Search Documents

By R. J. Davidson, M. V. Nkosi, V. Veronsee

When activated carbon is used for the recovery of gold and silver from Witwatersrand gold-plant solutions, severe fouling of the carbon by calcium carbonate is experienced. Also, difficulty is encountered in the retention of the adsorbed silver on the carbon because it is displaced by gold. The acidification of plant pregnant solutions before they are contacted with carbon was therefore investigated as a means of overcoming these shortcomings. The results from batch laboratory experiments on the effect of pH on gold adsorption from plant solutions and from synthetic solutions of high ionic strength indicated reaction rate optima in the region of pH 5 and below pH I. The effect of pH on the equilibrium capacity constant for gold adsorption onto activated carbon was also studied, using both a plant solution and a synthetic solution of high ionic strength. In the case of the plant solution, the results suggested only a marginal change in carbon capacity for gold in the pH range 12 to 6, with significant increases in capacity at lower pH values. In the case of the synthetic solution of high ionic strength, the capacity constant was found to increase steadily as the pH was lowered from 12 to I. It was also found that the gold adsorption capacity of the carbon was significantly better for the synthetic solution. No precipitation of gold from the pregnant solution (gold content approximately 6 g/t) was noted as the pH was decreased to values as low as ,. However, about 25 per cent of the 0,6 g/t silver content was found to have precipitated when a pH value of 3,0 was attained. Further substantial precipitation of silver took place as the pH was lowered further. The investigation was extended by the passing of suitably acidified gold-plant solutions through one or more columns containing activated carbon. Preliminary results showed that the particle size of the carbon had a significant effect on the rate of gold adsorption. No displacement of adsorbed silver by gold was observed to take place at an influent pH of 5. In a typical continuous 'merry-go-round' operation involving three columns in which gold was eluted from the lead column every 48 hours, effluent values averaging 0,001 g/t gold could be consistently achieved under simulated plant-operating conditions. The results were obtained at relatively high velocities of influent solution, resulting in very little hold-up of gold in the carbon-recovery circuit. More than 99,9 per cent of the gold and more than 99,8 per cent of the silver was recovered in the adsorption circuit, while the elution data indicated an average elution recovery of 99,8 per cent of the adsorbed gold and 98,2 per cent of the adsorbed silver. Elution of the carbon was carried out at 91 QC. This involved pretreatment of the carbon with a sodium cyanide solution, followed by elution with deionized water. At a loading flowrate of 66 bed volumes per hour, the indicated take-up of metals on the carbon in the lead column was as follows; 53 k g/t gold, 6 k g/t silver, 57 k g/t copper, 14 k g/t nickel, and I k g/t zinc. Only a trace of cobalt was adsorbed. At an elution rate of 1,7 bed volumes per hour, the lead column was found to be completely stripped in under 5 hours, with concentrations of gold in the eluate reaching 6 to 7 g/l. Besides the excellent adsorption and elution results obtained when acidified pregnant solution was used, no fouling of the carbon was indicated, and the pressure drop across the three columns was considered to be well within practical limits. When compared with conventional zinc precipitation, the carbon process would appear to have considerable economic merit, with strong indications that significant savings would be possible both in capital and operating costs. Further pilot-plant experiments, preferably on a gold plant, would be required before a meaningful cost comparison could be made with the existing process.

Jan 1, 1979

By B. J. Pieters

The paper describes the difficulties experienced with inferior coking coals as Iscor began using larger blast furnaces for the production of liquid iron. Research conducted at Iscor from 1977 to 1979 showed that benefits could be gained from the use of partially briqueted charges, and it was decided to install briqueting plants at the Vanderbijlpark and Newcastle Works. Details are given of the later plant, which was supplied by a consortium consisting of Voest Alpine, Didier Engineering, and Sumitomo Metal Industries. Sumitomo also supplied information on the optimization of coke quality along the lines of their Sumicoal System. The results have been a marked improvement in coke quality, much better blast-furnace operation, and increased productivity.

Jan 1, 1991

By J. M. Stewart

Although the incidence of heat stroke in South African gold mines is small, work continues on its reduction. This paper proposes limits of heat stress that are applicable to South African underground conditions, with the warning that they should not be extrapolated to other situations without careful consideration having first been given to their limitations. These limits of heat stress take physical and physiological considerations into account, and they correspond to there being a 10-6 risk of an essentially nude man developing a rectal temperature in excess of 40°C. It is recommended that further work should be undertaken on the development of equations for the calculation of the heat transfer from clothed men, the derivation of equations that quantify the physiological conductance and sweat rate response of humans, and on establishing the frequency distributions that describe variations in rectal temperature response between individuals in different types of environment.

Jan 1, 1981

By M. J. Nicol

This paper ,examines the kinetics of the extraction of uranium from acid sulphate solutions by strongbase anionexchange resins. Parameters such as the concentration of uranium in solution. the agitation of the resin beads in solution. the size of the resin beads. and the degree of cross-linking within the resin matrix were varied. and the effec ts on the kinetics are reported. The applicability, of various empirical kinetic models to the description of the data is assessed, and an attempt is made at the modelling of the rate data in terms of established theories about the diffusion of ions through films of stagnant liquid and through spherical beads of resin.

Jan 1, 1980

By Y. Suzuki, H. Yoshida, K. Sakaguchi, K. Matsuki, M. Minami

To estimate three dimensional in-situ stress at great depth, Downward Compact Conical-ended Borehole Overcoring (DCCBO) technique, which is one of stress relief methods, was developed. DCCBO technique can be applied to a water-filled vertical/sub-vertical borehole. In in-situ tests, the bonding device and the cleaning system were verified to work well in a water-filled borehole with cuttings on the bottom. Um dreidimensionale in-situ Beanspruchungen in großen Tiefen abzuschätzen, wurde das Downward Compact Conical-ended Borhole Overcoring (DCCBO) Verfahren entwickelt, wobei es sich um ein diese Beanspruchungen entlastendes Verfahren handelt. Die DCCBO Technik kann auf wassergefüllte vertikale und subvertikale Bohrlöcher angewandt werden. Bei den in-situ Tests wurde die Einsatzfähigkeit der Verbindungsvorrichtung und des Reinigungssystems für wassergefüllte Bohrlöcher mit Einschnitten am Boden bestätigt. La technique de Downward Compact Conical-ended Borehole Overcoring (DCCBO) ou ‘Surcarottage par sondage à extrémité conique compact dirigé vers le bas’, qui est une méthode de détente des tensions, a été développée pour calculer les tensions in-situ à trois dimensions à grande profondeur. Cette technique peut s’appliquer à des sondages verticaux/sub-verticaux remplis d’eau. Au cours des essais in-situ il a pu être vérifié que le dispositif de liaison et le système de nettoyage fonctionnaient bien dans un trou de forage rempli d’eau avec saignées au fond.

Jan 1, 2003

By Anders Erlandsson

"The crude ores from the LKAB mines are sorted and refined into a number of products. As there are a number of different plants the flow of material is often complex.in connection with studies of a proposed extensive investment program it was necessary to get a good measure of the changes which would be caused in the total profit by the different possible investments. A linear programming model was set up to accomplish this, and to cover the consequential effects on the production system. The objective function of the model maximized the total profit, taking into account restrictions in materials balances, blending conditions, production capacities and market. The changes in total profit resulting from the different investment alternatives, together with investment and fixed costs, were used in a series of investment analyses. The application has proved to be very successful and the results come very near to what was expected."

Jan 1, 2014

By R. I. Klintworth

The multi-reef area of Cooke 3 Shaft provides a unique mining challenge on account of the very thin middlings between the pay bands and the marginal values of the reef. It is uneconomic or impractical, because of the excessive heights, to mine the middlings using conventional stoping methods. The development of suitable mining methods is discussed with particular emphasis on the control of water inflow and the policy of not jeopardizing or sterilizing other reef horizons by the mining method implemented. No definite solution is currently available, but with the aid of instrumentation, computer analyses and mechanized mining equipment, the mine continues to attempt to maximize extraction and profits.

Jan 1, 1988

By S. Mohanty, K. Sarangi, S. Dash, P. P. Patra

Industrial effluent from various industries contains heavy metals that are a serious threat to humans, flora and fauna in water bodies, and the environment. The heavy metals are dumped after precipitation, which has serious environmental consequences. In this paper, a 2D axi-symmetry CFD model has been developed to study the extraction of chromium ion from industrial effluent, in a hollow fibre membrane, using Alamine 336 as the carrier and kerosene as the diluent. The Navier Stokes equation was used to predict the velocity profile of the aqueous and organic phases, and species transport equation, which considers both convective and diffusive mass transfer, was used to predict the concentration profile of the chromium ion in the computational domain. The distribution coefficient was experimentally determined at a pH 4, which was found to be the optimum pH. Numerical simulations were performed considering 11.11 mol/m3 of initial feed concentration for chromium ions and extractant concentration of 0.2 M. Simulations were carried out with various aqueous and organic flow rates, and validated with experimental data. Keywords: CFD, metal extraction, hollow fibre membrane, heavy metals

Jan 1, 2020

By G. T. van Rooyen

In this overview of materials engineering, the author, drawing on his long experience from his student days until the present (emeritus professorship), briefly recounts the main developments in this field: dislocation theory, fracture problems, and the development of alternative materials such as ceramics and polymers. He then takes a look at the future, in which he foresees a greater demand for materials engineers, and leading roles for universities and technikons in collaboration with industry.

Jan 1, 1996

By M. E. E. Douglas, A. K. Haines, D. I. Nicol, C. M. Olëm, W. M. Craig, G. D. Louw

A description is given of the design of the continuous ion-exchange demonstration plant at Blyvooruitzicht Gold Mine, including details of the process design, the column construction, and the control system. The operating and process results gathered over a period of seventeen months are summarized, and development work and modifications to the process are discussed. It is concluded that the system comprising continuous loading and continuous elution is technically feasible and can be scaled up with confidence.

Jan 1, 1978

By M. S. Shishvan, J. R. van Duijvenbode, L. M. Cloete, M. W. N. Buxton

Geochemical and mineralogical datasets from Tropicana Gold Mine, Australia, have been used to define ore fingerprints. VNIR/SWIR spectral data were represented by four normalised wavelength regions and were clustered to form spectral classes. Sequentially, these spectral class proportions within a block and collocated XRF data were clustered to form material types (fingerprints). The material types were related to an Equotip-BWi correlation. These correlations can be used to extrapolate a hardness signature and generate a BWi proxy for different blocks. The combined fingerprints and BWi proxy can assist as a tool for enhancing the prediction of comminution behaviour. They can explain specific domain-related hardness variations. For example, one material type could be separated into a softer (~15-18 kWh/t), and harder (>20 kWh/t) material blend. This was accomplished using the commonly overlooked VNIR region at 605 nm. This outcome has significance for blending strategies.

Sep 1, 2021

By M. Krasowska, W. Skinner, R. K. Asamoah

Understanding chemical interactions at solid-liquid interfaces have played a pivotal role in improving mineral flotation performance, increasing the rate of mineral crystallisation and profitable leaching of valued minerals and metals. This paper highlights gold leaching with links to surface and interfacial chemical processes occurring, and opportunities to maximise extraction while reducing usage of more recent scarce resources. From the review, there is a significant link between surface and interfacial processes and gold leaching performance. Evidently, gold leaching kinetics could be increased by changing leaching conditions, including manipulating the surface and interfacial interactions. Control of surface and interfaces during gold extraction could enhance rapid, smarter gold extraction and mitigate formation of passivation layers. Keywords: Surface and interfaces, refractory ores and concentrates, gold leaching, reaction mechanism and kinetics

Jan 1, 2020

By F. H. Touwen, N. C. Joughin

"Simulation is a technique for studying the operation of systems by synthetic experimentation. With digital computers it is possible to simulate even the complex production processes in gold mining. This has great potential in that it enables the investigation, analysis and comparison of mining systems to be done accurately, rapidly and at low cost. Two programs have been developed to simulate the principal underground production processes in gold mining.These are the simulation of any stope contract and the simulation of underground transport operations. The programs synthesize these mining activities from a large number of small unit operations. The stope contract program simulates rockbreaking by drilling and blasting and the cleaning of the panels by face and gully scraping. The transport program simulates the functions and movements of all vehicles running on rails on one underground level. The simulation programs provide an effective means for experimenting with mining activities."

Jan 1, 2014

By D. G. Krige

Recent publications have demonstrated the important role that can be played by a priori information of the grade levels, variability, and spatial patterns in adjacent or nearby areas in improving the quality of grade estimates for virgin or sparsely drilled areas. A research project was therefore conducted involving the collection and analysis of extensive sampling and borehole data from 7 reefs on some 30 Witwatersrand mines. This paper shows that the 'equivalent' log variance for the two-parameter lognormal model provides a good basis for the study and comparison of the levels and behaviour of relative variances. The trends of these against the corresponding log areas were found to form distinctive patterns, which are useful for these purposes. The patterns for the Basal, Vaal, Carbon Leader, and Main Reef Series form a reasonably close group, whereas those for the V.C.R.(particularly where the facies are mixed), B Reef, and Kimberley-Elsburg Reefs (particularly for narrow channel widths) do not always conform. The patterns shown by underground chip samples are also compared with those obtained from borehole cores. It is shown how this information can be used to improve the borehole valuation of new mines and of virgin areas in existing mines.

Jan 1, 1993

By N. B. Prenn, R. H. Robinson

"The model described is a design and economic planning tool for analyzing surface mineral deposits. Mineralization, topography, costs and significant geologic features are input to the model. The results are:(i) final pit limits yielding the maximum total profit,(ii) annual cut-off grades and plant sizing yielding the maximum present value, and(iii) annual maps of the pit and annual production statistics for the mine, concentrator and smelter.Additionally, summaries are printed of the block mining sequence and cash flow. A special feature is an option to include dump-leaching operations. Stockpiling of material can also be simulated by the model. The model is built around theories of dynamic cut-off grades and a pit design algorithm. The dynamic cut-off grades maximize present value by examination of all economic and physical constraints for the optimum combination. The pit design algorithm is a set of rules formulated to find the maximum value from a special graph. The graph is different from graphs of analytical geometry, being made up of points and arrows connecting some of the points. These graph elements describe the relationship between any point in the deposit and the material which must be mined to get at that point. The model was designed to bring together the interdependent theories of economics, pit design and production scheduling."

Jan 1, 2014

By K. M. Seiler

Automation in mining requires accurate maps of road networks on site. Because roads on open-cut mines are dynamic in nature and continuously changing, manually updating road maps is tedious and error-prone. This paper investigates the possibility of automatically deriving an accurate representation of the road network using GPS data available from haul trucks operating on site. We present an overview of approaches proposed in literature and test the performance of publicly available methods on GPS data collected from trucks operating on site. Based on shortcomings seen in all tested algorithms, a post-processing step is developed which geometrically analyses the created road map for artefacts typical of free-drive areas on mine sites and significantly improves the quality of the final road network graph.

Sep 1, 2021

By R. McGregor

You wouldn't start excavating before testing core samples, so why would you approve a project plan before all factors have been identified, reviewed and addressed? Even a champion sports team made up of the best players can't produce optimal results without a well understood and agreed game plan. Could an F1 racing team produce their outstanding performance without rigorous evaluation and testing of the factors for successful performance? Why would we expect a capital works project team to be able to get it right without an understanding and an involvement in setting and implementing the overall game plan and without an understanding of all stakeholder requirements? For International Power's Hazelwood (IPRH) mine in Victoria, the challenge was development and delivery of a 40 year mine plan, ultimately involving relocation of existing mine operations into an adjacent new coal field, land acquisitions and major environmental and other approvals to allow diversion of three streams, a highway, an Over Dimension route and other infrastructure in a political and environmentally sensitive atmosphere. The lessons from International Power Hazelwood's (IPRH) experience are: ? that the clear set of project principles and guiding values ensured delivery of a robust plan; ? a robust plan can withstand significant change; and ? value management (VM) played an important role in providing assurance, to all, that the plan was sound at both the strategic and micro levels. This Hazelwood mine project included five major VM workshops. The first was a critical review process in addition to design and cost reviews. This VM workshop was used to analyse, at a high level, the preferred coal mining sequence and design concepts, together with the interaction between design elements, risks and costs. In addition to this, the workshop provided an agreed common pathway for all downstream decisions. A second VM study was conducted to ensure that the proposed plan and design for relocation of the conveying systems from the existing mine into the new field were planned for optimum achievement from a whole of life cost, time, operational and maintenance perspective, plus the logistics of continuing operations while relocating assets. A third study followed to review the Conveyor Transfer Alliance and review functional design. A fourth VM study workshop was formed at the start of Phase 2 Alliance to ensure that the best value for money was being achieved through the current design, schedule and project arrangements and that all interfaces between parties had been reviewed and responsibilities were clear and understood. Other studies are outlined later in this paper. This paper details the evaluation criteria and processes used in the project evaluation that led to the WestField Mine Development.

Jan 1, 2007

By J. T. Nel

The Kroll process is the traditional method of producing zirconium metal by reduction of zirconium tetrachloride with magnesium metal. This paper discusses the production of zirconium metal in a plasma reactor. Anhydrous low-hafnium ZrCl4 and Mg metal were fed continuously to a 30 kW non-transfer plasma reactor at a rate of 0.31 kg.h-1. Due to losses in the system the recovery of crude product was 77.5 %. After purification to remove unreacted feed material and MgCl2 by leaching, >98 % pure zirconium metal powder was obtained. The overall recovery of purified Zr was 74 %. The conversion efficiency of the process was 95 %.

Jan 1, 2012

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery ? Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery ? Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2012

By R. D. Beck

The minerals industry needs the support of al sections of the population if it is going to be able to supply the new materials required for future development. It will achieve this support only if its image is good. Perceived images of the minerals industry are examined in respect of history, technology, environment, safety, education, and economics. Concern is expressed about the low technological image of the industry and the declining number of students enrolling in minerals-related disciplines. It is concluded that it is the professionals, through institutes like The South African Institute of Mining and Metallurgy, who must take the lead in improving the image of the minerals industry. The Presidential Address gives data to support this thesis; data that, is hoped, can be used in efforts to educate people about the minerals industry.

Jan 1, 1991