Search Documents

COUNCIL FOR 1989/90 President Dr O.K.H. Steffen President-elect Mr H.G. Mosenthal Senior R.D. Beck Vice Presidents Junior ].P. Hoffman Immediate Past President C.E. Fivaz Honorary Treasurer Dr H. Wagner

Jan 1, 1990

COUNCIL FOR 1987/88 President B.C. Alberts President-elect C.E. Fivaz Vice Presidents Senior Junior Dr O.K.H. Steffen H.G. Mosenthal Immediate Past President Dr H. Wagner Honorary Treasurer Dr H. Wagner

Jan 1, 1988

By Y. J. F. Haven, G. H. J. Kitson, D. G. Beadle

I have read this paper with considerable interest. By using an automatic instrument to assess the dust samples taken in South African collieries, the authors are ahead of the gold mining industry, which still uses the laborious method of microscopic assessment, with its limited accuracy, of the half-a-million dust samples taken each year. As the authors state, the result obtained from the photoelectric assessment of the samples is approximately proportional to the surface area of the respirable dust. However, modern theory is that, in assessing coal dust, it is the respirable mass which is important in determining the danger to health. Thus Table II of their paper is of considerable value in showing the relationship between the P.E.R. value and the mass concentration measurement. Unfortunately this table only gives the mean relationship. The important point is to know the scatter around this mean. If the scatter is small, then this mean value (for different operations) would have considerable value in converting from respirable surface area to respirable mass, but if the scatter is large, then such a conversion, using a fixed factor, will have little value. In the text the authors mention the range of values as being between 3 to 24, but without a statement on the number of samples used to determine this range and their distribution, this is a rather nebulous statement. I hope, in their reply, that the authors will give, in statistical terms, some statement on the overall correlation between these two parameters. I might add that at present a member of my staff is working on similar relationships for dust samples taken in gold mines. Another factor which may well be most important in determining the danger of dust levels in coal mines is the composition of the dust, specifically its quartz content. I understand that the authors have some information on this point, and to make their results of greater value in International comparisons of dust levels and the concomitant development of pneumoconiosis, it will be extremely useful if they could place this information on record. Even though, as I have said above, modern theory postulates that respirable mass is a better parameter to use than respirable surface area, the problem remains of how to measure this parameter with short time sampling, which, as the authors point out, is their preferred strategy for dust sampling and dust control. I know of no easily portable instrument, independent of external power supplies, which can, in 5 to 10 minutes, collect sufficient dust to enable it to be weighed accurately. Thus the authors' implied intention of continuing to sample by their present techniques and using their present parameter to report the results is, in my opinion, an entirely valid decision.

Jan 10, 1968

By G. T. G. Emère

The Harmony Gold Mining Company Limited employs approximately 29 500 people, including 27000 Black workers recruited from areas both within and beyond the boundaries of the Republic of South Africa. The problems arising from the control of this diverse and complex labour force have led to the need for a fully computerized labour control system. This paper describes how, with the aid of an extensive interrelated network of satellite minicomputers, together with ancillary peripheral user terminals and printers, the management of Harmony Gold Mine intends to meet these problems.

Jan 1, 1983

By P. C. Schutte, J. R. Smith

The objective of ergonomics is to enhance the effectiveness and efficiency with which human tasks are carried out. Furthermore, the objective is to improve desirable human values. This can be achieved by enhancing safety, reducing fatigue and stress, increasing comfort, increasing job satisfaction, having greater user acceptance and thereby improving the quality of life. Mechanization has influenced the prevalence of injury, mainly due to the application of human physical effort as the power source. With mechanization, the operator’s function is now essentially one of control rather than being an energy source, however the risk of injury has not diminished. Mechanization in itself has introduced inefficiencies, health risks and physiological stress. The major objectives of ergonomics are discussed through examples of acceptable and less successful implementation of ergonomics within mechanized mining. The influence of the machine system on the human is addressed and practical solutions to improve and optimize the interaction of the human and the machine are outlined. Furthermore, practical examples of control and display integration, anthropometric and biomechanic influences on design, orientation, posture and stereotypes are used to accentuate the advantages of the application of sound ergonomics principles to the specialised area of mechanized mining.

Sep 1, 2001

By B.E. Hall

Maximizing shareholder value has become a common aim for mining companies. This paper discusses the results of a number of studies developing strategic mine plans, covering a wide range of commodities, styles of mineralization, mining methods, and processing facilities, for single and multiple deposits. It has become evident that traditional methods and conventional wisdom often do not in fact achieve these goals. Operating policies at many mines ensure that shareholder value is not maximized. Changing the overall strategy can provide significant value gains. Typically, the new optimal plan involves a significant increase in the cutoff grade, at least in the earlier years. An increase in the underground development rate or open cut stripping rate is often associated with this, at least in the short term, to establish the new strategy. Cost minimization is found to be counter-productive. Counter-intuitive plans are often found to be optimal. For example, optimal cutoffs for different parts of an underground mine may be significantly different, even if mineralisation and cost structures are similar. Sub-optimal strategies are also frequently found to have a significantly greater financial risk than optimal plans, which have been found in many cases to be relatively insensitive to changes in major value drivers, such as metal prices. This paper shows how identifying and then operating within the framework of an optimal strategic plan can have substantial benefits over being continually driven by short-term tactical issues.

Jan 1, 2009

By Mr P. W. J. van Rensburg

SOUTH AFRICAN NATIONAL COMMITTEE ON TUNNELLING In 1970, the South African Institution of Civil Engineers, the South African Institute of Mining and Metallurgy, the South African Institute of Mechanical Engineers, and the Geological Society of South Africa held an international conference on tunnelling, known as Tuncon 1970. SUID-AFRIKAANSE NASIONALE TONNELBOUKOMITEE In 1970 het die Suid-Afrikaanse Instituut van Siviele Ingenieurs, die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie, die Suid-Afrikaanse Instituut van Meganiese Ingenieurs en Die Geologiese Vereniging van Suid-Afrika 'n internasionale konferensie in verband met tonnelbou gehou, wat bekend gestaan het as Tonkon 1970.

Jan 5, 1974

By L. K. Smith, E. M. de Kock, J. van der Walt

A systematic approach to the analysis of alternative methods of ventilating and cooling large hot mines is presented. The important factors that have a bearing on ventilation and cooling requirements and practices, such as air flow through the mine, geographical distribution of eat loads, and micro-ventilation considerations, are dealt with. The analysis of these factors leads to definitive ventilation and cooling strategies, air and water process design, specifications of details, and designs of the associated plant and equipment.

Jan 1, 1983

By H. White

The applicability of ground penetrating radar (GPR) in numerous qualitative applications has been demonstrated over the past five years in the South African mining industry. These applications include the delineation of faults and dykes, fracture mapping, delineation of shear zones, mapping of depth of weathering, and the delineation of contact between different rock types. The qualitative nature of the data collected using existing commercial GPR systems, often relying on expert interpretation, has however mitigated against the full scale routine application of GPR in the mining industry. The recent development of the RockRadar system by ISS International has, to a large extent, overcome these problems. The result is that quantitative rock-mass studies can now be performed with the RockRadar system.

Jan 1, 1996

By Paul Fouchè

Contents ?Purpose ?Introduction ?Why manage a mineral resource ?Sampling or tracking from source ?How can RF tracking help ?Project Goals ?RF System ?Tracer Layout ?Antenna

Jan 1, 2005

By C. J. Lenz

The results of prospecting operations involving geological data and a large number of geochemical determinations of the metal content of soil samples are plotted and evaluated by computer. Anomalous areas are identified in each type of environment by selecting probability or population boundary values from frequency distributions. The anomalies are plotted to permit correlation with geographical or geological features. Ranking of prospecting targets is made using geographic pattern, geology, absolute value and metal ratios. Three short case histories are presented.

Jan 1, 2014

By B. C. Alberts

Rapid and effective handling of run-of-mine, waste, and treated materials is vita.! to every step of resource development and recovery. Modern mine managements have planned and engineered systems for the handling of ever-larger tonnages. Where traditional methods have not proved to be costeffective and adequate, managements have pioneered the development of new materials-handling systems in the mining industry.

Jan 1, 1983

By O. I. Rychkova, M. N. Sycheva, E. V. Poryadochnova, G. V. Sedelnikova

Deposits of copper-porphyry type occupy a leading position in the mineral resource base of the world copper industry. They are characterized by large and gigantic scales, often complex composition, their development is carried out in an open way. The raw material base of the Russian copper industry is mainly sulfide copper-Nickel and copper-pyrite ores. Exploration of copper-porphyry deposits and the creation of long-term large mining facilities on their basis is one of the most promising and priority tasks for the Russian industry. This task is especially acute for the copper enterprises of the Urals in connection with the depletion of copper - pyrite ore reserves. In recent years, Russia has carried out a large complex of studies on the composition and technology of processing of copper-porphyry ores of different subtypes. In this work the complex poor copper-molybdenum-gold ore of one of the deposits is investigated. The chemical and mineral composition of the ore containing 0.49% copper, 0.020% molybdenum, 0.39 g/t gold, 5.85 g/t silver was determined. The forms of finding metals and their distribution by size classes are established. The dependence of extraction of metals into concentrates of collective-selective flotation on the size of ore grinding, pH of the medium, reagent consumption is shown. Under optimal flotation conditions, copper concentrate with 18.6% copper content and 92.32% extraction and molybdenum concentrate with 21.5% molybdenum content and 73.4% extraction were obtained. With a high concentration of molybdenum in selective flotation products, it is possible to conclude about the expected molybdenum concentrate with a content of 45% and a recovery of 70%. The associated extraction of gold and silver into copper concentrate is 76.8 % and 73.4%. Keywords: Collective-selective flotation, copper, molybdenum, porphyry ore, grinding, pH, reagents

Jan 1, 2020

By B. M. Munyungano

Rössing Uranium Mine operates a recovery circuit with continuous ion exchange followed by solvent extraction. Serious organic degradation problems were encountered during 1985/6, 2000 and 2005 in the solvent extraction plant. The preferential loss of the tertiary amine extractant was observed during the above-mentioned period. Previous investigations revealed that the tertiary amine was breaking down to nitrosamine, which cannot take part in the exchange reaction with U3O8. A reduction in the redox potential of the solvent extraction plant feed to below 500 mV halted this preferential loss. A lot of effort has been made to try and understand the actual mechanism for nitrosamine formation. Current understanding for the degradation is that formation is due to high nitrates on the strip side of the circuit emanating from nitrates from the precipitation process using ammonia. It is the current belief that pH lower than 3.7 on the strip side results in loading of nitrates onto the solvent. If oxidizing conditions prevail on the extraction side of the solvent extraction circuit, the tertiary alamine will then degrade into nitrosamine. This phenomenon is yet to be established and verified. It has, however, been established that the above process is brought about the following conditions ?High redox potential greater than 550 mV predominately caused by a high Fe3+/Fe2+ratio (4:1) ?Perception that if Fe2+<0.5 g/lit will contribute to high redox ?High concentrations of NO-3 in the conc eluate (feed to SX)/ammonium sulphate (NO-3> 4 g/l based on historic values) ?Presence of Mo as a catalyst ?Tests also have proved that the presence of nitrous acid in a concentration of 1 g/lat 550 mV leads to formation of nitrosamines from alamine.

Jan 1, 2007

By D. Sager

Middleburg Ferrochrome (MFC), a company in Samancor Chrome, commissioned a new ferrochrome smelter in March 2009. This is a 60 MW DC-arc furnace with a DC power supply for the smelting of Transvaal chromite ore fines. With the benefit of 12 years&apos; experience with this technology while operating a 44 MW DC-arc furnace, MFC mitigated all known challenges and considered up-scaling risk in the new plant, which had a rapid ramp-up to full power in 02 of 2009. Good operating practices, as made possible by robust equipment selection, including a thyristor rectifier set of proven technology, and operation with optimal slag chemistry, leads to a safe and effective plant operation. With the optimized furnace design and a correctly sized power conditioning system, using only standard (static) harmonic filters and a correctly sized smoothing reactor, the arc furnace is not a &apos;dirty load&apos; for the utility, staying well within IEC limits for power quality. A patented arc compensation system is installed and allows for full arc position control (to compensate for magnetic field induced arc deflection) so that a symmetrical crucible is maintained, significantly benefiting refractory life. The principal benefits gained from the MFC process is the fact that ore fines are processed, without metallurgical coke, and higher chrome recoveries are achieved compared to other smelting technologies when using a DC open arc for smelting. Keywords Samancor Chrome, Middelburg Ferrochrome, ABB, smelting, DC arc furnace, arc compensation, power factor correction, anode, harmonics, thyristor, reactor, maintenance, refractory, ores, reductants.

Jan 1, 2010

By D. J. C. Taylor, R. A. Kruger

Unbridled mining operations can have a serious negative impact on the surroundings. With the recent increased awareness of the need for environmental conservation and the resulting advances in environmental control, the mine planner has new tools at his disposal for the successful implementation of mining projects while avoiding negative environmental effects. This paper discusses the environmental strategies adopted in the planning and commissioning of a trial underground coal mine. The minimization of negative environmental effects is demonstrated and, where applicable, environmental benefits are examined.

Jan 1, 1986

By A. J. Vietti

"Drought conditions and the possible lack of sufficient raw water supply are a constant reminder to the Southern African diamond miner of the need to minimize raw (new) water input while maintaining or expanding mine throughput.Since water input volume is directly related to water output (loss) volume, mainly to the tailings, it is obviously beneficial to dewater the tailings as much as possible. However, this may not always be as easily achieved as first thought. Owing to the unique mineralogy of each kimberlite deposit and the unique chemical profile of each raw water source, dewatering of the slurry is not a standard process that can be applied equally across the entire diamond industry.This paper presents a first-step strategy that kimberlite diamond mine operators should consider and apply to meet and exceed their watersaving targets. Introduction A common metric for measuring water use efficiency in a metallurgical plant is the amount of raw water used per ton of head feed treated (m3/t). The metric includes all water recycled from the dewatering process and from the tailings storage facility (TSF), and the only inputs are tons of ROM ore and cubic metres of raw water make-up to replace water lost to evaporation, seepage, and lock-up at the TSF (Figure 1).The volume of new raw water available to the process is not unlimited and a maximum monthly allowance is typically set during the mine permitting process. Consequently, if the volume of water lost exceeds the volume of new water available or alternatively, in times of drought where the allowable volume is unavailable, the plant has no other option but to reduce throughput.However, if the plant operator is able reduce the volume of water lost to the TSF, the plant will have additional capacity to either increase tonnage throughput or sustain nameplate capacity during periods of severe drought. The obvious conclusion, therefore, is to reduce the volume of water lost to the tailings by improving the efficiency of the dewatering process (typically gravity thickening) simply by increasing the density of the tailings being discharged. In practice, however, the unique mineralogy of each kimberlite deposit and the chemical profile of the raw water source used imply that at some mine sites, solid/liquid separation (or settling) of tailings slurries at the dewatering process is more easily achieved than at others. In these cases, simple practical steps such as firstly improving the flocculant reagent make-up and dosing control, and secondly focusing on thickener discharge control, are the only requirements for enhancing water recovery at the dewatering circuit. At other mine sites however, solid/liquid separation of the tailings may not be achieved at all, in which case efforts to increase water recovery by improving reagent dosage and thickener control would be fruitless unless the colloidal properties of the thickener feed slurry are modified."

Feb 1, 2019

By M. G. B. Wheeler

SYNOPSIS This report outlines the development of a model to simulate the radiometric sorting of gold- and uranium-bearing ores. The developed program indicates the optimum mass, reject percentage, and expected reject gold and uranium grades for a radiometric sorter. It achieves this by statistical analysis of the data gathered from a large sample of rocks in the required size range for a particular mine. The program can be used in the optimization of existing sorters, as a design tool for new radiometric sorters, and in feasibility studies on radiometric sorting.

Jan 1, 1989

Traditionally, the term `total system&apos; design applied to comminution conjures images of a design that addresses the usual business and operational drivers, including health, safety and environment (HSE), capital cost, operating cost, throughput and product size. In terms of the physical process, the mine to customer type studies also exemplifies an approach that satisfies a normal `total systems&apos; approach. As an industry there are drivers that are forcing a re-consideration of what we regard as our total system. This modification of drivers will require changes in approach and implementation to provide the best solutions. Some of the major changes that impact the drivers are shortage of skilled personnel, changing social attitudes to remote mine site work, greenhouse gas emissions (GHGE), quality of available orebodies and geographical location of new mine sites. One approach to the challenges presented by the changing business environment is to expand the system envelope around comminution to ensure that comminution, in its widest sense, helps to meet the new realities. Background to the new drivers and constraints is provided and some of the appropriate responses are examined in relation to the impact on the total system.

Jan 1, 2007

By S. Rupprecht, G. Rapson

Long blast hole drilling has been successfully implemented since the 1950s in caving operations, steeply dipping wide reefs and boxhole/raise developments worldwide. However, when applying long hole drilling to narrow tabular reefs, the challenges of achieving high economic drilling rates, combined with acceptable accuracy and appropriate powder factors have yet to be overcome. The focus in this paper is the selection, application and optimization of long hole drilling equipment at mining operations shallower than 2 000 meters. The drilling, blasting and cleaning operations have to be optimized as a process if maximum production at minimum per unit cost is to be achieved. For this to be possible, it is essential that the mine design and layout match the mining process being implemented. The critical parameters affecting the sustainable implementation of long hole drilling in stoping applications for platinum mines are improved safety and higher production rates compared to conventional methods. In terms of drilling, both top hammer and down-the hole hammer configurations have been considered. For economic drilling, the benefits of monitoring and optimizing performance (i.e. drill bit rotation, thrust, and percussive power) for specific rock types are discussed. While the drive is for longer, more accurate, smaller diameter holes to reduce drilling costs, the design of appropriate blast hole patterns and the corresponding charging and initiation systems is crucial for success. The effect of hole diameter and pattern on the powder factor, when comparing small diameter, shorter holes versus large diameter, longer holes, is a major factor in achieving good blasting results. Once appropriate drilling and blasting have been implemented, the cleaning process becomes a potentially critical operation to ensure the production, cost and safety goals are met. Hence, the blast hole pattern and charge have to be integrated for optimal fragmentation to suit the cleaning cycle for maximum production output. Providing that long blast hole drilling is applied as a process in a planned, committed and well-managed manner, the benefits in safety, production and cost over conventional methods should be achievable. However, if the implementation process is not planned and supported by all parties concerned, it will not be possible to succeed in the new operation. Hence, an implementation or roll-out plan of new technology is crucial for success.

Jan 1, 2004