Search Documents

By W. J. Kennedy, John D. Gardner

Introduction During the past 10 years, energy costs in mining have risen from about 4% to as much as 25% of total production cost. When combined with declining ore grades, these costs exert inordinate stress on mine productivity. Industrial engineering techniques have traditionally been aimed at improving manufacturing facilities productivity, but they have been applied to mining as pressure for productivity improvement has increased. These techniques can perform four useful functions for mining operations by improving methods, equipment selection procedures, energy use through scheduling, and managing energy costs rather than being managed by them. This article discusses some of the standard techniques for productivity improvement, and how they can be adapted to perform these four functions. Pre-Production The best time to seek high productivity is when a mine is being planned. During pre-production, when most options are still open, an optimum mine design is achievable. At this time, major equipment selections are made, the layout, material handling systems, and processes are designed, and critical energy source decisions are made. By including explicit energy cost projections, decisions can be made that will save significant amounts of money per ton of ore over the life of the mine. Attention can also be given to often overlooked details such as lighting. Some of the same tools used in new mine planning are applicable to productivity improvements at an existing plant. These tools are the charting and modeling methods that have been developed by industrial engineers over the past 75 years. Energy Consumption Before any analysis of energy consumption can be performed, preliminary work is necessary to find the kind of energy used, how much it costs the plant, and when electrical peaks occur. Past bills should be examined to determine the monthly consumption rate and the cost of each energy type. These data should be adjusted to remove effects caused by production fluctuations or weather. Knowing when electrical peak demands occur is necessary because these determine either the electrical capacity needed or the amount that must be bought. At $500-$800 per kW for construction or $5-$15 per kW per month for purchase, they represent a significant cost. By the time these data are collected, planners should be aware of the importance of energy in the total cost of mine operation, and should have the most crucial time data for electrical peak demand. Flow Process Chart Reducing costs can be accomplished by a thorough look at mine systems and how altering one system causes changes in others. By developing and exercising models of production processes outward to the transportation of the final product, otherwise obscured weaknesses may become apparent. There are tools available for analyzing the mine and its associated systems; one of the most useful is the flow process chart. The flow process chart gives a system analysis of a production procedure by classifying all actions into one of five types: operations, inspections, transportation, delays without paperwork, and delays with paperwork. Operation: In an operation, the nature of something is changed. Examples are blasting, washing coal, and processing matter. Denoted by 0. Inspection: Examining an object for identification or to measure some attribute. Examples are determining whether a drill hole is deep enough, deciding how far to cut under an unsupported roof when operating a continuous miner, or checking the lubricant level on a truck. Denoted bye. Transportation: Moving an object from one place to another. Examples are transporting overburden, moving coal on a conveyor belt, and pumping water. Denoted by =>. Delay without paperwork: A delay that is an inherent part of the system. Examples include idle time of a continuous miner while waiting for shuttle cars or for roof bolting, crushed ore in a storage area waiting for grinding and flotation, and people from one craft waiting for another craft to finish. Denoted by D. Delay with paperwork: A delay that can be terminated only by some written authorization. Examples are coal that cannot be removed until authorized by a bill of sale and transportation orders, personnel records, maintenance, or spare parts. Denoted by V. In practice, the flow process chart is completed after data collection and a detailed examination of the process. Data collection is needed to answer questions on distance, quantity, and time for each of the operations. As the analysis is being performed, each step of the process is subjected to these questions: • Why is the step necessary? • What is being moved? • When does the step take place, and why?

Jan 11, 1983

By J. L. Yordan, J. Kortmeyer, I. Yildirim

Talc is used to remove stickies from pulp during paper recycling processes. It is well known that the interaction is controlled by the surface chemistry at the talc/water, sticky/water and talc/sticky interfaces. If the interfacial tensions are known, one can calculate the free energies of interaction and hence predict whether the stickies can be removed by talc. In the present work, the surface tensions of several different talc samples were determined using the acid/base theory. The information was then used to determine appropriate interfacial tensions, which in turn were used to determine the free energy of interaction between talc and stickies. It was found that the calculated free energies are much more negative than those between the stickies and other minerals such as calcium carbonate, bentonite clay and kaolin clays.

Jan 1, 2002

By C. Pieper, J. B. Pateiro Fernandez, S. Möllerherm

"Since the United Nations conference on "environment and development" in Rio de Janeiro in 1992, the term "sustainable development" or short "sustainability" is used more and more in social-political discussions. Agenda 21 calls on the countries on national level as well as governmental and non-governmental organisations on international level to develop a concept of sustainability indicators to measure the progress towards sustainability. This paper deals with the development of an evaluation system for sustainability in the minerals extraction. By their application, aspects of sustainable development in the raw minerals industry are to be systematically conceived and assessed. This project has been carried out on behalf of the German Federal Ministry of Economics and Labour."

Jan 1, 2005

By K. R. Long

Until it was defunded in 1995, the U.S. Bureau of Mines maintained a Cost Estimating System (CES) for prefeasibility-type economic evaluations of mineral deposits and estimating costs at producing and non-producing mines. This system had a significant role in mineral resource assessments to estimate costs of developing and operating known mineral deposits and predicted undiscovered deposits. For legal reasons, the U.S. Geological Survey cannot update and maintain CES. Instead, statistical tools are under development to estimate mining costs from basic properties of mineral deposits such as tonnage, grade, mineralogy, depth, strip ratio, distance from infrastructure, rock strength, and work index. The first step was to re-estimate ?Taylor?s Rule? which relates operating rate to available ore tonnage. The second step was to estimate statistical models of capital and operating costs for open pit porphyry copper mines with flotation concentrators. For a sample of 27 proposed porphyry copper projects, capital costs can be estimated from three variables: mineral processing rate, strip ratio, and distance from nearest railroad before mine construction began. Of all the variables tested, operating costs were found to be significantly correlated only with strip ratio.

Jan 1, 2011

By D. Malhotra

The economic viability of a mining operation depends on continuous process improvements. Diagnostic testing and plant auditing are essential useful tools to improve performance and reduce operating costs. Case studies are discussed to illustrate benefits of these techniques to improve plant efficiency.

Jan 1, 2001

By F. Freme

Coal production in the United States increased in2004 by 36 Mt (39.7 million st) to end the year at 1 Gt(1.11 billion st), according to the U.S. Energy Information Administration (EIA). This was a 3.7-percent in-crease from 2003’s 971.6 Mt (1.07 billion st) (Table 1).(All percentage change calculations are done at the short-tons level.) Although U.S. coal consumption rose in 2004, not all coal-consuming sectors had increased consumption for the year. Coal consumption increased in the electric power sectors by 1 percent and declined slightly in the other industrial sector, while coking coal consumption dropped by 2.4 percent. U.S. coal exports rose for the second consecutive year, while coal imports again increased to record levels. Coal stocks declined during the year, as electric generators used their stockpiles to helpmeet increased demands and missed shipments. Coal producers used their stockpiles to supplement their production levels.

Jan 1, 2005

By Steve Kral

The upswing in prices for base and precious metals, industrial minerals and coal has allowed the global mining industry to ramp up production at existing mines and begin construction of proposed projects. In addition to satisfying shareholders, the industry is also providing good paying jobs and creating needed infra-structure in places that previously did not have either. However, the industry has learned that the prospect of jobs and infrastructure is not necessarily a guarantee that communities will allow mines to be built. The industry must maintain even higher environmental and reclamation standards. And mining companies must help communities plan for life after a mine is closed and the company moves out.

Jan 1, 2005

By P. C. Holloway

La Oroya zinc ferrite (19.5% Zn, 26.6% Fe, 0.052% Ga, 0.075% In) was roasted with coal under conditions more oxidizing than normally used in a Waelz kiln, and the roasted residues were leached with 200 g/L H2SO4. Overall zinc recoveries of up to 97% were achieved, with 35% of the zinc reporting to the fume after roasting at 1,100°C with a bituminous coal addition of 20%. Under these conditions, 93.2% of the Cd, 13.4% of the Cu, 33% of the Ga, 61% of the In and 18.2% of the Pb were recovered either in the fume or in the leach solution. At 2006 metal prices, the value of the recovered metals is comparable to that obtained from commercial Waelz kiln processing of this residue. Zinc in the franklinite (ZnFe2O4) mineral is reduced to zinc vapor, and, after oxidation, some of the zinc is found as ZnO or as Zn2SiO4 in the roasted residue. Iron reacts to form either hematite (Fe2O3) or magnetite (Fe3O4), with no metallic iron detected in the roasted residue, and less than 2% of the iron is solubilized during leaching. The residue produced after roasting and leaching is, therefore, much more stable than the residue from Waelz kiln processing and should be suitable for disposal in a landfill.

Jan 1, 2008

By G. C. Hall, B. E. Hobbs

Giant gold deposits are considered products of crustal-scale systems. Reduced fluids stored in mid to lower crustal reservoirs were discharged into mid to upper crustal sites of deposition. Elements of the architecture include crustal-scale structures, reduced packages of rock and regional seals. Gas-rich aqueous fluids were common but non-aqueous fluids may have been significant in the deeper parts of the systems. Fluid fluxes in over pressured domains were maintained by porosity waves. Abnormal heat input from the mantle may not be required once the systems were perturbed. Fluid-mixing and hypogene enrichment were probably the most significant precipitation processes.

Jan 1, 1999

By J. L. Moreno, A. L. Williamson, R. D. Bartlett

Large open pit mines in desert climates, such as the Phelps Dodge Morenci copper mine in Arizona, can create groundwater cones-of-depression of considerable size and stability. The hydraulic containment provided by the groundwater depression prevents migration of process solutions into the surrounding regional aquifer. Copper leach operations that fall within the groundwater depression may not require costly lining if passive containment can be demonstrated. An approach is presented in this paper that was successfully used to demonstrate passive containment. The approach includes a combination of groundwater modeling and a water balance analysis of leaching operations failing within or immediately near the open pit.

Jan 1, 1999

By Glen Frank, David R. Chapman

Determining the number of boulders and cobbles that will be encountered in the tunnel envelope is one of the most difficult problems confronting the geotechnical engineer in the design of tunnels in glacial terrain. This issue is very important to the contractor, both in determining what methods will be used to construct the facilities and the advance rate that can be achieved for the chosen construction methods. The cost of constructing tunnels by pressurized face tunneling techniques is very sensitive to accurate characterization of the very coarse fraction (large cobble and boulder sized clasts), and no standard method is current available for characterizing boulders and cobbles. Careful use of large diameter borings and the sampling and analytical techniques outlined in this paper can provide a means to answer this difficult question. By performing large diameter borings and carefully recording and sampling the cobbles and boulders encountered, an estimate for the amount of these materials present in the formations sampled can be provided. Using this method allows the designer to communicate the expected geologic conditions to the prospective bidders in a manner that is both definitive and defensible. This paper describes the method as it was used in conjunction with the design of a large diameter sewer tunnel in the Columbus, Ohio area.

Jan 1, 2005

By C. Strachan

This paper presents an evaluation of tailings dam incidents from the 1994 USCOLD Tailings Dam Committee report. Comparisons are also made with water storage dam incidents from USCOLD reports and recent tailings dam incidents. The evaluation results show that tailings dam incidents are due to a number of factors including overtopping, static and seismic instability, seepage and internal erosion, and foundation conditions, and that no particular type of tailings dam or operational condition is more susceptible to incidents. In addition, the results confirm that tailings dams should be located, designed, operated, and reclaimed with a thorough knowledge of site conditions, mill operation, site monitoring, and tailings characteristics.

Jan 1, 1999

By A. K. Majumder

Particle motion in fluids is a subject of considerable practical importance to engineers working in fields such as hydraulics, river mechanics, chemical engineering and mineral processing. Many mathematical models have been proposed to predict the terminal settling velocities of particles in a fluid medium. The selection of an appropriate mathematical model has, therefore, become a challenging task for practicing engineers. This paper reports on an attempt to identify some of the useful models found in the literature for predicting particle-settling velocities in a fluid under free- and hindered-settling conditions. From this study, it was concluded that there is no well-accepted model validated by experimental data available for predicting particle hindered-settling velocities in a suspension of polydisperse and polydens particles. Collective efforts should, therefore, be made towards developing a hindered-settling model, as this is an absolute prerequisite for many model structures in mineral processing and other engineering disciplines.

Jan 1, 2007

Cripple Creek and Victor Gold Mine is an epithermal gold deposit located in the Rocky Mountains of Colorado. Surface operations are continuing along with an expansion for an onsite mill to take place in the next couple of years. The surface pit is currently progressing downward from an oxidized zone into a transitional, more sulfide/ telluride-rich zone. Gold mineralization includes native gold, electrum, and tellurides. Cyanide heap leaching is the recovery process for the oxidized ore with the sulfide/telluride-rich ore to be processed at the new onsite mill. Ore characterization prior to mining is vital when there are two possible recovery processes. This characterization is dependent on geometallurgy. To identify the causes of the variability, multiple parameters are analyzed and assayed. These parameters are measured by a variety of analytical testwork. The analytical testwork provides measurements for the desired parameters. Geometallurgical models are developed for the parameters per recovery process, so estimations can be inserted into the resource model to optimize operations and recoveries.

Feb 27, 2013

By J. G. Davis

The St. Peter Sandstone is typically a well-sorted, friable, ultra-pure, fine- to medium-grained, quartzose sandstone with silica content higher than 99 weight percent in places. The sand grains are well-rounded, highly spherical and characteristically frosted. Their size typically varies from 2 millimeters diameter (No. 10 U.S. Standard Sieve Series size) to less than 0.08 millimeters diameter (No. 200 U.S. Standard Sieve Series size). A freshly exposed surface of the formation is commonly white with shades of pink and green. Weathered surfaces are a dirty gray or brown and are case-hardened at many localities. Bedding is characteristically indistinct, and the formation usually appears massive throughout. The rock is cross-bedded and ripple-marked locally. The formation is generally porous, permeable and rarely fossiliferous in Missouri. The St. Peter is continuously present in the subsurface in the northern half of the state and along the southeastern edge of the state. The St. Peter crops out in a narrow band that starts in western Montgomery County and runs southeastward, along the Missouri River, to just west of St. Louis and continues south, just west of the Mississippi River, through Scott County. The outcrop belt varies from less than one mile wide to over ten miles wide, and it is over 150 miles in length. The formation dips into the subsurface radially away from the outcrop band. A notable isolated outcrop occurs in Lincoln County to the north of the main outcrop band. The St. Peter is discontinuously present in the subsurface along a band in the west-central portion of the state. It is not present at the surface or in subsurface in the remainder of the state. The formation averages 80?100 feet thick. There is an estimated 3.8 trillion short tons of St. Peter in Missouri. Sieve analyses on drill cuttings indicate three subsurface locations in northeastern Missouri where the St. Peter is greater than 10 percent by weight of sand falling in the 20?40 U.S. Standard Sieve Series size range. The St. Peter was first produced in Missouri in the 1870s for the manufacture of glass. Since that time it has been used as a paint additive, filler material, polishing compound, filtering media, and recently it is commonly used as a fracture proppant in oil and gas wells. The St. Peter is currently quarried and produced in Missouri from four sites located in St. Louis, Jefferson and Perry counties. In the same area there are at least nine abandoned historic mine sites.

Feb 27, 2013

By R. Hipsley, D. Arbonies, P. J. Dobak, M. Visher

The Storm deposit is a high grade breccia hosted “Carlin-type” gold deposit located at the north end of the Carlin Trend. Storm consists of 3 smaller deposits: 1) 49er Zone, 2) End Zone, 3) Discovery Zone. Structural intersections and favorable stratigraphy at the Paleozoic Popovich/Rodeo Creek formation and Bootstrap limestone formation contact are the primary known controls to gold mineralization at Storm. High grade silica-sulfide breccia occurs in the footwall of the north-south trending, dike filled, Dee fault. This mineralization cross-cuts silicified heterolithic breccia zones localized above the Bootstrap limestone where northwest, dike filled, reverse faults cut this structural-stratigraphic horizon. 40Ar/39Ar dates of 37.57+ 0.34 Ma (basalt dike) and 162 Ma (lamprophyre dike) have been obtained from dikes in the Dee pit which are locally mineralized by the same event as Storm. This paper will focus on the descriptive aspects of the Storm deposits.

Jan 1, 2001

By Y. Breau, F. Robichaud

The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.

Jan 1, 2002

By J. L. Cupp, R. C. Ford, B. R. Romig

The Climax Molybdenum Mine, located near Leadville, Colorado, is the site of a lengthy mining history spanning more than 80 years. In the 1960’s, extraction of molybdenum from oxide ore located adjacent to the massive molybdenite sulfide deposit resulted in the construction of an earthen core dam to impound fine-grained oxide tailing in the Eagle River Valley. Through recognized value of water storage and reclamation opportunities, a tailing removal project was initiated in 1993 to convert the impoundment facilities to a post-mining beneficial land use of developed water resources. An evaluation of the effect residual materials and lake dynamics would have on in-stream water quality was performed. Eagle Park Reservoir stands as a model for future reclamation efforts that involve water delivery to highly sensitive receiving waters. This paper provides a case study on project development, the evolution of water quality assessment, and the regulatory framework that contributed to this project’s success.

Jan 1, 1999

By S. C. Sun

Pennsylvania has ample reserves of high-alumina clays which are potential sources of alumina, but many of these clays contain large amounts of iron, which makes them unsuitable for treatment by acid processes(1). The purpose of this investigation was to determine the optimum conditions for the selective hydrochloric acid leaching of iron (2-4) prior to the sulfuric acid extraction of alumina from Pennsylvania ferruginous high-alumina clays. This was accomplished by first testing the iron-bearing minerals and the clay minerals most often encountered in Pennsylvania clays to determine their rate of dissolution in hydrochloric acid solutions. The results of individual minerals were then based for leaching Pennsylvania clays with a 19% hydrochloric acid solution at the boiling point of the acid for approximately 30 minutes to achieve as high as 90% iron removal and only 2-5% alumina losses.

Jan 1, 1968

By R. M. G. Machunter

Computer models of metallurgical circuits are extensively utilised in design, and prediction of overall plant separation performance. As always, in the final optimised flowsheet design there is a compromise between the recovery of values and grade of the circuit output. This paper mathematically examines various circuit options for the generation of a heavy mineral concentrate from a generic mineral sands wet concentrator plant. Based on data derived from testwork, any particular mineral sand has a unique release curve describing the separation performance of the heavy mineral suite. Models are constructed that combine particular stage output streams as feed to other stages in various configurations. The ramifications of each option are discussed and reasons why one particular option is selected over the others examined.

Jan 1, 2005