Search Documents

By M. K. Larson, J. K. Whyatt, R. B. Langston, J. C. Johnson, H. Kirsten, T. M. Brady

An experiment is described in which hollow inclusion cells (HICells) were used to measure stress in a jointed rock mass during drift development at the Stillwater Mine, Nye, MT, USA. Two HICells were installed in the footwall approximately two drift widths ahead of the face. One HICell was over cored and then immediately tested in a biaxial chamber. The other HICell was left in place and monitored as the drift was excavated in three advances, each one-half the width of the drift. Strains were recorded hourly by a datalogger. Results show that there was little stress change during the first and second drift advances, but that a large stress change occurred after the third advance. The measurements also showed that the in situ principal stress directions lined up with regional geologic structures. Stress changes during face advance were likely caused by deformation along localized joint sets and inelastic deformation near the face.

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A. 3 Program Description The computer program developed to simulate events in the case of fire in the mine is described in this section The description is divided into three parts. 1. Program Capabilities This part summarizes what inputs can be changed, what outputs can be obtained and demonstrates program flexibility through suggested uses.

Jan 1, 1976

Miners, like everyone else, must be able to see well in order to work well. But simply hauling bigger and brighter lights into the mines does not necessarily produce better mine illumination. This chapter tells why. Increasing the power of the light source can create problems of portability, glare, adaptation and contrast. This chapter also discusses some ways to increase illumination by Improving the reflectability of walls, roofs and other exposed surfaces. In Chapter IV you learned that the "brightness" of a room or work area was really a matter of how much light was reflected from the walls, roof, and other surfaces. Therefore, if you want to Improve visibility you should increase the amount of reflected illumination. O HOW DOES ONE DO THAT? One way of Increasing reflected illumination would be to increase the power of the light source.

Jan 1, 1976

A survey of roof and pillar conditions in underground limestone mines in the United States has revealed that bench mining of the floor between pillars can cause instability in the pillars at the perimeter of the benched area. Increased loading of these pillars was observed at several mines. Large inclined geological structures that are exposed in pillar ribs were observed to contribute to pillar instability. The paper describes a study that was carried out using numerical models to assess the effects of bench mining on pillar load and stability. It was found that the benched pillars shed load onto the surrounding pillars owing to their reduced stiffness. The pillars at the perimeter of the benching area will start shedding load as soon as benching increases the height of one side of the pillar. A case study is described which shows the effects of bench mining on limestone mine pillars.

Jan 1, 2007

By Travis Q. Lyday

Fiji has been an independent country within the British Commonwealth of Nations since 1970. It consists of an archipelago of more than 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets, to the larger mountainous islands of Kandavu, Taveuni, Vanua Levu, and Viti Levu of volcanic origin. The islands of Fiji straddle the 1800 meridian about 1,800 kilometers south of the Equator in the part of the southern Pacific Ocean known as Melanesia. The production of gold and silver from the Emperor Mine at Vatukoula on the island of Viti Levu, the main island of Fiji, remained Fiji's only metallic mineral producer. Mining began at the Vatukoula site in 1933, producing 124 million troy ounces of gold and 147 thousand troy ounces of silver by yearend 1985.

Jan 1, 1987

By Robert P. Vinson, John C. LaScola, Fred N. Kissell, Edward D. Thimon

The face ventilation measurement method developed by the Bureau of Mines involves releasing a small volume of tracer gas (SF6) on the off-curtain side of the working face at the start of the mining cycle. At the same time, gas bottle samples are taken in the immediate return airway. The gas samples are analyzed, and a curve is drawn of SF6 concentration versus time. From this curve, the percentage of gas removed per time is calculated. A curve showing a high percentage of the tracer gas removed in a short period would represent a well-ventilated face. The face ventilation measurement method was tested in a full-scale mine entry model. Subsequently it was used underground to evaluate the spray-fan ventilation system and in an MSHA test facility to test machine-mounted scrubbers. The method was shown to be a simple and effective way of evaluating face ventilation systems.

Jan 1, 1980

By R. V. Lundquist

Past reports by the Bureau of Mines have described the extraction of alumina from numerous aluminum silicate materials by the lime-soda sinter process. The results from pilot-plant investigations of six materials, with alumina-to-silica mole ratios from 0.3 to 8.7, indicated a relationship between the alumina-silica ratios and the processing characteristics of the sinter. A series of laboratory tests was conducted to define this relationship. Sinter and leach tests determined that an alumina-to-silica mole ratio of 0.90 or greater resulted in the best alumina and soda recoveries while leaving the leach slurries practically free from any tendency toward gelation. The widely different chemical and mineralogic properties of the various aluminous materials used in compounding the mixes had no perceptible effect on the leaching characteristics of the sinter. The blending of low-cost, high-alumina materials with aluminum silicate materials to give an alumina-to-silica mole ratio of 0.90 or greater would improve alumina and soda extraction and minimize operating problems in the lime-soda sinter process.

Jan 1, 1970

By Clarence Hall, Spencer P. Howell

This bulletin deals with the characteristic features of the principal explosives used in mining and engineering operations, and espe- cially with the tests that show the suitability of different classes of explosives for different kinds of work. The Bureau of Mines pub- lishes the report as one of a series dealing with tests of explosives and methods of reducing the risks involved in the use of explosives in mining operations. The application of explosives to engineering and mining opera- tions has increased rapidly in recent years. According to a pre- liminary report issued by the Bureau of the Census, 469,000,000 pounds of explosives was manufactured in this country during the year 1909, and the greater part of this production was used for industrial purposes. In large engineering projects and in mining operations requiring the use of explosives the selection of a suitable explosive from the many varieties offered for sale is of fundamental importance. Vari- ous considerations are involved in the selection of an explosive of proper class for the blasting to be done. Many explosives suitable for quarry work are unsuitable for use in deep mines or in close workings. In metal mining and in driving tunnels the character of the gases evolved by the explosive on detonation is an important consideration. An explosive for use in gaseous or dusty coal mines must be formulated and compounded so that its flame temperature and the height and duration of its flame are reduced enough to per- mit its being used with comparative safety. In wet workings or in submarine blasting explosives impervious to moisture are requisite. In extremely cold climates explosives that do not require thawing are desirable, provided they are equally good in other respects. An essential requirement of all explosives, especially of those for use in tropical countries, is that they shall remain stable without change in chemical or physical characteristics.

Jan 1, 1913

By S. J. Schatzel

In an effort to increase productivity, many longwall mining operations in the U.S. have continually increased face lengths. Unfortunately, the mining of larger panels may increase methane emissions. The National Institute for Occupational Safety and Health (NIOSH) conducted a mine safety research study to characterize and quantify the methane emissions resulting from increasing face lengths in the Pittsburgh Coal-bed. The goal of this research effort was to provide the mine operator with a method to predict the increase in methane emissions from the longer faces for incorporation of additional methane control capacity into the mine planning process, if necessary. Based on measured methane emission rates of 0.066 m3/s (140 cfm) for a 315 m (1032 ft) face, projected longwall face methane emission rates were 0.090 m3/s (191 cfm) for a 366 m (1200 ft) face, 0.106 m3/s (225 cfm) for a 426 m (1400 ft) face, and 0.124 m3/s (263 cfm) 488 m (1600 ft) face.

Jan 1, 2006

Aluminum alloys are used in two broad classifications: wrought and cast. Wrought alloy products, which are formed into final shape by rolling, forging, extruding. etc., contain low percentages of alloying elements; whereas cast aluminum products, which generally are not worked before use, may contain higher percentages and a somewhat different selection of alloying elements. For example, wrought aluminum alloys usually contain less than one percent silicon and cast alloys contain as much as 18 per-cent silicon. While there are good techniques available for separating aluminum alloys from mixed scrap, there are no efficient ways to separate wrought aluminum from cast aluminum. The high levels of silicon, iron) copper, and zinc from the cast alloys make wrought-cast mixtures unacceptable for wrought alloy production. Consequently, separated wrought aluminum scrap commands a premium price on the market. Since increasing amounts of mixed aluminum alloys are being recovered from automobile scrap, this separation is important for efficient recycling of these alloys. Approach The difference in thermo-mechanical properties between the two classes of aluminum alloys is used as the basis for the separation process. Casting alloys lose their ductility within a certain temperature range while wrought alloys remain ductile. As temperature increases, aluminum alloys gradually become weaker, and at a certain temperature, each alloy loses strength and ductility due to incipient melting in localized areas. For casting alloys that temperature generally lies between 520° to 560° C, but it is above 600° C for most wrought alloys. Mild crushing, therefore, in the proper temperature range will result in complete fragmentation of the casting alloys but only plastic deformation of the wrought alloys. A simple screening step then is used to separate the oversize wrought pieces from the fragmented cast alloys.

Jan 1, 1984

This report, which updates and supersedes the Office of Surface Mining's 10-year progress report published in 1987, deals with the accomplishments of the regulatory and abandoned mine land reclamation programs during the first 15 years of the Surface Mining Control and Reclamation Act of 1977 (SMCRA). Part 1 is an illustrated description of on-the-ground accomplishments; Part 2 presents statistical information for the 15-year period. The data in this statistical report are organized in two sections: national statistics and state statistics. The national statistics provide an overview of coal mining and the implementation of SMCRA since 1977. The information reported for the states presents a brief description of the coal reserves in each area, accompanied by detailed statistics and graphs that relate each state to the nation as a whole. The statistics compiled in this report are from the Office of Surface Mining's files, computer data systems, and annual reports. During the early years of the program, many of the data categories were evolving and changing; therefore, data reported over the 15-year period are not complete for all states for all years, and where data was unavailable or zero, a dash (-) is shown for that item. The data sources used to compile the tables and graphs are listed and described in detail on page 76. Due to the number of requests for this information in the past, statistical information about coal mining and its regulation will be available each year as an appendix to the Office of Surface Mining's Annual Report to Congress. Beginning in Fiscal Year 1993, this information will be compiled and published on an annual basis. For more information about this report, call or write the: Public Affairs Office Office of Surface Mining 1951 Constitution Ave., N. W. Washington, D.C. 20240 (202) 208-2553

Jan 1, 1992

By Launa Mallett

This paper introduces a method for teaching workers to communicate necessary information when giving or receiving emergency warning messages. Research has shown that when an emergency occurs, people may not get the information they need to take appropriate action. Interviews conducted with 48 underground coal miners who had escaped mine fires revealed that the warning information provided was inadequate. In some cases, sufficient information was not provided to the endangered miners. At other times, miners failed to ask for information they needed to plan and execute effective escapes. Researchers from the NIOSH Pittsburgh Research Laboratory have been studying the content of emergency warning messages and have developed an emergency communication protocol. A training intervention that presents the protocol and related mental cues is being evaluated for effectiveness in improving the content of emergency messages. In this paper the protocol is presented and the training package described. The evaluation procedures and a summary of the analyses conducted to-date are also provided. The training package was developed for use with underground coal miners, but could easily be modified for emergency communications training in other settings.

Jan 1, 2000

By John N. Murphy

In fiscal 1996, the US Congress directed that the US Bureau of Mines (USBM) be closed. Certain functions were reassigned to other agencies. The remaining employees were separated and the unoccupied sites were decommissioned. As a result, 12 locations were closed and about 1,200 employees were terminated in March 1996. About 600 employees at five locations were reassigned to other federal agencies. This article provides a summary of the continuing functions, the agencies involved and the points of contact for each continuing function. The functions that were discontinued are also identified.

By T. Brady, R. Langston, J. C. Johnson, H. Kirsten

An experiment is described in which instrumented rock bolts were used to measure strain in the rock mass during drift development at the Stillwater Mine, Nye, Montana, USA. Two strain-gauged rock bolts were grouted into the middle of the rib next to the face. The drift was excavated in three advances, each one-half drift wide. Strains were recorded hourly by a data logger. Results show that the average change in axial bolt strain for the first and second advance was about the same and that there was almost no change in strain after the third advance. Bending strain was observed 19 cm from the head of the bolt.

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

5. General Escapeway Requirements 5.1 Escape Routes Present escapeway regulations state "Every mine shall have two separate properly maintained escapeways to the surface which are so positioned that damage to one shall not lessen the effectiveness of the other, or a method of refuge shall be provided when only one opening to the surface is possible." "Escape routes shall be a. Inspected at regular intervals and maintained in safe, travellable condition, b. Marked with conspicuous and easily read direction signs that clearly indicate the ways of escape." "Application. "Regular" intervals means at intervals no greater than monthly where conditions are stable and oftener where conditions may change." "Designated escapeways inclined more than 30* from the horizontal shall be equipped with stairways, ladders, cleated walkways, or emergency hoisting facilities." As can be noted in present and proposed regulations there must be two separate properly maintained escapeways. In most operations, the escapeways will consist of one route that is the normal travelway used in day to day operations. The second route is usually a return airway through old work areas. Based on this generally accepted practice, we will designate the two types as primary and secondary.

Jan 1, 1976

By A. T. Iannacchione

Designing coal pillars to provide resistance against overburden and gob loads has long been an aim of rock mechanics engineers. This requirement has become more imperative as greater overburdens are encountered and when mining in stiff coal-bearing strata. Current design procedures rely on theories of coal pillar behavior that take into consideration a common hypothesis. This hypothesis states that the elastic core is surrounded by an inelastic yield zone. The distribution of stress at low-to-moderate pillar loads has been effectively defined by this hypothesis. However, it suffers greatly when applied to large width-to-height (w/h >lo) coal pillars under considerable overburden (>500 m) . In these situations, the hypothesis says the elastic core can achieve unrealistic stress states giving the pillars extremely high calculated strength. A growing body of field studies has shown this is not the case. It has become clear that same other mechanism must be involved. It is the purpose of this paper to discuss the importance of an interface slip mechanism between the coal- bed and the surrounding strata in controlling the extent and pattern of stresses and deformations in a coal pillar.

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 9 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY; PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2;1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AROUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11;1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS 0F THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION.

Jan 1, 1977

By an Slo, J. J. Forbes

"INTRODUCTION This is the first of a series of information circulars dealing with the control of roof and the prevention of accidents from falls of rock and coal. These circulars are being published to focus attention of the coal-mining industry on this most prevalent source of fatalities and injuries and to present factual information that should be helpful in reducing loss from these causes.Records of fatal accidents in the coal mines of the United States, from all causes, have been kept since 1906; during this period approximately 30,000 men have been killed by falls of rock and coal in the bituminous-coal mines, and more than 7,000 men have lost their lives in the Pennsylvania anthracite mines from the same causes. From 1906 to 1930, about 900 men were killed annually by falls of rock and coal in bituminous-coal mines, and about 200 men were killed annually in anthracite mines during the same 25-year period. From 1931 to the present time, the number killed annually from falls of rock and coal has averaged more than 500 men in bituminous-coal mines and about 125 men in Pennsylvania anthracite mines.Numerically the record of accidents from falls of rock and coal shows improvement, but on a percentage basis and on a million-man-hours-of-exposure basis little, if any, improvement has been made during the past 40 years. The cold fact is that, year after year, about 50 percent of all those killed in coal mines in the United States lose their lives from falls of rock and coal."

Apr 1, 1948

By Donald P. Tuchman

The U.S. Bureau of Mimes is investigating Fourier transform infrared (FTIR) spectroscopy for on- filter quartz analysis of respirable dust. A custom accessory is described for full-face examination of filters utilizing a large-diameter infrared (IR) beam. The accessory positions samples to match diameters with that of the diverging analytical beam. Sample absorbance is then measured. With nonuniform deposition of dust on collection filters being a major issue for such analyses, this approach is the most direct way to accomplish sample area averaging. The approach is unconventional since it utilizes large-beam geometries instead of the usually desired minimized beam dimensions. The issues and problems involved in the analysis of quartz on a filter matrix are discussed. Absorption bands chosen, light-scattering effects, curved baselines, random noise, interference fringes, and possible solutions to technical difficulties are the topics covered. The more significant findings include a 20-pg detection limit for quartz when the custom accessory is used and minimal occurrence of light-scattering effects at low wavenumbers. The custom accessory performance was satisfactory and merits further work. With continued research, an on-filter method for quartz analysis of respirable dusts seems achievable.

Jan 1, 1992

By R. Larry Grayson

Barrett EA, Kowalski KM [1995]. Effective hazard recognition training using a latent-image, three-dimensional slide simulation exercise. Pittsburgh, PA: U.S. Department of the Interior, Bureau of Mines, RI 9527. NTIS stock number: PB95-170379. Beus MJ, Orr TJ [1995]. Computer modeling and analysis of the Greens Creek Mine, Admiralty Island, AK. Spokane, WA: U.S. Department of the Interior, Bureau of Mines, RI9530. NTIS stock number: PB95-176418. [ ]