Search Documents

By Hiroshi Yamazaki

The paper describes prediction, control and validation of face pressures, and special TBM features for the bored tunnels of the New Metro Rail City Project, Perth, Australia. The selected EPB-TBM passed below a heritage bridge and the operational Perth Railway station in ground conditions consisting of fully saturated uniform sand combined with shallow overburden and a horizontal alignment radius of only 135m. Therefore, strict control of volume loss, TBM operations and ground movements was vital requiring continuous evaluation and adjustments to TBM operation parameters. The paper discusses the effectiveness of applied TBM face pressures and the used foam/polymer soil conditioning which was measured against achieved volume loss and the predicted range of ground settlements.

By R. M. Imhof, M. J. G. Battersby, G. Ciernioch

Pneumatic flotation is rapidly becoming accepted in the main stream of flotation techniques. Imhoflot is a pneumatic flotation process that in recent years has undergone progressive development. It combines short flotation times with excellent selectivity by employing intense pre-aeration and dispersion. K+S GmbH (K+S), Germany, has installed a complete Imhoflot flotation plant at its Sigmundshall plant. The plant treats hard salt consisting of sylvine, halite, anhydrite and kieserite. The reason for selection was that Imhoflot achieves the required grades of plus 60 weight percent K2O whilst offering lower operating costs than conventional flotation installations.

Jan 1, 2002

By Douglas B. Silver

Super Cycle future The final topic is mining?s future. The most important questions are ?How much longer is the Super Cycle going to last? What should we expect to see going forward? How will the Super Cycle end?? Three possible scenarios follow. Scenario one: Super Cycle has peaked Kathy Casey-Kirschling is officially the first Baby Boomer. She was born Jan. 1st, 1946. If you google ?first baby boomer,? she?s the one that shows up. A Baby Boomer is anybody born between 1946 and 1964. In the United States, it represents about a quarter of the population ? approximately 76 million people. The Baby Boomer generation is going to change the economics of the world because there are so many in the generation. A review of spending patterns indicates that the largest amount of discretionary spending occurs between the ages of 49 and 52. Retired people tend to live on fixed incomes so they have less discretionary income. They also tend to downsize their house, which may contribute to the housing glut and the need for a lot less metal. Therefore, the upcoming retirement of the Baby Boomer generation could result in a massive shift in economic spending resulting in the peaking of the Super Cycle. Figure 1 is an index graph from the Toronto Stock Exchange (TSX). The index has recently peaked. A lot of people see that as a sign that bad things coming our way. A careful review of different commodity prices also suggest that the peak has occurred and it does not seem to matter which commodity prices are considered. Copper prices have seen a peak as have nickel prices. Nickel and molybdenum displayed the same trend with a peak in 2005 as did zinc. Uranium, which has single-handedly tried to behave like the dot com craze, has also peaked.

Jan 1, 2008

By Daniel N. Adams

The University Link project extends Seattle?s light rail from downtown to University of Washington (UW). It includes 5.0 kilometers (3.15 miles) of twin-bored, 6.4 meters (21 feet) excavated diameter tunnels, and two cut-and-cover stations. The Capitol Hill Station (CHS) requires an excavation 170.7 meters (560 feet) long, 22.6 meters (74 feet) wide, and 22.9 meters (75 feet) deep. The University of Washington Station (UWS) requires an excavation of about 238.4 meters (782 feet) long, 21.3 meters (70 feet) wide, and 33.5 meters (110 feet) deep. The project is within the glacially diverse soils of the Puget Sound region, below groundwater. This paper highlights major station and tunnel design elements, including the approach to support of excavation at both station boxes, and the site staging requirements.

Jan 1, 2008

By Steve Dubnewych

The Joint Water Pollution Control Plant, operated by the Sanitation Districts of Los Angeles County, treats wastewater generated by over three million people. A new tunnel and ocean outfall is being considered to meet future hydraulic demands and provide long-term redundancy for the Districts? existing tunnels, portions of which were constructed as early as the 1930s. The detailed process used to evaluate the feasibility of various tunnel and out-fall locations is described. Challenges include a geologic profile with mixed face and squeezing ground conditions; high water pressures; active fault crossings; gassy and contaminated ground conditions; and liquefaction, slope stability, and lateral spreading concerns in the area of the riser and diffusers.

By Russell Miller, Fun-Den Wang

High Pressure Water Jet Assisted Tunneling The high pressure water jet assisted tunneling project was conducted in a granite quarry near Skykomish, Washington, approximately 90 miles east of Seattle. A 7-ft diam tunnel boring machine was modified and equipped with high pressure water jets. The concept that tunneling rates can be improved by using high pressure water jets was validated, with an average increased advance rate of 50% to 60%. For some tests, the advance rate was more than doubled. A comprehensive economic analysis has shown that very significant savings are possible. At a 50% increase in advance rate, cost savings of 14% and 24% were projected for 10-ft and 20-ft diam tunnels respectively. These benefits were seen to be relatively insensitive to water jet equipment costs.

Jan 1, 1976

By I. Nimmo

Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. Communications issues were resolved, better coordination of materials, improved situation awareness during startups, abnormal operations and an opportunity to make improvements during normal operations characterize the changes at the Worsley Refinery. This presentation will review the reasons for the change. Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. This presentation will review the reasons for the change, what changed and the process of changing the culture from reactive to predictive and what difference that has made.

Jan 1, 2011

By R. L. Wolfrom, R. Hogg, S. Chander

A gravimetric method for measuring rates of capillary rise in powders was explored. Methods to improve reproducibility and consistency of the results were investigated. In particular, the effects of particle size and packing uniformity were addressed. Studies of the wetting behavior of both spherical glass beads and irregularly shaped synthetic graphite particles by various organic liquids were carried out. Standardized procedures for bed preparation are described. The applicability of the Washburn equation for surface energy evaluation in such systems is discussed.

Jan 1, 2002

By R. J. R. Cornelissen

The elimination of the incidence of silicosis in employees in industries such as mining and pottery is an ongoing international initiative. After many decades of industrial activity in these industries and many dollars spent on preventative measures, silicosis is still occurring. The exposure-prevention measures taken so far have certainly improved the working environment dust concentrations; however, the illness is still regularly diagnosed in workers. More funding is needed for interventions to improve working conditions. Many aspects of dust prevention and suppression will be researched and exposure assessment methodologies and equipment will need to be reviewed for the purposes of improvements in effectiveness. This paper presents results from laboratory tests carried out on gravimetric sampling pumps and cyclones. It highlights the erratic flow produced by gravimetric pumps of three different manufacturers who claim their respective pumps are equipped with flow stabilisers. The standard BS EN 1232:1997 is used as a basis for the tests. A method, albeit impractical for fieldwork, is shown for the elimination of the pulsation in the flow. This method serves to prove the method and protocol used in this study. The pressure loss caused air-flow resistance of cyclones is measured. The air inlet aperture size of cyclones is measured. The large discrepancy in the two criteria between individual cyclones is shown. The paper concludes that all the pumps tested failed the prescribed limits of BS EN 1232:1997 regarding the pulsation of the gravimetric sampling flow. The difference in flow characteristics of the cyclones, together with the erratic flow produced by the pumps, throws into question the accuracy of the exposure assessments. It is suggested that substantial resources be channelled towards solving these flow problems in parallel with measures taken to reduce exposure. In principle, the accurate assessment of exposure and dust concentration levels is a prerequisite for effective management of the problem of silicosis.

Jan 1, 2009

By Larry R. Powell

The Bureau of Mines, in cooperation with the Illinois Mine Subsidence Insurance Fund, is monitoring the response of two foundations to ground movements induced by subsidence from high extraction mining in southern Illinois. The objectives of the monitoring program are to study the inter- action between the ground surface and a foundation during a subsidence event and to determine the capability of the tiltmeter to detect and monitor subsidence movements. Tiltmeter data were obtained on two foundations constructed near Sesser, IL. One of the 30-by 40- ft foundations was constructed with a typical poured concrete footing, the other with a rein- forced-concrete footing poured on top of pol yethylene sheeting placed over a compacted layer of sand. Soil-filled bins were placed on the perimeters of both foundations to simulate superstructure loads. Monitoring pins and tiltplates were installed on the corners and midpoints of the footing. Additional survey points were established on the five-acre site to track the mining advance. This paper describes the monitoring instrumentation and techniques as they relate to the mining and site conditions. The capability of a tilt- meter to detect and follow the tilt of the foundations is demonstrated.

Jan 1, 1986

In this study, the flotation performances of ethoxycarbonyl thionocarbamate (ECTC), dialkyl thionocarbamate (DATC) and xanthate copper sulfide collectors are compared by the structure-reactivity relationship using generalized perturbation theory and density functional calculation at the B3PW91/6-31G(D) level. The electron-donating power of xanthates is strong and, therefore, xanthates can strongly react with metal cation on the surfaces of copper and iron sulfide minerals through the formation of normal covalent bonds. This explains the poor selectivity of xanthates and also the high pH levels (above 13) required for the flotation separation of copper/iron sulfide minerals. DATCs are more selective for copper sulfide flotation, particularly against gangue iron sulfides. Although less powerful than xanthates, DATCs can perform copper/iron flotation separation at lower operating pH (commonly at pH levels below 11.5). ECTCs use an ethoxycarbonyl replacing an alkyl N-substituent in DATCs. The presence of the ethoxycarbonyl group effectively changes the functional group of collector from -C(=S)NH- to -C(=S)NHC(=O)-. The strong electron-withdrawing ethoxycarbonyl group adjacent to the C=S group decreases the electron density of the sulfur atom, which improves ECTC?s selectivity against iron sulfide minerals at slightly alkaline conditions. The lowest unoccupied molecular orbit (LUMO) of ECTC, which is constituted by the pz-orbit of every atoms in the conjugate -O-C(=O)-N-C(=S)-O- group and which is pleased with accepting richly d-orbital electrons (feedback electrons) from the (t2g)6(eg)3Cu(II) or t6e4Cu(I) configuration of copper cation on the surfaces of copper sulfide minerals, resulted in the formation of dative p-bond. The iron atom, which has a (t2g)6Fe(II) or (t2ga)3(ega)2 Fe(III) configuration on the surfaces of iron sulfide minerals (Fe(III) is the predominant composition at alkaline conditions), has difficulty in offering its d-orbital electrons (feedback electrons) to ECTC?s LUMO. ECTC collectors are powerful for copper sulfide minerals and very selective against iron sulfides, which has been further confirmed by UV spectra and bench-scale and industrial-scale flotation tests.

Jan 1, 2008

By Steve Kral

President Bush’s National Energy Program and his Clear Skies Initiative both emphasize the use of coal to help meet the nation’s growing energy needs. And why not? Coal is currently responsible for more than 50 percent of the nation’s electricity generation. That fact, though, seems to be lost on policy makers, the environmental community and the public. Critics of coal advocate the increased use of renewable energy sources and the increased use of natural gas. Renewables, though, are only capable of generating a tiny fraction of the power required. Natural gas is expensive. And natural gas production cannot keep up with demand, especially given the nation’s increasing energy needs.

Jan 1, 2003

By L. B. Hales

Image analysis for feed belts and flotation has been used for over 20 years. It has been shown to aid in the modelling and optimization of Sag Mill circuits, and any improvements in the image analysis result in improvements in the model for control. Using a laser to measure the height-profile of rocks on the conveyor has been shown to increase the accuracy of the size classification. We have developed a system using two cameras in a stereoscopic configuration to provide height-profile measurement without the added expense and safety concerns of using a laser. Additionally, we have developed a novel technique for calibration of the system, using artificial intelligence techniques to optimize the model fit by adjusting the image analysis tuning parameters to values resulting in the best classification.

Feb 27, 2013

By E. C. Robertson

D.G. Wilder I found the suggestion that the amount of displacement of a fault can be numerically related to the thickness of gouge or breccia to be both intuitively satisfying and intriguing. I have long agreed that there is some type of relationship between the amount of gouge and the amount of displacement of faults. I congratulate the author for developing a numerical relationship between them. However, I am concerned that the limits for applying this relationship be fully understood. An underlying assumption in this approach is that there is either a uniform thickness of gouge or breccia along a given fault or the thickness does not vary widely. Since it is not always possible to confirm this, the displacements derived by this method should be viewed with caution unless significant fault extent can be observed. At the Nevada Test Site, in drifts constructed in granite for test emplacement of spent nuclear reactor fuel, we found a fault with 0.3 to 0.4 m (12 to 16 in.) of clay gouge. Within a few meters of this location, the fault had no clay gouge, but rather consisted of a highly fractured zone with significantly altered rock and some slickensides. Based on Fig. 1, the 0.3 to 0.4 m (12 to 16 in.) thickness of gouge would indicate a displacement in excess of 30 m (98 ft). However, no gouge thickness would indicate essentially no displacement. Based on a quartz vein that terminated on the fault, and is not identified nearby, an estimated displacement of more than a few meters was made. This estimate is consistent with that obtained using the regression line proposed in the paper if the 0.3 to 0.4 m (12 to 16 in.) thickness for the gouge is used. However, using the regression curves with zero thickness would not yield results consistent with what was observed in the field. Therefore, it is important to recognize that the suggested procedure would properly yield a range of probable displacements. ? *Work performed under the auspices of the US Department of Energy by the Lawrence Livermore National Laboratory under Contract W-7405-Eng-48. Reply by E.C. Robertson It is certainly true that the t (thickness) of gg-bx (gouge and breccia) on a fault does vary along the fault. My observations have been that near the termination of a fault, the displacement d is small and the t is also small, whereas the maximum d and t will usually be found in the central part of the fault. The information on gg-bx and t of the fault found in granite in the NTS tunnel by Mr. Wilder could be interpreted somewhat differently than he does. He speaks of the fault changing within a few meters from 0.3 to 0.4 m (12 to 16 in.) of clay gg to "a highly fractured zone with significantly altered rock and some slickensides," but no gg. The highly fractured rock may be taken to be bx, rock not so finely ground as gg but still crushed by the fault movement, equivalent to the gg in my usage, and probably occupying about the same t. Mr. Wilder's estimates for the fault in the NTS tunnel for t of 0.3 to 0.4 m (12 to 16 in.) and for d of a quartz vein, in excess of "a few meters," would place the point on the low side of the central trend line in my Fig. 1, at the lower limit. There is, of course, a problem with determining d using displacement of only one planar surface. It would be greater or lesser depending on the rake of the movement. Finally, estimating the d of a fault from its t should be made with awareness of our present uncertainties, as pointed out by Mr. Wilder. Although the central trend line in my Fig. 1 has a ratio of d/t of 100, I have put the limiting ratios at 10 and 1000. Understanding of the values of the ratio will be improved only with collection of more data, for which the discussion of Mr. Wilder is much appreciated. G.C. Waterman E.C. Robertson's paper provides significant information to a geologist attempting to deduce fault offset by noting the products of structural dislocation. However, considerable mapping in underground and open-pit mines, and examination of structures produced in different geological settings, have convinced me that gouge and breccia thickness are controlled by geological conditions and fault movement. The following paragraphs suggest geological variables that control them. 1. Depth of Loading A near-surface fault resulting from tensional stress has more breccia/gouge than is produced by a similar stress at considerable depth. A deep-loaded compressional stress may produce a linear zone of schist, or structural dislocation may occur along an earlier formed belt of schist. Such "shear zones" are common in Canadian mines in precambrian rocks. In neither case can offset be directly deduced by an analysis of the minimal gouge/breccia in the shistose rocks. At greater depth, stress may be partially to wholly relieved by flowage. I vividly recall first noting the regional "Midas Thrust" in the Lark mine, Bingham Mining District, UT (where we called the structure the North Fault). My recorded notes, as I remember them, showed a narrow gouge streak separated the `Jordan" and "Commercial" limestone units from impure, muddy limestone beds of uncertain stratigraphic position. The visible structure did not indicate the great importance of this premineral fault

Jan 12, 1984

The technical parametrization of reserves is a technique which has made an important contribution to the definition and the calculation of optimal mining projects. Its applications to a new open-pit optimization program have already been presented in various papers (François-Bongarçon and Maréchal (1976); François-Bongarçon and Guibal (1981)). The present paper gives a brief description of the general problem of parametrizing reserves before going into the details of the practical algorithms used in two typical cases, i.e. open-pit mining and mining between hanging wall and foot wall.

Jan 1, 1982

By John E. Newby

The Brightwater Conveyance System consists of four tunnel segments in three tunnel con-tracts, comprising over 21,760 m (71,400 ft) of pressurized face tunneling in complex glacial and non-glacial soft ground conditions with a large proportion 60 m (197 ft) or more below the ground surface with up to 7 bars groundwater head. This resulted in unique technical challenges for establishing geotechnical baseline values. The process used to develop these baseline values and specifications with regard to the level of risk that the owner, King County, was willing to accept is described in this paper.

Jan 1, 2008

The fundamental objective of mine plans are usually to maximize the mine profit by extracting ore at the lowest possible cost over the mine life while some technical constraints are satisfied. Since the costs associated with the operation of trucks and shovels as resources are significant, determining the optimum number and allocation of these resources is an essential issue. This paper presents a Mixed Integer Linear Programming (MILP) model to determine the optimum number of shovels and trucks required to meet the short-term plan?s goals. Also, the model takes into account the allocation of trucks and shovels to mining faces. This model minimizes operational costs, while attempting to meet the production demand and to satisfy technological constraints. This paper also analyzes the operations of trucks and shovels in an open pit mine using ARENA simulation software.

Jan 1, 2012

Once every three years the eyes of the construction and mining industry?s turn to Munich, Germany for the bauma trade fair and exhibition. From April 19-25, Messe München International (MMI) will host the 29th edition of this massive show that, despite the recent recession and global financial struggles, has grown yet again. The show, which is completely booked, will take place on a record 555,000 m2 (5.9 million sq ft) of indoor and outdoor exhibition space at the New Munich Trade Fair Centre. More than 3,000 exhibitors are expected to make use of this event. To prepare for the show that highlights some of the largest and most impressive construction and mining equipment in the world, Messe München began working months in advance on getting the infrastructure on the open-air site ready, in time for the arrival of the gigantic machinery exhibits, which started to arrive in March. Part of the preparations include a new entrance at the northwest corner of the exhibition center that was built to regulate visitor flow better. This should help with bauma considering that in 2007 more than 500,000 visitors passed through the gates. ?Although in 2010 the construction machinery sector in many markets worldwide will be recovering only slowly from the recession, we are pleased to report that we are seeing strong demand for exhibition space. This shows that exhibitors regard participation in the world?s leading trade fair bauma as a must, although many are at present having to make cuts in their advertising and trade-fair budgets. We have been particularly surprised by the strong demand for space from exhibitors from markets like China, India and Turkey. The fair is fully booked and many more companies are on the waiting list,? said Eugen Egetenmeir, managing director of Messe München. More than 50 percent of the exhibitors at bauma 2010 come from countries outside of Germany. While the show?s primary focus is on the construction section, it is not as if the mining sector will be difficult to find. With some of the largest equipment in world on display in section C2 (Fig. 1), the mining industry is sure to be well-represented.

Jan 4, 2010

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimeter precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many metalliferous and coal mines throughout the world. Over 80 systems are currently being used with current operations in 17 countries. Greater than 200 rock slope collapses and waste dump failures (from several to millions of tones) have been monitored, with ?warning? precursor movements recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines. Slope Stability Hazards and Rock Slope Monitoring in Open Pit Mines Surface mining often creates excavation boundaries which are steeper than those would be created under natural processes in the same rock type. They are also undertake quite rapid stress changes during mining and are influenced by significant external forces such as blast vibrations and changes in groundwater. These conditions are likely to allow some degree of instability to develop in the pit slopes. The hazards associated with this instability of pit slopes can be extremely variable in character; ranging from small cobble sized rocks dislodging and falling from mine benches to complete collapse of entire pit walls. It is usually the position of mine geotechnical or geological staff to assess these hazards for mine operations. The assessment of hazards due to unstable slopes can be done by visual observation of precursor signs such as fracturing or rilling of loose material. A more reliable indicator of instability involves the quantitative measurement of outward movement and acceleration of material as an instability mechanism develops. There is strong evidence that small precursor movements of a rock wall occur for an extended period prior to rock slope collapse (Hoek and Bray, 1981). Development of a monitoring system, adopting acceptable slope deformation criteria coupled with warning systems and design of stabilization or risk reduction measures if appropriate has become a standard method of dealing with slope instability. Framework for Slope Hazard Management using the SSR A framework for the management of slope hazards is shown in Figure 1 (discussed in detail in Harries, 2007). Although this framework is specifically for use with the Slope Stability Radar, a similar framework could be developed for other monitoring technologies for monitoring slope deformation. An important point to consider is the sequential nature of the hazard management framework from selecting the context ? identifying hazards ? analysing hazards ? evaluating hazards ? treating hazards. [ ] Once the context of the system has been developed (for example ? to monitor for rapid bench scale collapse), the identification of hazards is the next stage in hazard management. Identification of slope hazards can be relatively straightforward due to the visual nature of the information that the SSR system produces. The areas of excessive wall deformation are highlighted in color maps of the mine slope with a co-aligned photographic image to review the actual site of interest. The responsible personnel must then analyses this data, usually reviewing the deformation style and rate, as well as the size of area that appears to be failing. This information can then be evaluated against organisation protocols (for example it may be only a small sub-bench failure that will be ?caught? by existing benches and hence can be categorized as a lower risk). Once these hazards are evaluated they can then be treated if required. Two major options are available to reduce the risk during this treatment option. We can reduce the likelihood of failure ? for example by buttressing the failure or de-pressurising of water pressures in a slope. However, the most likely plan of action is to reduce the consequence of the failure. One of the most successful opportunities to reduce the consequence of a slope failure is to ensure that no personnel or mining equipment is present at the location of a slope failure when collapse finally occurs. This has been the major benefit of the SSR system to the different mining operations around the world. SLOPE STABILITY RADAR TECHNOLOGY OUTLINE Slope Stability Radar system specifications and capabilities: ? Measurement precision +/- 0.1mm (std.) ? Perforated dish and other features enable it to operate in high wind conditions ? Measurement range is 1700 metres ? Scans 270 degrees horizontally and 120 degrees vertically ? 1 ? 30 minute repeat rate for area scans (varies according to area being scanned ? RF exposure (<0.05mW/cm2) is a factor of 200 below the acceptable limit for the general population (1 mW/cm2) ? Tolerant to vibration and mining equipment ? The system weighs approximately 1500 Kg ? Remote area power supply enabling unmanned, continuous 24/7 monitoring ? Real time monitoring

Jan 1, 2009

By Paul D. Tomlingson

Modern production equipment has been designed with greater productive capacity and higher reliability to meet the rigorous operating demands of the mining industry. These improvements have also made the equipment more complex and challenging to maintain. Whether these equipment enhancements contribute to more effective mining operations depends on the overall quality of maintenance. Maintenance is not a stand-alone activity. Although its quality depends primarily on maintenance, cooperation and support from other departments, coupled with the skillful guidance of mining managers, greatly influence maintenance success. Therefore, maintenance risk management must look beyond maintenance itself. Successful maintenance risk management begins with an assessment of the maintenance-related interactions of all mining departments within the mine’s stated operating strategy.

Jan 1, 2005