, in Provence, was discovered in 1821 by the chemist, Berthier, near this picturesque village located in the region of Arles. It is Les Baux from which the name of bauxite originates. For a long time this bauxite was of no interest because of high silica 'and mediocre alumina content. Besides, the calcium carbonate content is somewhat high and is one of the main characteristics of Les Baux bauxite. The problem of exploration of the Les Baux deposit has been to prospect minable zones according to traditional norms where silica and carbonate are low.

Jan 1, 1977

By E. Oraby, S. Garcia, A. Thurgood, D. Bertoldi, G. O’Malley

Mining and Process Solutions (MPS) most advanced process, GlyCatTM is the only process that can be easily adapted to existing cyanidation plants in the market today whose real advantages over cyanidation are when treating copper containing ores, concentrates or tailings. With such complex material, GlyCatTM requires 70-90% less cyanide addition to achieve the same precious metal extraction. However, GlyCatTM is not simply cyanidation with added glycine. It is a completely different process where the solution chemistry and conditions needed to effectively leach the precious metals are quite different. Downstream however, the process is largely unchanged as the recovery of the leached gold and silver uses existing known processes such as conventional activated carbon or zinc cementation (Merrill-Crowe process). Another advantage is lower SCN, OCN, WAD and no free cyanide in the effluent which can substantially reduce cyanide detoxification requirements and decrease the OHS and ESG risk of the operation. This paper outline some of these differences and presents testwork, piloting and process examples to highlight the advantageous of this new process over conventional cyanidation.

Feb 1, 2023

By S. Frisch

Selenium (Se) in effluent waters has become a significant challenge for a number of industries. Toxicity studies and new reports of occurrence have certainly caused increased scrutiny and actions in the mining industry today (Sandy, DiSante, 2010). While initial activity in addressing selenium-laden waters were conducted in the coal mining industry, today a much broader range of mine types are beginning to search for solutions to selenium treatment of their mining waters, including both hard rock mining operations (gold, nickel, zinc, etc.) and soft rock mining (phosphate, uranium, etc.) Throughout North America, new regulations covering selenium discharge are either in place or being developed. While a number of physical/chemical approaches show promise in selenium treatment, when considering optimal cost and treatment efficacy issues, biological treatment ? particularly fixed-film biological treatment - is reported to be one of the most promising approaches to managing selenium-containing waters. Among biological treatment options, the fluidized bed reactor (FBR) has undergone extensive pilot testing for Se treatment in the last three years, including eight pilot programs, and the first FBR system is now operating at a coal mining site. In all tests, the FBR has been shown to be a highly cost-effective approach to selenium treatment based on its physical and performance characteristics. This is consistent with its history for reaching low levels of treatment in similar service for other oxyanions including perchlorate, nitrate and various metals. With the results from the most recent testing, the technology has been shown to be adaptable to an ever-broadening range of influent water conditions and flow rates, in varying terrains and weather conditions. Selenium occurs in various valence states from -2 to +6 (Sobolewski, 2005). The speciation of selenium plays a critical role in understanding the effectiveness of any approach for removal, especially to low levels. Elemental selenium is insoluble and has little effect on living organisms. Colloidal fractions are known to occur. In aqueous environments such as coal mining runoff, selenium is most often found as the oxygenated anions of selenite (SeO32-, Se4+) and selenate, (SeO42-, Se6+). Selenium is commonly found in mining waters in concentrations ranging from 3 to >12,000 µg/L. The U.S. National Primary Drinking Water Standard MCL is 50 µg/L for selenium (EU 10 µg/L; WHO 40 µg/L). The National Fresh Water Quality Standard is 5 µg/L for selenium. The U.S. Fish and Wildlife Service has recommended that the National Fresh Water Quality Standard be lowered to 2 µg/L to protect fish, waterfowl, and endangered aquatic species. Several states have followed with enforcement actions at these same low levels. In Canada, permits may require stakeholders to monitor levels in water or biota, or to comply with guidelines, at either the National or Provincial levels, which can be as low as 1 or 2 µg/L in surface waters. Treatment of selenium in all mining waters presents a series of challenges. It can be present in relatively dilute concentrations and in streams with variable and often high flow rates. It can be present in many soluble and particulate forms, which may affect process design and treatability. The conditions of influent selenium-containing waters can vary, with issues such as temperature, pH, total dissolved solids and other contaminants affecting the ability to remove selenium selectively and economically. Treatment of selenium often results in the generation of a concentrated by-product requiring disposal, and re-release from residuals can occur. Beyond these issues, the physical environment of a mining operation can offer challenges such as remoteness and harsh and/or cold weather. Currently available selenium treatment technology (Table 1) includes biological treatment and a number of physical-chemical processes ? such as ion exchange, membrane filtration and adsorption ? that vary widely in efficiency and cost. Most treatment options remain either too costly and/or unproven for selenium-containing streams for reasons that include poor removal efficiency, variability in volume and composition of influents, system sizing and logistics considerations, as well as operating requirements.

Feb 23, 2014

By J. P. Morgan

The Vesta Preparation Plant of the Jones & Laughlin Steel Corporation is located on the Monongahela River, eight miles south of Brownsville, Pennsylvania. This plant is capable of cleaning 2400 NT/hr of a mixture of Pittsburgh seam high volatile coals from the Vesta and Shannopin mines to produce a metallurgical coal of 6.75% ash and a steam coal containing 14% ash. Heavy media vessels are utilized to upgrade the coarse coal while launders and tables. handle the -1/4" fraction of the raw coal feed. Cleaned -coal goes to boot classifiers where the +48 mesh material settles and is removed by bucket elevators. This 1/4 x 48 mesh material is then sent to centrifugal driers for dewatering. As designed, the minus 48 mesh fraction overflows the boot as a 7 to 8% solids slurry and is recovered by cyclones and a thickener and dewatered by filtration. The-products of the heavy media circuit, the launder-table-boot-drier circuit and the cyclone-thickener-filter circuit are combined to constitute the shipped metallurgical coal. This Vesta-Shannopin mix is combined at J&L's Pittsburgh and Aliquippa Works with purchased low and medium volatile coals for the production of metallurgical coke.

Jan 1, 1962

By Stephen C. Moore

The Grossschloppen vein-uranium deposit, Bavaria, West Germany, was examined utilizing underground workings during 1980-82 by Esso Erz GMbH, an affiliate of Exxon Minerals Company (EMC). Geologic evaluation entailed dense drilling of a portion of the deposit from workings constructed specifically for the program. Discovered in 1977, the deposit was initially explored by surface diamond drillholes which allowed definition of a 30-60 m wide vein system discontinuously mineralized along a 1000 m strike length and to at least a 450 m depth. The underground program was conceived as a cost effective procedure to answer questions on vein correlation, grade continuity and variability. A 1200 m decline allowed access for detailed sampling of approximately 10% of the known area of mineralization. Fanned drillholes, logged by gaga probe, were spaced to provide intersections of veins at 10 to 20 m intervals. Six cross cuts also penetrate the pitchblende and uranophane mineralization which occurs in 0.1 to 2.5 as thick quartz veins. Detailed cross-sections and level plans were constructed for resource estimates of the intensively studied portion of the vein system. The program resulted in the discovery of local, high grade areas and an average grade in the evaluated area nearly double that expected from surface drilling.

Jan 1, 1983