Search Documents

By Ernest E. Thurlow

"Western Coal" in this paper is limited to those deposits of subbituminous coal and lignite in the States of Montana, Wyoming, and North Dakota. The characteristics of the coal are discussed as well as the history of mining and current mining operations for steam coal. The future of the region is tied closely to the ultimate conversion of coal to oil and gas products. Problems of industrial water supply and environmental considerations are covered together with a brief review of current legislation's actions affecting strip mining.

Jan 1, 1973

By S. Daniel Thompson

In underground coal mining, the specification and control of belt and bunker capacities are complicated by (1) stochastic and intermittent conveyor loading, (2) a limited ability to reduce surge at the mine face, and (3) occasional overlapping of loading from two or more mine faces on the conveyors. Recently, because of longwall mining and other factors, the capacity requirements of most mine conveying systems have risen substantially; as a result, efficient capacity design and control have become important mine planning issues. This paper reviews these design issues and their associated modeling procedures. Design considerations and modeling difficulties are also examined.

Jan 1, 1996

By A. Noble

"Linear circuit analysis (LCA) is a fundamental tool that may be used to evaluate, design and improve the performance of mineral separation. The traditional LCA methodology provides a comparative evaluation of circuit designs purely from the unit interconnections. The quantitative approach uses the analytical circuit solution to evaluate the slope of the circuit’s partition curve at the midpoint. Since the partition slope is often associated with a separation’s general selectivity, this numeric value is used to compare and rank alternative configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. By itself, this value does not account for the relatively high unit dollar value of pure material or the gains and losses in mass yield associated with alternative circuit configurations. Realizing the value in the LCA methodology, but respecting the limitations of the partition slope valuation, the authors have derived two new performance indicators that quantitatively address pure particle misplacement (the Partition Moment of Inertia) and circuit mass yield (the Yield Score). Together, these parameters provide a better indication of separation economics in typical mineral and coal separation systems. Since the two parameters provide independent information on circuit selectivity and circuit yield, a Pareto efficiency, multi-objective function selection approach is proposed for preliminary circuit selection.IntroductionOver the past 30 years, numerous scientific and industrial studies have proposed various mineral processing circuit design methodologies that attempt to optimize the allocation of separation resources within the processing plant. Over this period, the methodologies have undergone various transitions, including the increased inclusion of process models and computationally intensive algorithms, as well as a general shift from a purely technical solution (Lauder and McKee, 1986) to partially economic solutions (Abu-Ali and Sabour, 2003; Cisternas et al., 2014). Today, circuit design is largely driven by flowsheet simulation; however, no consistent design methodology is used across the industry.One intriguing approach for circuit evaluation is linear circuit analysis (Meloy, 1983a). This method evaluates the separation potential of the circuit solely considering the unit configuration and stream interconnections. No preliminary data other than the basic circuit configuration is required to use the approach."

Jan 1, 2015

By F. Sill

The disposal of residual material from processing and combustion of coal, from incineration of domestic refuse and sewage sludges kind to the environment is a prior task for the future. Deutsche Montan Technologie (DMT) has developed a new technique which makes possible to fill-up goaf cavities behind running caving systems in coalmining. In a mixing and pumping station on the surface high concentrated suspensions are produced from the above mentioned materials. The paste is pumped through pipes to the coalfaces and via trailing discharge pipes stretched to the fracture zone in the caved-in goaf. Since three years a special designed plant is working successfully on a coal mine of Ruhrkohie AG.

Jan 1, 1994

Satisfactory means of managing growth in boom towns is a concern in mineral, energy and other large industrial developments. This session will include examinations of socioeconomic impacts, major issues such as social disruption, case studies, methods of managing growth, and concerns involving Indian lands. Innovative methods will be offered to assist the public, government, and industry in finding solutions to managing growth in rapidly growing communities.

Jan 1, 1979

By G. V. Campbell, O. T. Holdsworth, M. G. Nelson

A senior design project is required by all accredited mining engineering degree programs. Often referred to as the capstone of a student’s education, this project is expected to include all the important components of the preliminary economic assessment of a mineral prospect, including orebody modeling, grade and reserve estimation, selection of mining and processing methods, preliminary mine design, access and utilities, environmental compliance and reclamation, and financial analysis. Two of the authors (Campbell and Holdsworth) completed a senior project in 2021. They analyzed the Akie zinc deposit located in Canada. This paper summarizes the economic analysis portion of that project. The two primary objectives of this economic analysis were risk reduction and integration of economics and engineering. Addressing risk is important as risk is one of the primary concerns in mining investments. Risk reduction was the primary concern through the entirety of this economic analysis. Integration of financial analysis and engineering design was the first component of a risk reduction design. This allowed for financial and engineering design to be optimized in conjunction with one another. This produced benefits from both a financial and an engineering prospective. From a market, economic, and financial risk perspective, risk was reduced by forecasting multiple metal price scenarios, and then addressing the Akie project’s economic viability at each price point. Lastly, risk was address through consideration of nontraditional financing options. The project also sought to minimize financial and human capital risk, by proposing mutually beneficial cooperative social relationships and favorable work, schedules. Description of that work is not included in this paper.

Mar 2, 2022

By S. Lu

The particle-bubble attachment and the rupture of formed aggregates in flotation cell were investigated in terms of turbulent regime. It was found that the particle-bubble collision rate is closely correlated to the energy barrier between particles and bubbles, and no adhesion takes place for the hydrophilic particle-bubble system due to the introduced ?capture efficiency? f(a) being zero. The values of an especially defined Weber number, i.e. the ratios of turbulent stress to aggregate strength in the inertial subrange of turbulence were estimated, the results showed that the detachment of a particle from a bubble involved in an aggregate is mainly caused by the turbulent stress only in the impeller zone, no bubble splitting occurs both in the impeller zone and in the bulk zone.

Jan 1, 1993

By B. A. Slaker, T. Miller

"An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys, to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in) was measured by the extensometers, photogrammetric reconstructions, and laser scanner over a 6-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls was significantly lessened. INTRODUCTION Limestone formations in the United States can be subject to relatively high horizontal stresses due to the presence of tectonic loading of the strata. Horizontal stresses have a documented history of causing stability issues in underground limestone mines. Kuhnhein and Ramer (2004) discussed the influence of horizontal stress on complex ground control interactions associated with limestone pillar design and mine layouts. Esterhuizen et al. (2008) documented roof damage observations associated with high horizontal stresses such has roof guttering, beam instability, oval-shaped falls, and failure propagations. There have also been a number of documented case histories of horizontal stress causing unexpected roof and pillar failures at shallow depths (Stacey and Yathavan, 2003). To the knowledge of the authors, there has only been one well-documented case of floor failure causing stability issues in an underground limestone mine. Murphy et al. (2015) documented the role that a weak, moisture-sensitive floor had in the development of a massive roof collapse. For this paper, the study site neighbored, and was in the same general geology of, the site in Murphy et al. (2015). However, the weak, moisture-sensitive floor was not present for the current study. The current study site has experienced significant floor instabilities caused by high horizontal stresses. The instability area was monitored using two different methods to determine if the floor failure would eventually propagate into roof or pillar failure. The objective of this paper is to analyze displacement monitoring measurements from string potentiometers and remote sensing techniques in an area experiencing active movement. Based on the measurement trends and observed damage from inside of the mine, the presumed failure process will be discussed."

Jan 1, 2017

By J. Frostiak

The Campbell gold operation of Placer Dome Inc. produces an arsenopyrite-sulphide concentrate which must be treated either by roasting, biooxidation or by pressure oxidation to obtain high gold recoveries. Pressure oxidation is a proven process and has the inherent advantage of meeting the stringent environmental regulations in the province of Ontario. A comparison of biooxidation and pressure oxidation was completed early in 1990 and the latter was selected by Placer Dome as the preferred process for replacement of the roasters. The commercial plant design was based on technology supplied by Sherritt Gordon and in July of 1991, the existing roaster operation was shut down and a new pressure oxidation plant was commissioned. The following summary describes the start up of the new facility and presents typical operating data.

Jan 1, 1992

By C. H. Grant

The Dew Chemical Company has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which Dow is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of non-metallized explosives currently being used. Early in 1960, we acquired additional patent rights from independent inventors and decided to set up a development station at Virginia, Minnesota, to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the bore holes. Due to the complexities involved in controlling the manufacture of the explosive in the bore hole, performance was sometimes in doubt. Furthermore, our experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation, and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over two thousand charges of eight to 60 pounds under water and in taconites and granites with many types of explosives, we have developed a metallized explosive which is now being manufactured at a pilot plant in Virginia, Minnesota, and is being evaluated commercially.

Jan 1, 1963

By Richard F. Hammen

Mineral extraction from sulfide ore deposits usually leads to the combined action of oxygen and water on the newly exposed ore. The result is acid mine drainage, a low pH solution of various metal sulfate salts and sulfuric acid. Paradoxically, the valuable metals dissolved in acid mine water are a liability because they are too toxic for discharge but too dilute to recover economically. The expense of compliance with water quality release standards has reduced the profitability of many mining operations. Solid phase extraction (SPE) columns have been developed to extract metals from acid mine water. These columns are designed to remove the toxic elements from water and recover the metals as purified fractions. This article describes the results of a Phase 1 bench-scale project to test the performance of the SPE columns. The tests were conducted with water collected from the abandoned Berkeley Pit copper mine in Butte, MT.

Jan 1, 1993

By M. F. Werneke

Flotation of the carbonate, oxide and silicate minerals of copper (malachite, azurite, chrysocolla) has been the subject of much research in recent years, but few effective solutions to this problem have been found. With decreasing reserves of sulfide minerals, the economic recovery of these "oxides" appears to be an important source of copper for the future. Xanthates have been known for many years to be malachite collectors (1), but only at very high dosages, or at lower dosages following activation of the mineral by sulfide ion. Dewitt and Batchelder (2, 3) found that chelating agents such as certain oximes were collectors for malachite and azurite, but also required high reagent dosages. Fuerstenau (4) has suggested, for example, that potassium octylhydroxamate may be an effective collector for malachite, On the other hand, Balberyszski (5) has found that oxide minerals may be completely sulfidized at high temperatures with gaseous sulfur or H2S, and then floated with conventional collectors. None of the above approaches appear to offer an economically effective method for the direct flotation of these oxide minerals.

Jan 1, 1977

By Lynn Huntsman

INTRODUCTION The Sunnyside mines of Kaiser Steel Corp. are lo¬cated on the west flank of the Book Cliff Range, a tongue of the Wasatch mountain range in Utah. The mines are 193.12 air km (120 air miles) southeast of Salt Lake City and 40.23 km (25 miles) east of the town of Price. The area has a semiarid climate with an an¬nual rainfall of 304.8 to 381 mm (12 to 15 in.) and a temperature range of -23.3 to 32.2°C (-10 to 90°F). The base of the Book Cliff Range is approximately 1981 m (6500 ft) in elevation with some mountain peaks in excess of 3048 m (10,000 ft) (Fig. 1). The Sunnyside mines were opened in the late 1890s and have been operated continuously since that time. Kaiser Steel leased the No. 2 mine in 1942 and pur¬chased the entire property in 1950. There are three mines adjacent to one another, each with its separate access, ventilation, and haulage. The three mines en¬compass an area extending 12.87 km (8 miles) along the outcrop and dipping northeasterly 2.41 to 3.22 km (11/z to 2 miles) into the Book Cliffs. During 1975, only the No. I and No. 3 mines were operating to sup¬ply 908 184.7 t/a (1,000,000+ stpy) of clean coal to the Kaiser Steel mill at Fontana, CA. Sunnyside coal is blended with coal from the Kaiser Steel mine near Raton, NM, and with purchased coal from noncompany sources to form the mix for the coke ovens. At that time, Sunnyside operated three longwall units and five to seven continuous miner units. Typical production for that time came from one miner unit pillaring an area not conducive to longwall mining; one or two miner units on construction or modernization projects, and the remaining units used to develop future longwall panels. Longwall mining has been a part of the Sunnyside scene since 1961 when the first panel was set up in the lower Sunnyside seam of the No. 3 mine. Through 1975, 27 longwall panels were mined (Fig. 2). Of the more than 47 173 604 t (52,000,000 st) of clean coal that were taken from the property through 1975, 6 350 292.9 t (7,000,000 st) were mined by longwall methods. Coal was brought to the surface in 4.5-t (5-st) mine cars and crushed to -152.4 mm (-6 in.) before entering the preparation plant. Coarse coal is cleaned by Baum jigs and fine coal (-28 mesh) is cleaned in flotation cells. The coal is reduced to 50.8 x 0 mm (2 x 0 in.) and belted to an aboveground storage pile with a ca¬pacity of approximately 113 398.1 t (125,000 st). The coal is gravity fed through two 1.52-m (5-ft) diam culverts directly into railroad cars, which pass beneath the storage pile through an arched excavation. Eighty-four 90.7-t (100-st) cars make up a unit train which makes the round trip to the steel mill in four days. Additional trains are scheduled in as demands dictate. Loading rates in excess of 13 607.8 t/h (15,000 stph) have been attained. Geology The coal seams of this area are of Cretaceous age and are classed as a medium volatile bituminous coal. coal, with a sulfur content less than 1 % and 6 to (20-mile) zone of the Book Cliffs, and this area is owned or under lease by either Kaiser Steel or US Steel. Coal in adjacent areas is noncoking but an excellent steam coal, with a sulfur content of less than 1 % and 6 to 7% ash. Sunnyside coal contains 40% volatile, 53% carbon, less than 1 % sulfur, and 51/2 to 61/2 % ash after washing. There are two minable seams throughout most of the Sunnyside property known locally as the upper and lower Sunnyside. Separation between the seams varies from less than 300 mm (1 ft) near the southern boundary adjacent to the US Steel Columbia mine, to over 12.19 m (40 ft) in areas of the No. 3 mine in the center of the Sunnyside property. The upper seam varies in height from 1.2 to 1.98 m (4 to 61/2 ft) while the lower seam varies in height from 1.52 to 4.28 m (5 to 14 ft) in areas of No. I mine where the two seams apparently come together. The majority of early work was con¬centrated in the upper seam which has a stronger roof and a lower sulfur content. When Kaiser Steel began mining the No. 3 mine in the early 1950s, it mined in the lower seam beneath the old workings with conven¬tional and continuous mining equipment. Numerous bounces and pressure points created by unextracted pillars and barriers in the upper seam made this a low¬production, high-cost mine and brought about the ad¬vent of the first longwall system. The first unit, while small by today's standards, successfully mined panels that had been all but given up and saved the mine from closure. There were areas that could not even be mined by longwall because of the erratic extraction in the upper seam. The system was successful enough to allow operations to gain access to and develop virgin areas of the upper seam. Development of longwall mining in the No. 3 mine has been confined to the upper seam since late 1964. With the almost complete extraction afforded by the longwall system, it is felt the lower seam can be successfully worked in future years (Fig. 3). In most of No. 1 mine, only the lower seam (or lower seam and upper seam combined) is minable, except in the northwest portion where a rock split has again separated the seam into two 1.83 to 2.13-m (6 to 7-ft) thick beds. In this area, the upper seam or upper split is being mined. The separation between seams at the present workings in this area varies from 0.609 to 6.1 m (2 to 20 ft). It is hoped that most of the lower split can be mined using shield supports and/or what¬ever new technology is developed in the coming years. The coal seams in this area dip to the northeast at an average grade of 10%. The dip near the outcrop reaches 22% and gradually decreases downdip. Over¬burden ranges from a few meters at the outcrop to 762 m (2500 ft) over some of the deeper workings. In the next several years, some overburden will be in excess of 914 m (3000 ft) as the lower mine workings extend ever deeper under the Book Cliffs. To cope with the

Jan 1, 1982

By W. G. Pariseau

A study of coal pillar strength at the Beehive Mine in central Utah was done in the 1970s. This study was a cooperative effort by the University of Utah, RE/SPEC, Inc., and the American Coal Company and was funded by the U.S. Bureau of Mines. Mine measurements of closure at 117 points and pillar stress using 119 vibrating wire stress gauges were made during retreat mining in this room-and-pillar operation. Laboratory testing for the strength and modulus of 372 coal cylinders up 0.3 m (1 ft) in diameter and 0.6 m (2 ft) in length was also done. Two-dimensional finite element model analyses complemented the study. However, the real world of mining is three-dimensional and in consideration of the significant advances in computing power since the time of the original study, a revisit of the data seemed warranted. In this regard, a novel finite element method was used that allows for the whole-mine analysis of tabular excavations on the kilometer scale and yet enables details to be obtained at pillar walls on the meter scale. The effects of material properties variability in situ and of joints can also be taken into account. Results that compare computed two- and three-dimensional seam-level closures with mine measurements show noticeable differences; three-dimensional results are reasonable, while two-dimensional results overestimate closure by nearly a factor of two.

Jan 1, 2014

By T. J. Crebs

The latest estimates compiled by the Society of Exploration Geophysicists again indicate a moderate increase in mining geophysical activity in 1980 over the 1979 level. While North American activity remained at above the 1979 level, a considerable increase in mining geophysics was reported in South America, Australia, and the Far East. The total worldwide expenditures for mining geophysics were reported to be $53.7 million in 1980, compared to $44.4 million in 1979, and $31.6 million in 1978. During 1980, approximately 2% of all dollars spent on geophysics were attributed to mining geophysical activities; this percentage has remained relatively constant in recent years. Airborne surveys accounted for 51% of the total worldwide mining geophysical expenditure, 43% was spent for land surveys, and 6% for borehole surveys. Within the US, the breakdown of expenditures for land surveys was 60% for elec¬trical methods, 23% for gravity and magnetic methods, and 17% for seismic techniques. Electrical techniques remain the primary exploration tool for US mining geophysicists. Electrical Methods With inductive or electromagnetic (EM) techniques, significant developments were achieved in both frequency-domain and time-domain systems. Work continued on increasing the signal level on most time-domain (TEM) methods, to increase the exploration depth. The Crone group increased the power of its Pulse ElectroMagnetic system (PEM) to a 20-amp transmitter-loop capability. The GEOEX group is modifying the SIROTEM II system to obtain larger transmitter amperage from a portable motor generator. Geonics developed a new digital recording system (data logger) for its EM-37 system. This development should increase the productivity of EM-37 crews. A new ground, frequency-domain EM system was developed by the Scintrex group. This novel Genie system does not require a wire link between the receiver and transmitter. Because an amplitude-ratio is measured, the Genie data are reported to be relatively insensitive to coil orientation and distance errors. This new technique does not need extensive line-cutting or accurate station-chaining and would appear to be a good reconnaissance instrument. Scintrex also began marketing the new IPR-11 induced polarization spectral receiver. This receiver is microprocessor controlled, and can output to a cassette tape and record 10 windows of secondary voltage decay simultaneously from up to six receiver dipoles. The Phoenix group's new 100 kW induced polarization/resistivity (IP/R) transmitter began tests using their IPV-3 multifrequency, multichannel receiver. While this unit was primarily developed for "oilfield" IP exploration research, it has obvious application to "deep" mineral exploration. The Phoenix group also developed a new remote-reference, real-time magneto-telluric (MT) device in 1981. This five-component MT sys¬tem has a frequency range from 0.0005-384 Hz. Helicopter-borne electromagnetic (HEM) developments also continued in 1981. The mining in¬dustry increased its use of the new Geonics EM-33-3 multifrequency, multicoil instrument. In 1981, the Dighem group developed software for estimating magnetite as a mapping parameter from its HEM system. Dighem's work is said to complement airborne magnetic intensity surveys, since the HEM estimate is independent of remanent magnetism and magnetic latitude effects. Gravity and Magnetic Methods Probably one of the most innovative techniques in geophysics in 1981 was the use of airborne gravity surveys for both mining and petroleum exploration. The Carson group is using a modified, shipborne LaCoste-Romberg platform in helicopters. Data accuracies to 0.5 milligal have been achieved by flying gridded surveys. Although this airborne method is expensive-up to $186/ km ($300/line-mile)-the geophysical community has been excited by initial results. On the ground, the portable proton-precession magnetometers are becoming sophisticated. Both GeoMetrics and EDA recently introduced field magnetometers having data storage and processing capabilities. This development should greatly increase the productivity of ground-magnetic surveys. Seismic Methods Development of high-resolution seismic techniques continued in 1981. These techniques have primarily been directed toward coal studies for fault detection. OYO Instruments introduced their McSEIS-1500 seismic data acquisition system in 1981. This device contains a 24-channel recording capability, with digital output to 256-kbyte floppy disks. The high-speed data transfer using the disk media is considered a desirable feature. Borehole Methods The general decrease in uranium exploration, where borehole logging is extensively used, probbly led to the overall decline of geophysical logging activity in the minerals industry. However, a number of new sondes and logging systems were introduced in 1981: • Mount Sopris recently introduced their Series III logging system. This microprocessor-controlled unit records up to four channels of data on nine-track or cassette magnetic tape. The logging package is relatively light-weight, so helicopter transport to mountainous or roadless exploration sites is possible. (Both the Edcon and Woodware-Clyde consulting groups offer "slinging" capabilities for their Mount Sopris units.) Mount Sopris is continuing work on their 500-mm-diam (2¬in-diam) spectral gamma-ray sonde. This tool is expected to be available soon. • Owl Technical "slim-downed" its successful digital deviation probe to 380-mm (1.5-in) outside diameter. This new sonde will also measure inclinations up to 80° from the vertical, as compared with its older instrument that could measure inclinations to 30°. • A magnetic susceptibility sonde was introduced in the US by the OYO Instruments group. This Kappalog sonde contains two aircored coils for measurements slightly affected by thermal changes within the borehole. The increased activity in massive-sulfide exploration and the need to "look" deeper no

Jan 5, 1982

By Mary E. Learmont

Grinding with steel media adversely affects the flotation response of galena. Electrochemical measurements, flotation tests, and AES, XPS, and STEM examinations were employed to identify interactions between galena and mild steel. Iron oxide, hydroxide, or sulfate species that formed on the galena surface upon contact with mild steel decreased its floatability, with the time of contact and aeration condition affecting the severity of the flotation depression.. Parallel tests performed with an active metal, magnesium, indicated that floatability was also affected by the presence of a surface coating involving lead species.

Jan 1, 1984

By David N. Hedges

This paper discusses the actual recovery and installation of a longwall in a bituminous coal mine in Western Pennsylvania. The coal bed mined is in the Lower Freeport seam which averages 42 inches (1.07m) in height locally. Drainage from the mine is approximately 3.5 million gallons of water per day (13.25 million liters per day). This water deteriorates the mines predominately fire clay bottom making it extremely difficult to move equipment. Support removal is accomplished by pulling the 6 ton (5443 kg) shields out under their own hydraulic power and transporting them by track over four miles (6437m) co the next longwall panel. This paper also discusses the changes that will be made to aid in the succeeding longwall recoveries and installations.

Jan 1, 1984

By David Hanson, Sean Warren, Chaparral Berry

"Coal bumps, also referred to as dynamic failure events or coal bursts (Lawson, Weakley, and Miller, 2016), continue to be a hazard in underground coal mines. While current design methods have significantly reduced the occurrence of coal bumps, they have not been completely eliminated. This paper investigates a correlation between coal compositional components, coal molecular structure, and probability of coal bumps in an effort to deepen understanding of coal behavior in an effort to reduce hazards in underground coal mines.Samples from the Penn State Office of Coal (PSOC) Department of Energy Coal Samples (DECS) were obtained for Fourier Transform Infrared Spectroscopy (FTIR) analysis using the KBr pellet method. Peaks indicative of the coal molecular structures were obtained using spectral integration software. These data, combined with published elemental data, were compared to historic bump occurrence in order to establish a possible correlation. Finally, results based on multivariate analysis of the elemental and FTIR data with bump status as the dependent variable suggest that elemental sulfur and molecular structure can be used as an indicator of bump susceptibility within the sample set considered.INTRODUCTIONThe study of coal requires consideration of multiple variables: percentages of organic and inorganic components, organic component origins, coal age, pore structure, cleat density, elemental composition, etc. Examining coal in situ increases the number of variables, such as coal depth, seam thickness, surrounding stratigraphy, and so forth. This collection of variables influences the subsequent behavior of coal simultaneously, and weighing their relative impact is a challenge for researchers. “A problem never exists in isolation; it is surrounded by other problems in space and time” (Ackoff, 1956). Having a substance such as coal that we know so much about, and yet so little, we have to ask what can be learned.An experimental study using Fourier Transform Infrared Spectroscopy (FTIR) was undertaken to determine if the chemical structure of coal contains information which may lead to a better understanding of triggers or attributes which may, in turn, lead to an increased probability of a dynamic failure event. While a full analysis of the factors driving dynamic failure are beyond the scope of this study, it is possible that a better understanding of the chemical structure of coal will lead to an increased knowledge of its inherent behavior, including its propensity to burst."

Jan 1, 2019

By Ralph H. Light

The recent surge in demand for uranium in the United States, accompanied by a significant increase in price, has resulted in exploration, mining, and milling of lower grade ores than have been exploited in the past. To sustain production levels of uranium with lower grades of feed requires larger tonnage mill operations. Also, because of recent environmental regulations, mill operations must be prepared to properly contain large tonnages of tailings, and recycle, treat and discharge, or evaporate mill effluents. Thus, the advent of lower grade ores, larger tonnage mills, and environmental considerations has made the cost of milling a critical factor in today's uranium production economics in the United States. Three basic milling methods are employed for extracting uranium from ores: 1. Acid leach, countercurrent decantation, and solvent extraction. 2. Acid leach, resin-in-pulp, and Eluex. 3. Alkaline leach, solid-liquor separation, and precipitation. Vanadium often occurs as a valuable by-product in ore deposits located in the Uravan mineral belt in Western Colorado. Also, lesser amounts of vanadium may occur in ores from South Dakota, New Mexico, and Utah. Vanadium is usually extracted in the acid leach solution with uranium and recovered by solvent extraction after recovery of the uranium. By-product recovery of uranium from phosphoric acid and porphyry copper dump leach solutions is now receiving considerable attention. Pilot plant studies are under way and construction of commercial plants is in progress.

Jan 1, 1977

By G. Wheeler

Epithermal gold exploration in the last decade has developed useful models for exploring new ore districts in Oregon. In Eastern Oregon, disseminated gold occurs in epithermal deposits that have been pervasively silicified and brecciated. Many gold prospects staked since 1980 are in fluvial and lacustrine sandstone and conglomerate deposits. Clay alteration products and disseminated pyrite may be present. Vein filling calcite and thin to thick quartz veins are common. Late stage quartz forms pseudomorphs after calcite in many deposits. Arsenic, mercury and gold are geochemically anomolous but silver is usually not. The epithermal deposits are located in part of the Deer Butte Formation or equivalent units. Exploration criteria include the presence of Deer Butte Formation or correlative units and NW structures cut by N-S basin and range structures.

Jan 1, 1987